Uploaded November 2026 | Updated November 2026, 3 days ago
Arduino Bughopper is a USB to UART add-on for serial debugging of Arduino Uno Q or Ventuno Q. In this video, I take a look at Arduino Bughopper and demonstrate how it can be used to access the serial console of the new Arduino UNO Q. Arduino UNO Q is far more than a the good old Arduino Uno board. It combines a microcontroller with a Qualcomm QRB2210 microprocessor (MPU) capable of running a full Linux distribution. Out of the box it comes with Debian. Using Arduino Bughopper and a USB-C connection, I establish serial communication between my Ubuntu laptop and the Arduino UNO Q. I then open a terminal using the screen command at 115200 baud, log in to the Debian Linux system, and run a few basic commands to inspect the Linux kernel and Debian versions. Serial console access is particularly useful for embedded Linux development, troubleshooting boot issues, and debugging low-level software such as the U-Boot bootloader and the Linux kernel. It can also be invaluable when building custom Linux distributions with the Yocto Project. This video is a quick hands-on demonstration of Arduino Bughopper as a useful tool for engineers and embedded Linux developers.
For the serial communication demo I executed in the terminal of Ubuntu:
sudo screen /dev/ttyUSB0 115200
๐ฅ Related videos
===
Arduino Uno Q Is Wild: One Board Combines Debian Linux on Qualcomm SoC and Zephyr RTOS on STM32
youtu.be/pZjUHeTQoKE?si=ePZ0ibxqr6DFd9Zq
๐ Chapters
===
0:00 Intro
0:24 Unboxing
1:51 Demo
4:02 Conclusions
Arduino Bughopper is a USB to UART add-on for serial debugging of Arduino Uno Q or Ventuno Q. In this video, I take a look at Arduino Bughopper and demonstrate how it can be used to access the serial console of the new Arduino UNO Q. Arduino UNO Q is far more than a the good old Arduino Uno board. It combines a microcontroller with a Qualcomm QRB2210 microprocessor (MPU) capable of running a full Linux distribution. Out of the box it comes with Debian. Using Arduino Bughopper and a USB-C connection, I establish serial communication between my Ubuntu laptop and the Arduino UNO Q. I then open a terminal using the screen command at 115200 baud, log in to the Debian Linux system, and run a few basic commands to inspect the Linux kernel and Debian versions. Serial console access is particularly useful for embedded Linux development, troubleshooting boot issues, and debugging low-level software such as the U-Boot bootloader and the Linux kernel. It can also be invaluable when building custom Linux distributions with the Yocto Project. This video is a quick hands-on demonstration of Arduino Bughopper as a useful tool for engineers and embedded Linux developers.
For the serial communication demo I executed in the terminal of Ubuntu:
sudo screen /dev/ttyUSB0 115200
๐ฅ Related videos
===
Arduino Uno Q Is Wild: One Board Combines Debian Linux on Qualcomm SoC and Zephyr RTOS on STM32
youtu.be/pZjUHeTQoKE?si=ePZ0ibxqr6DFd9Zq
๐ Chapters
===
0:00 Intro
0:24 Unboxing
1:51 Demo
4:02 Conclusions
![The Yocto Project on Raspberry Pi 5 Episode 8: Using ConnMan Network Manager for Wi-Fi Connectivity
ConnMan is an open-source, command-line network manager designed for embedded Linux devices with a focus on fast connection handling and resolution times. First released in 2008, it is written in C, licensed under the GNU GPL, and its source code is hosted in a Git repository on kernel.org.
๐ก Using ConnMan
- Bring up the Wi-Fi interface wlan0
rfkill unblock wifi
ip link set wlan0 up
- Enter connman CLI
connmanctl
- Enable Wi-Fi (only if it is not enabled)
technologies
enable wifi
- Scan for W-Fi networks:
scan wifi
- List the found and available Wi-Fi networks (write down the wireless network service with format like wifi_[MAC_ADDR]_[SSID_HEX]_managed_psk:
services
- Turn on agent:
agent on
- Connect to a Wi-Fi network:
connect wifi_[MAC_ADDR]_[SSID_HEX]_managed_psk
- If the network is secured the agent will prompt you to enter a password:
Agent RequestInput wifi_[MAC_ADDR]_[SSID_HEX]_managed_psk
Passphrase = [ Type=psk, Requirement=mandatory ]
Passphrase?
๐ค Troubleshooting
To bring up the WiFi interface automatically at boot on embedded Linux distributions with systemd create file /etc/systemd/network/10-wlan0.network with the following content:
[Match]
Name=wlan0
[Network]
DHCP=yes
๐ Related Videos
Episode 1: Building an Embedded GNU Linux Distribution
https://youtu.be/fY7u6PiV8qA?si=goTZ5V7I2dwa33a-
Episode 2: SSH for Remote Network Access
https://youtu.be/ltckiBV9FXg?si=DJwsKLDhHkDIqCIn
Episode 3: The Yocto Project on Raspberry Pi 5 Episode 3: Running Docker Containers
https://youtu.be/kQnOidK_U3M?si=5KiS1FK87OwfdQ0m
Episode 4: The Yocto Project on Raspberry Pi 5 Episode 4: U-Boot Bootloader
https://youtu.be/9tohomiv1Ug?si=kylUv0uT_BFmXt5g
Episode 5: Modifying U-Boot Environment in Linux with fw_setenv
https://youtu.be/SB5NvIF1IEU?si=0So6Gfv9hQR7gQgY
Episode 6: Runtime Package Management with apt and deb Packages
https://youtu.be/6i5UtF7fiaA?si=8DuUHUxywVEEtdyN
Episode 7: Create a New Layer, a New Recipe (.bb) and .bbappend
https://youtu.be/W5J1W_Cy14Y?si=ftu5WpeGqel8BZhf
๐ Useful Links
https://www.yoctoproject.org/
https://docs.yoctoproject.org/
https://www.openembedded.org/wiki/Main_Page
https://anavi.org/article/325/
๐ Chapters
0:00 Intro
0:25 ConnMan
3:45 connmanctl
8:00 Troubleshooting
11:10 Summary
11:40 Conclusions The Yocto Project on Raspberry Pi 5 Episode 8: Using ConnMan Network Manager for Wi-Fi Connectivity](https://i.ytimg.com/vi/ib8a0PeOGAU/mqdefault.jpg)









