V4 projectsI have completed the large 3D printer build! Larger prints will be presented in the next video.
Please note that this is a low budget build. I am not using the best components available. (by far). I am using whatever I already have or can get hold of as cheap as possible.
I followed up this PoC build with the new and improved RIFF 600/900 design. The cad for that version is available.
Some facts about the build: • Filament: Isanmate ASA (black), Fiberlogy ABS (light green) and SUNLU PETG (black) • Build plate 300 x 900 • 2020 and 2040 alu extrusions • SKR 1.4 turbo and SKR Pico controller boards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian • Klipper • Sensorless homing on X and Y • Dual Y stepper motors/drivers • Stealthburner • 3 x 360W power supplies • Dual mains switches/fuses
Timestamps: 00:00 Trollolo 00:18 Short recap 00:45 The completed printer 00:57 The outside explained 02:07 Thrustbearings 02:50 Kinematics 04:11 Electronics 05:57 Klipper config 07:32 Movement and first prints 07:45 Skippable? 10:01 Rough first print 10:22 A part for the Voronish 11:13 A cube 12:35 Heightmap
Large DIY 3D printer 2 - completing the buildV4 projects2025-04-09 | I have completed the large 3D printer build! Larger prints will be presented in the next video.
Please note that this is a low budget build. I am not using the best components available. (by far). I am using whatever I already have or can get hold of as cheap as possible.
I followed up this PoC build with the new and improved RIFF 600/900 design. The cad for that version is available.
Some facts about the build: • Filament: Isanmate ASA (black), Fiberlogy ABS (light green) and SUNLU PETG (black) • Build plate 300 x 900 • 2020 and 2040 alu extrusions • SKR 1.4 turbo and SKR Pico controller boards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian • Klipper • Sensorless homing on X and Y • Dual Y stepper motors/drivers • Stealthburner • 3 x 360W power supplies • Dual mains switches/fuses
Timestamps: 00:00 Trollolo 00:18 Short recap 00:45 The completed printer 00:57 The outside explained 02:07 Thrustbearings 02:50 Kinematics 04:11 Electronics 05:57 Klipper config 07:32 Movement and first prints 07:45 Skippable? 10:01 Rough first print 10:22 A part for the Voronish 11:13 A cube 12:35 Heightmap
#largeprinter #3dprint #DIYThe RIFF 600/900 3D printer 4 - config and motionV4 projects2025-08-23 | The RIFF is a large DIY printer that can be built without spending a fortune. You can build a 300x600 (RIFF 600) or 300x900 (RIFF 900) version of this. Custom files can be found on Printables. printables.com/model/1291703-the-riff-600900-large-3d-printer CAD model: github.com/itesdahl/RIFF
I generally encourage the use of second hand parts and will not provide any complete BOM listing specific new components.
I am not using the best components available. I am using whatever I already have or can get hold of second hand. No AWD, canbus, large controller boards or special stepper motors in this build.
Some facts about the build: • Filament used: Isanmate ASA (black), Filamentum ASA (RED) and SUNLU PETG (black) • Build plate 300 x 600 or 300x900 (using 2 or 3 pcs 300x300 heat beds) • 2020 and 2040 extrusions • SKR 1.4 turbo and SKR Pico controllerboards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian (the belts are a bit too long for corexy) • Klipper • Dual Y steppermotors • Sensorless homing on X and Y • Dragonburner with Sherpa micro • 2 x 360W 24V power supplies (3x 360W 24V in the 900 version)
Timestamps: 00:00 Trollolo 00:18 Wiring 02:37 Controllers 03:05 Radxa SBC rocks! 03:52 Installing Klipper 05:44 Just wow 07:19 Config file 08:55 Just buzzing 10:35 I don't do remakes...
