peugeotCitroen2CVThe process of getting a mates Renault Avantime V6 back up and running again. As far as i know this car has not run for approximately 7 years, 1 of which it sat outside my shed waiting as i got through a 406 then 407 project.
The first steps mainly in this video concern getting the Avantime started and running. By the end of the video it was running and a nasty ticking sound was cured with an oil flush and new oil.
The next videos will cover the removal of the engine, dealing with the rust on removable parts such as the subframe, rear axle and radiator support bar. With the engine out the timing belt and rocker covers will be addressed.
If you have any tips or advice regarding working on these Avantimes that is more than welcome.
Renault Avantime Recomissioning Part 1peugeotCitroen2CV2022-03-13 | The process of getting a mates Renault Avantime V6 back up and running again. As far as i know this car has not run for approximately 7 years, 1 of which it sat outside my shed waiting as i got through a 406 then 407 project.
The first steps mainly in this video concern getting the Avantime started and running. By the end of the video it was running and a nasty ticking sound was cured with an oil flush and new oil.
The next videos will cover the removal of the engine, dealing with the rust on removable parts such as the subframe, rear axle and radiator support bar. With the engine out the timing belt and rocker covers will be addressed.
If you have any tips or advice regarding working on these Avantimes that is more than welcome.
Part 2 of this video: youtu.be/PeszR_vnfCg2019 Audi A3 1.6 TDI (EA288) Timing belt replacement - Fast OverviewpeugeotCitroen2CV2024-05-07 | A fast overview video, to see the original speed version view this video: youtu.be/CTT4fBOnl5s -------------------------------------------------------------------------------------------------------------------- The process of replacing the cam belt and water pump on a 2019 Audi A3 fitted with the EA288 1.6 TDI engine, badged in this instance as TDI 35. This is my cousins car which he bought recently but was weary about it needing a timing belt and asked me to change it. I ordered a set of locking tools on ebay for £20 and ebay also had service manual CD's which were quite useful to point out the important torque specs and the fact that audi state diagnostic equipment should be used to bleed the fuel filer and coolant system.
As far as belt changes go, the need for the diagnostic equipment and the maze of pipes sitting above the upper timing belt cover are a small annoyance although once in there its a fairly easy engine to work on.
It is worth noting however these 1.6 and the 2.0 do have a wet belt that drives the oil pump. My local motor factors say they rarely sell them, and speaking to some local mechanics it is not something they do. My uncle changed the wet belt on his 2.0 Touran with 160,000 miles so the next timing belt for this A3 it will get that wet belt changed. Although if anyone knows the official change interval it would be useful to know. The wet belt itself is not an expensive part but it does require the sump to come off, and the cover behind the crankshaft pulley has an integrated crankshaft oil seal which then must be replaced. Thankfully these do not suffer from the typical wet belt notoriety that the ford ecoboost or PSA puretech engines do.
For the diagnostic work in this video i used the Kingbolen Ediag Plus which is available from this link: amazon.co.uk/dp/B0CKYZKYKC
For any further questions feel free to ask in the comments below or message the facebook page for this channel: facebook.com/PC2CV
0:00 - Introduction 0:40 - Engine Undertray Removal 1:20 - Pipes in the way 5:15 - Coolant reservoir removal 6:00 - More pipes in the way 6:32 - Fuel filter housing 7:00 - The pipes, the pipes... 9:55 - Upper timing belt cover 10:40 - Wheel arch removal 12:30 - Draining old coolant 13:00 - Auxiliary Belt 13:35 - Crankshaft Pulley 14:00 - Placing jack under engine 14:15 - Engine Mount Removal 15:25 - Inner Engine Mount Removal 16:55 - Lower timing belt cover 17:33 - Turing engine to TDC 17:49 - Locking tool set 19:12 - Removing old belt 20:15 - Water pump removal 22:14 - Fitting new water pump 23:10 - Water pump bolts 24:02 - Idler Pulleys 24:20 - Replacing Studs 27:20 - Sprocket Information 29:34 - CAD explanation 30:35 - Torque Figures 30:50 - Installing new belt 31:30 - Setting belt tension 32:15 - Torquing Pulley Fasteners 32:58 - Turning engine over 33:25 - Checking locking pins 33:59 - Note on oil pump belt 34:14 - Lower cover 34:48 - Inner engine mount 35:22 - Engine mount install 36:22 - Upper Cover 36:59 - Effing Pipes Again 39:23 - Fuel filter housing 40:15 - Fresh Coolant 40:31 - Crankshaft pulley 40:55 - Auxiliary Belt 41:14 - Wheel arch liner 41:52 - Coolant Bleeding 45:25 - Service Stickers 46:13 - Engine Undertray 46:42 - ConclusionCitroen Berlingo B9 1.6 HDI DV6C (9HL) Fuel Injector Replacement v2peugeotCitroen2CV2024-05-06 | The process of resolving a faulty fuel injector on a 2011 Citroen Berlingo fitted with the 1.6 HDI 8 valve DV6C engine. In this instance that is engine code 9HL the 115 bhp variant with the Continental/Siemens fuel injection system.
This Berlingo previously had an engine replacement due to a snapped cam-belt, and its hard to be sure what injectors are original to it, nor do i know if past injectors were fitted with new copper washers and other hardware. It was clear to see when injector 4 was removed, in this instance injector 4 was the faulty injector. There was visible evidence that combustion gasses had been escaping as there was a buildup of carbon around the injector. This meant some cleaning was required before fitting a replacement injector.
Using a fault code reader, the berlingo threw up fault code P0271 Injector 4 control. Short-Circuit between two wires. The injector itself when inspected with a multimeter showed a significantly higher resistance reading than the other 3 injectors, the electronic component inside had failed. Although i will not claim to know any more about what goes on inside these injectors. If there are other tests or possible ways to fix these injectors DIY please mention in the comment section.
An important step to carry out if replacing an injector is to program in the code on top of the injector so that the ECU can be calibrated to work at its optimum with the injector fitted. In this case i entered the code for all 4 injectors as there were a couple not matching what was fitted to the engine. In this instance the Kingbolen Ediag Plus was used to carry out the programming operation, which is available from this link: amazon.co.uk/dp/B0CKYZKYKC
For any further questions feel free to ask in the comments below or message the facebook page for this channel: facebook.com/PC2CV2019 Audi A3 1.6 TDI (EA288) engine servicepeugeotCitroen2CV2024-04-29 | Carrying out a general engine service on my cousins 2019 Audi A3 1.6 TDI with the EA288 engine.
