Uploaded March 2026 | Updated November 2026, 4 days ago
Modified a BC250 to be able to control a standard ATX supply and run off the standby rail.
You need to remove an inductor and solder a wire to one of its pads, and solder two other wires to the board.
I used the standard ATX colour scheme for the three wires on the board:
Violet: 5V standby
Green: PSON
Grey: Power Good
Realistically you do not need the third wire, as the BC250 is wired to *assume* power good if left floating. However, since it's easy enough to connect, I figured I'd use it. It controls a mosfet that enables the 12V standby rail, which is connected to a second mosfet that enables the main 12V rail when powered on.
I traced the control signal for the second mosfet, and it *just* happens to be the same logic as an ATX PSU (pullup to 5V standby, connected to ground to turn on the supply), so we can connect to it and use it to wake and sleep the PSU.
The 5V standby rail is *usually* derived from the 12V standby rail, and seemingly nothing else comes from that rail when in standby.
By removing the inductor, we knock out the 5V standby rail which allows us to feed our own 5V standby instead into the board. This keeps the USB ports active as well as the chipset and I/O controller, just as the board normally would.
However, as soon as the board requests the main rails to come online, it also wakes the ATX supply, and the BC250 is none the wiser.
The standby rail needs to have enough current to run the USB ports when off, plus 600mA for the board itself. It's not a particularly efficient board when off, but it wasn't really designed to be shut down.
The BC250 re-routes USB power to its main 5V rail when on, so the standby rail does NOT need to run the ports while in operation, but there's still about a 500mA load from the rails it does run.
I have not fully tested this system yet, hence the temporary connections to things. I would appreciate it if other brave souls would like to try this on their systems.
I've also got a dell server PSU on the way with a 12V standby rail instead of 5V, and I believe the BC250 can be re-wired to run from that too.
Modified a BC250 to be able to control a standard ATX supply and run off the standby rail.
You need to remove an inductor and solder a wire to one of its pads, and solder two other wires to the board.
I used the standard ATX colour scheme for the three wires on the board:
Violet: 5V standby
Green: PSON
Grey: Power Good
Realistically you do not need the third wire, as the BC250 is wired to *assume* power good if left floating. However, since it's easy enough to connect, I figured I'd use it. It controls a mosfet that enables the 12V standby rail, which is connected to a second mosfet that enables the main 12V rail when powered on.
I traced the control signal for the second mosfet, and it *just* happens to be the same logic as an ATX PSU (pullup to 5V standby, connected to ground to turn on the supply), so we can connect to it and use it to wake and sleep the PSU.
The 5V standby rail is *usually* derived from the 12V standby rail, and seemingly nothing else comes from that rail when in standby.
By removing the inductor, we knock out the 5V standby rail which allows us to feed our own 5V standby instead into the board. This keeps the USB ports active as well as the chipset and I/O controller, just as the board normally would.
However, as soon as the board requests the main rails to come online, it also wakes the ATX supply, and the BC250 is none the wiser.
The standby rail needs to have enough current to run the USB ports when off, plus 600mA for the board itself. It's not a particularly efficient board when off, but it wasn't really designed to be shut down.
The BC250 re-routes USB power to its main 5V rail when on, so the standby rail does NOT need to run the ports while in operation, but there's still about a 500mA load from the rails it does run.
I have not fully tested this system yet, hence the temporary connections to things. I would appreciate it if other brave souls would like to try this on their systems.
I've also got a dell server PSU on the way with a 12V standby rail instead of 5V, and I believe the BC250 can be re-wired to run from that too.







![My Secrets Revealed! Android TV In 4:3 On A CRT!
TUTORIAL:
(Please pardon the rushed video, I was tired and needed to get to sleep)
You will need:
Android TV box (I used the Onn 4K box for 20$, dont get the 1080p one for 15, its way slower)
An HDMI to VGA converter with audio (I prefer these slimline ones that screw directly to the VGA input port)
3.5mm to RCA cable
The generic Silver Box VGA to Composite+S-Video converter with the six buttons on the side
A computer with ADB set up
Initial setup:
Set up your android TV box as normal on a modern TV. Set the resolution to 1080p60. Set the font size to large.
Install Projectivy through the google app store, enable its permissions and accessibility features, then dig through the projectivy settings and enable Override Current Launcher to set it as the default home launcher. We need to do this for the sole reason that the stock home screen launcher doesnt support 4:3 resolutions.
Setup on CRT:
Chain those converters! Android box to HDMI adapter, HDMI adapter to silver VGA converter, then finally either s-video or composite video from the silver box to your TV. If your TV has s-video, you will get a considerably cleaner picture. Connect the 3.5mm to RCA adapter from the HDMI adapter to the audio inputs on your TV. If your TV only has an antenna jack, youll need to purchase an RF modulator to convert the video and audio signals to RF. This will allow you to use this setup even on an ancient vacuum tube set.
Turn everything on, and youll possibly notice the image rolling with no colour, or just a completely incoherent image. THIS IS EXPECTED! The silver box defaults to PAL video, you will need to blindly navigate the menu to change to your regions video standard, likely NTSC. Press menu, then press down 7 times, then press left or right until the picture comes in properly.
You should now see your android TV box on your CRT, but the image will be squished horizontally. Were almost done!
Enable developer options (click the build number in the about tab a bunch of times) and enable wireless debugging. Your android TV box will offer you an IP address, which youll need to connect to in ADB. If you cant read the IP address, press the zoom button on the silver box to zoom into the picture. Connect to the tv box using the following command:
adb connect [IP address goes here]:5555
Finally, send another command:
adb shell wm size 1600:1200
Congrats, your android box is now internally running all its applications in 4:3! However, the android TV box is still outputting a 16:9 signal, just with black bars on the sides.
Heres where the brilliance of this magic silver box comes in. Use the Hsize and Vsize adjustments in the menu to scale the android boxs picture to just barely fill your CRT. When outside of the silver boxs menu, the arrow keys will move the image around to center it. This magical feature is what allows us to fit a 16:9 video signal on a 4:3 TV. Additionally, if you plug in a modern HDMI source like a Nintendo Switch 2, you can fill the screen horizontally and compress it vertically, effectively letterboxing the 16:9 signal to properly display on a 4:3 set.
The streaming box will stay like this after reboots, but NOT a factory reset. Changing the resolution from 1080p to 720p will reset the 4:3 mode, and youll have to run the ADB commands again. I was also able to set up the streaming boxs remote, so I can turn the TV on and off with the remote as well as adjust the volume.
Apps tested:
Youtube (menus run in 16:9 letterbox, as do 16:9 videos, but 4:3 videos and the player UI will fill the screen)
Youtube music: Music player runs fullscreen 4:3
Please post below what apps youve tried! I dont have any streaming services to test.
Sanitized, non-affiliated non-tracking links provided below, feel free to shop around as many ebay sellers will jack the prices when they see an influx of buyers:
VGA to composite/svideo: https://www.ebay.com/itm/365930535871
HDMI to VGA with audio: https://www.ebay.com/itm/146465263477
3.5mm to RCA (generic): https://www.ebay.com/itm/122381829519
Android TV box: https://www.walmart.com/ip/onn-Google-TV-4K-Streaming-Box-New-2023-4K-UHD-Resolution/2835618394 My Secrets Revealed! Android TV In 4:3 On A CRT!](https://i.ytimg.com/vi/lr69laGFXzE/mqdefault.jpg)