#largeprinter #3dprint #DIYLarge 3D printer printing TPU #3dprinting #lowcost #3dprinter #DIYV4 projects2025-05-31 | You'll find some interesting DIY builds on the V4 projects channel.The RIFF 600/900 3D printer 3 - x and y axisV4 projects2025-05-27 | The RIFF is a large DIY printer that can be built without spending a fortune. You can build a 300x600 (RIFF 600) or 300x900 (RIFF 900) version of this. Custom files can be found on Printables. printables.com/model/1291703-the-riff-600900-large-3d-printer CAD model: github.com/itesdahl/RIFF
I encourage the use of second hand parts and will not provide any complete BOM listing specific new components. ---- Removing bearings from V wheels: youtu.be/r2sEQ9swdVk?t=963 The length of the x-axis extrusion is 440mm On my 600 build the 2020 extrusions for the bed assembly is 2 pcs 645mm. You have to check the bed mounts on your heat bed to determine if you need even longer extrusions in your build! ---- I am not using the best components available. I am using whatever I already have or can get hold of second hand. No AWD, canbus, large controller boards or special stepper motors in this build.
Some facts about the build: • Filament used: Isanmate ASA (black), Filamentum ASA (RED) and SUNLU PETG (black) • Build plate 300 x 600 or 300x900 (using 2 or 3 pcs 300x300 heat beds) • 2020 and 2040 extrusions • SKR 1.4 turbo and SKR Pico controllerboards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian (the belts are a bit too long for corexy) • Klipper • Dual Y steppermotors • Sensorless homing on X and Y • Dragonburner with Sherpa micro • 2 x 360W 24V power supplies (3x 360W 24V in the 900 version)
Timestamps: 00:00 Trollolo 00:18 Parts for the bed 00:59 Y axis 07:30 X axis 13:38 Installing the belts 17:40 Mistake corrected
I encourage the use of second hand parts and will not provide any complete BOM listing specific new components.
I am not using the best components available. I am using whatever I already have or can get hold of second hand. No AWD, canbus, large controller boards or special stepper motors in this build.
Some facts about the build: • Filament used: Isanmate ASA (black), Filamentum ASA (RED) and SUNLU PETG (black) • Build plate 300 x 600 or 300x900 (using 2 or 3 pcs 300x300 heat beds) • 2020 and 2040 extrusions • SKR 1.4 turbo and SKR Pico controllerboards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian (the belts are a bit too long for corexy) • Klipper • Dual Y steppermotors • Sensorless homing on X and Y • Dragonburner with Sherpa micro • 2 x 360W 24V power supplies (3x 360W 24V in the 900 version)
Timestamps: 00:00 Trollolo 00:18 More CAD 00:46 Skirts and covers 01:23 Scandinavian design vibes? 02:53 Custom parts 10:58 Heat bed assembly
I encourage the use of second hand parts and will not provide any complete BOM listing specific new components.
I am not using the best components available. I am using whatever I already have or can get hold of second hand. No AWD, canbus, large controller boards or special stepper motors in this build.
Some facts about the build: • Filament used: Isanmate ASA (black), Filamentum ASA (RED) and SUNLU PETG (black) • Build plate 300 x 600 or 300x900 (using 2 or 3 pcs 300x300 heat beds) • 2020 and 2040 extrusions • SKR 1.4 turbo and SKR Pico controllerboards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian (the belts are a bit too long for corexy) • Klipper • Dual Y steppermotors • Sensorless homing on X and Y • Dragonburner with Sherpa micro • 2 x 360W 24V power supplies (3x 360W 24V in the 900 version)
Timestamps: 00:00 Trollolo 00:18 What we are doing 01:42 Improvements 02:24 CAD for better or worse 05:59 Recycled and new 10:07 Building the frame 15:00 Size comparison 15:08 QC
#largeprinter #3dprint #DIYLarge DIY 3D printer 3 - calibration and printingV4 projects2025-04-22 | Doing some calibrations and largish test prints on the finished printer. It's working great!
Please note that this is a low budget build. I am not using the best components available. (by far). I am using whatever I already have or can get hold of as cheap as possible. I consider this printer a prototype/PoC.
I followed up this PoC build with the new and improved RIFF 600/900 design. The cad for that version is available.