It seems a reasonably easy car to carry out a service on, although diagnostic equipment was required to correctly bleed the fuel system when the fuel filter was removed. I was following an Audi workshop manual pdf that i had sourced online which stated that diagnostic equipment was required.
In this instance i used the Kingbolen Ediag Plus to for that part of the job and it worked very well at doing that. A link for the device is below: amazon.co.uk/dp/B0CKYZKYKC
For any further questions feel free to ask in the comments below or message the facebook page for this channel: facebook.com/PC2CV
0:00 - Introduction 0:40 - Engine Undertray Removal 1:44 - Draining Oil 2:45 - Oil Filter 5:57 - Air Filter 8:36 - Fuel Filter 10:25 - Pouring Oil 11:29 - Bleeding Fuel System 13:04 - Service reminder reset 13:56 - Reinstalling Undertray 14:42 - Pollen Filter2019 Audi A3 1.6 TDI (EA288) Timing belt replacementpeugeotCitroen2CV2024-04-29 | The process of replacing the cam belt and water pump on a 2019 Audi A3 fitted with the EA288 1.6 TDI engine, badged in this instance as TDI 35. This is my cousins car which he bought recently but was weary about it needing a timing belt and asked me to change it. I ordered a set of locking tools on ebay for £20 and ebay also had service manual CD's which were quite useful to point out the important torque specs and the fact that audi state diagnostic equipment should be used to bleed the fuel filer and coolant system.
As far as belt changes go, the need for the diagnostic equipment and the maze of pipes sitting above the upper timing belt cover are a small annoyance although once in there its a fairly easy engine to work on.
It is worth noting however these 1.6 and the 2.0 do have a wet belt that drives the oil pump. My local motor factors say they rarely sell them, and speaking to some local mechanics it is not something they do. My uncle changed the wet belt on his 2.0 Touran with 160,000 miles so the next timing belt for this A3 it will get that wet belt changed. Although if anyone knows the official change interval it would be useful to know. The wet belt itself is not an expensive part but it does require the sump to come off, and the cover behind the crankshaft pulley has an integrated crankshaft oil seal which then must be replaced. Thankfully these do not suffer from the typical wet belt notoriety that the ford ecoboost or PSA puretech engines do.
For the diagnostic work in this video i used the Kingbolen Ediag Plus which is available from this link: amazon.co.uk/dp/B0CKYZKYKC
For any further questions feel free to ask in the comments below or message the facebook page for this channel: facebook.com/PC2CV
0:00 - Introduction 0:40 - Engine Undertray Removal 1:20 - Pipes in the way 5:15 - Coolant reservoir removal 6:00 - More pipes in the way 6:32 - Fuel filter housing 7:00 - The pipes, the pipes... 9:55 - Upper timing belt cover 10:40 - Wheel arch removal 12:30 - Draining old coolant 13:00 - Auxiliary Belt 13:35 - Crankshaft Pulley 14:00 - Placing jack under engine 14:15 - Engine Mount Removal 15:25 - Inner Engine Mount Removal 16:55 - Lower timing belt cover 17:33 - Turing engine to TDC 17:49 - Locking tool set 19:12 - Removing old belt 20:15 - Water pump removal 22:14 - Fitting new water pump 23:10 - Water pump bolts 24:02 - Idler Pulleys 24:20 - Replacing Studs 27:20 - Sprocket Information 29:34 - CAD explanation 30:35 - Torque Figures 30:50 - Installing new belt 31:30 - Setting belt tension 32:15 - Torquing Pulley Fasteners 32:58 - Turning engine over 33:25 - Checking locking pins 33:59 - Note on oil pump belt 34:14 - Lower cover 34:48 - Inner engine mount 35:22 - Engine mount install 36:22 - Upper Cover 36:59 - Effing Pipes Again 39:23 - Fuel filter housing 40:15 - Fresh Coolant 40:31 - Crankshaft pulley 40:55 - Auxiliary Belt 41:14 - Wheel arch liner 41:52 - Coolant Bleeding 45:25 - Service Stickers 46:13 - Engine Undertray 46:42 - ConclusionKingbolen Ediag Plus iPhone OBD fault code readerpeugeotCitroen2CV2024-04-22 | A review of the Kingbolen Ediag plus. An OBD fault code reader that works with iPhones over bluetooth, that can access all modules of modern vehicles to not only read fault codes but also carry out configurations, reset service lights reprogram certain features such as DPF regeneration or adding new parts and also live data. This combined with the ability to use the device wirelessly holding a phone outside the car whilst actuating specific components on the car make it very versatile.
From the 22nd April to the 29th April 2024 there is a 20% discount which will bring the price down to £114. That discount code is: HQUW3F9UCitroen C4 Picasso MK2 1.6 HDi DV6C - Service & Timing Belt ReplacementpeugeotCitroen2CV2024-04-09 | Carrying out a routine service then a timing belt and water pump replacement on a 2016 Citroen C4 Picasso fitted with the 1.6 HDi DV6C engine.
This car belongs to my aunt and to give her peace of mind it was booked in with me to carry out a full service and timing belt replacement. The engine is the same as fitted to a raft of other PSA vehicles including my old berlingo which i did this video on: youtu.be/toTKvACZiDE?si=v3JNDxe_BToTo7k9
The C4 Picasso is fairly easy to work on, there is plenty of room around the engine to access the main service items. As an overall package they are quite a nice car, the versatility of a berlingo with added refinement. The 1.6 feels like it has adequate power and the proper torque converter automatic gearbox gives a nice smooth relaxed driving experience unlike the earlier EGS automated manuals which are best avoided.
