A4 DTF Printer Scratching Film? Check the Height and Support @BCHTechnologies
A4 DTF Printer Scratching Film? Check the Height and Support  @BCHTechnologies
Uploaded September 2026 | Updated November 2026, 2 days ago
Getting head strikes at the beginning of your DTF film? Kevin shows how film position and output-support height can affect clearance, then tests paper-based transfer media using Yink Studio.
The first sample has strike marks on both sides near the leading edge. Kevin demonstrates setting the film farther back on its backing sheet and adjusting an output-support platform so it sits slightly below the printer’s exit without catching the media. The bubble level helps track the adjustment when one side needs to sit lower.
Stacking film on paper adds thickness, and the two layers can shift relative to each other. Kevin then tries paper-based transfer media as an alternative to that two-layer arrangement on the setup shown.
For the longer media, the video covers a rear duplex extender, page-height settings in Yink Studio, and a three-row repeat layout. Measure the actual cut length before setting up the job—the last repeat in this test did not come out correctly because the paper length had not been measured.
This is a feeding and printing demonstration. It does not establish wash durability or finished-garment performance for the paper-based media. Film-only feeding requirements and hardware modifications depend on the printer and conversion.

Paper Based DTF Film: https://link.amazon/B003EduPd
Platen Extender: bchtechnologies.com/collections/a4-true-dtf-solution/products/bch-4-point-adjustable-dtf-film-platen-leveling-platform-for-epson-printer-conversion
Rear Paper Feed Extender: bchtechnologies.com/collections/a4-true-dtf-solution/products/bch-adjustable-rear-paper-feed-support-extension-for-epson-dtf-film-23-40-cm
4ColorDTF Conversion Kit: bchtechnologies.com/collections/a4-true-dtf-solution/products/a4-basic-conversion-kit
Chapters

Are printhead strikes ruining your prints? Learn effective DTF film leveling to fix scratches and protect your machine.

Dealing with scratched transfers is frustrating, especially when it happens right at the start of a job. These printhead strikes usually signal that your setup needs a physical adjustment. If you are operating a high-speed printer, you are working with a lower printhead clearance than standard models, which makes proper alignment even more critical for successful results in your shop.

The solution is often simpler than replacing parts. By taping your film back to create a specific buffer zone, you can prevent the material from catching on the head during the initial feed. Taking a moment to measure the necessary distance ensures your DTF printing process runs smoothly without damaging your equipment or wasting expensive supplies.

Subscribe for weekly printer maintenance tips, and let me know in the comments if you have questions about your specific setup.

00:00 Head strikes at the beginning of the film
00:15 Set the film back on its backing sheet
00:32 Adjust the output support
01:25 Film thickness and movement
01:48 Film-only feeding discussion
02:10 Paper-based transfer media
03:03 Longer media and the duplex extender
03:12 Yink Studio page height and repeat layout
03:46 Printing demonstration
04:53 Why measuring the paper length matters
Find related DTF parts and printer resources at BCHTechnologies.com. Subscribe for practical printer repair, DTF conversion, and printing tests.
A4 DTF Printer Scratching Film? Check the Height and SupportTransform Your Model J Printer Into a 3,000 Shirt WorkhorseThe Final Pieces: Printhead & MainboardWhy Your DIY Printer Repair Might Be Failing 🛠️Automating Your Printer Workflow with SensorsThis tiny cable mistake kills Epson printers #printerrepair #dtf #diyThis Tiny Cable Controls Your Entire Printer #ElectronicsRepair #Satisfying #529How a Simple Lever Controls Your Printers Paper Tray #printerrepair #techsupport #536LCD Panel Wont Power after DTF Conversion? Your Scanner Cable Connection is WrongHP Pagewide Printhead Repair ResultAre Expensive DTF Printers Worth It? Let’s Test the ColorHow to Remove an Epson Scanner in 3 Simple Steps!
Kevin at BCH |

A4 DTF Printer Scratching Film? Check the Height and Support

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER