E3Ds New Release...& What It Means for 3D Printing The Next Layer 2024-08-29 | In this video, I talk about the E3D Revo ecosystem and E3D's master plan. Brought to you by PCBWay. Go to pcbway.com/activity/anniversary10th.html and get EXCLUSIVE discounts as they celebrate their 10th anniversary 🎉(E3D did NOT sponsor this video, but if you would like to support the channel further, please consider using my link: jle.vi/e3D)Three years ago, when E3D came out with the first products in their REVO ecosystem, I'll admit that I was ...a little underwhelmed. At the time, they had just two "cold sides," their term for the heatsink, one low-powered "hot side" or ceramic heater, and 4 brass nozzle sizes. Not to mention, the flow was pretty limited, especially in this era of super high-speed printing. But right from the getgo, E3D was very clear: this is the direction their product line is going...Since that initial launch 3 years ago, E3D has been hard at work releasing not just more cold sides, but an entire lineup of accessories - and not just nozzles, either. Quietly, without most people taking notice, Revo has grown to become less of a hot-end standard and more of an entire 3D Printer toolhead ecosystem... with E3D High flow, E3D Obxidian, the E3D roto extruder, and much more... and I think it's worth taking a look at this line of 3D printer upgrades, both to try to understand the direction E3D seems to be taking as a 3D Printing company, and try to figure out what the future might hold. In fact, on that note, even if you know a bit about the REVO ecosystem already, stick around to the end, because I actually got my hands on one of their next generation products, the E3D PZ Probe, which is going to make one of the most popular upgrades out there 100% obsolete. 🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:54 Cold Sides (or Heatsinks)02:23 Extruders03:24 Heater Cores05:13 Nozzles, Nozzles, Nozzles07:07 Probes (Introducing E3D PZ Probe!)09:21 The Bigger Picture13:56 So Is It Time To Upgrade?🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 The RapidChange Revo hotend ecosystem by E3D: jle.vi/e3D (affiliate link)👉 My previous video about Bambu Lab's secret plan: youtu.be/_Ohg7l9bzMM👉 BigTreeTech Panda Revo for Bambu Lab: jle.vi/bigtreetech👉 The Prusa MK4S: jle.vi/prusa 🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
7 Functional 3D Prints That Solved REAL Problems The Next Layer 2024-10-11 | In this video, I share with you the 7 different solutions that I've designed to solve my own real-world problems. Brought to you by Thought3D, makers of Magigoo. Visit jle.vi/magigoo and apply coupon code "TNL" to get 15% off.Like many of you, I'm always working on improving my skills as a maker, and lately, one of my big goals has been to develop better CAD skills. After all, CAD skills are some of the highest impact, highest return-on-investment skills you can invest in as a maker. Unfortunately, I can't justify spending the time to model things I don't actually need just for practice. So for this reason, my learning method of choice is to actually design and build the things that I actually need for actual projects. (You know me, I LOVE functional 3d prints)So lately, I've been making an effort to solve more of my problems using CAD. Sometimes, this means designing things in CAD and then using other tools like lasers or power tools to build them, but more often than not, this means bringing 3D Printing into the mix, to design completely custom, one-off functional 3d prints to my particular problems.In this video, I'm going to take you through 7 different solutions that I've recently designed and 3d printed for some of my own real-world problems. I'll share with you how I - someone who is NOT trained as an engineer - approached the problems, and then turned them into awesome 3d prints. And while I'm not going to bore you with a CAD tutorial on Onshape tutorial for each thing I modeled, I will share some of the cool cad tricks and tips I learned and used along the way both to design and to print these solutions... in a way that is CAD software agnostic... so that you can try them on your own projects, too. (I personally like OnShape, but you can also use Fusion360, TinkerCAD, or FreeCAD to achieve the same results)My goal for this video is to inspire you to design some of your own functional 3d prints, even if you're not super proficient in computer aided design. 🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction02:37 Light Stand Leg Reinforcements06:29 HawkLock Quick Release Plates09:45 C-Stand and Varipole Cable Clips14:24 Plastic Shredder Funnel + Adapter17:00 Turbine Fan Mount + Grille21:45 Conclusion🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Onshape: https://onshape.pro/nextlayer👉 Polymaker: jle.vi/polymaker👉 Hex screws from AliExpress: https://a.aliexpress.com/_mqxwDfO👉 Turbine Fans: https://s.click.aliexpress.com/e/_msXNaXa👉 My previous video where I shared what I think is the best 3D design software for 3D printing: youtu.be/gEDRb67-HfQ👉 My videos where I attempt to build an affordable 3D Printer filament recycling setup: youtube.com/playlist?list=PLNAIMkOXd_V_o9dkTBbgP9_CMdNdmOdwv🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a "Super Thanks" (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Sovol SV08 Ultimate Toolchanger Build Series (Part 3: Electronics and Firmware Preparation) The Next Layer 2024-09-29 | Join us live as we begin building the Sovol SV08 into a 7-Toolhead Toolchanger 3D Printer. Brought to you by PCBWay: jle.vi/pcbwaySee Part 1 Here: youtube.com/live/2E8iKR_9BXM?feature=shareIn this livestream, we'll be taking the Sovol SV08, Based on the Voron 2.4 3D Printer, and converting it into a 7 toolhead toolchanger. In the first livestream, we built the BondTech BMG version. This time, we will try to figure out the wiring, electronics, and firmware part of things. Tune in Live! See you there!🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discordMainline Klipper SV08 GUIDE! github.com/Rappetor/Sovol-SV08-Mainline🔗 THANKS TO THE PRODUCT SPONSORS OF THIS PROJECT: 🔗👉 Sovol: jle.vi/sovol👉 LDO Motors: ldomotion.com | ldomotors.com👉 Polymaker: jle.vi/polymaker👉 BondTech: https://bondtech.se👉 Phaetus: phaetus.com👉 E3D: jle.vi/e3d👉 Slice Engineering: jle.vi/slice🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Spartacus Toolhead: printables.com/model/745412-spartacus-the-toolhead🗿 🗿 🗿 🗿 🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Converting the Sovol SV08 Into a 7 Tool Head MONSTER! The Next Layer 2024-09-27 | In this video, we begin turning the Sovol SV08 3D Printer into a 7 toolhead tool changer using the stealthchanger design. Brought to you by Sovol, makers of my favorite budget 3D printers. Check them out at jle.vi/sovol So, I've finally begun converting my Sovol SV08 into a 7 tool changer 3d printer, based on the stealthchanger! And in this video, I'll be outlining the different choices I made for each of the sv08 mods, hot ends, extruders, etc - as well as WHY I chose each of those. While this video was written before I started actually building this DIY 3D printer, I think it's important to document the project and the approach, for anyone who wants to recreate it later on.