DIY Faux Leather Journal from a Boot | Making a Bound Notebook from an Old Pair of Boots & Parchment Maker In Training 2018-02-12 | We made a DIY journal from up-cycled faux leather. We used old boots my wife was going to get rid of to make the outside binding of the notebook.The Process:We started by removing the faux leather from the old boots by cutting the stitches away with a precision hobby knife. Once the material was removed, we moved on to prepping the parchment paper. To give the journal a rustic look, we measured about a half an inch around each edge and tore the sheets. Once all the edges had the torn look, we split the sheets in half to get a smaller final page size. After folding all the sheets into booklets, we made a template and used an awl to poke the pages where we wanted the binding string to go. We then cut the faux leather to size making sure to allow room for overlap as well as a little extra to create the finished look. We took the additional step of finishing the edges by folding them over and using rubber cement to glue it in place. We then made waxed thread by taking some brown/tan cross-stitch tread and running over beeswax several times. The waxed string is a lot easier to work with. We then used the string and a needle to stitch all the pages into the leather cover. We finished the look by taking some of the buckles that were on the boots and stitching them to the journal. I followed the detailed instruction found here:youtube.com/watch?v=sRXjYxrsQeE If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe stuff we used:- Parchment Paperhttp://amzn.to/2H8wcMs (Affiliate)- Leatherman:http://amzn.to/2Gm1nDs (Affiliate)Safety Notes:Be careful when using a precision knife to cut think material like leather. (or faux leather) Music by iksonSoundcloud: soundcloud.com/iksonInstagram: @iksonofficialSpecific song - Reverie soundcloud.com/ikson/reverie-free-downloadMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
We turned his room into a POKE BALL!! Maker In Training 2021-03-07 | We recently bought a house and started renovating the rooms. My son got to choose how to paint his. The Process:We started by ripping up the carpet. I had to watch because Aaron was super excited to help and with all the carpet strips there were a lot of nails sticking up. With a little bit of careful instruction, we were able to make short work of it. We then moved on to prepping the walls. Since there was a lot of wall paper, we used a method of removing the vinyl coating and then soaking the paper underneath with a non-toxic wallpaper remover spray. (Link bellow) Once the walls were clean, we went on to patch up any holes that were left. We used some high hide primer to help cover up the dark blue since we were going to a lighter color. The short roller handle liked bellow is extendable which would have made it a lot nicer to paint with my son. The one we used came from a dust pan but did the trick. Once the painting was done we used a laser-level to guide the painters tape outlining. With that complete we finished up the red paint. Once complete we made sure to go over the entire floor checking for nails and staples that might wear through the laminate flooring we installed. The last step was to add the decals and get all the furniture put back. If you have read this far, awesome, let me know in the comments! : ) Get the decals here: amzn.to/3bUGHmOIf you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting us!https://www.Patreon.com/MakerinTrainingAlways use the right size tools for the job!Links to the product we used, or should have used. These are affiliate links so using these helps us out!Wallpaper Scraper: amzn.to/3reZ10c Extendable 3ft Pain Handle: amzn.to/3dZI06FNon-Toxic Gel Wallpaper remover: amzn.to/3q97f8TMusic and SFX provided by Epidemic sound:http://bit.ly/EPSOUNDOur Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Are we quitting because of COPPA? #COPPA Maker In Training 2020-01-07 | If you want to help keep me caffeinated, and my son full of gummies consider supporting us!https://www.Patreon.com/MakerinTrainingHow has COPPA affected you? What changes have you seen among creators? Let us know in the comments bellow! Don't forget to Like this video!The music we used in this video came from Epidemic Soundhttp://bit.ly/EpidemicSoundMiT (Referral link)If you are interested in more, please consider subscribing! youtube.com/makerintrainingMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
We planted some trees! Will you? #TeamTrees Maker In Training 2019-11-05 | Donate here on YouTube or head over to www.TeamTrees.org to donate!Lets plant 20 million trees together!!We had a blast planting these trees! We started by going to TeamTrees.org and donating $10, I matched the $5 that my son wanted to donate. Once we had those 10 trees planted, we decided to plant 3 more! This was a lot harder than expected just to plant three trees. We started by digging a hole that was one and a half times as big as the root ball and just a little shallower than the ball was tall. From what we were told you want to make sure your apple tree is planted at or just above the ground level. (But not bellow!!) Once the hole was dug, we roughed up the root ball before packing the ground back in around the tree. Once securely covered, we watered the tree slowly and thoroughly. Because our trees will be in an area that has a lot of white tail deer traffic as well as rabbit traffic we made sure to add some plastic corrugated pipe around the trunk. This will help deter animal damage for the first couple of years while the tree gets established.Follow all the #TeamTree Happenings over on these socials:facebook: facebook.com/teamtreesofficial instagram: @TeamTreesOfficialreddit: r/teamtrees twitter: @teamtreesofficlInfo about the Arbor Day Foundation:arborday.org/generalinfo/about.cfmIf you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, and my son full of gummies consider supporting us!https://www.Patreon.com/MakerinTrainingMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
We made a Star Wars Sandcastle! | Our Outer Banks, NC Vacation Project 2019 Maker In Training 2019-10-22 | We made an Epic Star Wars sandcastle modeled after the Death Star with some awesome tools from SandCastleTools.com(Sponsor). This was our outer banks vacation project video for 2019. We started by creating a solid base. We then used bucket forms to create the main volume of sand that we would be carving. We then followed the three basic rules for sand castle building: 1. Only use wet sand. 2. Build it like a pyramid. 3. Work from the top down.When we were done for the day, we made sure to leave the beach the same way we found it. : )If you are interested in the tools we used, head on over to SandCastleTools.com! Andy was super helpful with our order, and I know he will be with yours too! : )All the techniques we used can be found on Andy Hancock's channel:youtube.com/channel/UChFFnw4EU_26F6SWiAR6ZUg Prepping the buckets:youtube.com/watch?v=333gI3hSc1ICarving the Sand:youtube.com/watch?v=KHPRvJTO8LQUsing the Sand Shapers:youtube.com/watch?v=VQ2ttWG_lcI If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, and my son full of gummies consider supporting us!https://www.Patreon.com/MakerinTrainingSafety note: If you attempt this on your next vacation, make sure to fill the hole back up before leaving the area. : )Music by Silent PartnerMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
