wayne phillipsWAVETEK SCHLUMBERGER STABILOCK 4031 Repair and Fix Thanks to Paul Kelly G3SDH for the Repair documents and web information. groups.io/g/Wavetek-test-equipment Download service manuals. Do these repairs at your own risk, this video is for information only.
The 4031 RF Attenuator fix can be found on the following link. youtu.be/qgodA0u5mlQ
This is a comprehensive repair, you will need the service manual, for card and component identification. If the Power supply rails , 5v, 15 and -15v are correct check the rear Card 1 10Mhz output is not drifting, if all OK move onto the removable cards, change all the 10uF, 2.2uF, 22uF, 47uF and 100uF SMD capacitors, around 50-70 caps, take your time and check all the tracks after replacing the capacitors. I would suggest trying a few different removal techniques. I also checked all the SMD RF coils/chokes on every Panel. Two were found to be open circuit. UHF SYNTH 213-041 BOARD 461-436 03, REPLACE L3 560nH
To do in circuit tests, you will need Riser/extender cards. Not all the cards have capacitors that need changing but i would recommend a visual inspection for damaged tracks, dry joints etc.
WAVETEK SCHLUMBERGER STABILOCK 4031 Repair and Fixwayne phillips2022-05-17 | WAVETEK SCHLUMBERGER STABILOCK 4031 Repair and Fix Thanks to Paul Kelly G3SDH for the Repair documents and web information. groups.io/g/Wavetek-test-equipment Download service manuals. Do these repairs at your own risk, this video is for information only.
The 4031 RF Attenuator fix can be found on the following link. youtu.be/qgodA0u5mlQ
This is a comprehensive repair, you will need the service manual, for card and component identification. If the Power supply rails , 5v, 15 and -15v are correct check the rear Card 1 10Mhz output is not drifting, if all OK move onto the removable cards, change all the 10uF, 2.2uF, 22uF, 47uF and 100uF SMD capacitors, around 50-70 caps, take your time and check all the tracks after replacing the capacitors. I would suggest trying a few different removal techniques. I also checked all the SMD RF coils/chokes on every Panel. Two were found to be open circuit. UHF SYNTH 213-041 BOARD 461-436 03, REPLACE L3 560nH
To do in circuit tests, you will need Riser/extender cards. Not all the cards have capacitors that need changing but i would recommend a visual inspection for damaged tracks, dry joints etc.Surecom SW-102HF, unbox and test, Marconi 2966Awayne phillips2023-09-27 | Surecom SW-102HF 1.5-70MHz Power & S.W.R. Meter (SW102HF)
Test conducted with a tuned antenna, SW102HF VSWR is quite accurate, compared with a NanoVNA-F2. I don't think you should trust the Power levels, unless you have the ability to calibrate.
Test Setup: Radio TX modes : FM, CW and RTTY, all gave the same results.
Equipment Marconi Radio test set 2966A Nissei RS-502 SWR and power meter Surecom SW-102HF
Icom IC-706MKIIGYIHUA 948-I Soldering Desoldering Station Unbox and testwayne phillips2023-09-26 | YIHUA 948-I Soldering Desoldering Station Unbox and test
Brought on amazon Uk, cost £155 GBP Seems to work well, update to followBoxford Duet Turn & Mill Duo, Part 6, Mach3 conversion and Costswayne phillips2023-05-13 | Boxford Turn & Mill Duo, Part 6, Mach3 conversion Complete with Costs. All prices UK pounds and all items brought from Amazon UK.
£6.99 Printer Extension Cable USB 2.0 B Adapter Male to Female Connections £21.88 SUPERNIGHT 12V 30A Switching Power Supply £23.00 MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board CNC Controller Card for Stepper Motor Servo Motor £23.99 3 X Dealikee TB6600 4A 9-42V Stepper Motor Driver CNC Controller £10.00 4 Channel Relay Module, 12V 4 Channel Relay Module Optocoupler £12.88 Frequency To Voltage Module, 3.3V/5V/24V 0-100% 100HZ-3KHZ PWM to 0-10V £9.00 Various cable rap, fixing's, cable ties & 5v PSU Total =£107.74Boxford Duet CNC machine, Mach3 conversion (Part 5 final). Spindlewayne phillips2023-05-04 | Boxford Duet CNC machine, Mach3 conversion (Part 5). Spindle
This video covers Mach3 software to test and configure Spindle
This is the Last of the videos for a bit, Duet all working , time now to finish the build by installing the cards and add emergency stop.
Stepper motor Driver is the TB6600.
MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board CNC Controller Card for Stepper Motor Servo Motor.
Frequency To Voltage Module, 3.3V/5V/24V 0-100% 100HZ-3KHZ PWM to 0-10V/0-5V Analog Voltage Converter for Motor Speed Control AD Interface Conversion
5v dc regulator board
Running Pentium XP computer with MACH3 software.
Warning Please be careful as there are mains voltages within the enclosure, PLEASE NOTE, if copying any of my test or modifications, DO AT YOUR own risk, drawing suppled for reference only.Boxford Duet Turn & Mill Duo CNC machine, Mach3 conversion (Part 4). Outputs 1- 4wayne phillips2023-05-01 | Ports and Pins Boxford Duet Turn & Mill Duo CNC machine, Mach3 conversion (Part 4). Outputs 1- 4
This video covers Mach3 software to test and configure Outputs 1- 4
Stepper motor Driver is the TB6600. MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board CNC Controller Card for Stepper Motor Servo Motor. 12V DC power supply 30A. Running Pentium XP computer with MACH3 software.
