That RV Tech
World 1st look at New rv company’s first model • Boundless Recreation Debut
updated
Had a client call me out for issues with a Victron system installed by a “solar company” out of Colorado. I stopped by for a quick diagnostic… and within about 30 seconds I knew this one was going to be a mess.
The system was throwing constant low-voltage and overload faults. Took one look and saw a #2 cable running about 15 feet from the battery to the inverter — no disconnect, no circuit protection. That same undersized cable was feeding all the DC loads in the coach, and there was another #2 cable feeding a 3000W inverter.
Just for fun, I ran a voltage drop test — nearly a 4V drop on a full battery just running a small hot plate. Before I could even finish testing, the BMS, VE.Bus, inverter — all started screaming and shutting down like the power bill didn’t get paid.
At that point it was obvious: the main cabling had to be corrected before anything else. Came back, installed properly sized cables, and started digging deeper.
It didn’t get better.
Incorrect lugs, undersized wiring, missing or wrong circuit protection all over the place. The 12V grounding was… honestly one of the worst I’ve seen. And yes — jumper cables being used for solar wiring.
Then I got a better look at the battery and had to break it to the customer: it was never designed to support a 3000W inverter. Not even close.
I could go on all day about everything wrong with this install.
We’re going to get it fixed the right way — and no, it’s not going to cost her $20,000 to undo someone else’s mistakes.
Point is — do your homework before hiring a “solar company.”
What I look for before recommending anyone:
* Real reputation (not just cherry-picked reviews)
* Multiple review sources
* Proper licensing and insurance
* Actual, verifiable experience
* Honest, transparent work (check their social media — it tells a lot)
A wrapped truck and a logo on a shirt doesn’t mean they know what they’re doing.
Honestly on the big installs, I send them to the pros myself. Some jobs are just better suited for the people who specialize in that specific area. I like a good puzzle so I’ll spend my time diagnosing other people’s installs 😂
And to be clear, these issues have nothing to do with victron, just the installers.
#Rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
“Every time I turn my furnace on, the AC comes on too”
or
“My AC fan won’t shut off when I’m using the furnace”
And I’m here to tell you… most of the time, nothing is wrong.
That’s actually a feature.
Your furnace and air conditioner are tied into the same thermostat, and a lot of times they’re even sharing the same control logic. So when you turn the furnace on, the thermostat can also tell the AC fan to run.
Not the AC itself… just the fan.
You’re not cooling anything. The compressor isn’t running. It’s just moving air.
⸻
Here’s why it does that:
Heat rises. All that warm air from your furnace ends up sitting at the ceiling. When the AC fan runs, it pulls that warm air and pushes it through the ductwork to evenly distribute heat throughout the RV.
So instead of hot ceilings and cold floors, you get a more balanced temperature.
⸻
Now, if you don’t like it, you can turn it off.
On your thermostat you’ll usually see:
• High
• Low
• Auto
• Off
If you don’t want the AC fan running with the furnace, set the fan to Auto or Off depending on your thermostat.
⸻
Side note… if you’ve never tried it, give it a shot next time it’s cold.
Those AC fans are actually really good at moving air, and it can make your RV feel a lot more evenly heated.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
Most of the time they cause more problems than they solve. They can put stress in the wrong spots, tweak things out of alignment, and turn a good slide into a bad one.
But every now and then I run into an RV like this…
And even my brain goes, “alright… maybe this one needs a little help” 😂
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
If not, there’s a good chance you’ve run into one and didn’t even realize it.
It’s basically a self-resetting 12 volt breaker. Instead of blowing like a fuse, it trips when there’s a problem, cools off for a second, then turns itself back on.
Sounds like a good idea… until you’re trying to figure out why something isn’t working.
Now you’ve got power, then no power, then power again… over and over. You’ll hear clicking, buzzing, things trying to run but not quite getting there. It can look like a bad motor or a bad switch when really the breaker is just doing its job.
They’re usually on higher draw stuff like slide rooms, leveling systems, landing gear, things like that.
The tricky part is they don’t fail in an obvious way. They just keep cycling, and if you don’t know they’re there, they can send you in the wrong direction real quick.
If you’ve got something acting weird, turning on and off, or not staying powered, don’t overlook one of these. It might not be the problem, it might be pointing you to it.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
If you swap it out, make sure the new one is doing everything the original was doing.
A lot of the detectors you’ll find at the hardware store are great at detecting carbon monoxide. In some cases, they’re even better than what came in your RV.
But here’s what people miss…
Your RV detector is usually doing two jobs:
• Carbon monoxide detection
• Propane (LP gas) detection
Most residential units do not detect propane.
And propane leaks absolutely happen in RVs. When they do, you’ve got a small enclosed space, plenty of ignition sources, and not a lot of room for error.
That’s a dangerous combination.
So if you upgrade or replace your detector, make sure you’re not losing that propane detection in the process.
Bottom line, you need:
• A carbon monoxide detector
• A propane (LP) detector
Whether that’s one combo unit or two separate devices, just make sure both are covered.
This is one of those things you don’t realize matters… until it really matters.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
That’s the problem.
“Budget” shouldn’t mean rushed, overlooked, or thrown together—especially in the areas that actually matter.
I’ll say it again…
If manufacturers stopped trying to load these units up with all the “wow factor” stuff, they could still build a solid, reliable RV at a budget price.