We made a REAL LIFE Minecraft Diamond Sword from Resin! In Real Life Maker In Training 2019-09-03 | We love Minecraft and so we decided to make a Diamond epoxy sword as a prop.The Process:We started by making molds for the epoxy blanks. Once the molds were made we mixed the epoxy and added pigments to it to shade it to the right color. (see links below) While the epoxy cured, we prepared the wood we used. Walnut, redwood, and maple were chosen since we had some on hand. With the wood ready to be planes, we de-molded the resin so that we could joint and plane the blanks. We ran every thing through the planner to make it all squared up. We then cut all the squares on the table saw. We used two part epoxy to glue it all together and finished it all up with some clear lacquer. Side note, the epoxy we used in this project was not the right one for the job. We should have used slow cure epoxy. If your interested in some, we have provided a link below to some awesome products from TotalBoat. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting us!https://www.Patreon.com/MakerinTrainingSafety note: Always wear a mask if you sand or cut epoxy. Fumes are not fun!Link to the product we used, or should have used. These are affiliate links:TotalBoat High Performance Resin: amzn.to/2lRn5JOTwo Part Epoxy: amzn.to/2koeTAkBlack Diamond Pigment: amzn.to/2lQ8Jt7Music by C418Song: Big Giant Circlessoundcloud.com/c418Our Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Making Custom LEGO Minifigures of Us! Maker In Training 2019-04-23 | We customized some LEGO figurines to create our minifigure doppelgangers.The Process:We started by picking what specific LEGO pieces we wanted to use and ordered them using the Bricklink website. To make the faces we decided to take some pictures of our faces so we could map out the features. Although we used Adobe Illustrator to do this, there are several free software packages that can be used. Inkscape is a good one to try. Once we mapped out what graphics to use, we made sure to scale them to the appropriate size and printed them out on clear decal paper. The decal paper needs a protective film over the ink so we applied a semi-gloss coat of clear paint. Once the paint dried we used some setting and solvent solutions made by a model company to aid in removing and installing the decals on the LEGO pieces. If you are interested in the products we used for this, there are links below. We purchased the LEGO pieces from Bricklink, a sort of eBay for LEGO. It is a great place to purchase the exact LEGO pieces you want. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting us!https://www.Patreon.com/MakerinTrainingSafety note: Be careful when playing with LEGO, its addicting. My Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
The Beatles - Abbey Road Spray Paint Album Art - Makers Rock 2019 #MakersRock Maker In Training 2019-03-13 | For #MakersRock 2019 I created a simplified spray paint version of The Beatles Iconic Abbey Road Album cover.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting us!https://www.Patreon.com/MakerinTrainingMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingMany other makers have created their own albums and every single one is up for grabs!Here's the full playlist of this years Makers Rock videos:youtube.com/playlist?list=PLe4fv0PmAAkFVcovW-fpgs9QImOfP_6gKHere are all the previouse years:2016 - youtube.com/playlist?list=PLe4fv0PmAAkGqs5_cDJgOO625jOvxSAWi2017 - youtube.com/playlist?list=PLe4fv0PmAAkEysGAOKQOsOjB9hOLZqQEo2018 - youtube.com/playlist?list=PLe4fv0PmAAkHqMtA8cDIZsMZcKT-4Km7STo enter my free giveaway, just sing up using the link below:http://bit.ly/MakersRockYou can also enter the giveaways on other channels so make sure to go check them out in the links below!Direct links to all Makers Rock participants:Billy Burthttps://youtube.com/channel/UCk6YGwd7...Catharine Hoehnyoutube.com/ParadiseBeachWeddingCy’s Cornerhttps://www.youtube.com/channel/UCOoe...Dave Gattonhttps://youtube.com/channel/UC2tIa58o...Dave.G.Designsyoutube.com/davegdesignsDesertBum WoodWork’nyoutube.com/DesertBumWoodWorknDriveway Workshopyoutube.com/drivewayworkshopFrankie’s CNC & Woodworking Channelhttps://youtube.com/channel/UCwzrreYs...FUN WITH WOODWORKINGyoutube.com/FunWithWoodworkingHerb Lichtenbergyoutube.com/herblichtenbergJen Spiceyoutube.com/jenspiceJK’s Timber Scrapsyoutube.com/jpgooberJohn Clothierhttps://youtube.com/channel/UC2hWlsf1...John Clothierhttps://youtube.com/channel/UC2hWlsf1...Know What Mom Knowsyoutube.com/knowwhatmomknowsMake it Sophhttps://youtube.com/channel/UCy2WZ1h9...Maker in Trainingyoutube.com/MakerinTrainingMiter Mike’s Woodshopyoutube.com/mitermikeswoodshopOdessa Woodworking and Maker Shopyoutube.com/kilroy79763Paul John’s Lifeyoutube.com/pauljohnslifeSin City Soap and Candleshttps://www.youtube.com/channel/UCfv-...SoCoMO Woodworkhttps://youtube.com/channel/UCCxyDRJw...Steve Carmichaelyoutube.com/carmichaelworkshopTempleboy Turningsyoutube.com/stevo15771The Mad Makeryoutube.com/TheMadMakerWallman Woodshopyoutube.com/wallmanwoodshopWaylight Creationshttps://youtube.com/channel/UC38CQXaE...WHCreationsyoutube.com/WHCreationsWoodifiedyoutube.com/woodified
DIY Floor Lamp using an old Walmart light Maker In Training 2019-02-06 | We remade our cheap Walmart floor lamp, steampunk style! This is a really easy was to spruce up an old lamp, or just create a new one from scratch! : )The Process:We started by breaking down the old floor lamp so that we could use some of the components. We removed all the electrical wiring and salvaged what we could. We kept the main head of the lamp and the arm section. Once torn down, we attempted to reuse the base but found out that it would not be possible given the fact that it started to break as we tried to drill it for the base conduit piece. We ended up using a weightlifting weight as the base and use some high strength epoxy to secure the conduit coupling to the base. We then used standard conduit and a junction box to make up the rest of the lamp. Once it was all assembled the junction box made a perfect location for all the wiring to come together. We used some steel fencing wire to create the "shades". We painted it all a bronze color and topped it all off with some LED Edison style bulbs.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting us!https://www.Patreon.com/MakerinTrainingSafety note: Be careful when using a grinder, make sure to use safety glasses or a face shield.My Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
5000 Sub Live Stream Celebration!! Maker In Training 2018-11-02 | We are doing a live stream celebrating all of you that subscribed!We will be giving away some awesome stuff and answering your questions!! Come hang out with us! : )The LEGO set we are building. . . :LEGO Marvel Super Heroes Avengers: Infinity War Thanos: Ultimate Battle 76107http://bit.ly/LEGOSetLive (Affiliate)If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting me!https://www.Patreon.com/MakerinTrainingMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
5000 Subscriber Celebration & Live Stream Announcement Maker In Training 2018-11-01 | We are doing a live stream celebrating all of you that subscribed!Live stream will be November 3rd @ 9AM EST. : ) See you there!!We will be giving away some awesome stuff and answering your questions!! Come hang out with us! :)The LEGO set we will be building. . . :LEGO Marvel Super Heroes Avengers: Infinity War Thanos: Ultimate Battle 76107http://bit.ly/LEGOSetLive (Affiliate)If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting me!https://www.Patreon.com/MakerinTrainingMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Steel and Pine Hammock Stand | Building a Sturdy Hammock Holder Maker In Training 2018-09-03 | We made a hammock stand from steel and treated pine. This hammock stand is sturdy, stable, and easy to make. We followed Peter Brown's design for this build.It can be found on his Shop Time video entitled Steel & Redwood Hammock Stand:youtube.com/watch?v=s5YFgjx1hrA The Process:We started by getting two pieces of steel from our local welding shop. Both pieces were pre-cut to two feet in length. We cut each one into two four inch pieces and then measure seven inches from each end placing a sixty degree line between the measurements. We then cut all the pieces using a grinder and cutoff wheel. We tried using a reciprocating saw, and although it did work, it was hard to control and keep straight. Once the steel was cut, we cleaned all the pieces, again using the grinder, but this time with a flap sanding disk. We then used an arc welder to weld all the pieces making sure to tack one side first to prevent warping. We then cleaned up the metal and painted the brackets with primer, and then black paint. We drilled four half-inch holes, one for each arm. We then bought four by four treated lumber from our local hardware store. We purchase two eight foot long pieces, and two six foot long pieces. We cut two foot sections (four of them) out of one of the eight foot long pieces. We then stained all the pieces using dark wood stain. We should have used exterior grade stain, but we didn't want to make another trip to the store. We then assembled it all using bolts and washers. Finally, we enjoyed our hammock stand. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated (and my son full of gummies), consider supporting me!https://www.Patreon.com/MakerinTrainingSafety note: Be careful with metal working/welding, seek help if its new to you.Music by Jeremy BlakeSong: Exhaleyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTraingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