Warning Please be careful as there are mains voltages within the enclosure, PLEASE NOTE, if copying any of my test or modifications, DO AT YOUR own risk, drawing suppled for reference only.Boxford Duet Turn & Mill Duo Mach3 conversion (Part 3) Homing sensorwayne phillips2023-04-29 | IE5222, 2 wire Inductive sensor Boxford Duet Turn & Mill Duo CNC machine, Mach3 conversion (Part 3).
This video covers the Wiring of the IE5222, 2 wire Inductive sensor, Z,X & Y Axis for home position.
Stepper motor Driver is the TB6600. MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board CNC Controller Card for Stepper Motor Servo Motor. 12V DC power supply 30A. Running Pentium XP computer with MACH3 software.
Warning Please be careful as there are mains voltages within the enclosure, PLEASE NOTE, if copying any of my test or modifications, DO AT YOUR own risk, drawing suppled for reference only.Boxford Duet Turn & Mill Duo Mach3 conversion (Part 2) Stepper motorswayne phillips2023-04-28 | Hi, Just noticed a mistake on the Drawing, DO NOT connect the Mach3 Control Board Pin (GND) to the PSU 0v.
This video covers the Wiring of the Stepper motor control boards interfacing to the original Boxford Stepper motors, Z,X & Y Axis. Stepper motor Driver is the TB6600. MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board CNC Controller Card for Stepper Motor Servo Motor. 12V DC power supply 30A. Running Pentium XP computer with MACH3 software.
Boxford Duet Stepper motor Hybrid Type Stepper Motor MAE SPA HY200 2220 0141 AK04 Stepper Stepping Motor (9031066700) Believed to be 200 steps/revolution, 1.4 A (rated phase current). step angle 1,8°
Warning Please be careful as there are mains voltages within the enclosure, PLEASE NOTE, if copying any of my test or modifications, DO AT YOUR own risk, drawing supplied for reference only.Boxford Duet Turn & Mill Duo Mach3 conversion (Part 1)wayne phillips2023-04-25 | Boxford Duet Turn & Mill Duo CNC machine, Mach3 conversion (Part 1). This video covers the Duet as supplied, test of the Control/isolator board, PWM signal or 0-10v to control the speed of the DC spindle motor. Hopefully the Stepper motor controllers, CPU breakout boards etc will be suitable.
Warning Please be careful as there are mains voltages within the enclosure, if copying any of my test or modifications, DO AT YOUR own risk, drawing suppled for reference only.Akai GX-4000D Main board capacitor and Transistor replacement.wayne phillips2023-04-14 | Akai GX-4000D Main board capacitor and Transistor replacement. PCB LE 5801A Tools needed, Soldering Iron, Solder braid or Pump, Wire cutters and a lot of Patience! Kit required 100uF 16v x 4 220uF 25v x 1 47uF 25v x 6 47uf 16v x 2 0.47uF 25v x 4 10uF 25v x 19 33uF 25v x 1 4.7uF 25v x 7 2.2uF 25v x 4
(2SC458) replace with KSC1845 NPN transistor x 14 TR1, 2 , 3 TR14, 15, 16 TR6, 7, 8, 9 TR19, 20, 21, 22Yaesu FT-710, External ATU LDG AT-200Proii, Z-11PRO IIwayne phillips2023-02-07 | Yaesu FT-710 working with a LDG LDG AT200ProII I believe this also works with the LDG Z-11PRO II
Do at your own risk, works with my setup. Not ideal, its a work around until LDG release a interface cable.
LDG Y-ACC control cable. The BLACK jack plug of the Y-ACC interface cable is for the 1/8” jack marked "Radio" on the rear of the LDG AT200ProII. The RED jack plug is for the REM/ALC socket on the on the rear Yaesu FT-710.
The LDG200ProII will need an external power source. DC power in (2.5 by 5.5 mm power jack marked "Power", center positive). Power requirements: 11 to 15 volts DC at 500mA (750 mA max during tuning)
FT-710 menu setting Press - FUNC - OPERATION SETTING - GENERAL
TUN/LIN PORT SELECT = LINEAR TUNER TYPE SELECT = EXT
Please note, the FT-710 TUNE button will not initiate the tuning cycle.
It is recommended you follow the below procedure every time a tune is required.
Reduce the power of the FT-710 to around 10 watts before you initiate the tuning cycle. Tuning is initiated by pressing the TUNE button on the LDG AT200ProII. If tuning is successful the TX power can now be increased.CREWORKS 8x14 Mini Lathe, Quick Change Tool Post Holder, QCTPwayne phillips2022-12-23 | CREWORKS 8''x14'' Mini Lathe, Quick Change Tool Post Holder, QCTP
Very simple to fit, first test works well.
Amazon Quick Change Tool Post Holder HFS (R) Mini CNC Quick Change Tool Lathe Tool Holder Post Cutter Holder Screw Kit Set Boring Bar Turning Facing Holder Wrench
Digital Vernier Gasea 150mm 6 inch Accuracy LCD Digital Vernier Caliper Gauge Electronic Micrometer Carbon Fiber Ruler Measuring Tool.
