Uploaded October 2026 | Updated November 2026, 3 hours ago
Before I put a motor in a rocket, I run five checks on it. If any one of them is bad, the rocket does not fly. In this video, Tim opens RockSim and walks through the five numbers he checks on every design before it goes to the launch field: static margin, lift-off speed, weathercocking, deployment speed, and fin flutter.
You'll see where each number lives in the simulation results, what value to look for, and what to change when the number comes back bad. You'll also see the weathercocking cone in the 2D flight profile, the green/red dot that RockSim Pro puts on the flight, and how the last number in a motor's name (the delay) sets your parachute deployment speed.
WHAT YOU'LL LEARN IN THIS VIDEO:
- How to read the static margin (center of gravity vs. center of pressure) — and why 1 or higher is what you want
- Why the rocket needs at least 30 mph (44 ft/s) by the time it leaves the launch rod — and how a longer launch rod or a higher-thrust motor fixes a slow lift-off
- How to check weathercocking in the 2D flight profile and keep the apogee point inside the weathercocking cone
- Why 50 mph is the limit for parachute deployment — and how swapping a C6-5 for a C6-7 or a C6-3 changes that speed
- What fin flutter is, why fins can come off at high speed, and how to keep a 25% fin safety margin
- The order to check all five in, and how to keep changing motors and parts until all five come back good
KEY TERMS:
- Static Margin: The distance between the center of gravity and the center of pressure, divided by the body tube diameter. A margin of 1 or higher means a solidly stable rocket.
- Center of Pressure (CP): The point where all the aerodynamic forces on the rocket balance — where lift and drag act.
- Weathercocking: The rocket turning into the wind as it climbs. A little is normal; too much sends the rocket sideways instead of up.
- Velocity at Launch Guide Departure: The rocket's speed the moment it clears the launch rod — the speed the fins need in order to steer.
- Fin Flutter: The fin oscillating (flapping) itself apart at high speed. The fin safety margin is how much room you have below the critical flutter speed.
FAQ:
Q: What is the minimum static margin for a model rocket?
A: Anything above zero is technically stable, but Tim's rule of thumb is 1 caliber or higher. Short, stubby rockets tend to have a lower margin; long rockets naturally have more.
Q: How fast should my rocket be going when it leaves the launch rod?
A: 30 mph (44 ft/s) is the minimum Tim looks for. Below that the fins cannot correct the rocket, and it wobbles or weathercocks. Fix it with a longer launch rod or a higher-thrust motor.
Q: How do I lower my parachute deployment speed?
A: Choose a shorter motor delay. The last number in a motor name is the delay in seconds — a C6-5 waits 5 seconds after burnout, while a C6-3 opens the parachute 2 seconds earlier. The time you need depends on the rocket and the weather conditions. This is tricky, which is why you need a program like RockSim
Q: What is fin flutter, and how much margin do I need?
A: Flutter is the fin oscillating until it fails. RockSim calculates the critical flutter speed for your fins, and Tim keeps a 25% safety margin below that number.
PRODUCTS USED IN THIS VIDEO:
- RockSim Flight Simulation Software: apogeerockets.com/Rocket_Software/RockSim?utm_source=youtube&utm_medium=description
RELATED RESOURCES:
- How to Calculate and Optimize Your Rocket's Minimum Lift-Off Speed (Peak-of-Flight #683): apogeerockets.com/Peak-of-Flight/Newsletter683?utm_source=youtube&utm_medium=description
- Model Rocket Stability (Peak-of-Flight #462): apogeerockets.com/Peak-of-Flight/Newsletter462?utm_source=youtube&utm_medium=description
- How Windy is Too Windy for a Launch? (Peak-of-Flight #498): apogeerockets.com/Peak-of-Flight/Newsletter498?utm_source=youtube&utm_medium=description
- Venting Ejection Charges, Selecting Ejection Delays (Peak-of-Flight #520): apogeerockets.com/Peak-of-Flight/Newsletter520?utm_source=youtube&utm_medium=description
- Fin Flutter Analysis Revisited (Again) (Peak-of-Flight #615): apogeerockets.com/Peak-of-Flight/Newsletter615?utm_source=youtube&utm_medium=description
- Your First Rocket Club Launch: The No-Embarrassment Checklist (Video #468): apogeerockets.com/Advanced_Construction_Videos/Rocketry_Video_468?utm_source=youtube&utm_medium=description
Subscribe to the Apogee Components channel for weekly rocketry build videos, and visit apogeerockets.com to learn, shop, build, and fly!