For any further questions feel free to ask in the comments below or message the facebook page for this channel: facebook.com/PC2CV
0:00 - Introduction 0:20 - Engine Undertray Removal 1:05 - Draining Engine Oil 1:45 - Oil Filter 2:57 - Air Filter 5:36 - Fuel Filter 9:31 - Filling Engine Oil 10:25 - Priming Fuel Filter 11:09 - Startup 11:51 - Timing Belt Section 12:10 - Wheel Arch Liner 13:35 - Supporting Engine 13:50 - Engine Mount 15:32 - Upper Timing Belt Cover 17:57 - Inner Engine Mount Bracket 18:47 - Lower Timing Belt Cover 19:28 - Auxiliary Belt 21:10 - Crankshaft Pulley 22:07 - Setting TDC 22:44 - Idler & Tensioner 23:10 - Crankshaft Position Sensor 23:25 - Removing Timing Belt 24:02 - Water Pump 25:40 - New Water Pump 26:10 - New Pulleys 27:12 - Installing New Belt 28:16 - Setting the Tensioner 29:10 - Turning Engine Over 29:50 - Lower Cover Reinstall 31:20 - Crankshaft Pulley Reinstall 31:48 - New Auxiliary Belt 32:38 - Inner Engine Mount 33:00 - Upper Timing Belt Cover 34:35 - Engine Mount 36:20 - Stickers 36:45 - Bleeding Coolant 39:57 - Refitting Wheel Arch Liner 41:00 - Undertray Reinstallation 41:16 - Service Light ResetHow to Diagnose/Replace a Heater Matrix on a Citroen C4 Picasso MK2: A Complete GuidepeugeotCitroen2CV2024-02-03 | Showing the process of diagnosing and then replacing a bad heater matrix on a 2016 Citroen C4 Picasso MK2. The Grand Picasso is obviously the same but i think given that the part number for the heater matrix is also used in a wide range of other PSA (and now stellantis) vehicles it could be an issue that others may have.
That part number for the heater matrix is: 9821299980 If you put that into google on its own, or prefix it with either PSA 9821299980, Citroen 9821299980 or Peugeot 9821299980 it should yeild a myriad of results.
Initially i noticed the heater issue myself, my aunt left the car with me in December 2023 for a cambelt change and service, i had to bleed the coolant when doing the water pump, in fact i flushed the old coolant. However i could not get the drivers side of the car to heat up. She had mentioned that the car took a long time for the cabin to heat up but it was like that the past year, The picasso still had a heater but only on the passenger side which explains why it took so long to heat up.
That allowed me to see the heater flaps cycle between hot and cold, i could see they were moving fine, but for added peace of mind i removed the stepper motors and moved the flaps by hand and they moved with no resistance which ruled that out.
The thermal camera showed that the heater matrix was hot on the passenger side, where the coolant goes in. However, on the drives side it was cold.
With the diagnosis complete i determined that the heater matrix was the issue and ordered the replacement from ebay.
The actual replacement is not too difficult, i would advise waiting for the car to be completley cold as you can see in the video even after 30 minutes of waiting there was enough pressure in the system to cause the coolant to shoot out. Let the system fully cool and also remove the coolant reservoir cap to release any pressure. Thankfully despite the mess of the coolant escaping it was not scalding hot so i was not injured. Obviously wash your face and hands after coming into contact with coolant and do not let pets near it.
The installation of the matrix was fairly straightforward, take your time to ensure the clips are properly attached and tightened as any issues there will cause leaks between where the pipes and heater matrix meet.
After the pipes are installed the coolant is bled, i used a Lisle 24680 spill free funnel kit: amazon.co.uk/Lisle-24680-Spill-Free-Funnel/dp/B00A6AS6LY?th=1 Ive had that for over 10 years now, a great kit but does not have an adapter for PSA cars, i took a coolant reservoir cap off a MK1 Citroen C5 diesel and drilled a hole through it which works well. The funnel means that new coolant is at the highest level in the coolant system and the weight of the coolant in the funnel pushes out any air, so when the bleed screws are open it rushes out. There are other ways with old bottles and lots of insulating tape but i do enough work around coolant systems to find this worth having.
Once the heater matrix was in, and the coolant bled the car was allowed to run for 15 minutes and the heater felt nice and warm on both sides. It improved even more once i drove the car on the road.
The old heater matrix was cut open with an angle grinder and it was clear to see the issue, it was completely bunged up with sludge at the far end, ie the side that was serving the drivers side. This prevented it from heating that side up.
Regarding the diagnostic device used in this video it was a Kingbolen ediag plus which is available from this link: amazon.co.uk/dp/B0CKYZKYKC
For any further questions feel free to ask in the comments below or message the facebook page for this channel: facebook.com/PC2CV
0:00 - Introduction 0:15 - Initial Diagnosis 2:40 - Drivers side heater flaps 5:00 - Passenger side parts 7:30 - Thermal imaging 8:20 - Heater Matrix Replacement 8:40 - New Heater Matrix 8:55 - Glovebox Removal 11:30 - Close to Heater Matrix 12:25 - Coolant Pipes 13:27 - Big Mistake 14:00 - Heater Matrix Removal 14:45 - Installing new Heater Matrix 14:10 - New o ring seals 15:30 - Connecting pipes to matrix 19:35 - Cleanup 20:10 - Bleeding Coolant 24:00 - Old Matrix Autopsy 24:52 - Reassembly 25:15 - Working Heater
#CitroenC4Picasso #HeaterMatrixReplacement #CitroenC4PicassoHeater #CarRepairTutorialTopdon JS3000 Review: Portable 12V Jump Starter & Power BankpeugeotCitroen2CV2024-02-01 | Topdon sent me their JS3000 portable jump starter to review, which I was eager to try as it is very useful when working around old cars. It’s also a modern jump starter that combines a high-capacity power bank, which is handy for charging modern smartphones, tablets, and laptops. On top of that, it has a very useful torch built into it.
I compare this with my older Snap-on Portable Power 1700, which is now something Portable Power sells directly, as Snap-on has a newer jump starter that is no longer made by Portable Power. The Snap-on is great at starting cars with no battery, whether it's for collecting old scrap or just working with cars that have no batteries. However, for most normal users, the JS3000, which costs less than half the price, is more than up to the task of starting vehicles with flat batteries.
I found the JS3000 quite impressive, particularly in terms of build quality and the features it packs, such as USB-C PD charging and an integrated torch. There are some downsides though, such as the fact that the leads have to be plugged into the side, which makes it bulky, and the 4 LEDs do not give the best resolution as to the battery's state of charge.