Some facts about the build: • Filament: Isanmate ASA (black), Fiberlogy ABS (light green) and SUNLU PETG (black) • Build plate 300 x 900 (300x820 usable) • 2020 and 2040 alu extrusions • SKR 1.4 turbo and SKR Pico controllerboards • Radxa Rock 3C SBC • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian • Klipper • Sensorless homing on X and Y • Dual Y stepper motors/drivers • Stealthburner • 3 x 360W power supplies • Dual mains switches/fuses
Timestamps: 00:00 Trollolo 00:18 Clarifications 00:57 Basic calibrations 02:03 Input shaper 04:41 Graphs 04:50 Printing for the Voronish1 06:24 Printing a large frame 06:54 The 16h sub 08:38 Next project?
#largeprinter #3dprint #DIYLarge DIY 3D printer 1 - design and buildV4 projects2025-01-18 | I have always wanted a large 3D printer. So I’m building one!
Please note that this is a low budget build. I am not using the best components available. (by far). I am using whatever I already have or can get hold of as cheap as possible.
I followed up this PoC build with the new and improved RIFF 600/900 design. The cad for that version is available.
Some facts about the build: • Filament: Isanmate ASA (black), Fiberlogy ABS (light green) and SUNLU PETG (black) • Build plate 300 x 900 • 2020 and 2040 alu extrusions (i keep calling it 4020) • SKR 1.4 turbo and SKR Pico controllerboards • Orange Pi Zero 2 SBC (replaced by Radxa Rock 3C during the build) • MGN 12H rails/carriage on Y and X • 12mm rods and bearings on Z • Cartesian • Klipper • Sensorless homing on X • Dual Y stepper motors/drivers • Stealthburner • 3 x 360W power supplies • Dual mains switches/fuses
Timestamps: 00:00 Trollolo 00:18 Nice but smol 01:00 Design and the first frame 02:52 Kinematics and motion 03:55 Redesigned z-axis 04:54 X-axis 05:38 Electronics 08:05 Heatbed assembly 08:33 Toolhead and hotend
#largeprinter #3dprint #DIYDIY 3D printer - the complete buildV4 projects2024-12-20 | All the chapters/episodes of the Voronish 2 build compiled in one video.
Please note that some components changed during the build process
Timestamps: 00:00 Trollolo 00:18 Changes and improvements 01:36 Wiring 02:24 First power on 03:47 Checking motion 04:43 First print 04:50 Battle scars 07:30 Looking at the first print
#voron #3dprint #dragonburnerDIY 3D printer - part 4V4 projects2024-12-04 | The Voronish is a DIY 3D printer and a mix of Voron Trident and Voron 2.4 with some twists.
Isanmate filament supplied by Hobbytid.no (not sponsored, I paid for the filament).
Timestamps: 00:00 Trollolo 00:18 Useful comments 00:28 BFI and belts 01:52 Heated bed 04:09 Nozzle scrubber 04:47 Toolhead and hot end 09:32 Pi and Klipper 12:30 Information, not a warning 12:43 Stealing the files 13:07 An announcement and outro
#voron #3dprint #dragonburnerControl it from your phone!V4 projects2024-11-26 | This is a fun project for anyone with a 3D printer! I am using a Loco Remote controller and a mobile phone, but a motor, battery and simple on/off switch will do just fine for basic motion.
This is not a sponsored video. I paid for all components with my own money.
Loco Remote locoremote.co.uk PLEASE NOTE: Loco remote comes with a cable for Lipo and Power. I no longer had those around and had to improvise. I recommend using the original keyed connectors to avoid any mishaps.
Timestamps: 00:00 Trollolo 00:18 A fun project 01:04 Remote control 01:54 Building the chassis 02:27 Printed parts 02:44 Assembling the loco 04:40 A wonderful Santa 05:47 Detailing 06:42 A heavy wagon 08:18 Printing tracks 09:07 Testing, testing
#train #3dprint #christmasDYI 3D printer - part 3V4 projects2024-11-20 | The Voronish is a DIY 3D printer and a mix of Voron Trident and Voron 2.4 with some twists.
Glasscast resin supplied by Hobbytid.no (not sponsored, I paid for the resin and hardener).