Wooden Patio Ice Chest Cooler | A Project made from inexpensive 2x4 Maker In Training 2018-08-05 | We made an ice chest cooler from inexpensive 2x4 lumber. This is a great vacation or weekend project and makes a great addition to any patio or deck.The design for this deck cooler came from a video by DIY PETE. We have included a link to his video below. We started by figuring out how tall we wanted the cooler to sit. Then we cut down the 2x4s to size. Once cut to size, we secured the legs with pocket holes. (Link to the inexpensive jig we used below). We then removed any excess part of the cooler. (handles, lid pins, etc.) Once cleaned up, the cooler was measure for size. We made a base platform for the cooler to sit on and the screwed it all together adding a top as well. Once the framework was built, we sanded and stained all the wood. We created paneling by resawing the 2x4 s along the width. We used wood glue and a pin nailer to secure the paneling. We then made the lid portion following the same patter: Measure, build framework, and add paneling. We secured the top wood to the cooler lid using some long screws. We then finished the entire project with some polyurethane, added the hardware, and called it a day. : )If you enjoyed the video please give it a like and let me know your thoughts in the comments below. All the techniques we used and a more detailed explanation can be found in DIY PETE's build video.DIY PETE's vidoe:youtu.be/1A96fGXS2UMDIY PETE's channel:youtube.com/channel/UCEAY1udDi0HBnu7BbxDsJUgThe Kreg Jig for making the pocket holes:http://bit.ly/pockthl (Affiliate)If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, consider supporting me!https://www.Patreon.com/MakerinTrainingMusic by Joakim KarudYouTube: http://youtube.com/joakimkarudSoundCloud: soundcloud.com/joakimkarudMusic by Otis McDonaldSong: You're not that funnyyoutube.com/audiolibrary/musicMusic by Diamond OrtizSong: 8 Year Anniversaryyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
How to Make an Epic Sand Castle with Simple Tools | Our Outer Banks, NC Vacation Project 2018 Maker In Training 2018-06-17 | We made an epic sand castle using buckets and cheap tools you can find at the local store. This was our outer banks vacation project video. We started by creating a solid base. We then used bucket forms to create the main volume of sand that we would be carving. We then followed the three basic rules for sand castle building: 1. Only use wet sand. 2. Build it like a pyramid. 3. Work from the top down.When we were done for the day, we made sure to leave the beach the same way we found it. : )All the techniques we used can be found on Andy Hancock's channel:youtube.com/channel/UChFFnw4EU_26F6SWiAR6ZUg Prepping the buckets:youtube.com/watch?v=333gI3hSc1ICarving the Sand:youtube.com/watch?v=KHPRvJTO8LQIf you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, consider supporting me!https://www.Patreon.com/MakerinTrainingSafety note: If you attempt this on your next vacation, make sure to fill the hole back up before leaving the area. : )Music by Joakim KarudYouTube: http://youtube.com/joakimkarudSoundCloud: soundcloud.com/joakimkarudSong: Mondayssoundcloud.com/joakimkarud/mondaysMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
Concrete and Copper Wind Chimes | QUIKRETE® One Bag Wonder 3.0 Contest #Quikrete1bagwonder Maker In Training 2018-06-05 | We made some concrete wind chimes using a single bag of QUIKRETE®. Although they don't really work, the result is quite unique. This was our entry into the #Quikrete1bagwonder challengeThe Process:We used Quikrete fast setting concrete for this project. We also used PVC pipe both 1” and 2” to make the forms. We measure the desired length and then cut the pipes to size making sure the keep the 1” pipes longer (about 2” longer). We covered the outside of the 1” pipes with plastic wrap and the inside of the 2” pipes with vegetable oil. Both the plastic wrap and the oil was to allow the concrete to release easier. We used thick copper wire to form the hanger loops. When we mixed and poured the concrete, we used a sander to vibrate the forms to help settle out the bubbles. Once the concrete set up, we cut grooves in the outer forms to allow them to break free. We used some copper flashing to create bands on each of the hanging “bells”. We finished the project off with some black paracord as the main hanger cord. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, consider supporting me!https://www.Patreon.com/MakerinTrainingOriginal announcement video:youtube.com/watch?v=vx11JPIpM4oSafety Notes:Wear a dust mask when working with concrete indoors. Don't want to be breathing that dust. . . : )Music by VexentoSong: Standing Stillsoundcloud.com/vexento/vexento-still-standingyoutube.com/Vexentosoundcloud.com/vexentoMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTraining
How to Make DIY Yard Dice | #RocklerPlywoodChallenge | One Sheet of Plywood Maker In Training 2018-06-01 | We made a set of Yard Dice from plywood. This is our companion video to our entry into the #RocklerPlywoodChallenge put on by the Modern Maker Podcast. This is a simple DIY project that is great for summer.The Process:We started by cutting down the plywood into thin strips the width of the dice we wanted to make. We then cut the strips to make squares, six for each die. We then added a forty five degree chamfer to the squares by cutting them with the table saw. Once cut and chamfered, we then glued them together to form the die body. We then marked out where we wanted the dots to go so that it was easier to locate later. We then used a router and a round-over bit to round the edges of each die to make it smoother. Using a propane torch and a round bolt head, we burned the dots onto the dice. We finished them off with some light sanding and a coat of clear satin polycrylic to keep the natural color of the wood. The finish we used: Water-Based Polycrylic Clear Sprayamzn.to/2H5xCHL (Affiliate)If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, consider supporting me!https://www.Patreon.com/MakerinTrainingModern Maker Podcast Channel:youtube.com/channel/UCdc9iEHKuyUNTGQNIpb0zYA/feedSafety Notes:If you plan on burning wood, make sure to do it in a well ventilated area and have a fire extinguisher close by. . . Music by VexentoSong: Attention Deficityoutube.com/Vexentosoundcloud.com/vexentoMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
DIY Glass Whiteboard | Making a Modern Style Dry Erase Board using Up-cycled Glass and Pallet Wood Maker In Training 2018-04-18 | We made a modern style whiteboard using recycled glass and some leftover pallet wood. This is a simple DIY project that only requires the most basic of power tools.The Process:We started by cutting down some pallet wood we had leftover from some other projects. Using the table saw we cut the wood down to size. We then determined how thick of a slot to make by measuring the glass thickness. We were able to make two passes with the table saw to make the slot. We then sanded the wood and used some black spray paint to finish it off. We also painted the head of the screws to make sure they didn't show once the boards were installed. We then installed the board by first leveling and installing the bottom board. then using the glass as a spacer, we marked where the second board should go. All that was left was to slide the glass into place. We used some liquid chalk pens (Link below) to draw on the board and they worked great! If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, consider supporting me!https://www.Patreon.com/MakerinTrainingThe stuff we used:- Liquid Chalk Markers:http://bit.ly/ChalkMkr (Affiliate)Safety Notes:Be careful when working with tempered glass. Don't drop it, it could shatter. . . Music by Silent PartnerSong: Get Backyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