I am still using the jump pack mostly as a power bank for the phone when recording videos, but if you want to ask any other questions about it, feel free to ask here in the comments or via the Facebook page for this channel: facebook.com/PC2CV
This jump pack is available to purchase from the following link: amazon.co.uk/dp/B09XB8FFX5Peugeot 407 1.6 16v HDi DV6TED4 Turbo Oil Feed Pipe Replacement Including Turbo RemovalpeugeotCitroen2CV2023-12-27 | Replacing the turbo oil feed pipe on a Peugeot 407 fitted with the 1.6 16V 110bhp DV6TED4 engine. This car had a considerable oil leak coming from the turbo oil feed pipe unions on both sides, with the pipe noticeably loose where it met the unions. The pipe itself was fairly inexpensive, and the job took a couple of hours. It involved the removal of the turbo and DPF to access the point where the pipe attaches to the engine block. The copper washers, which seal the banjo bolts, were also replaced.
These engines are normally known for blowing turbos. However, this one, with over 180,000 miles, proves that with regular oil changes and the correct low SAPs oil, they can be reliable and economical powertrains, and not too challenging to work on. This engine is fitted to a wide variety of PSA (Peugeot Citroën) vehicles, including the Peugeot 206, 207, 307, 308, 3008, 5008, and Partner, as well as Citroën C2, C3, C4, C5, and Berlingo. Additionally, Ford and its subsidiaries at the time, such as Fiesta, Focus, Transit Connect, Volvo V40, and Mazda 3, to name a few, all used this engine.
I was also changing the alternator at the same time, which was why the air conditioning pump and alternator were removed. This provided better access to some of the DPF bolts, but it should still be possible to do the job with them in place, although access was definitely improved.
The owner of this car was very glad to get it back on the road, as he was forced to drive a Toyota Avensis, which had a lot more problems than this 407: a slipping clutch, bad brakes, a heater that did not work, and it was in limp mode. It also struggled to achieve 40mpg, while this 407 generally averages 50mpg and above. In total, the 407 received a timing belt kit replacement, a replacement alternator, and a turbo oil feed pipe to put it back into daily service.
For more in-depth questions, feel free to contact us via Facebook. The page for this channel is available at: facebook.com/PC2CV
0:00 - Introduction 0:30 - Undertray Removal 1:00 - Boost Pipes Removal 1:44 - DPF Removal 4:00 - Intake Pipes Removal 6:50 - Vacuum Pipe Removal 7:05 - Turbo Oil Return Line 7:20 - Turbo Oil Feed Pipe Bolt 7:45 - Removing turbo fasteners 9:30 - Removing the turbo 9:55 - Removing turbo oil feed line 10:25 - Installing new turbo oil feed line 11:05 - Reinstalling the turbo 11:25 - Installing turbo oil feed pipe 13:50 - Reinstalling turbo oil drain pipe 14:05 - Reinstalling vacuum pipe 14:20 - Reinstalling DPF 18:25 - Reinstalling turbo piping 20:40 - Turning engine over 21:05 - Reinstalling Engine UndertrayPeugeot 407 1.6 16v HDi Alternator ReplacementpeugeotCitroen2CV2023-12-27 | Replacing the alternator on a Peugeot 407 fitted with the 1.6 16v HDi DV6 engine. This process should be the same or very similar for most PSA cars (and Ford group cars) fitted with this engine. That includes the 206, 207, 307, 308, 3008, 5008, Partner, Citroën C3, C4, C5, Berlingo. I also think the Ford Focus, Mazda 3, Volvo V40, to name a few, are similar.
It is a relatively straightforward job, although it is much easier if you have a lift, but should be doable on axle stands. A replacement alternator from a local scrapyard cost £25.
I was doing the timing belt and also had to remove the turbo to replace the oil feed pipe on this car, but it was all relatively easy to work on.
This car belongs to a friend of a friend; it had been off the road for over 6 months due to the failed alternator. It was a car that was used quite a lot and was sorely missed as the owner had a 2007 Toyota Avensis which was nearly done, with much more serious and expensive issues compared to this 407, and it was also significantly thirstier on diesel, so he was keen to get his economical 407 back on the road.
For more in-depth questions, feel free to contact via Facebook. The page for this channel is available at: facebook.com/PC2CVMercedes W205 C Class Brake Disks & Pads ReplacementpeugeotCitroen2CV2023-12-26 | The process of replacing the brake pads and front disks on a W205 Mercedes C Class. This car is a 2015 model and belongs to my dad. He had been complaining that the car was showing a 'replace brake pad' message on the instrument cluster. As it turned out, the rear pads were quite thin, to the point where the rear wear sensor was worn through. However, the disks were still fine, so they were not changed. On the front, there was a lip on the inner edge of the inside pads caused by a corrosion lip on the inner edge of the disks. The disks themselves were still above the minimum thickness and not worn, so I had a friend put them on his lathe to remove the lip.
It is not the hardest brake job to do; however, you do need diagnostic equipment to put the handbrake into service position, and a rewind tool to push the rear caliper pistons in to create the clearance required for the new pads. In addition to that, a snapped locking wheel bolt key did add to the hassle a bit.
For more in-depth questions, feel free to contact via Facebook. The page for this channel is available at: facebook.com/PC2CVPSA 1.6 8v HDi (DV6C) Full DisassemblypeugeotCitroen2CV2023-12-25 | Taking apart a DV6C engine to see what was causing it to knock badly. This engine came from my friend's Citroën Berlingo. The engine had been fine, but it was remapped a week before the noise started, so that is what this has been attributed to, as these engines are generally very reliable. This is the first one out of the many that power vehicles owned by friends or relatives that has done this.
In the end, the engine suffered a spun bearing on the big end nearest to the timing belt. It would have needed a set of bearings, a conrod, and a crankshaft.
It worked out handier to buy a scrap C4 Picasso with a good engine than to consider rebuilding this one.
My friend left this engine with me after another mechanic did the engine swap for him. I was interested to see what caused this engine's noise, but also wanted the opportunity to fully disassemble one of these engines. My friend is able to sell the ancillaries, and I got to keep a jar of all the nuts and bolts removed from this engine, which can be very handy when working on cars to have spare.
This is not so much a definitive guide on how to take one of these engines apart. I'm not sure I went about the process in the most efficient manner, and certainly did not follow any specific sequences for untightening bolts for the camshaft carrier or head, which would be important to follow if rebuilding the engine. However, it should hopefully show where everything is and what inside these DV6C engines looks like.