Timestamps: 00:00 Trollolo 00:18 What are we doing? 00:28 Custom parts 00:48 XY joiner 01:25 Custom cover plates 01:44 The LemonBreeze Mega 01:54 Working with resin 04:30 The skirt 06:18 A/B drive 07:38 This is how it looks now 07:48 A timely delivery
#voron #3dprint #resinDIY 3D printer - part 2V4 projects2024-11-15 | The Voronish is a DIY 3D printer and a mix of Voron Trident and Voron 2.4 with some twists. The objective this time is to get the belted z-axis completed. Not easy without having all the parts, but I'll do it anyway!
Isanmate ASA supplied by Hobbytid.no (not sponsored, I paid for the filament).
Timestamps: 00:00 Trollolo 00:18 What are we doing? 00:34 Custom parts 03:25 A piece of advice 03:40 Front idlers for the gantry 04:30 Building the z drives 05:15 A bearing extraction tool? 12:16 Z belts 12:35 A bad path
#voron #3dprint #diyDYI 3D printer - part 1V4 projects2024-11-10 | This is part 1 of my DIY 3D printer build called "Voronish 2". In this first part I am presenting the concept, show the design in CAD and build the frame. And there is a bit of Icelandic in there.
Isanmate ASA supplied by Hobbytid.no (not sponsored, I paid for the filament).
This is not a monetized or sponsored channel. You can help me fund my future projects by using ko-fi.com/v4projects
Timestamps: 00:00 Trollolo 00:18 The concept 00:40 A sourcing guide for someone else 00:50 Some new and some recycled parts 01:16 CAD and the new frame design 05:27 Building the frame and spotting some mistakes 07:45 Icelandic challenge 09:43 In need of cosmetic surgery 11:27 Skipping steps... 11:43 What's in part 2? 11:50 Color scheme
#voron #3dprint #diyNew 3D printer build series coming soon!V4 projects2024-10-31 | I am looking at what to improve in the upcoming 3D printer build. Is it a "cunning plan" as Baldrick from "Blackadder" would say? Subscribe to follow this build!
This is not a monetized or sponsored channel. You can help me fund my future projects by using ko-fi.com/v4projects
Timestamps: 00:00 Trollolo 00:18 Back to the roots? 00:30 Rough plan in CAD 00:55 What should stay? 02:18 More for the parts bin 03:12 Components to be used 04:14 Filaments in the build 04:25 Tricky part? Maybe not. 04:40 Should have bought these?Adding a silicone nozzle scrubber and display to the not a Voron. Whats next?V4 projects2024-10-27 | The "not a Voron" series is finished and I need to move on. What's next?
This is not a monetized or sponsored channel. You can help me fund my future projects by using ko-fi.com/v4projects
Timestamps: 00:00 Trollolo 00:18 Basic tuning done 00:37 A brush for the nozzle 01:24 Getting the display working 01:47 Even more questionable parts 01:54 The not so promising heated bed 02:07 What's next? 02:35 Inspired by Cupra? (the car) 02:45 Please subscribe!
Resources mentioned in this video: github.com/scheffield/nozzle-cleanerIts not a Voron - and it’s finished!V4 projects2024-10-24 | This is part 6 of my 3D printer build. In this one I get to complete the printer and destroy some stuff as well. And I am doing my first few testprints.
Timestamps: 00:00 Trollolo 00:18 Todays agenda 00:43 Remixed SB adapter 01:10 A case for the Pico 01:22 A case and a fan for the Pi 01:37 Wiring and KISS 02:12 Calibration and configuration 02:36 No place like G28 (the first homing) 03:14 A minor disaster 03:58 Modest z-tilt 04:40 z-probe offset 04:54 My first bedmesh 05:25 Will it extrude? 05:36 The first print - no cheating! 06:56 Printing a first layer test 07:17 A stringy red benchy in PETG 07:55 A fun project with a lot of engagement from viewers 08:28 What to do with bad SD-cards 08:55 Working with resin again?
Timestamps: 00:00 Trollolo 00:18 Toolheads and extruders 01:06 A serious clog 01:40 Trying to be creative with resin 04:30 Choosing the hotend 05:45 Clockwork2 06:20 A bad clone 07:28 Dragonburner 08:26 A good idea? 08:44 A larger caddy 09:16 Not best practice 09:56 Klipper and the TMC error message 10:24 Dodgy pinout design 10:51 It's buzzing 11:24 What's next?
