Uploaded November 2020 | Updated September 2026, 3 weeks ago
2018-2020 F150 & Raptor Power Stop Z23 Complete Brake Kit (Electronic Parking Brake) K8026 - stage3motorsports.com/K8026-2018-2019-F150-Raptor-Power-Stop-Z23-Sport-Complete-Brake-Kit-Electronic-Parking-Brake.html
2015-2017 F150 & Raptor Power Stop Z36 Complete Brake Kit (Electronic Parking Brake) K6803-36 - stage3motorsports.com/K6803-36-2015-2017-F150-Raptor-Power-Stop-Z36-Extreme-Truck-Tow-Complete-Brake-Kit-Electronic-Parking-Brake.html
Shop All Powerstop Brakes - stage3motorsports.com/Power-Stop-Brakes.html
---------------------------------------------------------------------------------------------------------------------------------------
Front Brakes Factory Torque Specs
Caliper Anchor Plate Bolts: 184 lb-ft.
Caliper Guide Pin Bolts: 27 lb-ft.
Caliper Flow Bolt: 26 lb-ft.
Disc shield bolts: 159 lb-in.
Rear Brakes Factory Torque Specs (With Electronic Parking Brake)
Caliper Anchor Plate Bolts: 184 lb-ft.
Caliper Guide Pin Bolts: 27 lb-ft.
Rear Brakes Factory Torque Specs (Without Electronic Parking Brake)
Caliper Anchor Plate Bolts: 184 lb-ft.
Caliper Guide Pin Bolts: 24 lb-ft.
Electronic Parking Brake (EPB) Service Mode Activation
1. Set the ignition to ON.
2. Press and hold the accelerator pedal and place the EPB switch to the RELEASE (downward) position. Continue to hold the accelerator pedal and EPB.
3. Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.
4. NOTE: The EPB system will be deactivated, preventing parking brake application until service has been completed and service (maintenance) mode has been deactivated. The yellow EPB indicator will be illuminated and Maintenance Mode will display on the message center.
NOTE: When replacing rear brake pads in service (maintenance) mode, the brake caliper piston must be compressed into the caliper housing. The brake caliper piston does not have to be rotated while compressing the piston.
Set the ignition to OFF then release the accelerator pedal and EPB switch.
Electronic Parking Brake (EPB) Service Mode Deactivation
1. Set the ignition to ON.
2. Press and hold the accelerator pedal and place the EPB switch in the APPLY (upward) position. Continue to hold the accelerator pedal and the EPB switch.
3. Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.
4. NOTE: The EPB system will fully apply and release the parking brake to guarantee sufficient air gap between the rear brake pads and brake disc.
Release the accelerator pedal and the EPB switch
____________________________________________________________________________________
SUBSCRIBE AND FOLLOW
FB: facebook.com/Stage3motorsportscom
IG: instagram.com/stage3motorsports
Enter Stage 3’s latest giveaway: stage3motorsports.com/Giveaways.html
Never miss a thing when you join the Stage 3 Newsletter: stage3motorsports.com/Stage-3-Motorsports-Newsletter.html
Grab a Tee Shirt or Sticker - stage3motorsports.com/Stage-3-Motorsports-Gifts.html
2018-2020 F150 & Raptor Power Stop Z23 Complete Brake Kit (Electronic Parking Brake) K8026 - stage3motorsports.com/K8026-2018-2019-F150-Raptor-Power-Stop-Z23-Sport-Complete-Brake-Kit-Electronic-Parking-Brake.html
2015-2017 F150 & Raptor Power Stop Z36 Complete Brake Kit (Electronic Parking Brake) K6803-36 - stage3motorsports.com/K6803-36-2015-2017-F150-Raptor-Power-Stop-Z36-Extreme-Truck-Tow-Complete-Brake-Kit-Electronic-Parking-Brake.html
Shop All Powerstop Brakes - stage3motorsports.com/Power-Stop-Brakes.html
---------------------------------------------------------------------------------------------------------------------------------------
Front Brakes Factory Torque Specs
Caliper Anchor Plate Bolts: 184 lb-ft.
Caliper Guide Pin Bolts: 27 lb-ft.
Caliper Flow Bolt: 26 lb-ft.
Disc shield bolts: 159 lb-in.
Rear Brakes Factory Torque Specs (With Electronic Parking Brake)
Caliper Anchor Plate Bolts: 184 lb-ft.
Caliper Guide Pin Bolts: 27 lb-ft.
Rear Brakes Factory Torque Specs (Without Electronic Parking Brake)
Caliper Anchor Plate Bolts: 184 lb-ft.
Caliper Guide Pin Bolts: 24 lb-ft.
Electronic Parking Brake (EPB) Service Mode Activation
1. Set the ignition to ON.
2. Press and hold the accelerator pedal and place the EPB switch to the RELEASE (downward) position. Continue to hold the accelerator pedal and EPB.
3. Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.
4. NOTE: The EPB system will be deactivated, preventing parking brake application until service has been completed and service (maintenance) mode has been deactivated. The yellow EPB indicator will be illuminated and Maintenance Mode will display on the message center.
NOTE: When replacing rear brake pads in service (maintenance) mode, the brake caliper piston must be compressed into the caliper housing. The brake caliper piston does not have to be rotated while compressing the piston.
Set the ignition to OFF then release the accelerator pedal and EPB switch.
Electronic Parking Brake (EPB) Service Mode Deactivation
1. Set the ignition to ON.
2. Press and hold the accelerator pedal and place the EPB switch in the APPLY (upward) position. Continue to hold the accelerator pedal and the EPB switch.
3. Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.
4. NOTE: The EPB system will fully apply and release the parking brake to guarantee sufficient air gap between the rear brake pads and brake disc.
Release the accelerator pedal and the EPB switch
____________________________________________________________________________________
SUBSCRIBE AND FOLLOW
FB: facebook.com/Stage3motorsportscom
IG: instagram.com/stage3motorsports
Enter Stage 3’s latest giveaway: stage3motorsports.com/Giveaways.html
Never miss a thing when you join the Stage 3 Newsletter: stage3motorsports.com/Stage-3-Motorsports-Newsletter.html
Grab a Tee Shirt or Sticker - stage3motorsports.com/Stage-3-Motorsports-Gifts.html