Mini lathe CREWORKS 600W 8''x14'' Mini Metal Lathe with LCD Display, HP Motor Mini Benchtop Metal Lathe w 3-Jaw Chuck, 50-2500 RPM Power Metal Lathes for DIY Machining Wood & Metal Working ToolCREWORKS 600W 8x14 Mini Lathe, XL500S Rear wheel Bearing retainerwayne phillips2022-11-26 | Quick over view of the capability of the CREWORKS 600W 8''x14'' Mini Lathe to manufacture an obsolete part for a 1979-81 Honda XL500S Rear wheel Bearing retainer 41231-428-000, 65 x 18.5mm thread M50x1.5.Microsoft Surface Pro, windows 11, Wi-Fi is slow or limited.wayne phillips2022-06-08 | Microsoft Surface Pro, windows 11, Wi-Fi is slow or limited.
My router is a Virgin media Hub 5, it has 2.4 and 5GHz Wi-Fi outputs, My surface pro 6 is running Windows 11, the internet works perfectly on 2.4 GHz Wi-Fi but the Pro defaults to the 5GHz Wi-Fi, which either works intermittently or the connection runs extremely slowly. It is possible to default your Surface pro to the 2.4GHz band, The other option is to alter your Router turning off the 5GHz Wi-Fi.
To gain access to your router, you will need a PC or internet enabled device, in your web browser enter the router default gateway IP address, my virgin media box it address is 192.168.0.1
The password if needed will either be on the router or in your original manual.WAVETEK Schlumberger Stabilock SI 4031 RF Attenuator fault and Fixwayne phillips2022-05-12 | Schlumberger Stabilock SI 4031
for the full repair see youtu.be/AJSm5VRBqQc Do these repairs at your own risk, this video is for information only.
RF Attenuator fault and Fix -20dB chip found to be faulty, could not find an equivalent part so simply made a T pad with 2 x 39R and a shunt resistor of 10R, exact values should be 2 x 40.91R and 10.10R =-20dB. Next job is to change around 70 x 10uf SMD caps!!
Fault Test of the RF Attenuator 226-031S TEST FREQUENCY =100MHz, LEVEL= 0dBA Relays Energized/engaged by pushing the plunger on the end of the relay can. No power supplied.
INPUT OUTPUT BU49 TO BU46 = -70dBA (N0 RELAYS ENERGIZED, Should be -50dBA) ++++
ENERGIZED OUTPUT BU46
RLS2 AND RLS3 = 0dBA (PATH STRAIGHT THROUGHT) RLS2 = -30dBA (PATH THROUGH B3 30dBA) RLS3 = -40dBA (PATH THROUGH B2 20dBA) ++++++
RLS2, RLS3, RLS4 = -30dBA (PATH THROUGH B4 30dBA) RLS2, RLS3, RLS5 = -20dBA (PATH THROUGH B5 20dBA) Above implies RLS2 (B2) which is reading -40dBA should be -20dBA +++++Moonraker SQBM3000N, 2, 70, 23cm Base Vertical, VSWRwayne phillips2022-04-21 | Moonraker SQBM3000N 2, 70, 23cm Base Vertical Region 1 CW and SSB calling frequency is 1296.2 MHz FM simplex calling frequency is 1297.5 MHz 23cm UK The amateur radio band is between 1240 MHz and 1300 MHz.
This model is made of fibre glass construction, pre-tuned and fully weatherproofed. Mast mounting brackets and radials are included.
Specifications:
Frequency: 144,430,1200MHz
Gain: Gain 4.5, 8.3, 10.7dB GRP outer shell Max. power rating 100W Total Impedance:50 Ohms VSWR less than 1.5:1 Mast diameter: 30-62mm Rated wind velocity: 60m sec. Length:1.55m Weight:0.7kgIcom IC-7100 RTC Lithium Battery replacementwayne phillips2022-03-15 | Icom IC-7100 RTC (Real Time Clock) Lithium rechargeable Battery replacement, Fault, IC-7100 not keeping date and Time. The battery is located in the Main control unit. The battery i Have used is NOT a direct replacement.
Original Icom Part number BT6201: ML414HIV01E Replaced with MS621FE, 3V rechargeable Lithium Li-ion battery.
Not one of the easiest Batteries to replace, I would recommend using a Hot air gun with protective Kapton Tape covering the surrounding components. I would recommend placing a piece of insulating tape under and over the battery. NOTE: do at your own risk, this is just a guide to the location of the internal battery.Kenwood TS-870, Fix RX/TX fault on ANT2wayne phillips2022-03-08 | Kenwood TS-870, receive fault on ANT2, Relay K301 not switching
The ANT switch on the front panel when pressed was not switching the rear antenna sockets ANT1 and ANT2. The fault was found to be Q4 FMA7A Emitter common, dual digital transistor. Q4 was not switching on the antenna switching relay K301, when front panel ANT2 selected.Nokta Makro Anfibio multi, internal battery Alternativewayne phillips2022-03-01 | Nokta Makro Anfibio multi, Alternative internal battery. Not much Luck getting the original battery, LP-904085, quoted 6 - 10 weeks delivery from china, ummm, not even sure if it would ever turn up! found this alternative on Amazon.
