99-03  7.3L Up Pipe Top Bolt Access W Tool List @keithnoneya
99-03  7.3L Up Pipe Top Bolt Access W Tool List  @keithnoneya
Uploaded November 2026 | Updated November 2026, 1 day ago
This video covers how to access the Up-Pipe Upper Flange Bolts on a 99-03 F250/350. So parts do apply to Excursions.
Note; this is NOT instructions for removing and re-installing the Up-Pipes or the Turbo. There's plenty of videos on that, however they usually miss details on removing and installing the Y-Pipe bolts. That's what this video discusses.
A small word of Caution, it's NOT un-common for kits to come missing parts. Check your Kit BEFORE you pull your Turbo and Up-Pipes!
However, for my Up Pipes I used the Dorman 679-005 kit at around $99-180.00. The two Factory Sealed Dorman kits I bought at Advance Auto, both came missing parts. One was missing the Flange Gaskets and the other was missing a bolt. So again CHECK your kit contents BEFORE you leave the store, AND BEFORE you pull the Turbo and Up Pipes off.
- If you’re missing the Gasket for the Y-Pipe you can get them at RiffRaff for approx. $24.00 here; riffraffdiesel.com/bellowed-up-pipe-accumulator-gasket-set-99-5-03 I posted the RiffRaff link because I couldn’t find any in town at the local parts stores.
- You can also use SWAG for around $139.00 here; ebay.com/itm/232543762924
- After my Dorman Up Pipe Installation in in June of 2022 I drove the truck cross country 8 times at 1,600 miles each way, not the mention the months I drove while at my destination. They’re still Working great since I installed them in June of 2022.
- To install my Up-Pipes "I" pulled the Passenger Inner Wheel Well off, and went in right above the frame. You don't have to do that, but it makes he job easier, but costs about an hour of time. If you pull the Pass Inner Fender Well out, you then have access the Drivers Y-Pipe bolts by going just above the truck frame.
- For the Drivers side bolts I came in from under the truck on the driver’s side.

- A word of caution. If you have 6 sided bolts use a 6 sided socket, if you have a 12 sided bolt use a 12 sided socket. If you use a 12 sided socket on the that 6 sided bolt, it'll strip.

The bolt on the on the back passenger side Y-Pipe can NOT be tightened using a wrench, you’ll have to come in from the bottom of the truck, or remove the Inner Fender Well, then use a socket and extensions like I did.

Here’s a list of tools and two pictures to help.
Tools to reach Up Pipe bolts I used;
- 1/2” Ratchet.
- 9” Extension 1/2” Drive.
- 9” Wobble Extension 1/2” Drive. Harbor Freight.
- 4” Extension 1/2” Drive.
- 1/2” to 3/8” Drive Adapter.
- 6” Extension 3/8” Drive.
- 6” Extension 3/8” Drive.
- 3/8” Impact Swivel. I used this because is has limited offset, you might be able to use a Wobble.
- 10mm Socket 3/8” Drive, 6 or 12 Points depending on bolts in the kit.

Coat the Y-PIPE Bolt threads with some Anti-Seize compound like Permatex 81343 amazon.com/dp/B0002UEOLO/?th=1 Tighten the top Y-Pipe Bolts ALL the way and leave the bottom ones a little loose at the Exhaust Manifolds. This is important so you can get everything lined up, especially the Turbo Alignment Pin to the Y-Pipe.

- Turbo Clamp Notes:
The Turbo Clamp, I had to pull the nut & bolt off the Turbo to Y-Pipe Clamp, then put the bolt & Nut in the clamp. Then I used an electric Ratchet with a Wobble Extension to tighten the nut. It's NOT FUN, very tight area back there! The down Pipe and Y-Pipe Clamps are on still VERY tight after Loosening the nuts. Tap them gently and wiggle the turbo with a long large wood rod, or the jack handle with a towel wrapped around it. New Clamps are available at RiffRaff.

- Up Pipe Heat Shield Notes:
Prior to installing the Up Pipes, you should transfer the heat shield from the old ones to the new ones. You’ll need to remove the Metal Retaining Straps.
The Metal Straps are held in place using a metal retainer ball, you have to slightly pry up the metal tab with a 000 blade screw driver to allow the metal ball to release the strap.
I couldn't find stock clamps so use some 1/4" Gates Screw Clamps.
Hope that helps point you in the right direction. Sorry I didn’t do a video earlier, but I was in a hurry to visit my sick dad.
Please comment your experiences and Ideas below.
However if you would like to help, give me a subscription on my YouTube channel. Best Blessings. Keith Noneya
Best Blessings. Keith Noneya
99-03  7.3L Up Pipe Top Bolt Access W Tool List1996 to 2002 Caravan Drivers CV Axle Step by Step Change Part 3 of 4Harbor Freight 110 amp Dual MIG Welder PWR Cord Upgrade part 1Cataract Lake Area Williams Arizona Oct 20212003 Cadillac CTS Drivers Quarter Panel More Filler  Part 15 ofJessicas Family restaurant Williams AZHarbor Freight 110amp Dual Mig Welder PWR Cord Upgrade part 22003 Cadillac CTS A Piller 1st Prep & Welding Part 4A ofMatt & Hanna Rose Lead TLC  Worship One Last Time TLC2001 to 2006 Caravan EASY Motor Mount Change Passenger Side PN EM-29262003 Cadillac CTS Drivers Quarter 1st Wet Sand Part 32 ofNo Not Today Sarah Rose TLC Slidell La.
Keith Noneya |

99-03 7.3L Up Pipe Top Bolt Access W Tool List

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER