Uploaded December 2020 | Updated September 2026, 2 weeks ago
The ANET ET4 and ANET ET5 get mixed reviews. I believe some of the problems people have with these printers are caused by improper installation and setup. This is not the user's fault as properly setting up the print bed is a bit tricky. In the review of the ANET ET5, I go through the steps necessary to properly use these printers and how they have the potential to become outstanding 3d printers at a very attractive price.
00:00 Introduction
04:04 ANET ET54 Overview
10:35 Assembly and Print Quality
16:40 Required Setup Steps
16:45 Mechanical Bed Leveling
20:03 Probe Calibration
24:00 Firmware Assisted Bed Leveling
26:30 Firmware Auto Bed Leveling
29:30 ANET ET4 Review Summary
Let's continue to learn together. Irv
---
The following links are to products I have used, reviewed, or evaluated for the MakeWithTech community. Some of the links below are affiliate links that provide commissions, at no cost to you, and help support the MakeWithTech video production, purchase of products for reviews, lab, forum, and web site.
I have reviewed the following printers or similar printers:
➡︎ kit.co/makewithtech/3d-printers-reviewed-on-drvax-youtube-channel
These are some of the tools I use for 3d printing day-to-day:
➡︎ kit.co/makewithtech/basic-3d-printing-tools
I have reviewed or used the following 3d printer upgrades:
➡︎ kit.co/makewithtech/3d-printer-upgrades
Here are the 3d printer filaments I use to evaluate prints, software, and techniques:
➡︎ kit.co/makewithtech/3d-printing-filament-i-use-at-drvax
I will be covering basic electronics and software in future MakeWithTech segments and here are the products I am using:
➡︎ kit.co/makewithtech/software-and-electronic-kits
Some of the Woodworking products I use:
➡︎ kit.co/makewithtech/drvax-woodworking-tools-and-supplies
---
** Affiliate disclaimer: some of the above links in my videos may be affiliate links, which generate a sales commission for me. Your price is the same or less than if you go to the site directly. These sales commissions help to support the MakeWithTech channel. (https://makewithtech.com)
** MakeWithTech and the MakeWithTech videos are Copyright Cogitations, LLC. (https://cogitations.com)
** Equipment used in the MakeWithTech videos has the potential to cause injury if misused. Use all equipment and tools at your own risk and follow all manufacturer's safety recommendations.
** Cogitations, LLC licenses all music used in the MakeWithTech videos from Epidemic Sound. Cogitations, LLC uses only authorized or open source clip art and third party images. Images and videos used in product reviews and tutorials are from the original product (software or hardware) manufacturer's site.
** We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. .
The ANET ET4 and ANET ET5 get mixed reviews. I believe some of the problems people have with these printers are caused by improper installation and setup. This is not the user's fault as properly setting up the print bed is a bit tricky. In the review of the ANET ET5, I go through the steps necessary to properly use these printers and how they have the potential to become outstanding 3d printers at a very attractive price.
00:00 Introduction
04:04 ANET ET54 Overview
10:35 Assembly and Print Quality
16:40 Required Setup Steps
16:45 Mechanical Bed Leveling
20:03 Probe Calibration
24:00 Firmware Assisted Bed Leveling
26:30 Firmware Auto Bed Leveling
29:30 ANET ET4 Review Summary
Let's continue to learn together. Irv
---
The following links are to products I have used, reviewed, or evaluated for the MakeWithTech community. Some of the links below are affiliate links that provide commissions, at no cost to you, and help support the MakeWithTech video production, purchase of products for reviews, lab, forum, and web site.
I have reviewed the following printers or similar printers:
➡︎ kit.co/makewithtech/3d-printers-reviewed-on-drvax-youtube-channel
These are some of the tools I use for 3d printing day-to-day:
➡︎ kit.co/makewithtech/basic-3d-printing-tools
I have reviewed or used the following 3d printer upgrades:
➡︎ kit.co/makewithtech/3d-printer-upgrades
Here are the 3d printer filaments I use to evaluate prints, software, and techniques:
➡︎ kit.co/makewithtech/3d-printing-filament-i-use-at-drvax
I will be covering basic electronics and software in future MakeWithTech segments and here are the products I am using:
➡︎ kit.co/makewithtech/software-and-electronic-kits
Some of the Woodworking products I use:
➡︎ kit.co/makewithtech/drvax-woodworking-tools-and-supplies
---
** Affiliate disclaimer: some of the above links in my videos may be affiliate links, which generate a sales commission for me. Your price is the same or less than if you go to the site directly. These sales commissions help to support the MakeWithTech channel. (https://makewithtech.com)
** MakeWithTech and the MakeWithTech videos are Copyright Cogitations, LLC. (https://cogitations.com)
** Equipment used in the MakeWithTech videos has the potential to cause injury if misused. Use all equipment and tools at your own risk and follow all manufacturer's safety recommendations.
** Cogitations, LLC licenses all music used in the MakeWithTech videos from Epidemic Sound. Cogitations, LLC uses only authorized or open source clip art and third party images. Images and videos used in product reviews and tutorials are from the original product (software or hardware) manufacturer's site.
** We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. .