If you want to get the proper torque specs and disassembly guides for one of these engines, a Haynes manual is a good point of reference. Alternatively, ServiceBox, which is PSA's online portal for parts diagrams and official workshop guides, will have the required information. public.servicebox.peugeot.com
If you register there and pay for 1 hour's membership, which is under €10, you can view and print any documents you need that at least provide the information directly from the manufacturer. eBay also has workshop manuals and service guides.
For more in-depth questions, feel free to contact me via Facebook. The page for this channel is available at: facebook.com/PC2CV2020 Citroen C3 Aircross 1.5 HDI Engine ServicepeugeotCitroen2CV2023-12-18 | Servicing a 2020 Citroen C3 Aircross fitted with the 1.5 BlueHDI (YHY) Engine. It was getting an oil change, new oil filter, air filter, and fuel filter.
This is very similar to the older 1.6 8v DV6 engine fitted to most PSA Cars, however, the fuel filter location is different with it being located under the car in front of the rear wheel. While it might be a nuisance for someone using axle stands, I personally found this a better arrangement compared to the older engine. The filter is actually easier to remove (despite needing a 19mm hex socket or M12 bolt to undo the fuel filter housing lid), it was an easy filter to change and the priming procedure was made very simple due to the fact there was an in-tank fuel pump.
It is still quite an easy car to service, not too sure exactly what the parts cost as my friend who owns the car supplied them in the boot but I would imagine it is all similar to the older engine.
For more in-depth questions feel free to contact via Facebook. The page for this channel is available at: facebook.com/PC2CVRenault Kadjar Door handle keyless entry button replacementpeugeotCitroen2CV2023-12-17 | The process of replacing a door handle keyless entry button on a 2017 Renault Kadjar I think the Renault Captur is similar, and there is a chance the Qashqai uses something similar.
Keyless entry is a convenient feature, particularly for my cousin, the owner of this car. With young children, being able to access the car hands-free is immensely helpful. Unfortunately, this feature ceased functioning, which was a noticeable inconvenience.
I opted to purchase a complete replacement handle from eBay for this repair. While more intricate solutions like soldering a new microswitch or using 3D printing to adapt an alternative switch were considered, time constraints due to my upcoming return to university for a master's degree limited my options.
Filmed in September 2022, this footage remained unedited until now, December 2023. The replacement process is straightforward – the issue typically lies with a worn-out microswitch. The new switch has been operational without issues since its installation.
I still have the old switch and intend to explore potential modifications when time permits.
For further detailed inquiries related to this topic or other car-related questions, feel free to visit the PeugeotCitroen2CV Facebook page at: facebook.com/PC2CVNissan Qashqai R9M 1.6 DCI Timing Chain ReplacementpeugeotCitroen2CV2023-11-07 | How to replace the timing chain on a 2013 Nissan Qashqai J10 fitted with the 1.6 DCI R9M engine.
This Qashqai had a rattling noise coming from the engine, hard to get the camera to pick it up over the clatter of the diesel but it was pronounced and there was also an engine management light on with codes related to the camshaft being out of synchronisation.
This car had less than 85,000 miles and it is quite disappointing that the chain was already showing signs of wear like this. However it possibly may be down to the wrong oil being used, or services being skipped. My mate just bought the car and wanted to leave it right, hopefully with this new chain and a more rigorous service schedule the new chain should last much longer.
The R9M engine is one that was developed as part of the Renault/Nissan alliance and it seems to have replaced an older 2.0 engine. It is not the same as the smaller 1.5 DCI K9K belt driven engine. Also the 2.0 M9R engine although its timing locking tools look similar they will not work here.
The R9M is used in a wide range of vehicles that are part of that group, also some badge engineered vehicles and Mercedes also use it in some of their vehicles. The list includes but is not limited to:
- Nissan Qashqai (J10 and the newer J11) - Nissan X-Trail - Renualt Megane - Renault Scenic - Renault Kadjar - Renault Tailsman - Mercedes A Class - Mercedes C Class - Vauxhall / Opel Vivaro - Nissan Primastar - Renault Trafic
The Qashqai is a tight engine bay, the worst aspect of this job is the fact the way to lock the crankshaft is via a hole located behind the starter. I have heard some mechanics can do it without removing the starter and just use tippex or marks. However being the first R9M and timing chain i have done i did not want to take any chances and followed the nissan workshop manual. If i had another engine from a scrapyard to hand i would try to design a tool to lock the crankshaft at the timing chain side by indexing some of the bolt holes for the timing chain cover. However my mate needed this car back in a hurry so i did not have the time to design or 3D print and test a tool.
For any more in depth questions or ones that need photos/diagrams to be sent feel free to send a message on my facebook page: facebook.com/PC2CVCitroen C4 Picasso Heater Blower Resistor ReplacementpeugeotCitroen2CV2023-10-10 | Fixing a 2016 Citroen C4 picasso with a heater blower motor that is stuck on at full speed.
The problem here is that the resistor unit or control unit for the motor has failed and is holding the fan on at full speed, sometimes when these fail some speeds will not work, the motor might not work at all or it is stuck on at full speed regardless of the setting on the dash or even if the ignition is turned off.
Thankfully the part itself is very easy to get to and being commonly used across a wide range of cars in the PSA (and it seems also the Stellantis) range it is easy to get a replcement fairly cheaply.
The part in this instance is A43002900, it is best to start your search on google and work from there. Scrapyards with PSA vehicles in stock should be able to do it fairly cheaply. The replacement only cost £20 which was very reasonable
For any more in-depth questions, ask on the Facebook page: facebook.com/PC2CVPeugeot 308 1.6 HDi Service and Eolys/Pat fluid pump replacementpeugeotCitroen2CV2023-10-08 | Servicing a 2012 Peugeot 308 1.6 HDi with the 1.6 HDi 8v DV6C engine.
This is a car my cousin uses. It has had the "Engine Fault, Risk of Particle Filter Clogging" message come up due to a faulty additive pump. Sometimes that fault will come because the additive tank is empty, but in this case, the pump itself had developed a fault. The replacement is shown in this video.
A replacement pump was sourced from another 2012 308 at a local scrapyard for £40, and a bottle of PAT fluid from a local motor factors was £40. I think the kit for the PAT fluid bottles, which allows you to fill the additive tank, was £20 - it was something I got a few years ago. Additive pumps seem to demand a lot more on eBay, with prices over £100 to £300 for new ones. One reason why local scrapyards are still worth visiting is the value and being able to check the car it came from to see if it shows the same fault.
I took a bit of a shortcut when it comes to fitting the replacement additive tank, snipping away the plastic that holds it to the tank. This avoided the need to drop the tank. Frankly, that is a poor design choice to necessitate that. I used a cable tie to hold it back up and, combined with the other parts in the way, it is sufficiently secure and is not rattling.
A few other items were attended to; the car was given a basic service and some bulbs around the back were replaced.
For any more in-depth questions, ask on the Facebook page: facebook.com/PC2CV
Music provided by Bensound: Music: bensound.com License code: 2JYZXWGRNXVW3TAE
0:00 Introduction 0:38 Undertray Removal 1:10 Draining Oil 2:15 Refitting Undertray 2:25 Additive Tank Location 4:36 Fault Verification 5:45 Oil Filter Replacement 7:10 Air Filter Replacement 9:10 Fuel Filter Replacement 11:56 Filling New Oil 12:45 Startup 13:43 Service Reminder Reset 14:05 Fault Message 14:15 Refilling Eolys Fluid 15:39 Fitting new additive tank 16:44 OBD Diagnostic work 22:10 Installing new tank 24:20 Number plate light bulb 24:38 3rd Brake light bulbsCitroen C4 B7 Front Strut:Shocks ReplacementpeugeotCitroen2CV2023-10-01 | Replacing the front shocks in my 2012 Citroen C4
This should be the same as a 308 of the same age and the DS4 is near enough identical to this C4.
I went back to uni to do a masters this year and this C4 has been what i bought before i started for some cheap motoing. Have to say these are a great car if you want something modern that is reliable and easy run. It has always had a bit of a clunk in the front end, last september i changed the front wishbone bushes, anti roll bar bushes, droplinks, lower balljoints, track rod ends and strut top bearings. These struts were the only thing left to do and seem to have made the most difference. Despite that sounding like a long list of items it didnt really cost too much and only took a few hours to fit, these cars are a doddle to work on and despite the simple suspension are very comfortable and great on a ling run.Topdon TC004 Thermal Imaging CamerapeugeotCitroen2CV2023-05-31 | A Review of the Topdon TC004 thermal imaging camera.
It is something i have been interested in getting for a few years now as their applications around cars, electronics or heating systems seems very useful.
This device was sent to me by Topdon to do a review on it despite it being sent for free i have remained as impartial as i can be. Having said that i think it does the job very well and produces a usable image that can be very handy in a wide range of diagnostic applications.
Unfortunately the deeper i got into the avantime the worse its condition appeared. In the end a decision was made that the car was beyond economic repair and its owner took it back to sell parts from it.
------------------
Credit for the soundtrack used: Airport Lounge - Disco Ultralounge by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0
Artist: http://incompetech.comRenault 70 14 Tractor Battery ReplacementpeugeotCitroen2CV2022-09-16 | ...Peugeot 407 front abs faultpeugeotCitroen2CV2022-09-15 | ...Peugeot 407 Windscreen washer jets repairpeugeotCitroen2CV2022-09-15 | ...Citroen C4 clicking check strap and squeaky window fixpeugeotCitroen2CV2022-09-14 | ...Citroen C4 wobbly mirror repairpeugeotCitroen2CV2022-08-29 | Fixing the wobbly drivers door mirror on my 2013 Citroen C4 hatchback.
A simple but quite irritating issue, the mirror wobbled when driving along which did affect how the image was shown in the mirror. The motor on the mirror sits down on the spindle on the door, for whatever reason it had developed clearance, quite possibly the screw worked loose over time. A bit of tape on the spindle and firm press down plus tightening the screw seemed to resolve the issue.Citroen Berlingo front seatbelt removalpeugeotCitroen2CV2022-07-17 | ...Citroen Berlingo Rear Brakes and Rear Axle RemovalpeugeotCitroen2CV2022-07-09 | Removing the rear brakes and rear axle from a 2011 Citroen Berlingo B9
The axle is scrap due to the accident damage, however the rear callipers and perhaps the rear disks may still be of use as spares for another berlingo, possibly even the C4 that has replaced this berlingo. The video shows how to remove the rear axle which may be useful if the rear axle bushes need to be replaced.
For any questions ask in the comments or alternatively visit the facebook page for this channel and send a message: www.facebook.com/PC2CVCitroen Berlingo Modutop Roof RemovalpeugeotCitroen2CV2022-07-03 | Removing the optional modutop roof fitted to a 2011 Citroen Berlingo B9. This option was available on all B9 Berlingo Multispace and Peugeot Parter Tepees. The older shape berlingos also had it as an option, it seems to be more common on them, although arranged slightly differently.
Rather than let this get scrapped i have removed all the parts that constitutes the modutop kit, i do not know if i will have another berlingo but its an option to fit it into a multispace without this roof, or give it so someone who wants to do the conversion.
0:00 Introduction 0:30 A pillar trim 0:40 B pillar trim 3:02 C pillar trim 3:17 D pillar trim 3:30 Rear storage bin 6:40 Rear seatbelt trim 7:28 Centre overhead console 10:06 Front storage shelf 12:45 Overhead fan unit 14:20 Rear storage nets 15:55 Central headlining 16:20 Roof bars 16:57 Headlining 17:32 Roof panel bolts 18:03 Radio Aerial 18:43 Roof panel removal 20:55 Lifting off roof panelCitroen Berlingo / Peugeot Partner B9 Dashboard RemovalpeugeotCitroen2CV2022-06-29 | One way, possibly not the most direcOne way, possibly not the most direct way of removing the dashboard from a Citroen Berlingo or Peugeot Partner B9. I am not aware of these berlingo having an inherent heater matrix issue, nor do i know if the dash needs to come out to remove it. Not too sure if there are many reasons to remove the dash on a berlingo but as i was breaking this one down entirely before sending it off for scrap here is the removal of the dashboard.
Time stamps have been provided so you can go to specific sections if required.