(By the way, I've already done two livestreams and built the two tool heads, so if you want to watch those live streams, you can check them out here: youtube.com/watch?v=8lBd1R-EEQg&list=PLNAIMkOXd_V9jdPlKDvLn1b1i14LN-vcy)🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction00:32 Project Objectives03:05 The Toolchanger Design04:14 The Toolhead Design06:55 The Hot Ends12:07 The Extruders14:21 Electronics15:44 Enclosure & Screen16:43 Next Steps🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Teaching Tech: youtube.com/teachingtech👉 The StealthChanger Project by DraftShift: github.com/DraftShift/StealthChanger👉 My livestreams where I'm building the Sovol SV08 Tool changer: youtube.com/watch?v=8lBd1R-EEQg&list=PLNAIMkOXd_V9jdPlKDvLn1b1i14LN-vcy👉 My livestreams where I build an Enraged Rabbit Carrot Feeder (ERCF) V2: youtube.com/playlist?list=PLNAIMkOXd_V8UITY13F497-lr_v0yXx3x👉 My open letter to the 3D printing community: youtu.be/YRayFmMYFxM👉 My recent video about the REVO ecosystem: youtu.be/3aYt4Qy-JoA👉 My previous video about my 3D printed shoes: youtu.be/PKk7EDsryqE👉 My Voron Builds: youtube.com/playlist?list=PLNAIMkOXd_V-w8ZswanKWks2KKJz9DipJTHANK YOU TO THIS PROJECT's SPONSORS 🙏🙏 Sovol: jle.vi/sovol🙏 Nadir at CN3D on YouTube: studio.youtube.com/channel/UC5lzueDDE7wtiaKgIaUr_Iw🙏 Nadir at CN3D on Printables: printables.com/@Nadir🙏 E3D: jle.vi/e3d🙏 PolyMaker: jle.vi/polymaker🙏 Slice Engineering: jle.vi/slice🙏 Phaetus: phaetus3d.com🙏 DropEffect: dropeffect.com🙏 BondTech: https://bondtech.se🙏 LDO Motors: ldomotion.com | ldomotors.com🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Sovol SV08 Tool Changer Extrusion Adapters by Richard Ferrington: printables.com/model/902562-sovol-sv08-tool-changer-extrusion-adapters🗿 Spartacus Toolhead by Nadir (BMG): printables.com/model/745412-spartacus-the-toolhead🗿 Spartacus Toolhead by Nadir (LGX): printables.com/model/900809-spartacus-lgx🗿 Sovol SV08 Top Hat by Nadir: printables.com/model/865851-sovol-sv08-top-hat🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #sv08
Ep. 46: Martin Owens, Inkscape developer: What Open Source Hardware Can Learn From Software The Next Layer 2024-09-27 | In this episode, we’re joined by Martin Owens, Inkscape developer. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!Meet Martin Owens, a dedicated Free and Open Source developer with a passion for Inkscape, a leading graphics program used by designers and creators worldwide. As an independent contractor, Martin collaborates closely with his financial supporters to shape the future of Inkscape, focusing on features that empower users. Through engaging videos and social media updates, he shares progress and insights into his work, making Inkscape an invaluable tool for graphic designers and 3D printing enthusiasts alike. Join us as we dive into the world of open-source development and creativity!🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS 🔗👉 Subscribe to Martin's channel: youtube.com/@doctormo👉 Support Martin: patreon.com/doctormo🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links ❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Sovol SV08 Ultimate Toolchanger Build Series (Part 2: Spartacus LGX Toolhead #2 Assembly) The Next Layer 2024-09-25 | Join us live as we begin building the Sovol SV08 into a 7-Toolhead Toolchanger 3D Printer. Brought to you by PCBWay: jle.vi/pcbwaySee Part 1 Here: youtube.com/live/2E8iKR_9BXM?feature=shareIn this livestream, we'll be taking the Sovol SV08, Based on the Voron 2.4 3D Printer, and converting it into a 7 toolhead toolchanger. In the first livestream, we built the BondTech BMG version. This time, we will build the BondTech LGX Version. We'll be joined by @nadir3D of the CN3D team, creators of the Spartacus toolhead design, and adapting it to the @DraftShiftDesign "Stealthchanger" toolchanger for Voron 3D Printers. Tune in Live! See you there!🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 THANKS TO THE PRODUCT SPONSORS OF THIS PROJECT: 🔗👉 Sovol: jle.vi/sovol👉 LDO Motors: ldomotion.com | ldomotors.com👉 Polymaker: jle.vi/polymaker👉 BondTech: https://bondtech.se👉 Phaetus: phaetus.com👉 E3D: jle.vi/e3d👉 Slice Engineering: jle.vi/slice🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Spartacus Toolhead: printables.com/model/745412-spartacus-the-toolhead🗿 🗿 🗿 🗿 🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Sovol SV08 Ultimate Toolchanger Build Series (Part 1: Spartacus BMG Toolhead #1 Assembly) The Next Layer 2024-09-22 | Join us live as we begin building the Sovol SV08 into a 7-Toolhead Toolchanger 3D Printer. Brought to you by PCBWay: jle.vi/pcbwayIn this livestream, we'll be taking the Sovol SV08, Based on the Voron 2.4 3D Printer, and converting it into a 7 toolhead toolchanger. We'll be joined by @nadir3D of the CN3D team, creators of the Spartacus toolhead design, and adapting it to the @DraftShiftDesign "Stealthchanger" toolchanger for Voron 3D Printers. Tune in Live! See you there!🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 THANKS TO THE PRODUCT SPONSORS OF THIS PROJECT: 🔗👉 Sovol: jle.vi/sovol👉 LDO Motors: ldomotion.com | ldomotors.com👉 Polymaker: jle.vi/polymaker👉 BondTech: https://bondtech.se👉 Phaetus: phaetus.com👉 E3D: jle.vi/e3d👉 Slice Engineering: jle.vi/slice🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Spartacus Toolhead: printables.com/model/745412-spartacus-the-toolhead🛒 RECOMMENDED GEAR: 🛒📍 Nadir's Recommended Crimping Tool: https://s.click.aliexpress.com/e/_DETdK1x📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
These Are Some AWESOME 3D Prints! The Next Layer 2024-09-19 | In this video, I share one of my FAVORITE 3D printed gifts / toys - marble runs. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!Like most of you, I typically don't 3D print a lot of toys or chotchkes... much less make an entire video about them... but these... honestly, are just too much fun for the entire family to NOT share with all of you. Honestly, I think they're one of my top "cool things to 3d print" of all time. So in this video I'm going to share why these are so cool, where to download them, recommended print settings, and tips to get the best results. Also, let me know in the comments if you like this shorter format of "best things to 3d print" and maybe I'll do more videos like this!🤫 Get my custom filament and 3d printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction00:50 What Are They?01:36 Why Are They Such Cool Things to 3D Print?03:28 How To 3D Print Them?07:26 Assembly08:39 Necessary Hardware09:36 Where to Download & Which To 3D Print First12:40 Next Steps🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Ball Bearings (AliExpress - Recommended): https://s.click.aliexpress.com/e/_mPQNP3m👉 6mm Ball Bearings (Amazon - $$$): amzn.to/3MOOJ3u👉 9mm Ball Bearings (Amazon - $$$): amzn.to/3TAzjDF👉 Polymaker filament: jle.vi/polymaker👉 SliceWorx filament: sliceworx.com/?ref=JONATHANLEVI👉 CookieCAD 3D Printer filament: amzn.to/4gsGYhh👉 ZIRO3D 3D Printing filament: amzn.to/3MQNyRa👉 eSun filament: amzn.to/47tuWjH👉 Magigoo: jle.vi/magigoo👉 3D Gloop: jle.vi/gloop👉 My previous video where I talked about the 20 most beautiful filaments on the market right now: youtu.be/P-cRMhESGks👉 My previous video about 3D printed gifts: youtu.be/FpWp0gCCnxg👉 My previous video where I shared a bunch of underrated 3D printing products you need: youtu.be/h2Qluh8XBPs🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 My Printables Collection of My Recommended Marble Runs: printables.com/@JonathanLevi/collections/1698226🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
