Uploaded September 2025 | Updated November 2026, 3 days ago
Kindly sponsored by https://www.PCBWay.com: PCB manufacture, CNC machining, sheet metal fabrication, 3D printing and injection moulding.
This is part three in the series where I try to resurrect an Atari Falcon030 motherboard which has had some damage from an accelerator removal. It had no CPU, quite a few mangled pads and some dodgy precepitate over parts of the board.
At the end of part two we were able to get the diagnostic cartridge to run and we found a nasty short under a chip that services the DSP. This time out we'll be focusing on trying to get the OS to boot and see if we can bring the DSP to life.
Will it be happy ending?
DFB1 as featured in this series: github.com/dh219/DFB
IDE Autoswap adapter: github.com/dh219/IDE_Adapter_Autoswap / pcbway.com/project/shareproject/Atari_Falcon_Auto_Byte_Swapping_IDE_Adapter_4a5c9bda.html
https://thetechnoshed.bsky.social
github.com/dh219
YouTube.com/@thetechnoshed
~~~
Check out PCBWay's community of makers here: pcbway.com/project
My PCBWay Projects page: pcbway.com/project/member/?bmbno=2C89C44C-EDF4-43
Kindly sponsored by https://www.PCBWay.com: PCB manufacture, CNC machining, sheet metal fabrication, 3D printing and injection moulding.
This is part three in the series where I try to resurrect an Atari Falcon030 motherboard which has had some damage from an accelerator removal. It had no CPU, quite a few mangled pads and some dodgy precepitate over parts of the board.
At the end of part two we were able to get the diagnostic cartridge to run and we found a nasty short under a chip that services the DSP. This time out we'll be focusing on trying to get the OS to boot and see if we can bring the DSP to life.
Will it be happy ending?
DFB1 as featured in this series: github.com/dh219/DFB
IDE Autoswap adapter: github.com/dh219/IDE_Adapter_Autoswap / pcbway.com/project/shareproject/Atari_Falcon_Auto_Byte_Swapping_IDE_Adapter_4a5c9bda.html
https://thetechnoshed.bsky.social
github.com/dh219
YouTube.com/@thetechnoshed
~~~
Check out PCBWay's community of makers here: pcbway.com/project
My PCBWay Projects page: pcbway.com/project/member/?bmbno=2C89C44C-EDF4-43


![PiStormSTE: a new PiStorm board that fits inside the STE
Kindly sponsored by PCBWay.com
PiStorm has come on leaps and bounds since I was last actively developing for the project. A new ST-specific repository has been set up by Cryptodad (on the Discord) and a lot of new work has gone in.
Weve got accelerated high-resolution, high-colour HDMI graphics, virtual hard discs, real-time clock pass-throughs and the biggest breakthrough of all, 100% ST-RAM access speeds at long last on the Pi 3+ (these have been available for a while on the Pi 4).
There are maybe some tweaks needed to firmware still, but this is getting very close to a viable daily driver.
BUT, open case machines, specialist motherboards, or relocator gymnastics have been required to use the two or three board stack.
So I thought Id do something about it. In this video I build a special STE-targetted version of the PiStorm hardware which allows a Pi3A+ or a modified (ethernet socket removed) Pi 4 to be fitted internally to the Atari STE.
Do have a look and join the PiStorm Discord if youd like in on project.
Made in KiCAD. Open source, as normal.
This project can be ordered from my PCBWay community page: https://www.pcbway.com/project/shareproject/PiStorm_STE_v1_0_df288de0.html
[[ Please note, I have specified latches rather than flipflops in this BOM as the lead time is much shorter. Through-hole components (1.27mm pin headers and 2.54mm receptacle) will need to be sourced separately and fitted yourself. ]]
PiStorm original (Amiga): https://github.com/captain-amygdala/pistorm
PiStorm-Atari (firmware & software for the Pi): https://github.com/gotaproblem/pistorm-atari
PiStormSTE (now under the PiStorm Atari repository): https://github.com/gotaproblem/pistorm-atari/tree/main/hardware/pistorm-ste
PiStorm Discord: https://discord.com/invite/j6rPtzxaNW
BBAN Solutions ST disc images: https://bbansolutions.co.uk/index.php/reviving-the-past/pistorm-atari/
~~~
PCBWay offer PCB manufacture, CNC machining, sheet metal fabrication, 3D printing and injection moulding.
Check out their community of makers here: https://www.pcbway.com/project/
~~~ PiStormSTE: a new PiStorm board that fits inside the STE](https://i.ytimg.com/vi/xtQSo7G3DBo/mqdefault.jpg)



