Uploaded October 2017 | Updated November 2026, 3 days ago
2013-2019 Ford Fusion Hybrid Inverter (SOBDMC/TCM)
0:00 Introduction
0:14 Various names for the inverter
1:20 Inverter liquid cooling and heat sinks
2:46 3 piece case
4:30 Smoothing capacitors
5:00 Water intrusion warning
5:55 Smoothing capacitor pre-charging
9:10 3-phase AC bus bars, current sensors, and connectors
12:23 Insulated Bi-Polar Transistors (IGBT)
16:50 High Voltage (HV) DC bus bars
17:16 High wattage resistor
20:00 IGBT module bracket and circuit board
23:40 Bottom cover installation
25:20 Connections to DC bus bar to smoothing capacitors
27:22 Reactor installation
28:18 Reactor boost inverter module
28:55 DC current sensor and bus bar
29:35 External HV DC battery and A/C compressor connection
29:55 HV interlock circuits and A/C compressor fuse
31:00 Installation of filter capacitors
31:55 Installation of 3 DC bus bars
35:20 Motor generator control computer bracket and circuit board installation
42:14 Upper case cover
43:19 Coolant expansion tank
45:30 HV 3-Phase cable connection
47:30 Converter location
Weber State University (WSU) - Department of Automotive Technology - Ardell Brown Technology Wing - Transmission Lab.
This episode covers High Voltage Hybrid Electrical Systems - Specifically the 2nd generation 2013-2016 Ford Fusion Hybrid Inverter, also known in Ford circles as the Secondary On-Board Diagnostic Module C (SOBDMC) or the Transmission Control Module (TCM).
The converter is located in the high voltage battery housing. Internal components and operations are discussed. The electrical operation of the Inverter will be covered in a future video in this series.
This topic is taught as part of our 4-year bachelor's degree program. For more information on the Weber Automotive program, visit: http://www.weber.edu/automotive
This video was created and edited by Professor John D. Kelly at WSU. For a full biography, see http://www.weber.edu/automotive/J_Kelly.html
2013-2019 Ford Fusion Hybrid Inverter (SOBDMC/TCM)
0:00 Introduction
0:14 Various names for the inverter
1:20 Inverter liquid cooling and heat sinks
2:46 3 piece case
4:30 Smoothing capacitors
5:00 Water intrusion warning
5:55 Smoothing capacitor pre-charging
9:10 3-phase AC bus bars, current sensors, and connectors
12:23 Insulated Bi-Polar Transistors (IGBT)
16:50 High Voltage (HV) DC bus bars
17:16 High wattage resistor
20:00 IGBT module bracket and circuit board
23:40 Bottom cover installation
25:20 Connections to DC bus bar to smoothing capacitors
27:22 Reactor installation
28:18 Reactor boost inverter module
28:55 DC current sensor and bus bar
29:35 External HV DC battery and A/C compressor connection
29:55 HV interlock circuits and A/C compressor fuse
31:00 Installation of filter capacitors
31:55 Installation of 3 DC bus bars
35:20 Motor generator control computer bracket and circuit board installation
42:14 Upper case cover
43:19 Coolant expansion tank
45:30 HV 3-Phase cable connection
47:30 Converter location
Weber State University (WSU) - Department of Automotive Technology - Ardell Brown Technology Wing - Transmission Lab.
This episode covers High Voltage Hybrid Electrical Systems - Specifically the 2nd generation 2013-2016 Ford Fusion Hybrid Inverter, also known in Ford circles as the Secondary On-Board Diagnostic Module C (SOBDMC) or the Transmission Control Module (TCM).
The converter is located in the high voltage battery housing. Internal components and operations are discussed. The electrical operation of the Inverter will be covered in a future video in this series.
This topic is taught as part of our 4-year bachelor's degree program. For more information on the Weber Automotive program, visit: http://www.weber.edu/automotive
This video was created and edited by Professor John D. Kelly at WSU. For a full biography, see http://www.weber.edu/automotive/J_Kelly.html