13+ New 3D Printing Products Coming Out Soon The Next Layer 2024-09-12 | In this video, we're going to check out the most highly-anticipated new products coming to market in the 3D Printing Industry over the next few months. Brought to you by Sovol. Check out their affordable and high-quality 3D Printers at jle.vi/sovolHoliday season is just around the corner, and that means tons of exciting new products from all of your favorite 3D printing manufacturers... In this video, we're going to look at over a dozen new products coming out soon, including features, anticipated price, and release date. Oh, and are you a Bambu user? Get excited, because there are a TON of new Bambu Lab Upgrades coming up for your printers. 🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction00:37 Prusa01:56 E3D02:50 Slice Engineering Bambu Lab Upgrades04:01 Creality06:41 AnyCubic 07:13 BigTreeTech & BIQU Bambu Lab Upgrades09:19 Sunlu09:47 WhamBam10:33 EIBOS11:16 FYSETC🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Prusa Hackerboard: jle.vi/prusa👉 E3D PZ Probe: jle.vi/e3D👉 The Mako™ hot-end for Bambu Lab by Slice Engineering: jle.vi/slice👉 Creality K1 SE: jle.vi/creality👉 AnyCubic Photon Mono M7: jle.vi/anycubic👉 BigTreeTech & BIQU: jle.vi/bigtreetech👉 Sunlu PLA+ 2.0 filament: jle.vi/sunlu👉 Carbon Fiber flex plates by WhamBam: jle.vi/whambam👉 AMS add-on filament dryer by EIBOS: jle.vi/eibos👉 FYSETC Nevermore StealthMax Kit: aliexpress.us/item/3256807470215564.html?pdp_npi=👉 My live unboxing of the Prusa MK4S: youtube.com/live/BV847s22LTo?si=m7rxh5rujumIrjkj👉 Prusa's video about the MK4S: youtu.be/VO2MaQrUcqE?si=zmQ0YDwYZfuOkq2C👉 My video where I talked about the E3D Revo ecosystem and covered the E3D PZ Probe: youtu.be/3aYt4Qy-JoA👉 Slice Engineering's important update on the delay in the shipment of the Mako™ hot-ends: youtu.be/epky297tEKo?si=P3DNMV9x0MvUqN4H👉 Thomas Sanladerer's video about the airborne particles that 3D printers produces: youtu.be/nofn_MHrxrs?si=hGVGZknO2IptkJJq🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
These Underrated Products Make 3D Printing Fun Again The Next Layer 2024-09-05 | In this video, I share a bunch of underrated 3D printing products you should check out. Brought to you by Sovol. Check out their wide range of highly affordable 3D printers at jle.vi/sovolYou guys know me... I love a good listicle. I've done listicle videos on things to 3D print, hardware to keep around, tools you need... But in this video, I want to share with you guys a handful of products that I literally can't believe more people don't talk about. Products that have completely transformed 3D Printing for me, giving me fewer failures, fewer headaches, and less wasted filament. Let's get after it!🤫 Get my custom filament and printer profiles, buyers guides, discounts on many of the products in this video, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction00:57 Specialized Bed Adhesives05:40 Plastic Repellent Paint08:59 Specialized 3D Print Glues11:26 Specialized Metal Bed Scraper13:05 Nozzle Maintenance Kit🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Specialized Bed Adhesives from Magigoo: jle.vi/magigoo 👉 Plastic Repellent Paint from Slice Engineering: jle.vi/slice👉 Specialized 3D Print Glues from 3D Gloop: jle.vi/gloop👉 Specialized Metal Bed Scrape on AliExpress: https://s.click.aliexpress.com/e/_DBI6YoR👉 Nozzle Maintenance Kit from Wham Bam: jle.vi/whambam👉 My previous video where I talked about the Revo ecosystem: youtu.be/3aYt4Qy-JoA👉 My previous video where I shared the 3D printing tools you need part 1: youtu.be/rGnbgI8WRxo and part 2: youtu.be/ZzZ_zZFcr80🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Ep. 45: Sjon Huisman of Blobifier on 3D Printer Customizations The Next Layer 2024-08-30 | In this episode, we’re joined by Sjon Huisman. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!Sjon (or John) Huisman is a lecturer in IT and software engineering, who also happens to be a passionate maker and 3D printing enthusiast. With a background in teaching and a love for tinkering, John shares how he merges his expertise in software engineering with his hobby of automating his home and enhancing his 3D printers. Tune in as John dives into his journey of balancing family life, teaching, and pushing the boundaries of 3D printing innovation.🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer💬 JOIN MY DISCORD: jle.vi/tnl-discord🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links ❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
I Got The ERCF V2 Working. Heres What I Learned. The Next Layer 2024-08-24 | In this video, I share an update on my ERCF V2 or Enraged Rabbit Carrot Feeder. Brought to you by Sovol. Check out their wide range of highly affordable, Klipper-based 3D printers at jle.vi/sovolSooo... I did it. After weeks, months... I honestly don't know how long... I finally got the ERCF V2 build done and working - mostly. It wasn't easy. But between dogged perserverence, moral support on livestreams, and the tremendous help of the Enraged Rabbit Carrot Feeder Discord... we got there. In this video, I document everything I learned along the way, what it took to actually get the ERCF V2 working, and the answers to some of your most pressing questions, including how it compares to the bambu lab AMS, Prusa MMU3, Prusa XL, and Tap changer... all so that you can decide if you really want to take on this challenge on your own, and if you do, you will know how to overcome the hurdles that I did. Because, apparently, according to people in the know, I unsurprisingly hit just about every roadblock you can!🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:24 Upgrading The Toolhead03:36 Upgrading KlipperScreen05:20 Installing & Configuring Happy Hare06:20 Updating Your Slicer07:03 Upgrading the Servo08:18 Re-printing for Better Clearances11:08 Installing & Configuring The Filament Cutter12:46 Removing ERCT Spacers13:21 Shaving Down Disruptive parts14:25 Calibrating, Calibrating, Calibrating16:37 Test Prints16:37 Your Questions, Answered 17:39 How Long Did This Take? 18:13 Will this work on my printer? 18:53 How much does it waste? 20:36 How fast is it? 22:10 How well does it work? 23:21 How does it stack up against other systems on the market? 25:37 ERCF? Toolchanger? Which one is better? 27:16 Who is this for? Should I build one?🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 FYSETC ERCF V2 Kit: jle.vi/fysetc👉 BigTreeTech EBB36: jle.vi/bigtreetech👉 LDO Motors NiteHawk SB: jle.vi/matterhackers👉 Savox servo: amzn.to/4dAuHp1 [Amazon]👉 Makerbase MKS THR36 Toolhead Board: https://s.click.aliexpress.com/e/_DBHt6cP👉 E3D High-Flow Hot End: jle.vi/e3d👉 Happy Hare Wiki: github.com/moggieuk/Happy-Hare👉 My previous ERCF V2 video: youtu.be/Vx9B111Fu38👉 My ERCF Livestreams: youtube.com/playlist?list=PLNAIMkOXd_V8UITY13F497-lr_v0yXx3x👉 My podcast interview with ERCF team member Ivan Trail: youtube.com/live/T5J_Z-3uEpo🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Upgraded Filametrix Cutting Arm: printables.com/model/922090-filametrix-cutting-arm-with-magnet🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #ercf
LIVE UNBOXING: PRUSA MK4S 🚀 The Next Layer 2024-08-19 | In this video, we’ll be doing a live unboxing + first prints with the Prusa MK4S. Brought to you by PCBWay. Check them out at jle.vi/pcbway today!Exciting news! Prusa Research actually reached out and said that they’d appreciated a recent video advocating for supporting Open Source 3D printing, and they wanted to send over a new MK4S for me to play around with!I’ve long been a fan of Prusa, though I have at times been critical of them, and I was really excited to accept, and to start a working relationship with a company I admire so much. As far as I understand, I am under no obligation to create any content or do anything, and all opinions are my own. Should you decide you want to pick one up, you can use my link, which will support the channel and future content creation. Tune in live with your questions, and let’s do some 3D Printing! 🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 jle.vi/prusa🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 🗿 🗿 🗿 🗿 🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Enraged Rabbit Carrot Feeder v2 in action The Next Layer 2024-08-13 | Watch the Enraged Rabbit Carrot Feeder v2 in action! See the latest version of the ERCF, also known as the Enraged Rabbit Carrot Feeder, in this video... it's working on my Voron 2.4!
