Uploaded September 2015 | Updated September 2026, 2 weeks ago
Learn how to make a frame for your canvas! Build your own picture frame to save a ton of money.
The photo for the canvas was taken by Brandon Ostermiller of Bozeman, Montana. Email him for inquires at bostermiller74@gmail.com
For more info, project photos, and downloadable plans check out:
diypete.com/CanvasFrames
Plans: gumroad.com/l/canvasframes
Clean the Barnwood and Cut to Size
We’ll start this project by making sure the barnwood is completely free of any nails, screws, dirt, and debris. You can either use some sandpaper to clean it off, a hand-held brush, or scraper. Be sure not to sand too much (just get any surface dirt, etc off). We want to leave the wood distressed and aged, it adds to the look. Then with your table saw or circular saw, measure and mark out your cuts. Refer to the downloadable plans for a complete cut list.
Need tool recommendations or curious about the tools I trust and use in my builds? Visit my Amazon Store to find everything I recommend for DIY projects big and small! amazon.com/shop/petesveen?ref_=cm_sw_r_cp_ud_aipsfshop_2HRAJ4RJR0J89C2ST1F4
Cut the Lengths and Angles on the Miter Saw
Once we have all of the boards ripped down to the right thickness and width, we’ll head over to the miter saw to make the length and angle cuts. You may want to make the cuts generous (not exact dimensions at first) to ensure you’ve left enough for the 45 degree mitered corners. Measure twice and cut once! All of the corners are mitered together, so cut them all to 45 degree angles that will come together to form 90 degree corners. For the lengths, refer to the downloadable plans here or measure your custom canvas print’s length.
Assemble the Main Frame
Start with one corner, true it up, glue it up, and screw it together. You want to make sure to add wood glue to these miter joints, pre drill any spots where screws are going to go, and use clamps if need be. After you’ve built one miter corner, bring it to the canvas frame and attach it using screws (pre-drill these holes too). Directly drill from the canvas interior frame into your barnwood frame. Repeat these steps for each of the four mitered corners.
Attach the Outer Frame
Now we add the outer section of the frame that adds depth and dimension to the overall look. If, when ripping your barnwood boards, you exposed sections of wood that don’t match the barnwood look, then either wood burn them, use a steel wool and vinegar solution, or other aging method now. Apply wood glue to the lengths of every section that will be taking these outer frame pieces. Align it all and use your nailgun or hammer and nails to attach to the main frame.
Install and Enjoy
Almost done, we just need to install it! You’ll want to screw this canvas photo with barnwood frame directly into studs (the size and weight of ours needed direct stud install). Screw it into place and step back and admire! This is a great project that doesn’t take long and is fun to collaborate on. Post your barnwood frame pieces below!
----
Looking for more DIY videos? Be sure to check out our channel and subscribe for updates!
Looking for woodworking, concrete working, and other DIY projects plans to follow? You can download plans for free at gumroad.com/DIYPETE and premium plans at: diypete.com/diy-project-plans
Facebook: facebook.com/DiyProjectsWithPete
Instagram: instagram.com/diypete
Pete Sveen
1627 W Main Street Suite 182
Bozeman, Montana 59715
#diyframe #diywoodprojects #artframe
Learn how to make a frame for your canvas! Build your own picture frame to save a ton of money.
The photo for the canvas was taken by Brandon Ostermiller of Bozeman, Montana. Email him for inquires at bostermiller74@gmail.com
For more info, project photos, and downloadable plans check out:
diypete.com/CanvasFrames
Plans: gumroad.com/l/canvasframes
Clean the Barnwood and Cut to Size
We’ll start this project by making sure the barnwood is completely free of any nails, screws, dirt, and debris. You can either use some sandpaper to clean it off, a hand-held brush, or scraper. Be sure not to sand too much (just get any surface dirt, etc off). We want to leave the wood distressed and aged, it adds to the look. Then with your table saw or circular saw, measure and mark out your cuts. Refer to the downloadable plans for a complete cut list.
Need tool recommendations or curious about the tools I trust and use in my builds? Visit my Amazon Store to find everything I recommend for DIY projects big and small! amazon.com/shop/petesveen?ref_=cm_sw_r_cp_ud_aipsfshop_2HRAJ4RJR0J89C2ST1F4
Cut the Lengths and Angles on the Miter Saw
Once we have all of the boards ripped down to the right thickness and width, we’ll head over to the miter saw to make the length and angle cuts. You may want to make the cuts generous (not exact dimensions at first) to ensure you’ve left enough for the 45 degree mitered corners. Measure twice and cut once! All of the corners are mitered together, so cut them all to 45 degree angles that will come together to form 90 degree corners. For the lengths, refer to the downloadable plans here or measure your custom canvas print’s length.
Assemble the Main Frame
Start with one corner, true it up, glue it up, and screw it together. You want to make sure to add wood glue to these miter joints, pre drill any spots where screws are going to go, and use clamps if need be. After you’ve built one miter corner, bring it to the canvas frame and attach it using screws (pre-drill these holes too). Directly drill from the canvas interior frame into your barnwood frame. Repeat these steps for each of the four mitered corners.
Attach the Outer Frame
Now we add the outer section of the frame that adds depth and dimension to the overall look. If, when ripping your barnwood boards, you exposed sections of wood that don’t match the barnwood look, then either wood burn them, use a steel wool and vinegar solution, or other aging method now. Apply wood glue to the lengths of every section that will be taking these outer frame pieces. Align it all and use your nailgun or hammer and nails to attach to the main frame.
Install and Enjoy
Almost done, we just need to install it! You’ll want to screw this canvas photo with barnwood frame directly into studs (the size and weight of ours needed direct stud install). Screw it into place and step back and admire! This is a great project that doesn’t take long and is fun to collaborate on. Post your barnwood frame pieces below!
----
Looking for more DIY videos? Be sure to check out our channel and subscribe for updates!
Looking for woodworking, concrete working, and other DIY projects plans to follow? You can download plans for free at gumroad.com/DIYPETE and premium plans at: diypete.com/diy-project-plans
Facebook: facebook.com/DiyProjectsWithPete
Instagram: instagram.com/diypete
Pete Sveen
1627 W Main Street Suite 182
Bozeman, Montana 59715
#diyframe #diywoodprojects #artframe
