Uploaded October 2026 | Updated November 2026, 3 hours ago
In this video, I’m building a custom hot wire foam carving tool designed to cut decorative profiles into EPS foam without the huge mess created by a router.
For years I’ve used a palm router to add decorative edges and molding details to Halloween tombstones and cemetery monuments, but the cleanup is brutal. So I wanted to see if I could make a simple homemade hot wire cutter using nichrome wire, a small power supply, and a few scraps from around the shop.
I’ll show you how I bend custom hot wire profiles, mount them to a simple wooden guide, and use them to carve repeatable decorative shapes into foam. I’ll also test the tool on both EPS and XPS foam to see how well it performs compared with a traditional router.
Along the way, I’ll cover:
• Using nichrome wire as a custom heating element
• Creating repeatable decorative foam profiles
• Building a simple guide for consistent cuts
• Cutting EPS vs. XPS foam
• Using the offcuts as additional trim details
• Where this method works well — and where it still needs improvement
This isn’t a replacement for every foam-carving tool, but for adding decorative details to Halloween tombstones, cemetery props, columns, monuments, and other foam builds, it has a lot of potential — and it creates a whole lot less mess.
⚠️ Hot wire tools involve electricity, heat, and foam fumes. Use proper ventilation, respiratory protection, and appropriate electrical safety precautions whenever working with heated foam.
If you enjoy Halloween prop making, foam carving, cemetery builds, scenic fabrication, and DIY special effects, be sure to subscribe for more projects.
#FoamCarving #HotWireCutter #HalloweenDIY
WAYS TO SUPPORT MY CHANNEL
---------------------------------------------------------
Patreon - patreon.com/vanoaksprops
Official Merch & 3D Models - shop.vanoaksprops.com
Affiliate Links - vanoaksprops.com/affiliate-links
MATERIALS:
(please note: Sellers may change the products sold via these links without notice)
----------------------
18 gauge nichromium wire - https://link.amazon/B03vvsB7k
6v 3a Power Supply - https://link.amazon/B0bC2nFXz
Alligator Clip - https://link.amazon/B00kNYAI3
Gorilla Glue - https://link.amazon/B08jkVIg1
INSTAGRAM: @vanoaksprops
DISCLAIMER: Links included in this description may be affiliate links. I may receive a commission if you purchase a product or service via the links provided above. There is no additional charge to you; it helps support this channel!
#VanOaksProps
In this video, I’m building a custom hot wire foam carving tool designed to cut decorative profiles into EPS foam without the huge mess created by a router.
For years I’ve used a palm router to add decorative edges and molding details to Halloween tombstones and cemetery monuments, but the cleanup is brutal. So I wanted to see if I could make a simple homemade hot wire cutter using nichrome wire, a small power supply, and a few scraps from around the shop.
I’ll show you how I bend custom hot wire profiles, mount them to a simple wooden guide, and use them to carve repeatable decorative shapes into foam. I’ll also test the tool on both EPS and XPS foam to see how well it performs compared with a traditional router.
Along the way, I’ll cover:
• Using nichrome wire as a custom heating element
• Creating repeatable decorative foam profiles
• Building a simple guide for consistent cuts
• Cutting EPS vs. XPS foam
• Using the offcuts as additional trim details
• Where this method works well — and where it still needs improvement
This isn’t a replacement for every foam-carving tool, but for adding decorative details to Halloween tombstones, cemetery props, columns, monuments, and other foam builds, it has a lot of potential — and it creates a whole lot less mess.
⚠️ Hot wire tools involve electricity, heat, and foam fumes. Use proper ventilation, respiratory protection, and appropriate electrical safety precautions whenever working with heated foam.
If you enjoy Halloween prop making, foam carving, cemetery builds, scenic fabrication, and DIY special effects, be sure to subscribe for more projects.
#FoamCarving #HotWireCutter #HalloweenDIY
WAYS TO SUPPORT MY CHANNEL
---------------------------------------------------------
Patreon - patreon.com/vanoaksprops
Official Merch & 3D Models - shop.vanoaksprops.com
Affiliate Links - vanoaksprops.com/affiliate-links
MATERIALS:
(please note: Sellers may change the products sold via these links without notice)
----------------------
18 gauge nichromium wire - https://link.amazon/B03vvsB7k
6v 3a Power Supply - https://link.amazon/B0bC2nFXz
Alligator Clip - https://link.amazon/B00kNYAI3
Gorilla Glue - https://link.amazon/B08jkVIg1
INSTAGRAM: @vanoaksprops
DISCLAIMER: Links included in this description may be affiliate links. I may receive a commission if you purchase a product or service via the links provided above. There is no additional charge to you; it helps support this channel!
#VanOaksProps