Now You Can Recycle Your 3D Prints Affordably* The Next Layer 2024-08-10 | This video is part 4 of my attempt to build an affordable 3D Printer filament recycling setup - the last of the series. Brought to you by PCBWay. Go to pcbway.com/activity/anniversary10th.html and get EXCLUSIVE discounts as they celebrate their 10th anniversary 🎉What feels like a lifetime - and a lot of wasted money - ago, I set out on a pretty ambitious project: To create a DIY, at-home rig that could recycle 3d printer waste into brand new filament... and which was reproducible by all of you at home. My project's progress parts 1 to 3 ➡️ youtube.com/playlist?list=PLNAIMkOXd_V_o9dkTBbgP9_CMdNdmOdwvIt's been a heck of a journey, with a lot of learning, expensive mistakes, and frustration along the way... but I finally have something to show for it...These 3D prints that I'm going to show in this video are made entirely from recycled 3D prints, supports, and purge lines, which I ground up myself, with 0 additives or new material... and they're not half bad!So in this video, we're going to talk about what it took to get here, what I learned along the way, and whether or not it makes sense for YOU to replicate my setup at home. Ultimately, we're going to answer the following questions: Can you recycle failed 3D prints, at home, for less than $2,000? Is a filament recycler economically viably for the average user? Is the artme 3d filament maker the solution to this problem? Or is it just another filament extrusion machine that is out of reach for the average user? And ultimately, should you make your own filament at home? Or should the "average" user not really bother to recycle 3d printer waste at all? 🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:24 Where We Left Off02:34 Finishing The Build04:54 Wiring & Firing It Up06:26 Working Through Bugs & Issues11:01 The Filament Recycling Process From Start To Finish17:26 How Does It Print?19:27 What It All Cost23:16 Should You Build One?🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 PolyMaker 3d printer filament: jle.vi/polymaker👉 SliceWorx: sliceworx.com👉 Recycling Fabrik: recyclingfabrik.com👉 ARTME 3D filament extrusion machine: https://artme-3d.shop/👉 Precious Plastics filament recycler shredder kit: community.preciousplastic.com/how-to/shredder-21👉 PPCapi Spain (Where I bought my recycling kit. Mention me at checkout to get a free upgrade to conical drilled holes - which you need): ppcapispain.com/en-gb/shredder-v2-1-regular-steel-kit🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Man vs. MMU: Will I EVER Get the ERCF V2 Working? The Next Layer 2024-08-02 | In this livestream, I’m going to sink more hours into trying to get the ERCF V2 working (and probably fail, let’s be real here). Brought to you by PCBWay: jle.vi//pcbway Tune in live and help me before I give up. Here’s the kit I’m building: jle.vi/ercf⏯️ Part 1: youtube.com/live/zoLUqNdSQYg⏯️ Part 2: youtube.com/live/Co3W5VFxB9c⏯️ Part 3: youtube.com/live/_jWXuMd0j_I⏯️ Part 4: youtube.com/live/nvVnp0WHYgI🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 👉 👉 👉 👉 👉 🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
I 3D Printed My Own Shoes The Next Layer 2024-07-31 | Can 3D Printing create the perfect, ergonomic, barefoot shoe? Let's find out! Brought to you by Sovol. Check them out at jle.vi/sovol (and their new filament dryer: jle.vi/sh02). 3D Printed shoes are already a thing—from Zellerfeld shoes seen on Stefan from CNC Kitchen and Eric from BigTreeTech, to the mass-produced Adidas 4DFWD.But there are reasons you haven't seen me in 3D Printed shoes. My unofficial slogan is "We don't buy sh*t... We build sh*t... and occasionally fish it out of the trash." Half the fun in 3D printed products is making them yourself, to your own spec, size, and colors, at home. If I'm spending $200 on shoes, I prefer ones with technologies I can't 3D Print, like soft fabrics and rubber. Also, most 3D Printed shoe models are chonky, which doesn't fit my preference for barefoot shoes that improve balance, dexterity, and reduce joint pain. I can't go back to "normie" shoes.So, imagine my excitement when I saw a Reddit user, Alessio, designing custom 3D Printed shoes that are actually printable at home with no supports or fancy printers. I pitched him on making a BAREFOOT shoe with all the benefits of 3D Printing, without looking like a space alien clown shoe from the future.Most of you probably aren't into barefoot shoes, and there are plenty of videos on 3D Printing shoes, so to make this interesting for everyone, I'll be testing a wide range of materials—from common TPUs to exotic filaments—to find the best material for YOU to print a shoe in. I'll share lessons learned, how to get the best results, and how well these shoes hold up over time. For now, let's go make some shoes.🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction03:01 Finding The Right Equipment06:39 Filamentum TPU (92A)10:24 PolyMaker TPU (90A)13:46 NinjaTek Chinchilla TPE (75A)17:12 Plastics App FLEX (70A)23:12 Balena BioCir®flex3D (80A)26:49 Conclusion🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Sovol SH02 Filament Dryer: jle.vi/sh02👉 Sovol SV07 Plus: jle.vi/sovol ($10-20 OFF on 3D printer orders of $259 or more)👉 Comgrow T300: jle.vi/comgrow👉 Alessio’s models on Cults (barefoot ones coming soon): cults3d.com/en/users/Alessio_RiverFamily/3d-models👉 Filamentum 92A TPU: jle.vi/fillamentum👉 PolyMaker 90A TPU: jle.vi/polymaker 👉 NinjaTek Chinchilla TPE: jle.vi/chinchilla 👉 Plastics App Perform U70 TPU: plastics-app.com/product/perform-%E2%9C%94-u70-ultra-soft-tpu-70a-3d-filament👉 Balena BioCir®Flex 3D: https://balena.science/pages/biocirflex3d👉 My video where I talk about the ERCF v2 or Enraged Rabbit Carrot Feeder: youtu.be/Vx9B111Fu38👉 My playlist of videos where I build an Enraged Rabbit Carrot Feeder (ERCF) V2 from FYSETC and share my progress: youtube.com/playlist?list=PLNAIMkOXd_V8UITY13F497-lr_v0yXx3x👉 My "exotic filaments" video: youtu.be/iiwByWHs6UU👉 My playlist of videos all about filaments: youtube.com/playlist?list=PLNAIMkOXd_V8udHlknRPDOjN5V1kAd0lZ👉 My "3D printing with literal trash" video: youtu.be/w3lIKdqGvI4🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
I RECYCLED FILAMENT TODAY! Video coming soon(ish) The Next Layer 2024-07-22 | I finally did it. I finally was able to recycle 3D printer filament. I’m doing a video about what it took to get here and a cost breakdown, so make sure you’re subscribed!
