Uploaded November 2026 | Updated November 2026, 3 days ago
See the Airmoto portable tire inflator in use, from connecting the air hose and setting the PSI target to inflating car tires and recharging the pump. This hands-on demonstration follows the controls and tire-valve connection for viewers getting familiar with the Airmoto air pump.
I work around the car, check the displayed pressure, start and stop inflation, and pause to recharge when the battery runs out. The video also shows the hose getting hot and my observations about battery use and stopping the pump. It documents what happened during this session, including the recharge break, rather than a verified battery-capacity or automatic-shutoff test.
Tire-pressure correction: use your vehicle’s recommended cold tire pressures on the door placard or in the owner’s manual. The tire sidewall maximum and the 40 PSI target shown here are not general recommendations. Do not use the spoken rain/ice comments as advice to change pressure. Follow the inflator’s operating and cooling instructions, and check the final pressure with a suitable gauge. NHTSA guidance: nhtsa.gov/vehicle-safety/tires
Subscribe for more practical car and tool demonstrations, and share which tire-inflator controls you would like explained next.
Please Subscribe To My Channel For More Great Content: youtube.com/channel/UC0GhF05mfZjmSRLGqwlB2zQ?sub_confirmation=1
Disclaimer: This video is for general informational purposes only and does not constitute medical, financial, legal, mechanical or professional advice. I am not a licensed professional. Always consult with a qualified expert before making decisions based on this content. Any actions taken are strictly at your own risk. This video may contain affiliate links.
0:00 Airmoto introduction and pressure discussion
0:54 Valve cap and air-hose setup
1:27 Powering on and setting the PSI target
2:01 Starting inflation on the first tire
3:52 Stopping and disconnecting the hot fitting
4:50 Connecting to the second tire
6:34 Checking the pressure and stopping manually
7:12 Moving to the third tire
8:05 Battery runs out and recharging begins
9:09 Resuming after recharging
10:58 Moving to the fourth tire
11:40 Pressure display and plus/minus controls
12:12 Finishing with a low battery
12:52 Final pressure discussion and wrap-up
See the Airmoto portable tire inflator in use, from connecting the air hose and setting the PSI target to inflating car tires and recharging the pump. This hands-on demonstration follows the controls and tire-valve connection for viewers getting familiar with the Airmoto air pump.
I work around the car, check the displayed pressure, start and stop inflation, and pause to recharge when the battery runs out. The video also shows the hose getting hot and my observations about battery use and stopping the pump. It documents what happened during this session, including the recharge break, rather than a verified battery-capacity or automatic-shutoff test.
Tire-pressure correction: use your vehicle’s recommended cold tire pressures on the door placard or in the owner’s manual. The tire sidewall maximum and the 40 PSI target shown here are not general recommendations. Do not use the spoken rain/ice comments as advice to change pressure. Follow the inflator’s operating and cooling instructions, and check the final pressure with a suitable gauge. NHTSA guidance: nhtsa.gov/vehicle-safety/tires
Subscribe for more practical car and tool demonstrations, and share which tire-inflator controls you would like explained next.
Please Subscribe To My Channel For More Great Content: youtube.com/channel/UC0GhF05mfZjmSRLGqwlB2zQ?sub_confirmation=1
Disclaimer: This video is for general informational purposes only and does not constitute medical, financial, legal, mechanical or professional advice. I am not a licensed professional. Always consult with a qualified expert before making decisions based on this content. Any actions taken are strictly at your own risk. This video may contain affiliate links.
0:00 Airmoto introduction and pressure discussion
0:54 Valve cap and air-hose setup
1:27 Powering on and setting the PSI target
2:01 Starting inflation on the first tire
3:52 Stopping and disconnecting the hot fitting
4:50 Connecting to the second tire
6:34 Checking the pressure and stopping manually
7:12 Moving to the third tire
8:05 Battery runs out and recharging begins
9:09 Resuming after recharging
10:58 Moving to the fourth tire
11:40 Pressure display and plus/minus controls
12:12 Finishing with a low battery
12:52 Final pressure discussion and wrap-up