Timestamps: 00:00 Trollolo 00:18 Remember, it's scrap 00:44 New life for an old bed 01:20 Chains of plastic 01:39 Innovative? z endstop 03:05 A new mistake 03:18 Getting square 03:54 The useless pulley 04:04 Belts, belts, belts 05:16 A small miracle 05:46 A bad probe? 05:59 2016 is back 06:15 What about a Nitehawk? 06:24 Hotends in my scrap heap 06:37 A choice for part 5
Timestamps: 00:00 Trollolo 00:18 The parts are arriving 01:27 Steppers for Z 03:02 A small trick 03:33 Mounting z-steppers and gears to the frame 04:34 Rubber feet 04:54 My blunder and solution? 06:40 Checking the results of the redesign 07:00 Old PSU with a funky fanduct 07:32 Distributed MCUs and something practical 08:10 A strange build order 08:20 Corporate branding 08:37 AB drive with incorrect steppers 08:57 The build at the time of publishing.
Timestamps: 00:00 Trollolo 00:18 Recap and context 00:39 Mystery part 00:50 A bad choice of filament 01:16 Making accent color parts great again 01:35 Working in CAD 02:10 Preparing extrusions 02:34 Worst buy? 02:44 Jigs for the win 03:03 Not designed by accountants 03:28 Mystery part explained 03:53 Basic frame completed 04:03 Testing custom parts for Z 04:19 Stop thinking, follow the manual
Resources mentioned in this video vorondesign.com https://cnckitchen.store/ (not sponsored, I paid for everything)Its not a Voron - Part1V4 projects2024-09-17 | This is part 1 of what I hope will become a series of interesting videos about a cheap DIY 3D printer heavily "inspired" by the great Voron 3D printers. It could also become a complete disaster and a total waste of yours and my time :-)
I forgot to mention it in the video, but I will use 3 steppers on the Z-axis like the Trident.
Update: After getting some feedback about the esun ABS+ not being a good choice for functional parts. I have reprinted them in standard ABS.
Resources mentioned in this video vorondesign.com youtube.com/@kanrogcreationsA lighter toolhead with SherpaV4 projects2024-09-09 | My old DIY printer really needed some attention and I was pleasantly surprised by the print results after the makeover. It sort of went from slightly embarrassing to pretty good.
00:00 Trollolo 00:18 What we are doing this time 00:36 Orange Pi zero 2 01:41 Klipper newbie 02:15 Sherpa micro (sort of) 03:17 A safer power supply 03:39 A tempting next project?3D printed enclosures full range and subwooferV4 projects2024-08-18 | This took some time and effort, but I have finally made the system I was looking for. Great speakers with subwoofers on a low budget. Combining 3D printing and Jesmonite really works!
Thanks to hobbytid.no for supplying Jesmonite and Sunlu PLA and PETG (not sponsored, I paid for everything with my own money).
As Jesmonite is heavy you could use it in other 3D prints like in a base for a stand or as a counter balance. (more eco friendly than Lead at least)
Audio clips/samples starts at 08:30. The first part of each segment will be just the full range speaker, then I have added the subwoofers. You need to listen to this on a system that can reproduce some low end for any of this to make sense.
The Dayton full range drivers are very bright, and would benefit from EQ to dial back this tendency. The MarkAudio driver is overall better balanced, but lacks the "airiness" of the Daytons.
I would recommend the sub with 6,5" driver. The smaller sub works as well, but the 4" isn't capable of making it a "real" subwoofer. My choice is the vented Daytons with dialed back EQ combined with the larger sub.