An Open Letter to the 3D Printing Community The Next Layer 2024-07-18 | I'm pretty sure this video is going to bomb, but I just can't keep silent anymore. I've been stewing on this for a couple weeks at this point, and I honestly just need to get it off of my chest. (There is no sponsor for this video... go support your favorite open source project!)One of the most incredible things about the 3D printing community, without a doubt, is the collaborative, open source nature. It's mind-blowing, actually, that in our little corner of the internet, people contribute so much of their hard work and talent towards creating things that all of us can use and enjoy. I absolutely love it. But with that said, as I've gone deeper into this community, I've come to notice what I believe to be a major issue that is holding back our beloved little community. The people at the forefront - the ones moving us forward with true innovations that the rest of the industry later adopts (i.e. klipper, mainsail, fluidd, orcaslicer, the ercf / enraged rabbit carrot feeder v2, freecad, stealthchanger, the voron tool changer, tradrack, type things) - are not being compensated for their work. I wrote this from the heart, and know that I was just as guilty as any of us. But, the more I thought about it, the more I realized we need to change it. So, to be the change I wish to see, I made donations to Voron Design, Nadir, OrcaSlicer, Klipper, and Mainsail before requesting that you guys do the same. I hope you'll take the time to listen to the argument I have to make, and whether or not you agree, I'd love to hear your thoughts in the comments below. I read them all, and try to respond to as many as I can.🤫 Get my custom filament and printer profiles, buyers guides, and much, much more on Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord💰 SUPPORT THESE PROJECTS: 💰👉 OrcaSlicer: ko-fi.com/SoftFever or paypal.me/softfever3d👉 Klipper: ko-fi.com/koconnor or patreon.com/koconnor👉 Mainsail: https://docs.mainsail.xyz/#support-mainsail 👉 Fluidd: github.com/fluidd-core/fluidd👉 Octoprint: octoprint.org/support-octoprint👉 Voron Design: vorondesign.com👉 FreeCAD: freecad.org/sponsor.php👉 @nadir3D (Xenomorph, Spartacus): paypal.me/NDRNADIR @UC5lzueDDE7wtiaKgIaUr_Iw👉 Stealthchanger: github.com/DraftShift/StealthChanger👉 Tapchanger: No donation link found! github.com/viesturz/tapchanger👉 Enraged Rabbit Carrot Feeder (ERCF v2): No donation link found! github.com/Enraged-Rabbit-Community/ERCF_v2👉 Happy Hare: github.com/moggieuk/Happy-Hare👉 Tradrack: No donation link found! github.com/Annex-Engineering/TradRack👉 8-Track MMU: No donation link found! github.com/ArmoredTurtle/8-Track-Raven-Alpha 👉 DAKSH Voron toolchanger: No donation link found! github.com/ankurv2k6/daksh-toolchanger-v2👉 YMIR/FENRIR 3D Printers by @MakerViking : patreon.com/makerviking 👉 VzBot by @Vez3D: github.com/VzBoT3D/VzBoT-Vz330👉 Positron 3D Printer: paypal.com/donate/?hosted_button_id=YGPRVTSHN4FQG👉 Hedgehog Makes 3D Printing Support: patreon.com/hedgehogmakes👉 Am I missing your project? Message me on Discord: @jonathanalevi 🔗 OTHER LINKS MENTIONED IN THE VIDEO: 🔗👉 Get the Sovol SV08 (and help support the Voron project!): jle.vi/sovol👉 Get Voron from LDO (and help contribute to the Voron project!): jle.vi/voron👉 Buy from BigTreeTech (who supports Klipper!): jle.vi/bigtreetech👉 Buy from Obico (who supports Klipper!): jle.vi/obico👉 My Voron build livestreams: youtube.com/playlist?list=PLNAIMkOXd_V-w8ZswanKWks2KKJz9DipJ👉 My Enraged Rabbit Carrot Feeder (ERCF V2) build livestreams: youtube.com/playlist?list=PLNAIMkOXd_V8UITY13F497-lr_v0yXx3x🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this videoBusiness inquiries: thenextlayer@influint.co #3dprinting #3dprinted #3dprinter
My kid invented an awesome #3dprinted bottle protector The Next Layer 2024-07-18 | If you want to download and 3D Print this awesome bottle protector yourself, check it out here:printables.com/model/945744-bottle-rocket-protective-koozie-sleeve-for-kids-wa
#3dprinter filament recycling project update!!! The Next Layer 2024-07-17 | A lot of you have been asking for updates about my 3-D printer filament recycling project. Thanks to PCBWay for sponsoring many parts of this build. I wish I’d just used them for everything I needed, instead of trying to chase down awful industrial suppliers and begging them to sell me one part for 5X markup. Check out PCBways awesome 10th anniversary sale if you don’t want to make the same mistake I did 😂 pcbway.com/activity/anniversary10th.html
ERCF V2: Configuration, Tuning... First Prints??? The Next Layer 2024-07-09 | Join us live where we’re going to (try to) get the ERCF V2 printing. Brought to you by PCBWay: jle.vi/pcbwayIn the previous 3 livestreams, we’ve built the ERCF V2, flashed the software, and all that. Now let’s get it printing… or at least try to. (We’ll be working directly with the ERCF Discord, where I’ll post questions, specifically so that others can see the answers there, too). The kit I’m using is from jle.vi/ercf ⏯️ Part 1: youtube.com/live/zoLUqNdSQYg⏯️ Part 2: youtube.com/live/Co3W5VFxB9c⏯️ Part 3: youtube.com/live/_jWXuMd0j_I⏯️ Part 5: youtube.com/live/Zr068i7PzFw🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 PolyMaker: jle.vi/polymaker👉 FYSETC: jle.vi/fysetc👉 Previous 3 Livestreams: youtube.com/watch?v=WGqJnGF38_0&list=PLNAIMkOXd_V8UITY13F497-lr_v0yXx3x 👉 Summary Video: youtu.be/Vx9B111Fu38?si=dLUJujBkXQt_cHFC 🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #ercfv2
Why Dont More People Build This Open Source AMS/MMU? The Next Layer 2024-07-08 | In this video, I talk about the ERCF v2 or Enraged Rabbit Carrot Feeder. Brought to you by PCBWay. Go to pcbway.com/activity/anniversary10th.html and get EXCLUSIVE discounts as they celebrate their 10th anniversary 🎉For the last few weeks, I've been working on printing and assembling the latest edition of the ERCF, or Enraged Rabbit Carrot Feeder. It's basically an open-source multimaterial switcher, akin to a Bambu Lab AMS or a Prusa MMU, but it prints 8 to 12 colors or materials... and it's printer-agnostic... meaning that you can install it on any printer running Klipper, and turn it into a magnificient, multi-color machine.In this video, I'm going to explain a bit about this system, how it works, what's involved, and so on. You'll learn what the ERCF v2 actually IS, what's involved in building it, and whether or not I recommend that YOU build your own Enraged Rabbit Carrot Feeder. I really hope you enjoy it. 🤫 Get behind the scenes and exclusive content such as my custom printer and filament profiles on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:35 About the ERCF v203:15 How It Works05:48 ERCF 1.1 vs. ERCF 212:48 The Build Experience16:13 Electronics, Firmware, and Software17:39 Where Things Stand🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 ERCF v2 kit from FYSETC: jle.vi/ercf👉 Voron Stealthburner Kit from FYSETC: jle.vi/fysetc 👉 My livestreams where I build an Enraged Rabbit Carrot Feeder (ERCF) V2 from FYSETC and share my progress: youtube.com/playlist?list=PLNAIMkOXd_V8UITY13F497-lr_v0yXx3x👉 My interview with Ivan Trail, ERCF v2 Team Member, on Open Source Multicolor Printing: youtube.com/live/T5J_Z-3uEpo👉 My Voron build livestreams:youtube.com/playlist?list=PLNAIMkOXd_V-w8ZswanKWks2KKJz9DipJ🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
I got the ERCF v2 working… then decided to redo the tool head to CANBUS 😢 The Next Layer 2024-06-30 | In this video, I finally got the ERCF working, but then decided to redo the tool head to CANBUS. Check out the latest updates on the enraged rabbit carrot feeder V2 for Voron 2.4!
