Uploaded October 2026 | Updated November 2026, 3 hours ago
Carbon monoxide and unburned gas are two very different dangers, and every tech working on combustion appliances needs to know how to catch both. In this training session, we walk service techs through the safety habits that keep customers safe on gas furnace and water heater calls, from reading a low-level CO monitor to responding when a customer says they smell gas.
Carbon monoxide comes from incomplete combustion. You can’t see it or smell it, and even low levels over time can harm children, older adults, and people with respiratory conditions. That’s why a low-level CO monitor with a display should be on you whenever you work on combustion equipment. Glance at it while the system runs, and make sure the reading stays at 0 or 1 and isn’t climbing. We also explain why standard household CO alarms stay quiet until levels are much higher, and why we recommend a low-level monitor for any home with combustion appliances.
Gas leaks are a separate hazard. Unburned gas that builds up can lead to fire or an explosion. When a customer smells gas, don’t just shrug and leave. Use a combustible gas leak detector and check every combustion appliance in the house. The same care applies to testing and adjusting gas pressure, because a test port left open on the gas valve is a leak you created yourself.
Finally, we cover the visual checks that prevent most combustion problems: watching the burner flame for a mostly blue flame running straight down the burners, spotting orange flame or flame rollout from burner misalignment, finding disconnected flues, and recognizing a furnace closed into a closet without enough combustion air.
In this video:
Carbon monoxide vs. gas leaks and why they’re different dangers
Why techs need a low-level CO monitor with a display
What reading to expect and when to worry
Why household CO alarms don’t sound at low levels
Using a combustible gas leak detector when a customer smells gas
Gas pressure testing and not leaving test ports open
Burner flame checks, flue inspection, and combustion air
Take gas seriously, carry the right tools, and use your eyes. Those habits prevent nearly every carbon monoxide and gas leak problem in the field.
More videos on measuring and adjusting gas pressure:
youtube.com/watch?v=d1L6Ut2pIYI
youtube.com/watch?v=xgZQmaE4HFA&t=616s
---
NEXT VIDEO
Adjusting Gas Pressure on a Standard and Gemini Furnace Valve
youtube.com/watch?v=d1L6Ut2pIYI
KEEP LEARNING
Start here:
hvacrschool.com/start
Free HVAC/R training, tech tips, quizzes, calculators, courses, and more:
hvacrschool.com
Listen to the HVAC School podcast:
hvacrschool.com/podcast
Get the HVAC School app:
hvacrschool.com/apps-page
HVAC School provides free HVAC/R training—primarily for techs, by techs. The goal is not just to collect facts. It is to understand the system well enough to apply what you know in the field.
Questions or corrections? Leave a comment and include the equipment model, measurements, and source when you can. None of us gets everything right, and good measurements beat confident guesses.
This content is educational. Follow manufacturer instructions, use proper PPE and safe work practices, and comply with the codes and standards that apply to your equipment and jurisdiction.
Carbon monoxide and unburned gas are two very different dangers, and every tech working on combustion appliances needs to know how to catch both. In this training session, we walk service techs through the safety habits that keep customers safe on gas furnace and water heater calls, from reading a low-level CO monitor to responding when a customer says they smell gas.
Carbon monoxide comes from incomplete combustion. You can’t see it or smell it, and even low levels over time can harm children, older adults, and people with respiratory conditions. That’s why a low-level CO monitor with a display should be on you whenever you work on combustion equipment. Glance at it while the system runs, and make sure the reading stays at 0 or 1 and isn’t climbing. We also explain why standard household CO alarms stay quiet until levels are much higher, and why we recommend a low-level monitor for any home with combustion appliances.
Gas leaks are a separate hazard. Unburned gas that builds up can lead to fire or an explosion. When a customer smells gas, don’t just shrug and leave. Use a combustible gas leak detector and check every combustion appliance in the house. The same care applies to testing and adjusting gas pressure, because a test port left open on the gas valve is a leak you created yourself.
Finally, we cover the visual checks that prevent most combustion problems: watching the burner flame for a mostly blue flame running straight down the burners, spotting orange flame or flame rollout from burner misalignment, finding disconnected flues, and recognizing a furnace closed into a closet without enough combustion air.
In this video:
Carbon monoxide vs. gas leaks and why they’re different dangers
Why techs need a low-level CO monitor with a display
What reading to expect and when to worry
Why household CO alarms don’t sound at low levels
Using a combustible gas leak detector when a customer smells gas
Gas pressure testing and not leaving test ports open
Burner flame checks, flue inspection, and combustion air
Take gas seriously, carry the right tools, and use your eyes. Those habits prevent nearly every carbon monoxide and gas leak problem in the field.
More videos on measuring and adjusting gas pressure:
youtube.com/watch?v=d1L6Ut2pIYI
youtube.com/watch?v=xgZQmaE4HFA&t=616s
---
NEXT VIDEO
Adjusting Gas Pressure on a Standard and Gemini Furnace Valve
youtube.com/watch?v=d1L6Ut2pIYI
KEEP LEARNING
Start here:
hvacrschool.com/start
Free HVAC/R training, tech tips, quizzes, calculators, courses, and more:
hvacrschool.com
Listen to the HVAC School podcast:
hvacrschool.com/podcast
Get the HVAC School app:
hvacrschool.com/apps-page
HVAC School provides free HVAC/R training—primarily for techs, by techs. The goal is not just to collect facts. It is to understand the system well enough to apply what you know in the field.
Questions or corrections? Leave a comment and include the equipment model, measurements, and source when you can. None of us gets everything right, and good measurements beat confident guesses.
This content is educational. Follow manufacturer instructions, use proper PPE and safe work practices, and comply with the codes and standards that apply to your equipment and jurisdiction.