Note: LP103395, DO NOT USE AS SUPPLIED!! JST power connector pins are the opposite way round, the red and black wires are correct, remove the JST power connector and use the original connector from the original LP-904085
Alternative battery Item model number : LP103395
EEMB 3.7V Lipo Battery 3700mAh Rechargeable Lithium Polymer ion Battery Pack with JST Connector. VOLTAGE: 3.7V; Typical capacity: 3700mAh, Min capacity: 3500mAh; Weight: approximate 74g; Size: 33.5 x 96 x 10.3mm/1.32"x3.78"x0.4" (WxLxH) Price: UK pounds 13.19Tokyo Hy-Power HX-240, 2M to HF Transverter 10-80 mwayne phillips2022-02-24 | Tokyo Hy-Power HF 2M Transverter HX-240 Frequency range 10-80 m
Frequency Range 3.5 / 3.8 / 7 / 14 / 21 / 28MHz ham Bands Mode FM / SSB / CW ( Dependent on radio to be used ) DC Power DC 13.8V 7A max. RF Drive Power 2.5W / 10W Selectable Power Out 30 - 40W p.e.p. ( 30W for FM ) Harmonic Rejection -40dB or better RX Pre-amp Gain Approx. 10dB In/Out Connectors SO - 239 Auto RF Key, Low Noise Pre-amp, Stand-by Jack ( Remote TX Key Jack ), Panel Meter for Power Out, Protections for High SWR and Reverse DC Power Polarity, High/Low Power Out Select. Dimensions (W) x (H) x (D) approx. 146 x 50 x 192 mm Weight approx. 1.3 kgs./ 2.9 lbsBenchtop Jewellery Polishing Buffing Machine and DSM150PS, RPM UT373 & Pat testwayne phillips2022-02-13 | Quick overview and test.
Benchtop Jewellery Polishing Buffing Machine Polisher Buffer Dust Collector Light Voltage: 220V Speed: 0-8000 rpm/min Maximum Polishing/Buffing Mop size 4 inch Motor: 200W Gross Weight: 10.55kg/23.26lbs Case Material: Steel
Holzmann DSM150PS Double Ended Bench Polishing Buffing Machine CE marked Powerful 520 watts 0.75hp motor Speed: 2950 rpm overload controls Material, Cast Iron Weight 12 Kilograms Voltage 230 Volts
UNI-T UT373 Mini Non-contact Digital LCD Tachometer Measurement error of non-contact speed measurement ± (0.04% + 2dgt).
UK PAT Testing With Class 1 appliances, the user is protected by insulation and an earth connection. PAT Testing Class 1 appliances: Earth Continuity and Insulation Resistance tests are carried out. If it is made of metal it must be a Class 1 appliance If it has a three core cable it must be a Class 1 appliance If the plug has a metal Earth pin it must be a Class 1 applianceWeiShi 1900 Timegrapher, Omega Moonwatch & Breitling Blackbirdwayne phillips2022-02-03 | WeiShi 1900 Timegrapher, Breitling Blackbird, Omega Speedmaster Moonwatch professional.
Checked for magnetism using two Apps or a compass. LEPSI - Watch MAGNETISM Tesla - Metal detector and Magnetic field recorder
WeiShi 1900 Checking Beat Rate, Amplitude, and Beat Error
Beat Rate: This tells you the rate of the movement. The number is how many seconds per day your watch is running ahead or behind. Amplitude: This informs you about the health of the movement, specifically by telling you how much rotation (arc) there is in the balance wheel swing, in either direction. Beat Error This number will tell you how varied or consistent the balance wheel swing timing is.Bird 8141 Termaline Coaxial Resistor, strip, clean and test VSWRwayne phillips2022-01-15 | Bird 8141 Termaline Coaxial Resistor, strip, clean and test VSWR
Basically a cylindrical film type resistor immersed in a dielectric coolant. Brought on eBay as not tested.
Thought i would check the internal components and the level of the dielectric coolant.
Oil-Cooled, Power Rating 250W continuous. Frequency Range DC-2500 MHz Warning. Service at your own risk. The Manual states, Service by qualified engineers only! My video is a guide to the internal parts.Faulty Kenwood TM-721 TM-731 Master VFO encoder, Fix KY-040wayne phillips2022-01-10 | Kenwood TM-721 TM-731 Rotary encoder fault and Fix
The original encoder W02-0388-05 is no longer available as original spare part. I tried a few encoders and found the HW-040 or KY-040 Encoder gave the best operation, fit and costing £1 to £2 Uk pounds. Please ignore my spoken parts refence, it defiantly HW-040 or KY-040, not WB-040
Parts needed: HW-040 or KY-040 Rotary encoder (Amazon, DollaTek 5Pcs KY-040 Rotary Encoder). remove R2 and R3, 10K resistors from the rotary encoder board. Remove one of the legs of the Rotary switch, momentary push contact (oversite DT) Remove the original PCB legs and refit or replace so legs are straight and facing down. Link DT to SW. Trim the DT leg flush, cover with tape as the pad below when soldered to the Radio PCB is Ov. Once fitted i used a sticky pad and a little hot melt glue to hold the rotary encoder PCB in place at the correct Hight.Fluke 190C series ScopeMeter Firmware Upgrade, 196Cwayne phillips2021-12-22 | Fluke 190 series ScopeMeter Firmware Upgrade, 196C Need: Optically Isolated Adapter/Cable or OC4USB Latest firmware: fluke.com/en-gb/support/software-downloads PC, my Pc windows 10
Requirements: 1 Fluke 19xC or 2x5C Series ScopeMeter V7.00 or later 2 PM9080 Optically Isolated Adapter/Cable or OC4USB 3 PC with Windows XP or Vista 4 One free Com port or USB port Note: Do not use this upgrade for the FLUEK 199C XRAY ScopeMeter. This firmware does not provide the XRAY functionality Getting Started: 5 Enter the serial number of your instrument in the Instrument DM dialog box. The serial number is printed on the rear of your instrument. 6 Connect your ScopeMeter to COM or USB of your PC using the PM9080 or OC4USB cable 7 Select the Com/USB port to which the ScopeMeter is connected 8 Connect the ScopeMeter to mains power using the BC190 Battery Charger 9 Turn on your ScopeMeter 10 Press the START button to start the upgrade process 11 When the upgrade is successful, a message is displayed. Note that your instrument will switch off and on several times automatically during the upgrade process.Kenwood TS-940S Dot display problem, PLL out of lock. Fixwayne phillips2021-12-16 | Kenwood TS-940S Dot display problem, PLL out of lock. Phase Lock Loops (PLL) going out of lock.