My Long-Term Review of Each 3D Printer I Own The Next Layer 2024-06-27 | In this video, I talk about which of my many 3D Printers do I ACTUALLY USE. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!So without a doubt, the biggest perk of having a 3D printing YouTube channel is getting access to the latest, greatest 3D printers and getting to try them out and review all of them. But unfortunately, sometimes by the time I've published a video, I may not have had as much time on the machine as I want to...So I thought it might be really, really fun to give you guys a tour around the studio to show you which printers I've actually held onto over the years and which ones I haven't. As well as how many hours I've put on the ones that I've actually kept, or maybe why I haven't.🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:38 LDO Voron 2.4 350mm (Python)04:09 Prusa MK3S+ (Tortoise)05:40 Bambu Lab X1 Carbon (Cheetah)07:56 Bambu Lab P1S (Panther)09:23 LDO Voron 0.2 (Viper)11:39 Bambu Lab X1 Carbon (Tiger)13:11 Bambu Lab A1 Minis (Lynx & Bobcat)15:11 Siboor Voron 0.2 (Rattlesnake)17:19 Sovol SV07 Plus (Orca)19:04 Creality K1C (Greyhound)20:33 Sovol SV08 (Shark)22:18 Resin Printers22:41 LDO Positron 3.2 (Bat)24:37 Comgrow T300 (Narwal)27:15 AnyCubic Kobra 3🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 LDO Voron Kits: jle.vi/voronkits 👉 Prusa MK3S+: jle.vi/prusa👉 Bambu Lab Printers: jle.vi/bambu (supports 3D Print General, who’s channel was deleted)👉 Sovol Printers: jle.vi/sovol 👉 Creality K1C: jle.vi/creality👉 Comgrow T300: jle.vi/comgrow👉 AnyCubic Printers: jle.vi/anycubic👉 E3D Revo Hotend: jle.vi/matterhackers👉 Mintion Beagle Smart Camera: jle.vi/mintion👉 Panda Revo Hotend: jle.vi/bigtreetech👉 PolyMaker Filament: jle.vi/polymaker👉 My Voron 2.4 Build Video: youtu.be/UQl1zfmUYRY👉 My Voron 0.2 Build Livestream: youtube.com/live/0CqAJet3SdA👉 My Sovol SV07 Review: youtu.be/ph5P-jcFzzA👉 My Creality K1C Review: youtu.be/2USBq4zGHbI👉 My LDO Positron V3 Review: youtu.be/6qdbGFrwt8U👉 My Comgrow T300 Build Livestream: youtube.com/live/Qgs_AsOxeAo👉 My AnyCubic Kobra 3 Combo Review: youtu.be/2CurchA4HT8👉 All of My 3D Printer Reviews: youtube.com/playlist?list=PLNAIMkOXd_V9rS0RXQfGyNZL0Wmr0GDS4👉 My interview with Dr. Ye Tao, CEO of Bambu Lab: youtube.com/live/FaOrQD9PqNc🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 SOVOL SV08 CN3D Shroud by Nadir on Printables: printables.com/model/916158-sovol-sv08-cn3d-shroud🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Lets Finish (Maybe) an ERCF V2 Open Source MMU (Part 3) The Next Layer 2024-06-26 | In this livestream, we’re going to try to finish building an Enraged Rabbit Carrot Feeder (ERCF) V2 from FYSETC. This stream is brought to you by PCBWay. Get $5 off your first order at jle.vi/pcbwayIn the first two livestream, we went for 10 hours (!) and got a lot done. Then, redone, because we did it wrong! ⏯️ Part 1: youtube.com/live/zoLUqNdSQYg⏯️ Part 2: youtube.com/live/Co3W5VFxB9c⏯️ Part 4: youtube.com/live/nvVnp0WHYgI⏯️ Part 5: youtube.com/live/Zr068i7PzFwIf you enjoy the stream, please consider supporting the channel using the following links:🎁 Tip (Appears on Leaderboard) streamlabs.com/thenextlayer/tip🎁 SuperChat (appears on Leaderboard)🎁 Join our Patreon for exclusive content: patreon.com/thenextlayer🎁 Become a YouTube Member by clicking “Join”💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 PolyMaker: jle.vi/polymaker👉 FYSETC: jle.vi/fysetc👉 ERCF v2 Kit: jle.vi/ercf👉 Voron Kits: jle.vi/voronkits🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #voron
Lets Build a FYSETC ERCF V2 (Multicolor System) (Part 2) The Next Layer 2024-06-26 | In this livestream, we’re going to continue building an Enraged Rabbit Carrot Feeder (ERCF) V2 from FYSETC. You can pick one up here: jle.vi/ercfIn the first livestream, we went for 7 hours (!) and got a lot done. Then, redone, because we did it wrong! Check it out here: youtube.com/live/zoLUqNdSQYg⏯️ Part 1: youtube.com/live/zoLUqNdSQYg⏯️ Part 3: youtube.com/live/_jWXuMd0j_I⏯️ Part 4: youtube.com/live/nvVnp0WHYgI⏯️ Part 5: youtube.com/live/Zr068i7PzFwIf you enjoy the stream, feel free to send a “Super Thanks” or become a YouTube member / Patreon supporter: patreon.com/thenextlayer All proceeds go towards upgrading our equipment to make future videos better for you!💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 PolyMaker: jle.vi/polymaker👉 FYSETC: jle.vi/fysetc👉 Voron Kits: jle.vi/voronkits🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #voron
Lets Build a FYSETC ERCF V2 (Multicolor System) Part 1 The Next Layer 2024-06-25 | In this livestream, we’re going to build an Enraged Rabbit Carrot Feeder (ERCF) V2 from FYSETC. You can pick one up here: jle.vi/ercfIf you enjoy the stream, feel free to send a “Super Thanks” or become a YouTube member / Patreon supporter: patreon.com/thenextlayer All proceeds go towards upgrading our equipment to make future videos better for you!⏯️ Part 2: youtube.com/live/Co3W5VFxB9c⏯️ Part 3: youtube.com/live/_jWXuMd0j_I⏯️ Part 4: youtube.com/live/nvVnp0WHYgI⏯️ Part 5: youtube.com/live/Zr068i7PzFw🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 PolyMaker: jle.vi/polymaker👉 FYSETC: jle.vi/fysetc👉 Voron Kits: jle.vi/voronkits🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #voron
Ep. 44: Ivan Trail, ERCF Team Member, on Open Source Multicolor Printing The Next Layer 2024-06-20 | In this video we’re joined by Ivan Trail. Brought to you by PCBWay (jle.vi/pcbway) and Kidoodle, the 3D Printer for Kids (bit.ly/3XooVSl).Ivan Trail is a member of the ERCF (Enraged Rabbit Carrot Feeder) team. former automotive and heavy equipment mechanic, machinist, and now an aircraft structures engineer. Ivan's path took a unique turn when he discovered his passion for 3D printing.Ivan's adventure began four years ago when his sons gifted him an Ender 3 for Christmas. Inspired by Jon from Proper Printing, Ivan quickly immersed himself in the world of 3D printing. This journey took a significant leap forward when he built a Voron 2.4 kit, transforming his hobby into a deeper passion for creating and upgrading 3D printers.In this episode, Ivan shares his experiences with various 3D printing projects, including his introduction to the ERCF and the creation of the "Twinsor." He talks about the challenges and triumphs he faced along the way, and how his persistence and innovation have led to significant advancements in 3D printing technology.🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 LINKS 🔗👉 FYSETC ERCFv2 Kit: jle.vi/ercf🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links ❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
I 3D Printed Viral Tools So You Dont Have To... The Next Layer 2024-06-18 | Save your filament! I tested out some of the most popular 3D Printed tools so you don't have to. Brought to you by Sovol. Check them out at jle.vi/sovol I love a good 3D Printed Tool - and functional 3d prints as a whole. The idea of being able to save money, time, and a trip to the hardware store, while getting EXACTLY the tool I want, in the color I want, with 3D Printable replacement parts when I inevitably break it? That, to me, is what 3D Printing is all about..But in the last couple of years, as printers have gotten significantly better (and design competitions have gotten significantly more rewarding), I've noticed a certain trend... functional 3D Print designs are getting more and more complicated, with many more parts, much more assembly, and much more filament required...In this video, we're going to take a look at some of the most popular, "advanced" 3D Printed Tools, and ask the question: are they worth your time, money, and most importantly... your filament?🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction02:04 Flexible Hose for Dust Extraction04:25 Table Saw FeatherBoard05:46 Solder Scroll07:42 Solder Flux Extruder09:54 LTT Screwdriver13:05 Mechanical Pencil15:13 Table Vise18:04 V-Roller Filament Spooler23:26 Summary & Conclusion🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Sunlu filament: jle.vi/sunlu👉 PolyMaker filament: jle.vi/polymaker👉 Kexcelled filament: kexcelled3d.com👉 Filamentech filament: https://www.filamentech.co.il/👉 Hex Drivers on AliExpress: https://s.click.aliexpress.com/e/_DmuVEoL or https://s.click.aliexpress.com/e/_DFxBZ3d👉 Carpenter Pencils I used to buy on AliExpress: https://s.click.aliexpress.com/e/_DF2FDET👉 My previous video about my 3D Printed Tools: youtu.be/Nb2JI1upCOU👉 My Filament Recycling Project: youtube.com/watch?v=Hm6KpEajD4o&list=PLNAIMkOXd_V_o9dkTBbgP9_CMdNdmOdwv🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Flexible Hose for Dust Extraction by Makers Manual on Printables: printables.com/model/820914-flexible-hose-for-dust-extraction🗿 Table Saw FeatherBoard by jcjames_13009 on Printables: printables.com/model/108962-featherboard-for-table-saw🗿 Solder Scroll by Victor on Printables: printables.com/model/843353-solder-scroll-ergonomic-adjustable-solder-tool🗿 Solder Flux Extruder by ftobler on Printables: printables.com/model/749093-soldering-flux-extruder🗿 LTT Screwdriver by CheffHD on Printables: printables.com/model/579899-ltt-screwdriver-with-ratchet🗿 Mechanical Pencil by MMM on Printables: printables.com/model/829522-pencil🗿 Table Vise by 3D anarchy on Maker World: makerworld.com/en/models/471299#profileId-380893🗿 V-Roller Filament Spooler by Fyrby Additive on Printables: printables.com/model/684376-v-spooler🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Ive Tried 200+ Filaments. These 20 Are The Nicest. The Next Layer 2024-06-11 | In this video, I talk about the 20 most beautiful filaments on the market right now. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!I don't know about you, but I still remember the days when "beautiful" filament meant a basic silk... or maybe, if you were lucky, a matte filament. But over the last few years, we've become spoiled for choice. Not only do we have sparkling colors, but we have dual silks, triple silks, silk gradients, matte gradients, fast transitions, slow transitions, textured filaments. We even have filaments with trippy iridescent effects.In this video, we're going to be exploring the MOST beautiful filaments to take YOUR 3D Printing projects from looking "common" to exquisite.So whether you're printing display pieces, toys, or even functional parts that you just want to be proud of... hold on to your wallets... because this video is going to be an expensive one to watch.🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction00:24 Background01:59 Fillamentum Wizard's Voodoo02:51 PolyMaker "Starlight" Series04:00 PolyMaker Galaxy Black05:42 Bambu Lab PLA-CF08:39 Sovol / eSUN Dual-Color Magenta Blue10:27 SliceWorx Matte Gradient Series11:13 ZIRO3D Matte Macaron Rainbow Gradient12:02 ZIRO3D Galaxy Gradient🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Fillamentum: jle.vi/fillamentum👉 PolyMaker: jle.vi/polymaker👉 Kexcelled: kexcelled3d.com👉 Bambu Lab: jle.vi/bambu (supports 3D Print General) 👉 Sovol: jle.vi/sovol👉 eSUN Dual-Color Magenta Blue: geni.us/eSUN-MagentaBlue [Amazon]👉 SliceWorx: sliceworx.com👉 ZIRO3D Matte Macaron Rainbow Gradient: geni.us/ZIRO3D-Rainbow [Amazon]👉 ZIRO3D Galaxy Gradient: geni.us/ZIRO3D-Galaxy [Amazon]👉 My previous video where I talked about Carbon Fiber filaments: youtu.be/WK-61N-dE8E🪨 Models Shown In This Video: 👉 printables.com/model/815231-the-lovi-short-vase-modern-and-unique-home-decor-f👉 printables.com/model/705509-piggy-bank-with-two-coin-slides-piggy-castle-bank 👉 printables.com/model/690437-the-manse-planter-pot-with-drainage-tray-stand-inc👉 printables.com/model/479363-tissue-box-refill-shorter-edition-remix👉 printables.com/model/853449-teddy-bear-keychain-small-bear-beautiful-gift👉 printables.com/model/889590-f-35-b-lightning-ii-with-landing-gears👉 printables.com/model/877693-articulated-demon-dragon👉 printables.com/model/516674-banana-for-scale🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Ep. 43: Gabe Bentz of Slant 3D on the Future of Manufacturing with Giant 3D Printer Farms The Next Layer 2024-06-07 | In this video we’re joined by Gabe Bentz of Slant 3D. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!Gabe Bentz is the founder and CEO of Slant 3D. Slant 3D is on a mission to make warehouses where the shelves make the product. By deploying giant 3D printer farms Slant 3D is able to produce real world products on demand and deliver them to customers.Gabe grew up on a cattle ranch, became a robotics engineer and against his will got involved with 3D printing.🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 CONNECT WITH GABE / SLANT 3D: 🔗👉 Subscribe to Slant 3D: youtube.com/@slant3d👉 Slant 3D: slant3d.com👉 Follow Slant 3D on X: https://x.com/Slant3D🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links ❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
The 30+ Most Anticipated 3D Printing Products Coming Soon The Next Layer 2024-06-04 | In this video, we're going to check out the most highly-anticipated new products coming to market in the 3D Printing Industry over the next few months. Brought to you by Sovol, makers of the SV08, SV07, and other high-quality, budget 3D Printers. Check them out at jle.vi/sovol Get excited! We're going on a tour-de-force - checking out over 30 of the latest and greatest new and highly anticipated products in consumer 3D printing. I've been hard at work digging up all the info, much of it unreleased until just now, from many of the biggest names in the industry. So in this video, we'll be taking a quick look at each upcoming product, including what we already know, the expected price, release date, and where you can find out more. In this video, we'll cover E3D, LDO Motors, AnyCubic, Creality, FYSETC, PolyMaker, WhamBam, Sunlu, and many, many more. I hope you enjoy it!🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:42 Creality & Creality K2 Plus03:31 LDO Motors & Positron V304:49 Sovol & Sovol SV0808:06 AnyCubic Kobra 308:32 FYSETC & ERCF V210:14 BigTreeTech / BIQU12:14 WHAMBAM12:51 E3D13:50 PolyMaker14:34 RatRig15:42 SUNLU17:15 Kexcelled17:47 SliceWorx19:32 Conclusion🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Creality: jle.vi/creality 👉 50% OFF K2 PLUS FOR THE FIRST 200 PEOPLE: jle.vi/k2plus 👉 CR-Scan Raptor Scanner: shrsl.com/4kc3m 👉 Falcon2 60W Pro-Safe Laser: shrsl.com/4kc3o👉 LDO Motors Retailer (USA): jle.vi/matterhackers👉 LDO Motors Retailer (EU/UK): jle.vi/voroneurope 👉 Sovol: jle.vi/sovol 👉 SV08 3D Printer: jle.vi/sv08 👉 Smoke Absorber: geni.us/sovol-smoke-absorber [Amazon] 👉 SH02 Filament Dryer: geni.us/sovol-sh02-filadryer [Amazon]👉 AnyCubic Kobra 3 Combo: jle.vi/kobra3👉 FYSETC: jle.vi/fysetc 👉 ERCF V2 jle.vi/ercf or shrsl.com/4kc2y 👉 LH Stinger V1.0 3D Printer Kit: https://s.click.aliexpress.com/e/_DBgU1VH or shrsl.com/4kc2w 👉 Prusa MMU3 Kit: https://s.click.aliexpress.com/e/_DEQfQ1p or shrsl.com/4kc2x 👉 BigTreeTech: jle.vi/bigtreetech 👉 Eddy: jle.vi/eddy 👉 HBB: jle.vi/hbb 👉 Panda Touch / K-Touch: jle.vi/pandatouch👉 WhamBam: jle.vi/whambam 👉 E3D: jle.vi/e3d👉 PolyMaker: jle.vi/polymaker👉 RatRig: ratrig.com👉 Sunlu: jle.vi/sunlu👉 Kexcelled: http://kexcelled3d.com👉 SliceWorx: sliceworx.com👉 Creality K2 Plus Multi-Color 3D Printer - A Game-Changer! by The Real Sam Prentice: youtube.com/watch?v=uXZC-94DI78&t=37s👉 My previous video about the LDO Positron V3: youtu.be/6qdbGFrwt8U👉 My previous video about the Sovol SV08: youtu.be/PlFH9bzdwQs👉 My previous video on how I "fixed" my Sovol SV08: youtu.be/BLZjbNOHCPk👉 My previous video about the AnyCubic Kobra 3 Combo: youtu.be/2CurchA4HT8🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a "Super Thanks" (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