0:00 Introduction 0:14 A pillar trim around bonnet release handle 1:20 A pillar trim on drivers side 1:28 Passenger airbag deactivation switch 1:45 Electric mirror and headlight aim switch 2:20 Front carpet 2:32 Glovebox 3:06 Passenger Airbag 4:15 Steering wheel 5:00 Steering cowl trim and stalks 6:15 Steering column universal joint 7:18 Instrument cluster 7:55 Storage box behind instrument cluster 8:30 Immobiliser ring and key barrel 9:55 Steering column 11:35 Gearstick and central components 12:50 Central LCD screen 13:04 Heater control panel 14:18 Gear linkage cables 16:06 Airbag ECU 16:57 Dashboard Tweeters 17:12 A pillar windscreen trims 17:54 Dashboard to bulkhead bolts 18:20 Dashboard Removal 18:58 HVAC unit removal 21:15 Accelerator Pedal 21:45 Clutch Slave Cylinder 22:30 Pedal Box Assembly 23:10 Brake Pedal Switch 23:22 Connection to brake servo 23:42 BSI Removalt way of removing the dashboard from a Citroen Berlingo or Peugeot Partner B9. I am not aware of these berlingo having an inherent heater matrix issue, nor do i know if the dash needs to come out to remove it. Not too sure if there are many reasons to remove the dash on a berlingo but as i was breaking this one down entirely before sending it off for scrap here is the removal of the dashboard.
Time stamps have been provided so you can go to specific sections if required.
0:00 Introduction 0:14 A pillar trim around bonnet release handle 1:20 A pillar trim on drivers side 1:28 Passenger airbag deactivation switch 1:45 Electric mirror and headlight aim switch 2:20 Front carpet 2:32 Glovebox 3:06 Passenger Airbag 4:15 Steering wheel 5:00 Steering cowl trim and stalks 6:15 Steering column universal joint 7:18 Instrument cluster 7:55 Storage box behind instrument cluster 8:30 Immobiliser ring and key barrel 9:55 Steering column 11:35 Gearstick and central components 12:50 Central LCD screen 13:04 Heater control panel 14:18 Gear linkage cables 16:06 Airbag ECU 16:57 Dashboard Tweeters 17:12 A pillar windscreen trims 17:54 Dashboard to bulkhead bolts 18:20 Dashboard Removal 18:58 HVAC unit removal 21:15 Accelerator Pedal 21:45 Clutch Slave Cylinder 22:30 Pedal Box Assembly 23:10 Brake Pedal Switch 23:22 Connection to brake servo 23:42 BSI RemovalCitroen Berlingo B9 Engine RemovalpeugeotCitroen2CV2022-06-25 | The process of removing the engine, and generally removing as many front end components from my written off 2011 Citroen Berlingo 1.6 HDi.
Given i have removed more than what was necessary for just an engine removal process, you can decide what you may not need to remove if doing a similar job. This will hopefully give an overview of how the various parts come off.
0:00 Introduction 0:20 Lifting front end 1:20 DPF / Catalytic Converter Removal 7:34 Turbo Removal 9:50 Battery Removal 10:06 Fuse box removal 14:10 Battery tray removal 16:25 Reverse switch disconnection 17:00 Clutch slave cylinder 17:38 Earth cable 17:50 Heater matrix hoses 18:18 Gear linkage cables 19:52 Gearbox oil 20:22 Fuel Filter 20:46 Front suspension 23:34 Driveshaft clamp 24:55 Brake servo vacuum line 25:13 Scuttle panel and wipers 30:41 Front struts 31:26 Lower radiator support bar 32:10 Bonnet 32:20 Lower rear engine mount 33:10 Subframe 40:40 Attaching lifting chain 41:19 Unbolting engine mounts 42:48 Engine removal 43:48 Gearbox removalCitroen Berlingo Rear Sliding Door RemovalpeugeotCitroen2CV2022-06-11 | ...Citroen Berlingo front door disassembly and removalpeugeotCitroen2CV2022-06-10 | ...Citroen Berlingo Front End RemovalpeugeotCitroen2CV2022-06-08 | ...Citroen Berlingo Rear Bumper RemovalpeugeotCitroen2CV2022-06-01 | ...Citroen Berlingo Multispace / Peugeot Partner Tepee Rear Tailgate RemovalpeugeotCitroen2CV2022-05-30 | The first in a series of disassembly videos of my old 2011 Citroen Berlingo Multispace XTR. I was allowed to buy it back from the insurance company for spare parts so it seemed like the ideal way to get some more Berlingo content on the channel.
The berlingo is now fully stripped any video content has been recorded but not yet edited. At this stage the vast majority of parts are away.Citroen C4 ABS FaultpeugeotCitroen2CV2022-04-28 | ...Topdon Artidiag 600s - a reviewpeugeotCitroen2CV2022-04-01 | Having a look at a Topdon Artidiag 600s fault code reader.
They sent me one to keep in exchange for a review. It seems to be quite a good machine for its price. While it lacks the ability to go into things such as HVAC systems, the BSI on Peugeot/Citroens to change configurations such as adding cruise control for most DIYers it will be more than up to the task of finding out why an engine management, airbag or ABS fault light has come on. Those are the main dashboard lights that will cause an MOT failure so this covers those main areas.
Despite this being the executive model it came with what seems like a fairly meagre sound system. A 406 executive got an uprated JBL setup which was a good sounding system in its day, the speakers never had this issue on a 406.
Thankfully a set of pioneer speakers cost less than £100 to buy and the process is fairly DIY friendly. A set of new door clips is handy to have as some will inevitably break.
A new head-unit and amplifier might be the way to go for some bass heavy beats, however the design of the 407 dash with the climate control system being integrated into the infotainment system limits available choices to cheap tat from alibaba which reading through forums and owners clubs seems to be prone to a sleuth of irritating niggly issues.Peugeot 407 Floppy Indicator Stalk RepairpeugeotCitroen2CV2022-01-24 | ...Peugeot 407 front disks and pads replacementpeugeotCitroen2CV2022-01-01 | A very quick and brief video showing the replacement of the front disks and pads on a 2006 Peugeot 407. Not the usual level of detail here, mostly without subtitles but its quite a simple process a basic tool kit should have all the sizes of sockets and spanners needed to do this job.
