Uploaded February 2025 | Updated November 2026, 1 hour ago
🛍️ Lectronz store: lectronz.com/stores/theretrochannel
. Revisiting the scart and sync mods for the 1084 (again).
🛠 Tools and kit: patreon.com/posts/tools-and-kit-77570017
💬 Discord: discord.gg/393FYaM6gM
😎 Ad-free, early access: patreon.com/theretrochannel
🔗
Adrian's video: youtube.com/watch?v=gISS9JsnRX8
Matt (Retrobits) channel: youtube.com/@retrobitstv
Previous video (old mod): youtube.com/watch?v=GP2Z7Y1ZBW8
1084S instructions and pics by acadiel: imgur.com/gallery/1084s-scart-mod-component-locations-xMcx2ZE
🔗
-----------
Instructions:
Updated: Jul 29 2025
Sync and scart mods for the Commodore 1084 (Philips versions)
Parts Required:
2x 390R 1/4W resistors
1x 1K 1/4W resistor
1x 1N4148 Diode (or equivalent)
1x Scart connector e.g. aliexpress.com/item/1005004046566803.html (LR ear)
Additional parts required for 1084 (MONO) version:
3x 5K6 1/4W resistors
1x 22K 1/4W resistor
NOTE: Some jumper links and parts might already be installed, if that is the case and they are the correct value you can skip to the next step.
1. Install 390R resistor at R210 (behind scart connector)
2. Install 1K resistor at R220 (behind scart connector)
3. Install jumper links at 9270, 9274 and 9275 (behind scart connector)
4. Install 390R resistor at R504 (behind RCA jacks) -OR- if R504 does not exist, install jumper link at 9206 (behind RCA jacks)
5. Remove jumper links at 9289 (behind scart connector) and 9290 (towards middle of board) if installed
6. Install 1N4148 diode at 9290, with the band facing towards front of monitor
6N. NTSC ONLY: If R232 (mid-left of board) is in the "NTSC" position, move it to the "PAL" position. If your board does not have these labels you can ignore this step
---
STEREO ONLY:
7S. Remove right channel audio and ground wires from scart footprint - required to install the scart connector
8S. Solder the right channel audio wire to the existing wire at ▲91, and audio ground wire to the existing wire at ▲78 (both are behind the scart connector - remove the audio amplifer board for better access)
9S. Install scart connector
---
MONO ONLY:
7M. Install 5K6 resistors at R305, R306 (behind scart connector), and R307 (behind RCA jacks)
8M. Install 22K resistor at R303 (behind scart connector)
9M. Install scart connector
---
OPTIONAL MOD to enable fast blanking override using VCR switch:
Parts required:
1x 10K 1/4W resistor
1x 1N4148 Diode (or equiv)
1x small length of wire
1x 2.4V Zener diode*
1x 1K5 1/4W resistor*
*these may already be installed - see steps 1 and 2 for details
1. Double check R575 (towards middle of board) is a 1K5 resistor (brown, green, red, gold). Otherwise remove R575 and install a 1K5 resistor
2. Double check D576 is a 2V4 Zener diode. If a resistor is there, remove and install a 2V4 Zener with band towards rear of monitor
3. Solder a 10K resistor and 1N4148 diode in series with diode band facing away from resistor
4. Connect 10K resistor to middle pin of SK5 (VCR switch)
5. Solder a length of wire from the 1N4148 diode (band side) and connect it to jumper link 9290 on the side towards the front of the monitor
** Make sure to properly insulate the resistor and diode with heat shrink so it doesn't short to anything on the board and route the wire and components away from the high voltage area of the PCB (flyback area).
* To use SCART for composite, SCART pin 16 must be 0V, front switch set to CVBS, and (if you did the fast blanking mod) VCR switch off
* To use SCART for RGB without fast blanking (SCART pin 16=0V), front switch must be set to CVBS and VCR switch on (requires fast blanking mod)
* To use SCART for RGB with fast blanking (SCART pin 16=1.5-3V), front switch must be set to CVBS (VCR switch doesn't matter)
* To use DIN jacks with H+V or C-sync, set the front switch to RGB and VCR switch off (if you did the fast blanking mod)
* To use DIN jacks with composite for sync, set the front switch to CVBS, VCR switch on (requires fast blanking mod) and input composite to scart pin 20 or composite jack
----------
🎞
0:00 Intro
5:45 Removing the old mod
7:18 Installing the new mod
15:49 Testing the new mod
17:51 The fastblanking override mod
24:33 Testing fastblanking override
🎞
Thanks for watching!
🛍️ Lectronz store: lectronz.com/stores/theretrochannel
. Revisiting the scart and sync mods for the 1084 (again).
🛠 Tools and kit: patreon.com/posts/tools-and-kit-77570017
💬 Discord: discord.gg/393FYaM6gM
😎 Ad-free, early access: patreon.com/theretrochannel
🔗
Adrian's video: youtube.com/watch?v=gISS9JsnRX8
Matt (Retrobits) channel: youtube.com/@retrobitstv
Previous video (old mod): youtube.com/watch?v=GP2Z7Y1ZBW8
1084S instructions and pics by acadiel: imgur.com/gallery/1084s-scart-mod-component-locations-xMcx2ZE
🔗
-----------
Instructions:
Updated: Jul 29 2025
Sync and scart mods for the Commodore 1084 (Philips versions)
Parts Required:
2x 390R 1/4W resistors
1x 1K 1/4W resistor
1x 1N4148 Diode (or equivalent)
1x Scart connector e.g. aliexpress.com/item/1005004046566803.html (LR ear)
Additional parts required for 1084 (MONO) version:
3x 5K6 1/4W resistors
1x 22K 1/4W resistor
NOTE: Some jumper links and parts might already be installed, if that is the case and they are the correct value you can skip to the next step.