#modelrockets #modelrocketry #howtomakeamodelrocket #RockSim
---
Free newsletter - new rockets, techniques and free plans: apogeerockets.com/Newsletter-Subscribe?utm_source=youtube&utm_medium=description
Before I put a motor in a rocket, I run five checks on it. If any one of them is bad, the rocket does not fly. In this video, Tim opens RockSim and walks through the five numbers he checks on every design before it goes to the launch field: static margin, lift-off speed, weathercocking, deployment speed, and fin flutter.
You'll see where each number lives in the simulation results, what value to look for, and what to change when the number comes back bad. You'll also see the weathercocking cone in the 2D flight profile, the green/red dot that RockSim Pro puts on the flight, and how the last number in a motor's name (the delay) sets your parachute deployment speed.
WHAT YOU'LL LEARN IN THIS VIDEO:
- How to read the static margin (center of gravity vs. center of pressure) — and why 1 or higher is what you want
- Why the rocket needs at least 30 mph (44 ft/s) by the time it leaves the launch rod — and how a longer launch rod or a higher-thrust motor fixes a slow lift-off
- How to check weathercocking in the 2D flight profile and keep the apogee point inside the weathercocking cone
- Why 50 mph is the limit for parachute deployment — and how swapping a C6-5 for a C6-7 or a C6-3 changes that speed
- What fin flutter is, why fins can come off at high speed, and how to keep a 25% fin safety margin
- The order to check all five in, and how to keep changing motors and parts until all five come back good
KEY TERMS:
- Static Margin: The distance between the center of gravity and the center of pressure, divided by the body tube diameter. A margin of 1 or higher means a solidly stable rocket.
- Center of Pressure (CP): The point where all the aerodynamic forces on the rocket balance — where lift and drag act.
- Weathercocking: The rocket turning into the wind as it climbs. A little is normal; too much sends the rocket sideways instead of up.
- Velocity at Launch Guide Departure: The rocket's speed the moment it clears the launch rod — the speed the fins need in order to steer.
- Fin Flutter: The fin oscillating (flapping) itself apart at high speed. The fin safety margin is how much room you have below the critical flutter speed.
FAQ:
Q: What is the minimum static margin for a model rocket?
A: Anything above zero is technically stable, but Tim's rule of thumb is 1 caliber or higher. Short, stubby rockets tend to have a lower margin; long rockets naturally have more.
Q: How fast should my rocket be going when it leaves the launch rod?
A: 30 mph (44 ft/s) is the minimum Tim looks for. Below that the fins cannot correct the rocket, and it wobbles or weathercocks. Fix it with a longer launch rod or a higher-thrust motor.
Q: How do I lower my parachute deployment speed?
A: Choose a shorter motor delay. The last number in a motor name is the delay in seconds — a C6-5 waits 5 seconds after burnout, while a C6-3 opens the parachute 2 seconds earlier. The time you need depends on the rocket and the weather conditions. This is tricky, which is why you need a program like RockSim
Q: What is fin flutter, and how much margin do I need?
A: Flutter is the fin oscillating until it fails. RockSim calculates the critical flutter speed for your fins, and Tim keeps a 25% safety margin below that number.
PRODUCTS USED IN THIS VIDEO:
- RockSim Flight Simulation Software: apogeerockets.com/Rocket_Software/RockSim?utm_source=youtube&utm_medium=description
RELATED RESOURCES:
- How to Calculate and Optimize Your Rocket's Minimum Lift-Off Speed (Peak-of-Flight #683): apogeerockets.com/Peak-of-Flight/Newsletter683?utm_source=youtube&utm_medium=description
- Model Rocket Stability (Peak-of-Flight #462): apogeerockets.com/Peak-of-Flight/Newsletter462?utm_source=youtube&utm_medium=description
- How Windy is Too Windy for a Launch? (Peak-of-Flight #498): apogeerockets.com/Peak-of-Flight/Newsletter498?utm_source=youtube&utm_medium=description
- Venting Ejection Charges, Selecting Ejection Delays (Peak-of-Flight #520): apogeerockets.com/Peak-of-Flight/Newsletter520?utm_source=youtube&utm_medium=description
- Fin Flutter Analysis Revisited (Again) (Peak-of-Flight #615): apogeerockets.com/Peak-of-Flight/Newsletter615?utm_source=youtube&utm_medium=description
- Your First Rocket Club Launch: The No-Embarrassment Checklist (Video #468): apogeerockets.com/Advanced_Construction_Videos/Rocketry_Video_468?utm_source=youtube&utm_medium=description
Subscribe to the Apogee Components channel for weekly rocketry build videos, and visit apogeerockets.com to learn, shop, build, and fly!
#modelrockets #modelrocketry #howtomakeamodelrocket #RockSim
---
Free newsletter - new rockets, techniques and free plans: apogeerockets.com/Newsletter-Subscribe?utm_source=youtube&utm_medium=description