AnyCubic Tries Multicolor: The AnyCubic Kobra 3 Combo The Next Layer 2024-05-29 | In this video, we're going to be checking out the AnyCubic Kobra 3 Combo multicolor 3D Printer. Brought to you by AnyCubic. Take advantage of introductory pricing ($449) and get an EXTRA $30 OFF with coupon code "AC30OFF" at jle.vi/kobra3In this video, we're going to be taking a look at the all-new AnyCubic Kobra 3 Combo... a multicolor 3D Printer combo which includes a filament dryer. I'll do some cool 3d prints, including some PETG ones and a handful of multicolor ones, and see how this 3d printer setup performs. Keep in mind that this printer hasn't shipped to consumers yet, so the software is far from ready. 🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction01:49 3D Benchy03:13 Multicolor Sea Turtle04:30 Skye from Paw Patrol Multicolor07:37 Multicolor PETG Makita Logo10:06 Multicolor ASA Tesla Sign12:33 The Verdict🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 PolyMaker: jle.vi/polymaker👉 Filamentech: https://www.filamentech.co.il/👉 Sunlu S4 Filament Dryer: jle.vi/sunlu👉 My factory tour at Anycubic: youtu.be/9XrUq1lDwnw🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 Articulated Sea Turtle by JD3D on Printables: printables.com/model/748459-articulated-sea-turtle-singlecolor-and-multicolor🗿 Skye from Paw Patrol by Gabor Gyarmati on Printables: printables.com/model/844540-skye-from-paw-patrol🗿 Makita Logo by d4av2n3 on Thingiverse: thingiverse.com/thing:4656369 🗿 Tesla Parking Sign by Mike Thomas on Printables: printables.com/model/452891-tesla-parking-sign🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a "Super Thanks" (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #anycubic #3dprinter #kobra3combo #3dprinting
I Upgraded the Sovol SV08 Till It Broke The Next Layer 2024-05-24 | In this video, I share how I "fixed" the Sovol SV08. Brought to you by Sovol. Check out the new Sovol SV08 at jle.vi/sv08THIS is the Sovol SV08. It's Sovol's "continuation" of the Voron 2.4... But unlike the Voron 2.4, it's designed to be mass-manufactured at scale and shipped almost entirely assembled. It also costs less than half as much as most Voron 2.4 kits. But is it as easy to modify, customize, and upgrade as a Voron 2.4? Can I really install all of these cutting-edge upgrades, most of which literally aren't even on the market yet....? And will the printer actually work at the end of the video...? Or have I bitten off way more than I can chew. Stick around till the end, and let's find out. 🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer 💬 JOIN MY DISCORD: jle.vi/tnl-discord🎥 IN THIS VIDEO: 🎥00:00 Introduction00:47 Background03:25 Fan Noise04:45 Touch Screen07:39 Build Plate08:48 Low Profile / Vibration Dampening Feet10:03 Z-Drift & Firmware12:16 Upgraded Hot End16:12 Upgraded Toolhead Board20:31 Eddy Coil Bed Sensor25:35 Conclusion & Next Steps...🔗 LINKS MENTIONED IN THE VIDEO: 🔗👉 Check out other Sovol printers and filament: jle.vi/sovol👉 E3D: e3d-online.com👉 BIGTREETECH K-Touch: shrsl.com/4jol7👉 WhamBam Flexible Build Plate: jle.vi/whambam👉 E3D Revo: jle.vi/e3d👉 V6 or V6 volcano compatible hot-end for the SV08 GitHub: github.com/Sovol3d/SV08👉 E3D Revo Heatsink Adapter for the Sovol SV08 on PCBWay Project Marketplace: pcbway.com/project/shareproject/E3D_Revo_Heatsink_Adapter_for_the_Sovol_SV08_fbe78f2f.html👉 BIGTREETECH EBB 36 and U2C Boards: shrsl.com/4joq5👉 BIGTREETECH Eddy: shrsl.com/4joqn👉 My previous video where I reviewed the Sovol SV08: youtu.be/PlFH9bzdwQs👉 My previous video where I build my 3D printer enclosure youtu.be/xQf55KmM1lI👉 Rav Meimad: https://en.ravmeimad.shop/👉 Filamentech: https://www.filamentech.co.il/👉 PolyMaker filament: jle.vi/polymaker👉 PCBWay: jle.vi/pcbway👉 Noctua fan on Amazon: geni.us/noctua60mmquietfan [Amazon]🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳 🗿 SOVOL SV08 Low Profile Vibration Isolation Feet! by 3DPrintDemon on Printables: printables.com/model/867321-sovol-sv08-low-profile-vibration-isolation-feet🗿 SV08 Foot pad by Synchro on Printables: printables.com/model/878833-sv08-foot-pad🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a "Super Thanks" (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Ep. 42: Thomas Haugen, The MakerViking, on Crafting Fun and Functional Projects for Makers The Next Layer 2024-05-24 | In this video we’re joined byThomas Haugen, the MakerViking. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!MakerViking, a Norwegian maker, is known for his contributions to 3D printing, including the Fenrir and Ymir printers. Drawing inspiration from his Viking heritage, MakerViking approaches his craft with respect for tradition and innovation.With a focus on practicality and functionality, MakerViking's designs aim to provide accessible tools and fun projects for fellow makers. He also explores digital sculpting, reflecting his passion for creativity and artistry.MakerViking shares exclusive content with supporters through his Patreon, where patrons can join him on his creative journey, download models, and gain access to behind-the-scenes insights. Additionally, MakerViking is an active member of the Thangs community, where he shares both his free designs and his exclusive content in his membership area.Inspired by the spirit of his Viking ancestors, MakerViking seeks to leave a meaningful legacy in the world of making. 🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 CONNECT WITH THOMAS / MAKERVIKING: 🔗👉 Subscribe to MakerViking: youtube.com/c/MakerViking👉 Support MakerViking on Patreon: patreon.com/makerviking👉 MakerViking on Thangs: thangs.com/designer/MakerViking👉 MakerViking on Printables: printables.com/@MakerViking👉 MakerViking: makerviking.com👉 Follow MakerViking on X: https://x.com/MakerViking👉 Follow MakerViking on Instagram: instagram.com/makerviking👉 Like MakerViking on Facebook: facebook.com/Makerviking🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links ❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
Ep. 41: Sonat Duyar on Revolutionizing Open-Source DIY Kits for 3D Printers and CNC Machines The Next Layer 2024-05-16 | In this video we’re joined by Sonat Duyar of Rat Rig. Brought to you by PCBWay. Register at jle.vi/pcbway and get a $5 welcome bonus!Sonat is a co-owner at Rat Rig, where he heads Marketing & Communication and hosts Rat Rig TV on YouTube, showcasing the latest in open-source DIY kits for 3D Printers and CNC Machines. Rat Rig champions a community-driven development model, closely engaging with users to swiftly evolve their products in line with emerging needs and trends. The company's commitment to an open modular platform allows for unparalleled customization and continuous upgradeability, making Rat Rig's machines renowned for their cutting-edge technology and superior performance.🤫 Get behind the scenes and exclusive content on my Patreon: patreon.com/thenextlayer💬 JOIN MY DISCORD: jle.vi/tnl-discord🔗 CONNECT WITH SONAT / RAT RIG: 🔗👉 Subscribe to Rat Rig TV: youtube.com/@ratrighardware👉 Rat Rig: ratrig.com👉 Follow Rat Rig on Facebook: facebook.com/ratrighardware👉 Follow Rat Rig on Instagram: instagram.com/rat.rig🛒 RECOMMENDED GEAR: 🛒📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing📍 Complete list of my videography gear: kit.co/jlevi/content-creation📍 My favorite 3D printing filament: jle.vi/polymaker📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted) 📍 My favorite BUDGET 3D printer right now: jle.vi/sovol📍 Check out the official TNL merch: shop.thenextlayer.com📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links ❤️ LOVED THIS VIDEO? ❤️▶️ Subscribe to the channel▶️ Watch my other videos: youtube.com/@thenextlayer 🔔 Turn on Notifications🎁 Support me on Patreon: patreon.com/thenextlayer🎁 Send a “Super Thanks” (Tip)🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links 💬 Join My Discord: jle.vi/tnl-discord ✍️ Write a comment below!👍🏿 Like this video#3dprinting #3dprinted #3dprinter