Timestamps: 00:00 Trollolo 00:18 A status update 00:33 A three channel amp and low pass filter with dodgy psu 01:37 Subwoofers 02:18 Designing in Fusion 03:54 My first problem with AMS 05:12 Mixing Jesmonite 08:25 Steinway Grand Piano as a reference 08:43 Jazz quartet, switching speakers (no subwoofer). 09:31 Jazz quartet switching speakers and subwoofers. 10:43 Icelandic and catchy pop music from the Pandemic when most people stayed at home 11:20 Same, but with subwoofers 11:57 Outro. Would this be the last video on this channel? (no it wasn't)
Drivers used in these low budget speaker builds: Dayton PS95-8 3-1/2" full range driver: https://www.soundimports.eu/en/dayton-audio-ps95-8.html
Markaudio CHN-50 full range driver: https://www.soundimports.eu/en/markaudio-chn-50.html
Wiring terminal for backplate with 50mm cutout: aliexpress.com/item/1005006451323470.htmlGreat 3D printed speakers!V4 projects2024-07-27 | Finally I am getting somewhere! I need to build a small subwoofer (6,5" or 4" driver) to complement these speakers.
Timestamps: 00:00 Trollolo 00:18 The quest for better sound 00:36 Printing for hours and hours 01:23 Failed attempts 01:51 Finding a better speaker driver 02:04 Unboxing Dayton full range drivers 02:45 Redesigning in Fusion 03:12 No restrictions 03:52 intro to sound samples 04:04 Jazz quartet with a wonderful Steinway grand piano, switching speakers. 06:06 Female vocalist, my home recording 07:03 Conclusions and outro.
Dayton PS95-8 3-1/2" full range driver: https://www.soundimports.eu/en/dayton-audio-ps95-8.htmlShould you build a 3D printer?V4 projects2024-07-21 | This is a updated and hopefully improved video about this topic.
Links mentioned in the video: Thomas Sanladerer: "Building the cheapest possible Prusa i3 MK2 clone" youtube.com/watch?v=oVWLpvekby0
Desta3D "Bonsai 3D Printer" printables.com/model/97276-bonsai-3d-printer3D printed sound system - take 2V4 projects2024-06-19 | This is a follow up on the 3D printed sound system project. I made some changes based on suggestions in the comments. Did it work?
Thanks to hobbytid.no for supplying the Jesmonite. (not sponsored, I paid with my own money)
There will be part 3 to this series. I am waiting for some better speaker drivers!
STLs (from the part 3): printables.com/model/1062284-fullrange-and-subwoofers10 000 km med Toyota bZ4X (NOR)V4 projects2024-06-18 | Basert på 10 000 km over en vinter og vår med Toyota bZ4X ønsker jeg å dele mine erfaringer. I videoen sier jeg at jeg har "testet" mange andre elbiler. Jeg har hatt nevnte biler gjennom Fleks (nå nedlagt) og har hatt mulighet til å bruke alle disse bilene i minst en måned.
***Oppdatering etter 20 000km. Fortsatt ingen feil. Ingen vesentlige oppdateringer av programvare. Inntrykket fra de 10 000 første km er uendret. Er fortsatt strålende på vinterføre, men lader fortsatt frustrende sakte i kulde. Lader du hjemme, så har det siste ingen betydning.
*** Oppdatering etter ca 22 000km. Kompressor til klimaanlegg er byttet på garanti. Programvare til ECU er oppdatert og bilen ble vasket. Topp service fra Toyota!
*** Oppdatering etter 31 000km. Ingen feil, alt fungerer som det skal (bortsett fra en samtykkemelding som kommer opp igjen og igjen) og rutineservice er bestilt. Som del av planlagt service er det noe software som skal byttes, er spent på om det er merkbart for meg i daglig bruk.3D printed sound systemV4 projects2024-05-30 | This didn't work the way I wanted it to. But still, I got something good out of this. Audio clips are provided at the end of the video.
+ suitable power supply (12V-26V) and chassis connector3D printed trashcan PCV4 projects2024-05-21 | My 3D printed trashcan PC gets a matching drive. The warranty on the SSD probably isn't valid anymore after this :-)
3D model for the trashcan PC thingiverse.com/thing:30012473D print and wood catio - Part 2V4 projects2024-05-12 | When you resort to 3D printing to make your cat happy. I think it worked!3D print and wood catio - Part 1V4 projects2024-04-28 | When you resort to 3D printing to make your cat happy. Maybe.