Dot display problem is a Common Fault on the TS range, google and you will find lots of repair ideas. My fix based on visual inspection was to re-solder all the joints on the underside of the Digital A-unit and the PLL board then clean and re-seat all the connectors on both boards.Yaesu FT-991 mod to eliminate the microphone humwayne phillips2021-12-13 | Yaesu FT-991 mod to eliminate the microphone hum
Sorry about the sound quality, my external mike battery was dead so had to add audio in the video editing program. This mod is only for the FT-991. The FT-991A i believe dose not suffer with this problem. Standard mic no hum noise on Transmission. MD-100 or External Boom Mic, loud noise in the background of the transmission. I tried the standard Yaesu fix, single wire from chassis to front panel small board this did not cure the problem. My fix was to add a second wire from the Main large front board to the radio chassis and make a home made ground plane to cover the components behind the the front TFT display. Getting good audio reports, noise seems to have gone :)ICOM IC-271, IC-471, IC-1271 Frequency STEP Modificationwayne phillips2021-12-07 | ICOM IC-271, IC-471,IC-1271 Frequency STEP Modification
Simple mod to convert Frequency step from 5KHz to 12.5KHz leave D19 in place and move D20 to D21 space.
Info from Daniel SP6QKX SETTINGS STEP FM FREQUENCY FOR ICOM IC-271 / IC-471 / IC-1271 Select-matrix are on the LOGIC Unit From the IC6 PIN11 are comon connection matrix diodes Anode( 1N4148 or similar ) to IC12 PIN 3,4,7,8 Cathode Step Diodes instaled ========================================================== 10.Hz Without any diodes 100.Hz D20 1.Khz D19 5.Khz D19 and D20 10.Khz D21 12.5Khz D19 and D21 25.Khz D21a - ( sometimes marked as D34 ) 1.Mhz D21 and D21a -( sometimes marked as D34 ) D21a / sometimes marked D34 only used in IC-471 / IC-1271Behringer ULTRAGRAPH PRO FBQ3102, Fault and fixwayne phillips2021-12-07 | Behringer FBQ3102 Ultragraph Pro 2 x 31 Band EQ
Warning the unit contains mains voltage, play carefully!!
Fault No input signal both channel 1 and 2 both showing +3dB
Fault found to on power supply board, 7915 voltage regulator faulty and associated capacitors.
Sliders cleaned with Contact cleaner, helped to remove crackle sound and slider LED's remaining on.IC-7700, FTM400, IC-271H using RODE NT1-A & Behringer MIC2200, FBQ1502HD MX822wayne phillips2021-12-05 | Microphone replacement using RODE NT1-A & Behringer MIC2200, FBQ1502HD and MX822
The RØDE NT1-A large diaphragm 1" cardioid condenser microphone.
Behringer Ultragain Pro MIC2200 Audiophile Vacuum Tube Microphone/Line Preamplifier.
Behringer Ultragraph Pro FBQ1502HD Professional 15-band stereo graphic equalizer for live and studio applications. amzn.to/3rGKsFQ
Behringer Ultralink Pro MX822 Eight Channel Stereo Rackmount Splitter/Mixer.
3 pin XLR radio interface leads fron TecchnoFix.Behringer MIC2200 Ultragain Pro, Faulty, Repair and Fixwayne phillips2021-10-08 | Behringer MIC2200 Ultragain Pro Mic Preamplifier Intermittent fault on channel 1
Simple fix, probably a dry joint on the input board, XLR or 1/4 Jack sockets. Quick resolder of the main XLR and 1/4 Sockets and all working fine now. Don't think i would have brought a MIC2200, not one of Behringers Best!! this was a faulty gift and will suit my needs, 20dB gain for the Dynamic mic and i am not looking for a Ultra-wide bandwidth from 2 hz to 200 khz, my radio filters cut of around 2.8Khz.RM Italy BLA350 Plus 300W Linear Amplifier faulty, Part 1wayne phillips2021-09-20 | RM Italy BLA350 Plus 300W Linear Amplifier faulty
Brought on eBay, described as PA stage OK but faulty SWR or Temp control circuit!! Ummm not quite the case. In this video I will trace the output from the PA FETs pads through the Low Pass filters and control relays to the Antenna Output relay and Socket.
Part one. To Do
Check the output MRF150 MosFets. Check the low pass filters SWR and Zo to the Antenna socket. Check the Low Pass filter with Spectrum analyser and tracking generator. Check the operation of the NTC safety devices.
Findings. Both the MRF150 faulty!! SWR,Z0 and filter response found to be OK. NTC controlling the Fans working OK NTC sensing the FET's (10K), seems to be working OK. Heating the NTC and placing a volt meter on the MRF150 FET Gate pad, as The NTC heated up this would appear the voltage dropped on the FET Gate pads.
