Mr.D - Falling with style | A better hands free climb/descent for INAV, ArduPilot, and other flight controller firmware @MrD | Uploaded September 2023 | Updated October 2024, 2 days ago.
🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC
In this video, we revisit a nice addition to your transmitter model. This will allow you to climb or descend as a set rate. I have shown you how to do this before. But this new version is much better. Now you can enable and disable your climb or descent without needing to change the rate. There are also nice automated entries and exits for this assistance feature.
✈️ Contents ✈️
00:00 Introduction
01:16 How the old version worked, and how the new version will work
02:08 How I have the basic models setup on the transmitters
02:47 Step 1 - Disable the trims (OpenTX/EdgeTX)
03:35 Step 1 - Disable the trims (ETHOS)
04:15 Step 2 - Adding the pot and curve for the hands free climb/descent (ETHOS)
07:07 Step 2 - Adding the pot and curve (OpenTX/EdgeTX)
09:33 Step 3 - Setting up the logic and assigning it to the mix (OpenTX/EdgeTX)
10:15 - Logic for detecting the flight modes
12:12 - Logic to activate the hands free climb/descent
14:45 - Logic to deactivate hands free climb/descent
16:25 - Latching switch for hands free climb/descent enabled
17:35 - Setting up the switching in the mixer
17:58 - Demo of the system working
19:00 Step 3 - Setting up the logic and assigning it to the mix (ETHOS)
19:02 - Logic for detecting the flight modes
21:40 - Logic to activate the hands free climb/descent
23:55 - Logic to deactivate hands free climb/descent
25:59 ETHOS comments and how they can be really useful
27:09 - Latching switch for hands free climb/descent and the OR for activating
29:25 - Setting up the switching in the mixer
29:50 - Demo of the system working
30:50 Conclusion
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.
✈️ In this video ✈️
⚙️ FrSky TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro
⚙️ FrSky Horus X10S Express transmitter: bit.ly/MrD_3l7b8K5
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
#INAV #AutoClimb #OpenTX #EdgeTX #FrSkyETHOS
🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC
In this video, we revisit a nice addition to your transmitter model. This will allow you to climb or descend as a set rate. I have shown you how to do this before. But this new version is much better. Now you can enable and disable your climb or descent without needing to change the rate. There are also nice automated entries and exits for this assistance feature.
✈️ Contents ✈️
00:00 Introduction
01:16 How the old version worked, and how the new version will work
02:08 How I have the basic models setup on the transmitters
02:47 Step 1 - Disable the trims (OpenTX/EdgeTX)
03:35 Step 1 - Disable the trims (ETHOS)
04:15 Step 2 - Adding the pot and curve for the hands free climb/descent (ETHOS)
07:07 Step 2 - Adding the pot and curve (OpenTX/EdgeTX)
09:33 Step 3 - Setting up the logic and assigning it to the mix (OpenTX/EdgeTX)
10:15 - Logic for detecting the flight modes
12:12 - Logic to activate the hands free climb/descent
14:45 - Logic to deactivate hands free climb/descent
16:25 - Latching switch for hands free climb/descent enabled
17:35 - Setting up the switching in the mixer
17:58 - Demo of the system working
19:00 Step 3 - Setting up the logic and assigning it to the mix (ETHOS)
19:02 - Logic for detecting the flight modes
21:40 - Logic to activate the hands free climb/descent
23:55 - Logic to deactivate hands free climb/descent
25:59 ETHOS comments and how they can be really useful
27:09 - Latching switch for hands free climb/descent and the OR for activating
29:25 - Setting up the switching in the mixer
29:50 - Demo of the system working
30:50 Conclusion
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.
✈️ In this video ✈️
⚙️ FrSky TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro
⚙️ FrSky Horus X10S Express transmitter: bit.ly/MrD_3l7b8K5
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
#INAV #AutoClimb #OpenTX #EdgeTX #FrSkyETHOS