1. Install 390R resistor at R210 (behind scart connector)
2. Install 1K resistor at R220 (behind scart connector)
3. Install jumper links at 9270, 9274 and 9275 (behind scart connector)
4. Install 390R resistor at R504 (behind RCA jacks) -OR- if R504 does not exist, install jumper link at 9206 (behind RCA jacks)
5. Remove jumper links at 9289 (behind scart connector) and 9290 (towards middle of board) if installed
6. Install 1N4148 diode at 9290, with the band facing towards front of monitor
6N. NTSC ONLY: If R232 (mid-left of board) is in the "NTSC" position, move it to the "PAL" position. If your board does not have these labels you can ignore this step
---
STEREO ONLY:
7S. Remove right channel audio and ground wires from scart footprint - required to install the scart connector
8S. Solder the right channel audio wire to the existing wire at ▲91, and audio ground wire to the existing wire at ▲78 (both are behind the scart connector - remove the audio amplifer board for better access)
9S. Install scart connector
---
MONO ONLY:
7M. Install 5K6 resistors at R305, R306 (behind scart connector), and R307 (behind RCA jacks)
8M. Install 22K resistor at R303 (behind scart connector)
9M. Install scart connector
---
OPTIONAL MOD to enable fast blanking override using VCR switch:
Parts required:
1x 10K 1/4W resistor
1x 1N4148 Diode (or equiv)
1x small length of wire
1x 2.4V Zener diode*
1x 1K5 1/4W resistor*
*these may already be installed - see steps 1 and 2 for details
1. Double check R575 (towards middle of board) is a 1K5 resistor (brown, green, red, gold). Otherwise remove R575 and install a 1K5 resistor
2. Double check D576 is a 2V4 Zener diode. If a resistor is there, remove and install a 2V4 Zener with band towards rear of monitor
3. Solder a 10K resistor and 1N4148 diode in series with diode band facing away from resistor
4. Connect 10K resistor to middle pin of SK5 (VCR switch)
5. Solder a length of wire from the 1N4148 diode (band side) and connect it to jumper link 9290 on the side towards the front of the monitor
** Make sure to properly insulate the resistor and diode with heat shrink so it doesn't short to anything on the board and route the wire and components away from the high voltage area of the PCB (flyback area).
* To use SCART for composite, SCART pin 16 must be 0V, front switch set to CVBS, and (if you did the fast blanking mod) VCR switch off
* To use SCART for RGB without fast blanking (SCART pin 16=0V), front switch must be set to CVBS and VCR switch on (requires fast blanking mod)
* To use SCART for RGB with fast blanking (SCART pin 16=1.5-3V), front switch must be set to CVBS (VCR switch doesn't matter)
* To use DIN jacks with H+V or C-sync, set the front switch to RGB and VCR switch off (if you did the fast blanking mod)
* To use DIN jacks with composite for sync, set the front switch to CVBS, VCR switch on (requires fast blanking mod) and input composite to scart pin 20 or composite jack
----------
🎞
0:00 Intro
5:45 Removing the old mod
7:18 Installing the new mod
15:49 Testing the new mod
17:51 The fastblanking override mod
24:33 Testing fastblanking override
🎞
Thanks for watching!

![Building a cheap 8 4:3 LCD monitor with RF, composite, VGA and HDMI inputs
🛍️ Lectronz store: https://lectronz.com/stores/theretrochannel
. This episode is sponsored by PCBWay https://www.pcbway.com
New PCBWay users can also get $5.00 off their first order using this referral link: https://pcbway.com/g/ab52aW
🛠 Tools and kit: https://www.patreon.com/posts/tools-and-kit-77570017
💬 Discord: https://discord.gg/393FYaM6gM
😎 Ad-free, early access: https://www.patreon.com/theretrochannel
🔗
LCD V29 driver board*: https://s.click.aliexpress.com/e/_DEDk8ph
LCD panel HJ080IA*: https://s.click.aliexpress.com/e/_De4WsQ7
DF14 to FPC cable and converter: https://www.aliexpress.com/item/4001059160872.html
Keypad and remote receiver*: (Select option B for New 3663 8503): https://s.click.aliexpress.com/e/_DkVeto7
[optional] Speakers* (Select option A 37x18mm): https://s.click.aliexpress.com/e/_DlGOxIf
[optional] Acrylic case: https://www.aliexpress.us/item/1005001365597427.html
[optional] USB to DC barrel 5.5x2.1mm*: https://s.click.aliexpress.com/e/_DCcJqFN
If you decide to use the USB to DC cable then you will need a USB power supply capable of delivering at least 1A. Otherwise you will need to find a DC power supply (centre postitive) that can deliver at least 5W, eg. 5V/1A, 9V/600mA,12V/450mA
*AFFILIATE LINK: Affiliate links do not cost you any extra, but I do receive a tiny commission which helps keep the lights on
🔗
🎞
0:00 Intro
0:50 The alternatives
3:21 Power and input options
5:11 240P and lag
5:58 Audio and RF
7:13 Service menu and overscan
8:21 VGA and HDMI
12:05 Building it
16:43 Outro
🎞
Thanks for watching! Building a cheap 8 4:3 LCD monitor with RF, composite, VGA and HDMI inputs](https://i.ytimg.com/vi/s79qBlwpZFQ/mqdefault.jpg)