DIY Hanging Succulent Shelf with Mugs | Making Home Decor with Walmart Cactus & Salvation Army Cups Maker In Training 2018-04-03 | We made a wooden hanging shelf for some cactus we bought at Walmart using reclaimed mugs from the Salvation Army Store.The Process:We started by going to our local thrift store and getting a few mugs that we thought would compliment the cacti. We then used a piece of wood we already had which was the right shape and size for this project. We marked the locations where we wanted the mugs to sit making sure they were spaced appropriately to account for the handles. We then created inset locations by using some really large forstner bits. We also drilled locations for the rope to pass through. Once all the holes were drilled, we sanded the entire piece of wood and used some clear spray lacquer to seal up the board (Link below). We then threaded some twisted sisal rope through the side holes so that we could hang then entire project in our desired location. Finally, we replanted the cacti into the mugs and placed them on the board. This was a very simple project that can easily be completed at home. I have included links to most of the materials I used in this project.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingIf you want to help keep me caffeinated, consider supporting me!https://www.Patreon.com/MakerinTrainingThe stuff we used:- Water-Based Polycrylic Clear Sprayamzn.to/2H5xCHL (Affiliate)- 3/8 Sisol Ropeamzn.to/2GLn435 (Affiliate)- Leatherman I own and love:http://amzn.to/2Gm1nDs (Affiliate)Safety Notes:Be careful when replanting cacti, wear gloves to protect from getting poked! : )Music by VexentoSoundcloud: soundcloud.com/VexentoSpecific song - ChippyMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Homemade Three Man Tandem Bicycle | A Freak Bike inspired by Lauras Beastbike Maker In Training 2018-03-19 | We made a three man freak bike!! After watching one of Laura Kampf's freak bikes, my son told me he wanted a bike that "Mom, Daddy, and me" could ride together. This is what we came up with.We started by gathering a bunch of bikes from friends. Most of them were rusted and in bad shape. We were able to find a city bike, a mountain bike, and a toddler bike. We decided to put the toddler bike in the middle so that most of the weight would be towards the tires of each outer bike. Since we do not have a lot of experience welding, we opted for bolts and steel bars as the main support for the build. We started by welding the front pivot points of the two inner bikes fast so as to keep them from moving. We then welded bolts to the forks of the bikes at each attachment point. That completed the limited welding needed. We then drilled holes in all the bikes as well as some steel bars so that we could install braces. We rand long bolts through the forks of each bike and through the top bars and tightened everything. We then finished it all with a coat of paint. it took four chains to make the pan needed!! If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing and maybe even supporting me on Patreon! youtube.com/makerintrainingpatreon.com/MakerinTrainingSafety Notes:The guard was not installed on the grinder I was using. . . Never do this! Always use the provided safety measure. Kids should be supervised in the shop at all times. My son and I make sure all power tools he uses are unplugged.Music by Diamond OrtizSong: Inevitableyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Ironclad Remote-Controlled Car Mod | My entry into Jairus of Alls #WorldsgreatestRCCarChallenge2018 Maker In Training 2018-03-01 | This is my entry into Jairus of All's RC Car Challenge #WorldsGreatestRCCarChallenge2018 I clad an RC car in Iron! (Ok, thin steel but close enough!) I used a simple RC car my son had for this project. We started by first removing the shell from the RC car. We then removed the back wheelie wheel rotated it and replaced it so that the new shell would clear it. Once that was done, we created a template using some crap cardboard. Using the newly created template, we marked some crap sheet metal left over from a satellite dish. We then cut it out using a grinder. Once the pieces were cut out, we used a welder and carefully welded all the pieces together. We then painted everything with a flat black paint. While the paint was still dry, we weathered the outside metal. Finally we attached the outer shell to the RC car using some fast drying two part epoxy. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing and maybe even supporting me on Patreon! youtube.com/makerintrainingpatreon.com/MakerinTrainingEpoxy I used:Devcon 20945 S-209 High Strength 5-Minute® Fast Drying Epoxyhttp://amzn.to/2C6rsnk (Affiliate)Safety Notes:The guard was not installed on the grinder I was using. . . Never do this! Always use the provided safety measure.Music by Diamond OrtizSong: Cubic Zyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Screen Printed Patch the Poor Mans Way | Making a Patch From my Old Sweater Using Puffy 3D Paint Maker In Training 2018-01-28 | We screen printed a patch to use on our new hoodies. We used my old hoodie as the patch material as well as some Puffy 3D Paint.The Process:We started by getting an old screen door screen and a dollar store frame. We cut the screen to size and used some masking tape to cover the entire screen. We printed out the design we wanted to screen print and cut it out. We then attached the design to the masked off screen to give us a template to follow. We then cut out the masking tape using the template as a guide making sure not to cut through the screen. (Just cutting through the masking tape) Once the design was cut out, we taped the screen to the frame. We made a guide to follow right on the table we were using. (I had a scrap piece of MDF as a work surface) We then used the guide to position the piece we wanted to screen print. In our case, it was a cut out piece of my old hoodie. Once positioned, we used Puffy 3D Paint as our "Screen Print Ink". (Link below for where to get it) We used some cheap putty knives to spread the "ink" around. Once spread out evenly, we removed the screen leaving behind only the paint that was on the exposed screen. After letting it dry, we used some HeatnBond (Link below) to Bond the Patch to our new shop hoodies. : )If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe stuff we used (Affiliate):- Puffy 3D Painthttp://bit.ly/Puffy3DPaint- Thermoweb Heat'n Bond Ultra Hold Iron-On Adhesive http://amzn.to/2AC90Dw- Leatherman Wingmanhttp://amzn.to/2Gm1nDsSafety Notes:Irons are hot. . . These should be used with supervision. : )Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comSong: Coyotesoundcloud.com/vexento/vexento-coyote-1youtube.com/watch?v=cqFIMTGa8kYMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://www.Patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Barn Door Hardware Installation | Making a Sliding Pantry Door from a Reclaimed Barn Door Maker In Training 2018-01-15 | I made a sliding pantry door using Amazon hardware (Link below) and a barn door I reclaimed from an old barn.The Process:I started by getting an old barn door. The barn door in question was from a family barn that was slated to be torn down. Once recovered, I used a brush mounted on a drill to brush off all the loose bits of dirt, grim, and wood. Once it was all brushed off, I used a sander to knock off the edges so that the wood would feel nice to the touch. I then applied three coats of Polycrylic. (Link below) The Polycrylic is water based, dries quickly, and comes out clear which makes it ideal. I then mounted the hardware making sure to follow the included instructions. I made sure the mounting points were in studs so that it would support the weight of the door when installed. Once the door was mounted, I notice that the door would drag against the wall so I installed a modified caster as a spacer and for the door to ride along. I think the project turned out great!I have provided links to the hardware and materials used to do this project. Unfortunately I could not find authentic barn doors on Amazon. I think this will need to be sourced locally. : )If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe stuff we used:- Barn Door Hardware I usedhttp://amzn.to/2DdYR3z (Affiliate)- Minwax Polycrylic Protective Finish (Satin)http://amzn.to/2mug9iz (Affiliate)Safety Notes:Barn doors are heavy, I made sure the bolts were going into studs when installing the hardware given the weight of the door. Double check the weight limit of the hardware and the weight of the door before attempting this!Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comSong: Lightssoundcloud.com/vexento/vexento-lightsyoutube.com/watch?v=MXKkMJVtOOQMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Copper Drink Stirrers | Making Cocktail Stirrers From Electrical Wire And Marbles | Glass Markers Maker In Training 2018-01-02 | I made some copper cocktail drink stirrers using electrical wire and marbles. This would also make great drink markersThe Process:I started by removing the insulation form the wire. I then used a small hammer to straighten the wire. I then bent the wire back and forth using some round nose pliers (Link below). I then used a drinking glass to measure the right depth needed for the stirrer and bent a ninety degree bend at that spot. I then coiled the wire increasing the coil until it was about the diameter of the marble I wanted to use. I then placed the marble into the coil and finished wrapping the wire. I then cut and filed the end of the wire and used the round nose pliers to bent the final curl. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you would like to support what I do, check out my Patreon: patreon.com/MakerinTrainingIf you are interested in more, please consider subscribing! youtube.com/makerintrainingPliers I use:- Cousin Precision Comfort 3-in-1 Plier for Jewelry Makinghttp://amzn.to/2j9ifU8 (Affiliate)Safety Notes:Acording to the FDA, Copper should not be used in drinks that have a PH below 6.0. Use another non reactive material such as stainless steel. Long before you reach the highest levels of copper in a beverage, the drink gets a metallic taste. Music by Ehrling:soundcloud.com/ehrlingehrlingmusic.wordpress.comSong:You And Mesoundcloud.com/ehrling/ehrling-you-and-meMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Elephant Fork Bracelet | Making a Jewelry piece from Goodwill cutlery | Metalworking Stainless Steel Maker In Training 2018-01-01 | I made a metal stainless steel bracelet using silverware I got at the local Goodwill. This is a very simple up-cycle project to make!The Process:I started by heading to my local Goodwill and picking up some forks. They cost me all of twenty cents each. You could always use ones out of your kitchen, but that's up to you. The first step in making this project involved flattening the piece to be worked. I attempted to punch a small dimple into the fork about where I wanted the eye to go. I guess the nail I was using was a little softer than the fork. I resorted to drilling instead. I then took the flattened piece and cut three of the tines off the fork leaving a little bit on each one. These bits will become the feet. I followed that by attempting to bend the last tine into shape. I was planning on making a very ornate bend and twist to make the trunk long and curly, but the metal was brittle and snapped when I tried to do it cold. I had to heat the bit that was leftover with a propane torch to get it to bend in to shape. I decided to file a little round into the end to make it look more like a trunk. I finished it all up but bending the main fork body into a bracelet shape and polishing it all up with some abrasive pads.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you want to support what I do, Patreon is the best place to do that:patreon.com/MakerinTrainingIf you are interested in more, please consider subscribing! youtube.com/makerintrainingSafety Notes:Fire. . . yea, respect it!Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comSong: We are onesoundcloud.com/vexento/vexento-we-are-oneyoutube.com/watch?v=2N4t_kChuiUMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon:patreon.com/MakerinTraining
Brass Ice Pick | Making a DIRESTA Inspired Ice Pick on a Metal Lathe | My First Lathe Project Maker In Training 2017-12-31 | We made a brass ice pick inspired by Jimmy Diresta's ice pick. This was made in Trevor Higgins' shop and was my first lathe project. (Link Below)The Process:We started by collecting all the raw materials needed: Brass bar stock, brass tube stock, a brass ring, and some hard steel for the pick. We then cut the stock to length. I used DustySqueak's ice pick as an example for length. We then machined the ice pick on the lathe starting with facing one side. we then flipped the bar end to end and machined the taper. We then knurled about an inch or two to three centimeters to give the pick a grip section. We then prepped the cap. We took the tube stock and filed a divet in the end to accept the brass ring we chose. Using plumbing solder and a torch, we joined both the ring and the tube together. We used a grinder to create a rough point on the steel and then filed the final finish on it. We used super glue to join the point to the base and finished it all off with some abrasive pads and polish to give it a nice finish.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingTrevor Higgins' Channel:youtube.com/channel/UCl4uJHqZiMWO8kSF4m4QsvwSafety Notes:A lathe is a great tool! With great tools comes great responsibility. Don't use a tool you are unfamiliar with. This was my first time using a lathe and I had someone there to teach me and keep an eye on me while I worked. A skilled teach is invaluable and one of the safest ways to work.Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comSong - Trippy Lovesoundcloud.com/vexento/vexento-trippy-loveyoutube.com/watch?v=qF9WM_aQF2wMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: https://Patreon.com/MakerinTraining
Week 4 | Day 27 of 30 | I Failed . . . Twice! Maker In Training 2017-12-29 | My Patreon Page: patreon.com/MakerinTrainingGuys thank you for the support!!You can view the entire 30 Days of Videos Playlist Here:youtube.com/watch?v=DICV5ZaPXtA&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Restoring a Paint Sprayer Air Compressor | Bringing a DeVilbiss Tuffy NCE-501 Totally Back to Life Maker In Training 2017-12-29 | I took an old DeVilbiss Tuffy paint spray compressor model NCE-501 with a 1/3 Hp GE Motor and restored it.The Process:I started by completely tearing down the compressor assembly to take inventory of all the parts that needed replaced. To my surprise, the only things that needed replaced were a grommet and the rubber feet. Even the diaphragm looked usable. I then scrubbed all the dirt and grim off all the parts. I noticed most of the old paint came off so I decided to completely remove the old paint with sand paper. I also used a drill mounted brush to help speed things up. I then painted all the parts trying to keep true to the original colors. I think a different orange would have been better, but hind sight. . . Once all the parts were painted, I reassembled everything. I had to use stoppers for the feet since I could not find any rubber feet that matched. I drilled a counter bore and then a small hole all the way through. I used some longer 1/4 20 screws to replace the shorter ones from the old rubber feet. I think the added height from the taller rubber is a benefit. I made sure everything was tight. I finished it off by cleaning up the wiring and adding a switch cover for safety. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingSafety Notes:Please make sure the piece you are working on is unplugged. Don't get shocked!! I doesn't feel good. . . trust me.Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comSong used - Crusin' soundcloud.com/vexento/vexento-cruisinyoutube.com/watch?v=5wLwG15Xq0kMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Strike 2 | Baby Its Cold Outside! Maker In Training 2017-12-28 | Well. . . That’s twice in a row now! The cold is terrible. . . I have an unheated garage. My batteries are dying so fast I can barely keep them charge fast enough. (I have two on a rotation) Paint is taking forever to dry. . . My house smells like a paint booth. Ok, Ok enough with the excuses. I failed once again.I hope you guys understand. Thanks for the support!You can view the entire 30 Days of Videos Playlist Here:youtube.com/watch?v=DICV5ZaPXtA&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
I FAILED. . . Maker In Training 2017-12-26 | Just a quick update. Sorry guys it just was too much with Christmas and everything else I had to work on. I hope you guys understand. Thanks for the support!You can view the entire 30 Days of Videos Playlist Here:youtube.com/watch?v=DICV5ZaPXtA&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Christmas Greetings | Announcing the winner of the Giveaway! Maker In Training 2017-12-25 | Merry Christmas!!!! Now get off your electronic devices! If you haven't seen the Chainmail Ornament video yet, Check it out!youtube.com/watch?v=MaOeosnk3vU&index=3&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwYou can view the entire 30 Days of Videos Playlist Here:youtube.com/watch?v=DICV5ZaPXtA&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Wire Wrapped Obsidian Pendant | Making a Silver Wire Jewelry Piece with a Hardened Lava Charm Maker In Training 2017-12-25 | We made a pendant from obsidian wrapped in silver plated wire. Obsidian is solidified volcanic glass.The Process:We started by chipping away at the obsidian using flint knapping techniques. Once we got a clean shape to use for the main piece, we the knapped a small heart into shape with some of the leftovers. We then took the wire and wrapped it around the piece making sure to wrap around all the sharp edges. We added a loop to attach the two pieces together and a loop for the chain. We opted to go with a pre-made black chain to compliment the obsidian. The pendant was hung on the chain to complete the necklace. We have provided links to some of the materials on Amazon below, as well as the pliers I use.If you enjoyed the video please give it a like and let us know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe materials:- Artistic Wire 26-Gauge Tarnish Resistant Silver Wirehttp://amzn.to/2BwiAas (Affiliate)- Cousin Precision Comfort 3-in-1 Plier for Jewelry Makinghttp://amzn.to/2j9ifU8 (Affiliate)My cousin made this as a gift, here is a link to his gaming channel:youtube.com/user/ZealousPolymathSafety Notes:Flint knapping is dangerous since you are chipping small pieces of glass away. If you do this, please wear eye and hand protection!Music by Ukiyohttp://soundcloud.com/ukiyoauhttp://www.facebook.com/ukiyoauSong:Let me Downsoundcloud.com/ukiyoau/letmedownMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Free Form Copper Sculpture | Making an Art Piece From Electrical Wire Maker In Training 2017-12-24 | My son and I made a wire art piece by free forming copper from standard electrical wire.The Process:We started by removing the insulation form the wire and cutting it into several short pieces. We then formed the wire to shapes that looked pleasing to us. We then cut some plywood into small squares and painted them black. When the bases were dry, we drilled small holes to accept the wire diameter that we had. We then pressed the wire into the bases and added small rubber bumper to the bottom. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you would like to support what I do, Check out my Patreon: patreon.com/MakerinTrainingIf you are interested in more, please consider subscribing! youtube.com/makerintrainingSafety Notes:We made sure to clean up the ends of the wire so as to not have sharp edges. I have a feeling a sharp pointy tip would not make for a pleasent forming experience.Music by Vexento:Floating with Yousoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comsoundcloud.com/vexento/vexento-floating-with-youyoutube.com/watch?v=aNSn3RW0xmIMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Week 3 | Day 22 of 30 | Giving Away the Chainmail Ornament | Giveaway is Over. . . Maker In Training 2017-12-23 | The Giveaway is over. . . Here is the winner:gleam.io/W08an/chainmail-ornament-giveaway If you haven't seen the Chainmail Ornament video yet, Check it out!youtube.com/watch?v=MaOeosnk3vU&index=3&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwYou can view the entire 30 Days of Videos Playlist Here:youtube.com/watch?v=DICV5ZaPXtA&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMusic by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comsoundcloud.com/vexento/space-ride-1youtube.com/watch?v=85wgOCDX1doMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingFor this giveaway, all rules and entries are managed by Gleam. Here is the link: gleam.io/W08an/chainmail-ornament-giveawayThe Gleam widget will be selecting one winner at random, and the winner will be contacted via the email address you provide in the widget. (We have a strict privacy policy listed in the widget. Absolutely no personal information will be kept, other than to only notify the winner.) The winner has 72 hours to claim the prize, or we will redraw a new winner.For a full list of giveaway rules and requirements, please click the “Terms & Conditions” in the widget link above, before placing your entry.This giveaway is open internationally, and all entrants must be 13 years of age (or older) to participate, or have a parent enter for you, and we will be verifying this. The contest ends on Sunday Night, December 24th 2017, 11:59:59 PM Pacific Time (US & Canada) and the winner will be announced the day after the contest ends (December 25th), via YouTube and in the widget link above, so be sure to subscribe and check back!_FTC Disclaimer: This is not a sponsored video, and YouTube is not a sponsor nor party to the giveaway on our website. All giveaway items were made by us personally.This giveaway is ran in accordance to the YouTube Community Guidelines and YouTube Terms of Service. youtube.com/yt/policyandsafety/communityguidelines.htmlyoutube.com/static?template=termsAny entries not following the YouTube Community Guidelines will be disqualified. Personal data from the giveaway will NOT be used or shared in any way, shape or form.
Restoring a Pampered Chef Mini Serving Spatula |Turn a Kitchen Utensil Into a Cast Iron Cooking Tool Maker In Training 2017-12-22 | I restored the handle on an old Pampered Chef Mini Serving Spatula. I use this in the kitchen all the time with my cast iron cookware. The Process:I started by removing all the old pieces from the previous handle. I then found some pre-milled hardwood that was just the right width. I then cut a strip about one inch wide and about 6 inches long. I marked the depth that the tang would fit into the handle and cut a thin notch using a jigsaw. I then marked and drilled holes for retaining pins. I used old nails as the pins and cut them down to fit. I then used some five minute epoxy to secure everything together. Once the epoxy was dry, I sanded everything to a 180 grit. I finished it all off with butchers block oil. I have included links below to several of the items I used in this video. If you don't feel like doing this, you could always by a new one. . .Pampered Chef Mini-Serving Spatula #2622http://amzn.to/2BMvOAN (Affiliate)If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing and maybe even supporting me on Patreon! youtube.com/makerintrainingpatreon.com/MakerinTrainingEpoxy and butcher's block finish I used:Devcon 20945 S-209 High Strength 5-Minute® Fast Drying Epoxyhttp://amzn.to/2C6rsnk (Affiliate)Howard BBC012 Butcher Block Conditionerhttp://amzn.to/2p8dRKE (Affiliate)Safety Notes:Make sure the work is clamped down when using a jigsaw. If not, things jump aroud. . a lot!Music by VexentoOperation Funk (Inspiration)soundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comsoundcloud.com/vexento/vexento-operation-funkyoutube.com/watch?v=BFqzMVdJ4bYMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Making a Copper Dreamcatcher | Bringing the Mythical Tlanowa Bird to life Maker In Training 2017-12-21 | I made a dreamcatcher using copper. Tlanowa bird - A giant bird with copper feathers common to the mythology of many Southeastern tribes of North America.The Process:I started by making a hoop using some steel wire I had. I opted not to purchase a hoop since I had the steel wire, but I have provided a link to some hoops below. Once the hoop was made, I wrapped the entire hoop in a thin leather rope. Once wrapped I used some electrical wire that I had previously processed. I used the copper to weave the dream catcher. The method I used is detailed in a video by Emilie Lefler. Once Weaved, I cut out feathers from some thin copper tin. I attached the feathers using the same copper wire as before. I finished it all off with a loop above to hang it.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe Metal Hoop and Leather:Zinc Metal Rings, 5-Inch, 4-Packhttp://amzn.to/2BQ4Mez (Affiliate)3mm Flat Genuine Leather Cord Dark Brownhttp://amzn.to/2z7XRYB (Affiliate)Dreamcatcher Tutorial:youtube.com/watch?v=Vmtkc7FOWLwSafety Notes:Cutting thin metal with scissors can leave sharp edges. Sharp Edges are. . . well . . . Sharp, be careful.Music by VexentoBeautiful Dreamsoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comsoundcloud.com/vexento/beautiful-dreamyoutube.com/watch?v=jNUjLXpy7OAMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Making a Chainmail Ornament | A Project Using Recycled Copper Maker In Training 2017-12-20 | Making a Chainmail Ornament | A Project Using Recycled CopperI made an ornament from recycled copper. I used chain mail as the design.The Process:I started by stripping the wire using a precision blade. I then looped each type of wire around different size mandrels to give me the various diameters. I then used cutters to make jump rings from the coils. I used two pairs of pliers to assemble the ornament using an image as a pattern.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingI'm on Patreon!patreon.com/MakerinTrainingSafety Notes:Precision blades are sharp, please be careful when trying to cut things that are thick. Its better to get the right tool then to force things.Music:Joy to the World (Instrumental Jazz) Deck the Halls (Instrumental Jazz)Music by E's Jammy Jamsyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Faux Metal Animal Bookends | Making Fake Copper Giraffe Bookends From a Baby Toy Maker In Training 2017-12-19 | I made a set of faux copper giraffe bookends to go in my son's room. I used a toy animal to make it.The Process:I started by purchasing a toy giraffe from the store. I decided that cutting up one of my son's toys was probably a bad idea. . . I then used some scrap plywood and cut it into 4 equal (Sort of) sizes. I used the square pieces to make two ninety degree sections and glued them together. I then cut the toy in half using a saw. I tried cutting it with a knife, but the plastic was too think to be safely cut this way. Once the wood glue was dry, I used epoxy (Link below) to secure the toy pieces to the bases. I painted everything black as a base coat. I then used some metallic paint and dry-brushed it on the high points and edges to create the aged cast copper look. I added some non-slip bumpers to the bottom and called it a day. : )If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingEpoxy and metal paint I