Few more things to check on the Input side of things, will be in Part 2Icom IC-7700 Setup for FT8, FT4 using WSJT-X, USB Audio Adapter Sound Card with SPDIF Digital Audiowayne phillips2021-09-16 | Icom IC-7700 Setup Data Modes for FT8, FT4 etc using WSJT-X and external USB Audio Adapter Sound Card with SPDIF Digital Audio.
This is my setup, please see below for cables and interface required. Windows 10 64 bit IC7700 firmware 2.10
The Icom CI-V interface is not a standard RS-232 type interface. The signals are TTL-level. Allows you to change frequencies, operating modes, and memory channels using your computer and appropriate third party control software.
Neutron http://keir.net/neutron.html Neutron is a very simple and small time synchronizing program that retrieves the accurate time from one of several specialized time servers on the Internet.
WSJT-X https://physics.princeton.edu/pulsar/k1jt/wsjtx.html WSJT-X implements communication protocols or "modes" called FST4, FST4W, FT4, FT8, JT4, JT9, JT65, Q65, MSK144, and WSPR
1. Install the two Toslink Cable into the rear of the IC7700.
2. install the CI-V cable.
3. Install the startech USB Audio Adapter as per supplied instructions. set outputs to SP/DIF, Insattall cables from IC7700
4. IC7700 Menu SET - ACC and find “DATA2 MOD”. Change the option to SPDIF.
5. configure WSJT-X as per my settings.
Please see my other video if you have Icom RS-BA1 software youtube.com/watch?v=YEoMErbpp38&t=1sMotoRadds Motorcycle Chin Mount on Schuberth C4, tested on BMW R1200GS with GoProwayne phillips2021-09-15 | MotoRadds Motorcycle Chin Mount on Schuberth C4, tested with GoPro 6 Black, followed by a Quick test on the BMW R1200GS.
MotoRadds Motorcycle Chin Mount Brought on Amazon, amzn.to/397bo7m
The MotoRadds Motorcycle Chin Mount is a Push fit, the wings are a good match for the profile of the Schuberth c4 helmet chin guard. There is a approx 3mm gap on the centre fitting but this was made up using more of the foam type 3M double sided Tap. There is a draw back to mounting on the chin guard with flip type helmets, basically if you wish to ride and record with the flip UP you will get a lovey recording of the sky!! The Schuberth C4 is not dual-homologated or P/J homologated, therefore in the UK it is not legal to ride with the Schuberth C4 chin guard in the up position.Icom IC-7700 Setup Data Modes for FT8 using WSJT-X and RS-BA1wayne phillips2021-09-14 | Icom IC-7700 Setup Data Modes for FT8 using WSJT-X and RS-BA1 Remote Utility.
please see my other video if you do not have RS-BA1 software. Icom IC-7700 Setup Data Modes for FT8, FT4 etc using WSJT-X and external USB Audio Adapter Sound Card with SPDIF Digital Audio. youtube.com/watch?v=5YnQ2b9M9NQ
The Icom CI-V interface is not a standard RS-232 type interface. The signals are TTL-level. Allows you to change frequencies, operating modes, and memory channels using your computer and appropriate third party control software.
Icom RS-BA1 version 1 The RS-BA1 installer will install the Remote Utility, Remote Control , Icom Virtual Serial Port, and Icom Virtual Audio Device.
1. Configure the Icom RS-BA1 as per supplied instructions.
2. install the CI-V cable.
3. PC Soundcard setup. Select the Icom Virtual Audio device.
4. ON the Icom Remote Utility set the MOD to V Audio instead of Mic.
5. IC7700 Menu SET - ACC and find “DATA1 MOD”. Change the option to LAN.
6. configure WSJT-X as per my settingsIcom IC-7700 MARS/CAP Modificationwayne phillips2021-09-12 | Icom IC-7700 MARS/CAP Modification
DISCLAIMER: Modify your rig at your OWN RISK.
This modification is for the EUR/UK version. TX from 1.6 - 30 MHz and 50-54 MHZ
You will loose auto Band end markers and Beeps. After being modified a full system reset is required before you power on the IC-7700
Reset: Press and hold the [F-INP ENT] and [ MW ] buttons, push [ POWER ] button to turn the IC-7700 on. The IC-7700 CPU is reset.Yaesu FT-897D PTT Mod, ACC Jack Socket for Amplfier, Microset SR-300wayne phillips2021-09-07 | Part 1 Yaesu FT-897D to Linear Amplifier Microset SR-300 Using Rear ACC jack stereo Socket
When i received my Amplifier there was no instructions or manual, Microset web site is a waist of time, numerus emails asking about the external PTT socket levels, Nothing Back!!!
FT897D working ok with the internal link changed. In Standby on the 3.5mm Jack plug, TX pin = 5v DC Pressing the Microphone PTT, TX drops to 0vDC
Unfortunately the Microset Amplifier external PTT Jack is Active High!!
Time to build an TX signal inversion board.
Part two to include SR-300 internals and circuit for TX signal inversion board.Diamond X510N & X510MH Antenna Teardown, is it a Fake?wayne phillips2021-08-26 | Comparison of Diamond Antenna X-510N (200W) Vs Diamond X510MH (330W)
Brought the X510HM new from good a UK supplier, but is it a Fake? Nothing about The X510MH seems to have the build quality of Diamond X510N.
