Uploaded January 2026 | Updated November 2026, 3 hours ago
Welcome to this Product Training Module for the Analog Devices ADMX1001 ultra-low noise signal generator and acquisition module. This complete solution delivers DC to 40 kilohertz signals with an impressive negative 130 dBc THD , enabling high quality audio and analog device testing in both lab and production environments.
The ADMX1001 is a compact 40 by 60 millimeter system-on-module with an edge connector for seamless integration into high-density test systems. The design can also be licensed and designed into systems as needed.
The module features an SoC and memory for control. This provides the host SPI interface with a reduced command set for easy control, even with a low-power microcontroller. The SoC controls waveform generation, with enough memory to store up to 16 patterns in non-volatile memory so you can pre-load waveforms and reduce test time. It also performs digital pre-distortion which will be discussed in detail later and this helps achieve the exceptionally low THD signal generation.
The signal generation path features a pair of AD5791 20-bit precision DACs. The high resolution and linearity better than 1 LSB ensure accurate reproduction of signal levels. The outputs of the DACs pass through a high order filter and into a fully differential amplifier to generate the final output, with a 3.5 volt RMS output range and adjustable output common-mode voltage to directly interface with modern ADC inputs.
This design allows one generator to cover nearly all signal needs for test, ac, dc, ramps and random signals such as voice or sound. Additionally, it includes native sinewave, dual-tone, and dc patterns, that users can load without additional configuration.
The acquisition portion of the design can be used for differential or single-ended input with a programmable instrumentation amplifier to adjust the input range and a 24-bit, 256 kilosample per second ADC. When used in combination with the generator, this provides a complete system for spectral and distortion analysis.
The ADMX1001 implements a patented digital pre-distortion, or DPD, algorithm that improves the linearity of the measurement path used to correct source errors. The source generates a single-frequency tone during the measurement phase, acquires the signal through the DPD sense path and reconstructs the waveform in the digital domain, extracts correction parameters, and iterates until it finds the optimal correction.
Without the DPD, the ADMX1001 achieves a typical THD of negative 115 dBc at 1 kilohertz, but adding DPD improves the final output so much that it reduces the typical THD to negative 130 dBc at 1 kilohertz.
For evaluation, the ADMX1001 module plugs into the EVAL-ADMX100X-FMCZ evaluation board, and then this plugs into the SDP-H1 controller board. This setup provides SMA connectors for the source output, either differential or single-ended, the acquisition channel input, and sync inputs.
These modules can be evaluated with the ADMX100X GUI to generate different signals. The PC GUI connects to an SDP controller board via USB that has established SPI communication to the module. This allows users to set the input and output parameters, create waveforms and sequences, and configure measurements to fully evaluate the performance of the ADMX1001 module.
Analog Devices also offers the ADMX1002 module, which offers the same signal generation capabilities without the acquisition function.
The ADMX1001 Ultra-low Distortion Signal Generator Measurement Module with Fully Differential Input Acquisition Channel is suitable for use in R&D labs or ATE for testing high-end audio components, ADCs, and analog sensors or transducers. It can also be used for frequency response measurements and network analysis.
digikey.com/en/products/detail/analog-devices-inc/ADMX1001B/24613261
Maker.io - digikey.com/en/maker
DigiKey’s Blog – TheCircuit digikey.com/en/blog
Connect with DigiKey on Facebook facebook.com/digikey.electronics
And follow us on X https://x.com/digikey
Welcome to this Product Training Module for the Analog Devices ADMX1001 ultra-low noise signal generator and acquisition module. This complete solution delivers DC to 40 kilohertz signals with an impressive negative 130 dBc THD , enabling high quality audio and analog device testing in both lab and production environments.
The ADMX1001 is a compact 40 by 60 millimeter system-on-module with an edge connector for seamless integration into high-density test systems. The design can also be licensed and designed into systems as needed.
The module features an SoC and memory for control. This provides the host SPI interface with a reduced command set for easy control, even with a low-power microcontroller. The SoC controls waveform generation, with enough memory to store up to 16 patterns in non-volatile memory so you can pre-load waveforms and reduce test time. It also performs digital pre-distortion which will be discussed in detail later and this helps achieve the exceptionally low THD signal generation.
The signal generation path features a pair of AD5791 20-bit precision DACs. The high resolution and linearity better than 1 LSB ensure accurate reproduction of signal levels. The outputs of the DACs pass through a high order filter and into a fully differential amplifier to generate the final output, with a 3.5 volt RMS output range and adjustable output common-mode voltage to directly interface with modern ADC inputs.
This design allows one generator to cover nearly all signal needs for test, ac, dc, ramps and random signals such as voice or sound. Additionally, it includes native sinewave, dual-tone, and dc patterns, that users can load without additional configuration.
The acquisition portion of the design can be used for differential or single-ended input with a programmable instrumentation amplifier to adjust the input range and a 24-bit, 256 kilosample per second ADC. When used in combination with the generator, this provides a complete system for spectral and distortion analysis.
The ADMX1001 implements a patented digital pre-distortion, or DPD, algorithm that improves the linearity of the measurement path used to correct source errors. The source generates a single-frequency tone during the measurement phase, acquires the signal through the DPD sense path and reconstructs the waveform in the digital domain, extracts correction parameters, and iterates until it finds the optimal correction.
Without the DPD, the ADMX1001 achieves a typical THD of negative 115 dBc at 1 kilohertz, but adding DPD improves the final output so much that it reduces the typical THD to negative 130 dBc at 1 kilohertz.
For evaluation, the ADMX1001 module plugs into the EVAL-ADMX100X-FMCZ evaluation board, and then this plugs into the SDP-H1 controller board. This setup provides SMA connectors for the source output, either differential or single-ended, the acquisition channel input, and sync inputs.
These modules can be evaluated with the ADMX100X GUI to generate different signals. The PC GUI connects to an SDP controller board via USB that has established SPI communication to the module. This allows users to set the input and output parameters, create waveforms and sequences, and configure measurements to fully evaluate the performance of the ADMX1001 module.
Analog Devices also offers the ADMX1002 module, which offers the same signal generation capabilities without the acquisition function.
The ADMX1001 Ultra-low Distortion Signal Generator Measurement Module with Fully Differential Input Acquisition Channel is suitable for use in R&D labs or ATE for testing high-end audio components, ADCs, and analog sensors or transducers. It can also be used for frequency response measurements and network analysis.
digikey.com/en/products/detail/analog-devices-inc/ADMX1001B/24613261
Maker.io - digikey.com/en/maker
DigiKey’s Blog – TheCircuit digikey.com/en/blog
Connect with DigiKey on Facebook facebook.com/digikey.electronics
And follow us on X https://x.com/digikey