used:Devcon 20945 S-209 High Strength 5-Minute® Fast Drying Epoxyhttp://amzn.to/2C6rsnk (Affiliate)FolkArt Metallic Acrylic Paint, Antique Copperhttp://amzn.to/2BbNhFZ (Affiliate)FolkArt Metallic Acrylic Paint, Solid Bronze (Not exactly what I used, but its close)http://amzn.to/2Bb5wvb (Affiliate)Safety Notes:Precision blades are sharp, please be careful when trying to cut things that are thick. Its better to get the right tool then to force things.Music:Ivory by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comsoundcloud.com/vexento/vexento-ivoryyoutube.com/watch?v=kTtru6dwYo0My Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Braided Leather Cuff | Making a Mystery Braid Leather Bracelet From Reclaimed Materials Maker In Training 2017-12-18 | I made a leather cuff bracelet using reclaimed leather. I weaved the mystery braid for this one!The Process:This project started with a leather purse my sister had as a kid. I decided to reclaim the purse and make something that she could wear out of it. I first took the purse and removed the stitches. I decided to go with the lower part of the purse since it had the least amount of wear. Once I had the leather piece, I used some thick paper and an iron to smooth out the creases and warping in the leather. I then used a sharp knife and cut the piece to size adding rounded ends and holes for the hardware. I then cut two parallel lines down the center creating three equal strands. I weaved the strands using a method I found online. I included a link to the video below. I finished it off with crimp style snaps which you can purchase on Amazon (Link below as well).If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe Snap Kit I used:Dritz Heavy Duty Snaps Size 24-5/8"-7 Ct 7, Antique Brasshttp://amzn.to/2kEAXTr (Affiliate)Leather Mystery Braid Cuff Tutorial:youtube.com/watch?v=bCEC4d-KaQUSafety Notes:Precision blades are sharp, please be careful if you attempt this project. Keep you fingers away from the blade.(Unlike me)Music by Joe BagaleChicagoyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Forged Wire Bookmark | Making a Steel Bookmark from a Wire Hanger Maker In Training 2017-12-16 | I made a forged steel bookmark using a wire hanger and some metal accent pieces. This would make and excellent gift.The Process:I started by getting a wire hanger. I drew a design to scale using a permanent marker as a template I could follow. I then used a propane torch and some pliers to heat the wire and bend it into shape. Once I got it close, I trimmed the wire down to size. I then reapplied heat and hammered the wire to give it its final look. I used some of the leftover wire to make some jump rings. Using the Jump rings, I finished the bookmark off by attaching some oriental metal accents to the loops of the wire.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingSafety Notes:Propane is fire. . . fire should be respected for its ability to heat things up and burn!!Music by Huma-HumaCrimson Flyyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Half Way There | Day 15 of 30 Maker In Training 2017-12-15 | The random Amazon Affiliate Link example:Devcon 20945 S-209 High Strength 5-Minute® Fast Drying Epoxyhttp://amzn.to/2C6rsnk (Affiliate)I go over the last 15 days worth of videos and announce me joining the Amazon Associates Program.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingI have a Patreon!patreon.com/MakerinTrainingFull Playlist:youtube.com/watch?v=i9d_ES4ZRqQ&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwWeek 2:Making Deadpool Wall Art | Making a Design From Brass Casings youtu.be/kU__1W6NGJMMaking a Christmas Star | Using Scrap Tin to Make a Metal Five Pointed Texas Staryoutu.be/Fe3KZsnn11oKey Hook | Using Old Keys to make a Key Holder youtu.be/67ur7R6TshsViking Weave Copper Bracelet | Making Jewelry with Scrap Wireyoutu.be/QXxTKJrI_BIMandalorian Skull Wall Art | Making a Star Wars Universe Piece from Scrap Metalyoutu.be/95D6vNfq2M4Wild Grape Vine Christmas Ball Ornament | DIY Project from Raw Materialyoutu.be/KtkquyIIVfsWeek 1:Week 1 Wrap Up | I'm now on Patreon!youtu.be/i9d_ES4ZRqQMaking a Patch From a Baby Sweater | Saving a Childhood Memory using Embroideryyoutu.be/BUeFPaArYRIStars and Planets | SPRAY PAINT ART feat ZealousPolymathyoutu.be/eviCJRmkHakMaking the Die Hard Vent Ornament | A Project Using Real Ductwork youtu.be/LnZkounVEEEMaking a Puzzle Frame from Pallet Wood | Framing a Memory From our Honeymoon youtu.be/docceir2b0UHandmade Chainmail Ring | An Easy Gift or Christmas Presentyoutu.be/oSn4FFylZYQBuilding the LEGO StarWars Set 75525 | A project with my Nephewyoutu.be/uQI7YCLXbvE Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comSpecific Song: Eyes Closedsoundcloud.com/vexento/vexento-eyes-closedyoutube.com/watch?v=JkeG3DoLpyAMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Turning Brass Casings into this!? Maker In Training 2017-12-14 | I made a Deadpool art piece using brass bullet casings. Taking a wall brake to a whole new level. The Process:I started by getting a good low detail image of the Deadpool head. I then transferred the design to a large piece of plywood. I cut it out using a jigsaw and a fine tooth blade to make sure it didn't chip out. I then used some two part epoxy to attach the bullet casings (Link below). I got my brass shells from an uncle, but you could always contact a local shooting range and get some for cheap or free! Once I finished attaching all the brass and let the epoxy dry, I painted a base coat of black. The black base coat gives depth to the other colors. Once the black was done, I used a cardboard stencil to paint the eyes white. I then finished it all up with a deep red. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingEpoxy I used:Devcon 20945 S-209 High Strength 5-Minute® Fast Drying Epoxyhttp://amzn.to/2C6rsnk (Affiliate)Safety Notes:Be careful when using a jig saw. If the piece you are cutting is not secure, it could come out of your hands and hurt you or someone else.Music by Vibe TracksBreak You Inyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Making a Christmas Star | Using Scrap Tin to Make a Metal Five Pointed Texas Star Maker In Training 2017-12-13 | I made a black Christmas star for our tree this year. This same process can be used to make any kind of tin star, such as a Texas five pointed star, using thin scrap metal.The Process:I started by finding a star template on the internet. I printed it over-sized since the bending tends to squeeze the size down a bit. I then found some scrap tin I had laying around. Mine comes from a stove pipe that was cut up for another project. (link below) I traced two stars from the template and added tabs to one of them. I then bent the stars into shape making sure to keep with the lines. I used a sharp corner, in my case a jointed piece of wood, to make sure my bend lines were sharp. I then assembled the two stars into one. In my case solder worked to join the edges together to make a more sturdy assembly. I added a cone to the bottom using some of the leftover tin to make it. I finished it all up with some black paint that I then scuffed up a bit to give it a more rustic look.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingOther tin Projects:Making the Die Hard Vent Ornament | A Project Using Real Ductwork youtube.com/watch?v=LnZkounVEEE&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuww&index=8Mandalorian Skull Wall Art | Making a Star Wars Universe Piece from Scrap Metal youtube.com/watch?v=95D6vNfq2M4&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuww&index=3Safety Notes:Be careful when cutting and working with sheet metal/tin. The edges get very sharp and can easily cut you. You should always wear gloves when working with thin metal like this. I did not. . . Don't follow my bad example.Music by Vexentosoundcloud.com/vexentoyoutube.com/user/Vexentohttp://vexentomusic.comsoundcloud.com/vexento/verve-2Specific Song:Verve youtube.com/watch?v=c6TTps_yYYkMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTraining
Key Hook | Using Old Keys to make a Key Holder Maker In Training 2017-12-12 | I made a key holder by turning old keys into hooks.The Process:I started by using our old key holder do get an idea of the size I needed. I then used some old pallet wood and broke it to give it a rustic look. I then stained it black to further emphasis the look. Using a propane torch I got the keys hot and bent them over a round piece of steel. I doing this I had to heat and bend incrementally so as not to break the keys. (I broke a few and had to make more) Once they were shaped, I pre-drilled the holes for some small brass screws I had. Finally, I attached the keys making sure to stagger them a bit.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingSafety Notes:Be careful when heating metal red hot. I dropped the keys several times and almost burned my self. Don't do this.Music:Talky Beat by Twin Musicomyoutube.com/audiolibrary/musicTalky Beat by Twin Musicom is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/by/4.0)Source: http://www.twinmusicom.org/song/265/talky-beatArtist: http://www.twinmusicom.orgMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTraining
Viking Weave Copper Bracelet | Making Jewelry with Scrap Wire Maker In Training 2017-12-12 | I made a copper bracelet using a Vicking weave pattern with old junk wire. This would make and excelent gift.The Process:I started by finding some suitable scrap wire and stripping it to the bare copper. I then created a flower shape to start the weave. I followed the instructions from (Link below). I notice very quickly that the wire I had picked was too thin and kept breaking on me. I decided to try again with thicker wire. I used six loops and a single weave to complete the first step. I then used some scrap wood and drilled subsequent smaller holes in the wood to create a step board. I drew the weave through the step board starting with the bigger whole and working my way down to the smallest size. I then used some thinker gauge wire to create the ends. If you want to do this project but don't have scrap wire laying around, I provided links to some you can get on Amazon below, as well as the pliers I use.If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingThe Wire and Pliers:- Artistic Wire 26-Gauge Bare Copper Wirehttp://amzn.to/2B75nYg (Affiliate)- Cousin Precision Comfort 3-in-1 Plier for Jewelry Makinghttp://amzn.to/2j9ifU8 (Affiliate)Safety Notes:I did not use wire cutters or stripper to get the copper. Using the wrong tool is dangerous, don't do this!Music by Joakim Karudyoutube.com/channel/UCVBUm9ccjHy0utvlChyrPHASong:Fresh Startsoundcloud.com/joakimkarud/fresh-startMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Mandalorian Skull Wall Art | Making a Star Wars Universe Piece from Scrap Metal Maker In Training 2017-12-11 | I made a nice sheet metal version of the Mandalorian skull symbol from the Star Wars universe. The Process:I started by searching for a vector version of the design on the internet. Once I found one that was suitable, I used software to resize and fit the design on an eight and a half by eleven sheet of paper. I then took a suitably sized piece of sheet metal and made sure it was flat. I cut out the design and used it as a stencil by attaching it to the metal using spray adhesive and painting over everything with a dark colored paint. After pealing off the paper stencil I was left with unpainted areas that outlined the design. I used a rotary tool with various bits and a bench grinder to remove all the black painted sections of the material. I then took some old nails and bent and cut them into shape to create some small hangers for the design. I used some thin plywood as a backer making sure to keep it about a half an inch away. (I used a second print out of the design to help me with this). After painting the backer a black color, I attached the metal pieces with both fast acting glue and some five minute epoxy. the fast acting glue allows the pieces to be attached and hold while the epoxy is for long term stability. I secured the wall art to the wall using some command strips. (link below)If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintraining*Links to the command strips(Affiliate)Command Picture & Frame Hanging Stripshttp://amzn.to/2jpBZ9uSafety Notes:Sheet metal can be sharp. I did not wear gloves in the video. Please wear gloves when working with this material. Music by Silent PartnerSong: Stadium Jobyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Wild Grape Vine Christmas Ball Ornament | DIY Project from Raw Material Maker In Training 2017-12-10 | I made a DIY Christmas ball ornament using wild grape vines a the raw material.The Process:I stared by collecting some wild grape vines from behind the house. Since winter had already hit, the vines were a little stiff and dry. I made them more pliable by soaking them in hot water for about fifteen minutes. Once soaked, I coiled 3 short pieces of vine into identical size coils using some thin aluminum wire to secure them. I then fit the three loops together to form the framework for the ball. Once the framework was done, all that was left to do was add more vine to the existing structure. I also added the curly bits of vine to the center of the ball for added visual appeal. The last step was to make the hook from some of the same wire. I think a red ribbon would look better, but I didn't have any at the time.If you do not have access to wild grape vines but want to make this yourself, I included some links below to grape vines you can purchase. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintraining*Links to the grape vine and wire(Affiliate)15 feet of Twistable and Lightweight Grapevine Twig Garland for Holiday and Home Decorhttp://amzn.to/2C1VVUoAluminum Craft Wire 18 Gaugehttp://amzn.to/2B4H39XSafety Notes:The wire is small and it is sometimes hard to get a hold of with the pliers, causing them to slip. Please be careful not to pinch yourself if you attempt to do this project. Music by E's Jammy JamsSongs: Up on the Housetop (Instrumental)We Wish You a Merry Christmas (Instrumental)youtube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
Week 1 Wrap Up | Im now on Patreon! Maker In Training 2017-12-08 | I go over this last weeks videos and announce my Patreon Page!If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintrainingI have a Patreon!patreon.com/MakerinTrainingFull Playlist:youtube.com/watch?v=i9d_ES4ZRqQ&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwBuilding the LEGO StarWars Set 75525 | A project with my Nephewyoutube.com/watch?v=uQI7YCLXbvE&index=8&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwHandmade Chainmail Ring | An Easy Gift or Christmas Present youtube.com/watch?v=oSn4FFylZYQ&index=6&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMaking a Puzzle Frame from Pallet Wood | Framing a Memory From our Honeymoon youtube.com/watch?v=docceir2b0U&index=5&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMaking the Die Hard Vent Ornament | A Project Using Real Ductwork youtube.com/watch?v=LnZkounVEEE&index=4&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwStars and Planets | SPRAY PAINT ART feat ZealousPolymath youtube.com/watch?v=eviCJRmkHak&index=3&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuwwMaking a Patch From a Baby Sweater | Saving a Childhood Memory using Embroidery youtube.com/watch?v=BUeFPaArYRI&list=PL19tiSkeb1YckCuTesADEcXb2NusuBuww&index=2Music:YouTube Audio LibraryCrimson Fly by Huma-HumaPayday by Jason Farnhamyoutube.com/audiolibrary/musicMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingPatreon: patreon.com/MakerinTraining
Making a Patch From a Baby Sweater | Saving a Childhood Memory using Embroidery Maker In Training 2017-12-07 | If you want to skip straight to the build: youtu.be/BUeFPaArYRI?t=63I gave new life to a sweater I had when I was a Baby by turning it into a patch.The Process:I stared by cutting the design away from the shirt. Then I cut out some Heat Bond* paper to match making sure it covered the entire design with at least an extra 1/8th of an inch border without out extending beyond the fabric. I then used an iron to seal the adhesive to the back of the piece. Using a pair of scissors I cut 1/8th of an inch away from the design. I then pealed the backing off the Heat Bond*. I realized later it would have been better to leave it on. I used some embroidery thread to go around the entire patch to clean up the edge. Finally, I cut out some Velcro* pieces to cover the entire back and ironed them on using the Heat Bond as the main adhesive. The Velcro* had a strong adhesive but I wanted to make sure it didn't come off. If you enjoyed the video please give it a like and let me know your thoughts in the comments below. If you are interested in more, please consider subscribing! youtube.com/makerintraining*Links to the Products I used (Affiliate)Thermoweb Heat'n Bond Ultra Hold Iron-On Adhesive http://amzn.to/2AC90DwVELCRO Brand - Industrial Strength - 2" x 4" Stripshttp://amzn.to/2j1Zi8XSafety Notes:Always move the iron around and don't leave it in one place for too long. Music by VexentoSymptomSong: youtube.com/watch?v=eMzYGy-ECMQChannel: youtube.com/channel/UCYZ9rknEmE4R1J_HBJ2yBlQMy Social Links:Youtube: youtube.com/MakerinTrainingInstagram: instagram.com/MakerinTrainingTwitter: twitter.com/MakerInTrainingAffiliate Statement:We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. This helps us pay for materials and such for our builds.