Did you ever wondered what was inside? All the measurements were taken on my LCR at 100KHz and 1v.
X510N Base Antenna Specifications: Band: 144-147/430-440 Gain (dB): 8.3/11.7 Watts: 200 Connector: Type-N Weight: 5 lbs. Length: 17.2' Max Wind Resistance: 90 MPH
X510MH Base Antenna Specifications: Band: 2m/70cm Gain (dB): 8.3/11.7 Watts: 330 (2m) / 250 (70cm) Connector: SO-239 Weight: 5 lbs. Length: 17.2' Max Wind Resistance: 90 MPHNanoVNA-F V2 Vs original NanoVNA, overview and Test of Diamond X510wayne phillips2021-08-15 | NanoVNA-F V2 Vs original NanoVNA, overview and Test of Diamond X510 Brought from Amazon amzn.to/2YVgUrP
Very basic comparison of size, LCD display, box contents and reading of the NanoVNA-F V2 4.3inch and original NanoVNA 2.8inch.
Very little difference in the results from the Diamond X510 on 2m. Both units calibrated with the same Open, Short and Load.
Would you upgrade? In my case YES, my eyesight is getting worse and the Original NanoVNA is getting difficult to see without the aid of a magnifier.
The original NanoVNA covers 50KHz to 900MHz, 2.8 inch LCD. NanoVNA-F V2 covers 50KHz to 3GHz ( ideal for 23cm and 13cm) 4.3inch lcd.
Main disadvantage of both is there screen is so reflective, in normal sunlight very hard to see, I did attempt to photo but all i got was reflections.NanoVNA-F V2, 4.3inch sysjoint Firmware Updatewayne phillips2021-08-13 | NanoVNA-F V2, 4.3inch sysjoint firmware Update Brought from Amazon amzn.to/2YVgUrP DO THIS AT YOUR OWN RISK!!! Make sure you have the correct device!
PC software and Firmware: http://www.sysjoint.com/en/content/?144.html Download the Firmware file NanoVNA-F_V2_App_v0.3.0.zip, unzip into a folder on your PC. When prompted ( see below) Copy and paste ‘update.bin’ from your PC into the U-Disk.
Procedure: The firmware of NanoVNA-F V2 can be upgraded through virtual U-disk without a programmer. The upgrade needs to be done with the USB Type-C cable. Connect NanoVNA-F V2 to PC with the USB Type-C cable. Push and hold the middle push button, then power on NanoVNA-F V2. The device will be recognized as a U disk drive. The following prompt information will appear on the device screen. Firmware upgrade: 1. Connect the device to PC with Type-C cable; 2. The device will be recognized as a U-Disk; 3. Copy ‘update.bin’ into the U-Disk; 4. Power off and on;
Download the firmware file and unzip it to get ‘update.bin’. Copy ‘update.bin’ into the U-Disk, it may take 10-15 seconds. Power off and on the device, the firmware upgrade will complete automatically.DC Blocks are not made equal, tested with a spectrum analyzer SSA3021X. Part 2wayne phillips2021-08-06 | Part 2 Not all DC Blocks are made equal, tested with spectrum analyzer SSA3021X
Please see my previous video for a more in depth look at the DC blocks as listed below Test equipment: Siglent SSA3021X and ET4410 LCR Meter, DC Blocks: Tektronix: Part No. 015-0221-00 ,unknown manufacture 0.1uF and eBay purchase DB6.0-M-MF
Not all DC Blocks are made equal!!! buy cheap get what you pay for! DB6.0-M-MF latest purchase from eBay £10, will not be using this one.
DB6.0-M-MF 5W Stainless Steel RF Coaxial DC Block DC-6GHz 50ohm Series: IN-Series Impedance: 50 Ohm Frequency Range: DC to 6GHz VSWR: less than 1.35 Insert Loss: 0.7db RF Power range: 5W Test DC Voltage: 100V Capacitance 200pFInsertion Loss of a DC Block for use with a spectrum analyzer SSA3021X.wayne phillips2021-08-05 | Insertion Loss of a DC Block for use with a spectrum analyzer SSA3021X.
Test equipment: Siglent SSA3021X and ET4410 LCR Meter, DC Blocks: Tektronix: Part No. 015-0221-00 and unknown 0.1uF
Basic not technical look at the insertion loss of DC Block for spectrum analyzer.
IF your spectrum analyzer has a yellow warning tag under the RF input port, "+dBm, 0VDC", avoid any DC on the RF input.
DC block can be thought of as a high-pass filter, preventing the flow of DC signals in to system while providing minimum impedance to RF signals. The example shown and being tested are known as "Inner DC Block", the capacitor is placed in series with the center conductor .
DC block, measure or refer to the manufactures spec sheet and keep in mind the insertion loss of the DC block.
Tektronix: Part No. 015-0221-00 - 0.5 to 2GHz - 47nF - 50V.Fluke 196C ScopeMeter, Basic Probe Cal & Functions.wayne phillips2021-07-31 | Fluke 196C ScopeMeter, Probe Cal & Functions.