Peugeotcitroen2cv facebook page facebook.com/PC2CVPeugeot 407 Rear Brakes & Central Console RemovalpeugeotCitroen2CV2022-01-01 | How to remove the rear backplates on a Peugeot 407.
This job involves removing the rear brake disks, pads and callipers which also involves removing the centre console to access the handbrake release mechanism. Plenty covered for various 407 related repairs.
If you have any questions feel free to get in contact via facebook.com/PC2CVMercedes W205 C class C220 C250d servicingpeugeotCitroen2CV2021-12-30 | Carrying out a quick service on a 2015 Mercedes W205 C220d
The oil, oil filter, air filter, fuel filter and cabin dust filter are replaced, along with the service reminder reset.
Most of the service items were bought from a local Mercedes dealer, as with most modern diesels its worth getting the exact oil specified by the manufacturer and the oil was not too expensive. The air and oil filters were not too bad. Only the fuel filter was bought from a local motor factors. £30 for a Bosch item or £80 from Mercedes for something that is probably no better quality than a Bosch item.
In general this car is not too hard to service, everything is easy to access and sensibly laid out.Peugeot 407 drivers side heater flap fixpeugeotCitroen2CV2021-12-27 | How to fix a broken heater flap on a Peugeot 407. This problem seems to be very common on the 407, its more a question of when it will break rather than if. Dealers will want to remove the dash and most mechanics will not want to do this job. However if you set a few hours aside its something that can be done DIY. A bit messy and fiddly but it is a repair that i have now done on several 407 and it has continued to work well.
Facebook page for this channel if you have any questions facebook.com/PC2CVPeugeot Citroen flip key repairpeugeotCitroen2CV2021-11-26 | A link to the STL file for the jig if you wish to 3D print one. prusaprinters.org/prints/108494-peugeot-citroen-flip-key-pin-removal-jig407 Rust Protection TreatmentpeugeotCitroen2CV2021-11-24 | One attempt to protect the underside of a car from rust. As my experience at this is fairly limited i decided to do it on a fairly cheap car a 2006 Peugeot 407 2.0 Executive.
I did the same process 2 years ago on a Honda jazz although that video was not as detailed as this youtu.be/ecG4PZIYZoo
I learnt most of what i could by reading articles in practical classic/car mechanics magazine, the website rust.co.uk was highly recommended and has great informative articles on the subject. It seems crucial to have the underside of the car as clean as possible, clean of grease and oils, have any salt neutralised before then going on to remove the rust and bring it back to bare metal.
Bilt hamber underbody and cavity waxes were used in the case of this 407 as they had more favourable postage costs to Northern Ireland. I am not a big fan of waxoyl as it tends to be slopped around the underside of a car being sold by some unscrupulous type to get rid of a problem. The jazz actually has one corner of a wheel-arch that was treated with the stuff after i left it to a bodywork place to have part of the sill welded. The rest of the car is resisting corrosion quite well but the waxoyl has lost its adhesion to the metal.
facebook.com/PC2CVPeugeot 407 Rear ABS sensor replacementpeugeotCitroen2CV2021-11-21 | This 2006 Peugeot 407 was displaying ABS and ESP warnings on the central infotainment screen and the instrument cluster screen, as well as an ABS light on the instrument cluster. As a result of there being an ABS fault the speedometer would not display the cars speed, the cruise control and speed limiter did not work and the sat nav also refused to work.
Plugging in a fault code reader it was determined that the rear ABS sensors were faulty.
In this video i go to the extreme of actually removing the fuel tank to change the sensors, the reason the tank is removed is that the wires for the sensors sit in tracks moulded into the top of the tank, and the connectors are located above the tank. I was giving the underside of this car a full rust protection and have videos to make so choose the longer route.
It is i believe possible to change the sensors but just lowering the tank slightly. I have a spares 407 estate which will feature in videos later on and i will try to find out then if it is possible to change the sensors without dropping the tank.
facebook.com/PC2CVPeugeot 407 Front bumper and front panels removalpeugeotCitroen2CV2021-11-16 | This video began with the intention of fixing a slightly damaged radiator grille but went as far as to remove the headlights to polish them and spray the front end with Bilt Hamber rust protection wax. As this car is getting a bit of a 'tidy up' it had a replacement undertray fitted using riv nuts to replace the questionable fixtures that were used originally. Also covered in the video is the removal of the front wings, the slam panels and the under-bonnet lining from the spares 407 bought to donate this 407 some parts and possibly for some videos in the future.
facebook.com/PC2CVCitroen Berlingo : Peugeot Partner B9 front brakes & brake fluid flushpeugeotCitroen2CV2021-10-24 | Changing the front disks and pads on a 2011 Citroen Berlingo B9.Peugeot 407 2.0 HDi Timing Belt ReplacementpeugeotCitroen2CV2021-10-16 | How to replace the timing belt on a Peugeot 407 fitted with the 2.0 16v HDi engine engine code DW10BTED4. This is the first time i have carried this job on any 2.0 16v engine and took a few steps that came from memories of working on the old 2.0 8v from the 406. The newer engine is arranged differently with an idler pulley being located in the lower section of the engine mount bracket. The fuel pump also is not driven by the cambelt, but instead it has been moved to the other side of the engine and seems to be driven via the camshaft.
Generally it is not too hard to replace the belt on this engine, the drain bolt at the back does not need to come off, you can flush the coolant well enough via the bleed screws. The fact the starter needs to come out to access the hole to lock the flywheel is a hassle, if the hole had been elsewhere on the block it may have been possible to do it without removing components but then the timing belt is not due for at at least another 6 years.
Regarding the timing belt interval, i do not have the exact information to hand but it usually is in the maintenance handbook that comes with the car. A document that is suprisingly hard to find in PDF form to confirm. However online searches seem to suggest the interval for a 2.0 hdi with a particle filter is All HDi engines without particle filter: 120 000 km (70,000 miles) or 6 years All HDi engines with particle filter: 180 000 km (110,000 miles) or 9 years
This video is specific to the 407, although the same engine was fitted to other PSA cars such as the Citroen C5 MK1 facelift and MK2, the 307, 308, Dispatch/Relay, 607. Ford i belive used the engine in the Mondeo, and Volvo in a few of their cars from this era.