Another "sold as seen" eBay purchase, just thought i would run some basic tests, Voltage, Resistance, Scope and Probe calibration. Not a lot on the net, this is no way a full function test, just my findings straight out the delivery box.Aeroflex 3281A Analyser, basic strip down, Install XP SP3 and MiniVna Prowayne phillips2021-07-19 | Aeroflex 3281A Spectrum Analyser basic strip down, Backup the HDD, Install XP SP3 and MiniVna Pro
Opened the 3281A up to backup the 160GB IDE HDD before installing windows XP Service Pack 3. SP3 Installed OK, no problems. Next option, the 3281A dose not having the TG option installed, probably cost a small fortune from Aeroflex! my cheapest option as the device runs on Windows XP was to install Java, FTDI drivers to run a miniVNA PRO, again runs fine.Aeroflex 3281A Spectrum Analyser 3Hz to 3GHzwayne phillips2021-07-12 | Aeroflex 3281A Spectrum Analyser 3Hz to 3GHz
latest purchase on ebay, seller selling as new old stock, manufactured 2010. Operating System: Windows XP Pro for Embedded Systems Specifications: Low end frequency limit 3.00 Hz High end frequency limit 3.00 GHz Resolution Bandwidth Min. 30 Hz Resolution Bandwidth Max. 5.00 MHz Amplitude RangeDANL to +30 dBmFeather Touch Micro Focuser, Model:FTM-CPC11, bushing/Washer 1805wayne phillips2021-06-30 | Feather Touch Micro Focuser Model:FTM-CPC11, bushing/Washer 1805 Brass bushing/Washer 1805
Lost but then found a few days later, so i decided to draw the dimensions up. From a third party I was told the Cost from Starlight is $1.20 plus shipping.
Material: Brass or bronze
Outer Diameter = 9.60mm Inner Diameter = 5.50mm Thickness = 2.00mm Measured with digital verniers, not calibrated, expect some small tolerance's, there seems to be a very slight bevel to the outer edge.Diamond X510 VSWR, Siglent SSA3021X, R&S FSH3, NanoVNA & MiniVNA Prowayne phillips2021-06-20 | Diamond X510 VSWR, Siglent SSA3021X, R&S FSH3, NanoVNA & MiniVNA Pro
This was a quick and basic comparison of VSWR measurement of a Diamond X510 2M/70cm antenna on the 2M band. Setup: Center frequency 145.5MHz, Span 10MHz Calibrated with the same Short, Open and Load (50R) termination. Equipment: Rohde & Schwarz FSH3 Spectrum Analyzer (with tracking gen) Siglent SSA3021X Spectrum Analyzer (with tracking gen) MiniVNA Pro (output via android device (Bluetooth) or PC (USB)) NanoVNA. VSWR DEVICE 143.6MHz 145.5MHz 146.9 MHz FSH3 1.18 1.761 1.042 SSA3021X 1.16 1.629 1.009 MiniVNA Pro 1.07 1.57 1.05 NanoVNA 1.1 1.5 1.1
Conclusion: If you want to do basic VSWR checks, get the NanoVNA (new £40), the miniVNA (£125 used) is a little fiddly to setup on the PC but works well via Bluetooth. The R&S (£800 used) and Siglent with bridge and software (new £1800) are over kill.miniVNA PRO, windows 10 & 7 install, 32 and 64 bitwayne phillips2021-06-06 | miniVNA PRO windows 10 install 32 and 64 bit Suggest you make a folders on your PC for downloads and installs.
1. IMPORTANT!! check for Java WE need to run the MSdos command prompt. type cmd in search bar (bottom left next to windows icon), click on command prompt type
Plug MiniVNA Pro into USB port, Run Device Manager, check your port comm Number. Will need this. create a desktop shortcut or click on vnaJ file, should run if java installed correctly.
Working: windows 7 32bit vnaJ.3.4.7 windows 10 32bit vnaJ.3.1.13 windows 10 64bit vnaJ.3.1.13 Kindlefire HD 7 (X43Z60) app BlueVNA via Bluetooth
Tested on 2 x laptop HP 8470P EliteBook System type 64-bit operating system, x64-based processor Windows 10 Pro, Version 20H2, OS build 19042.985 System type 32-bit operating system, x64-based processor Windows 10 Pro, Version 20H2, OS build 19042.985
Advent 7039 System type 32-bit operating system, x64-based processor Windows 7 Home Premium, Version Service Pack 1
Kindlefire HD 7 (X43Z60)Yaesu FT-817ND Faulty no display, fixedwayne phillips2021-06-01 | Brought on eBay as spares or repair, 80 UK pounds, Bargain, complete with just about every add on you can get. Fault reported as Polarity revered, the previous owner had previous work done BK1608HS601T Filter replaced, still dead! I checked DC input and charger circuit, all tested OK but then i noted the ribbon cable to the head unit had burn marks. The fault was on the head unit, a 5v regulator Q4013, S-812C Series (S-81250SGUP) was burnt, i temporally fitted a LP2950 5v reg and this allowed the unit to power up.Radioddity DB25, TX Power levels & SINAD, totally Deaf against FTM400wayne phillips2021-05-27 | Radioddity DB25, TX Power levels & SINAD, totally Deaf against FTM400
Sensitivity of 0.167 µV for a 12 dB SINAD Power (approx) 144Mhz, High = 25W, Low = 12W 430Mhz, High = 20W, Low = 9W Standy current= 18mA, monitor = 220mA This radio is deaf, I think it is a problem with the digital squelch. Software from web site dose not work on windows 10 or 7, Data cable supplied dose work with Chirp software. Shares its build and menu with QTY 8900D. I found unless the received signal is 5:9 (squelch=1) you wont hear anything unless you press the MONI button on and then off.