Because let’s be honest—
You don’t need:
• Two fireplaces
• Three refrigerators
• Fancy finishes everywhere
…if it means corners are being cut on:
• Electrical
• Plumbing
• Overall craftsmanship
I’d take simple and built right over flashy and falling apart any day.
If you were buying a budget friendly RV - would you rather have fancy stuff, or a quality build?
#Rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
Everyone always asks “what’s the strongest sealant?” but that’s not always what you want on an RV.
One of the things I’m testing is adhesion, and there’s a point where too much becomes a problem.
RVs flex, twist, and live on the road. Sealants are going to age, and at some point they will need to be replaced. That’s just the reality of it.
Now imagine using something that bonds like epoxy. Sounds great… until you actually have to remove it.
Need to replace a water heater?
Swap out a piece of trim?
Do work on a slide room?
Now that “super strong” sealant turns a 5 minute job into an absolute nightmare.
If sealant was truly permanent, RV techs wouldn’t exist.
You want something that sticks well, seals properly, and holds up… but can still be serviced when the time comes.
Because on an RV, everything eventually gets worked on.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
The issue isn’t really the battery. It’s how people install them.
You can’t just pull out a lead acid battery, drop a lithium in its place, and call it good. That’s where things start going wrong.
Most of the problems you hear about aren’t lithium batteries just randomly failing. It’s things like the wrong charger still in the RV, wiring that’s too small, no proper fusing, or components that were never designed to work with lithium in the first place. Basically a half-done setup.
The batteries themselves, especially LiFePO4, are actually very stable. They’re not the scary part. But they still need the right setup around them to work properly.
If your RV is still set up for lead acid, it might not charge the battery correctly, it might push the wrong voltage, or it might not protect anything if something goes wrong.
The biggest thing I see all the time is someone upgrades the battery and leaves everything else the same. Everything in that system works together, so when you change one part, the rest needs to match it.
Bottom line, lithium is a great upgrade. I run it and I recommend it. But it’s not plug and play.
Do it right and it’ll treat you well. Do it halfway and that’s when people start blaming lithium.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
Tell em Nick sent you!
#Rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
Can Azdel walls delaminate?
Short answer: yes — just not the way you’re used to seeing it.
If you’re not familiar, Azdel is a composite panel a lot of manufacturers are using instead of luan (wood) behind fiberglass walls. The big advantage is:
• It doesn’t absorb water like wood
• It won’t rot, swell, or turn to mush
• It doesn’t “peel apart” the same way a traditional laminated wall does when it gets wet
That’s why you hear people say Azdel “can’t delaminate.”
That’s not entirely true.
What actually fails isn’t the Azdel — it’s the glue.
RV walls are still a laminated structure:
• Fiberglass exterior
• Adhesive
• Azdel backing
• Framing
If that adhesive bond fails (from heat, poor lamination, or water intrusion), you can still get separation between layers.
So:
• Less prone to delam? Yes
• Immune to delam? Not even close
You just won’t see the same swollen, rotted look you get with wood-backed walls. It can be a little harder to spot, and sometimes shows up more as bubbling or soft spots.
Bottom line:
Azdel is an upgrade… but it’s not a force field. Water intrusion and bad lamination can still cause problems.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
In this video, I break down one of the most common issues I see with RV hydraulic leveling systems — that awful buzzing sound when you hit the button.
Most people assume something is broken.
Most of the time… it’s not.
⸻
What’s actually happening:
That buzzing noise is coming from your dual polarity solenoid on the hydraulic pump.
It’s basically a big electrical switch that tells the motor which direction to run. When it doesn’t get enough voltage, it rapidly engages and disengages — which is what creates that buzzing sound.
⸻
The real problem (most of the time):
👉 Voltage drop / voltage sag
This can be caused by:
• Low battery
• Bad battery (even if it “looks” charged)
• RV not plugged into shore power
• Weak 12V system overall
Quick takeaway:
If your leveling system is buzzing, start with your battery.
A healthy RV battery should hold voltage under load. If you hit the button and see a big voltage drop (like 12.5V → 10–11V), you’ve likely found your problem.
Pro tip:
Before leveling or running slides:
👉 Plug into shore power first
It helps support the battery and keeps voltage where it needs to be for high-demand systems like leveling jacks and slide motors.
⸻
Important disclaimer:
This won’t fix every situation. Solenoids can fail, and other components can go bad. But in a large number of cases, this buzzing issue comes down to voltage and battery condition.
⸻
Keywords (for search):
RV leveling system buzzing, Lippert leveling system problems, RV hydraulic jacks not working, RV leveling system troubleshooting, RV battery issues, RV voltage drop, RV solenoid buzzing, RV jack system not working, camper leveling problems, fifth wheel leveling system, travel trailer leveling issues, RV electrical troubleshooting
⸻
If you want more real-world RV diagnostics and no-BS explanations, hit subscribe.
But what about the stuff you keep for when things go wrong?
You’ve got your fire extinguisher, smoke detectors, LP/propane detectors… all the obvious “just in case” items.
But what about the thing that happens all the time in RVs…
Leaks.
In this video, I’m breaking down why you should treat water intrusion like an emergency — because I see it constantly. People in full panic mode during a storm, posting in Facebook groups while water is actively coming into their RV.
You wouldn’t do that with a fire… because you’re prepared.
So let’s fix that.
What this video covers:
• What to keep in your RV for emergency leak situations
• Why most sealants won’t help you in the moment
• A simple, cheap solution every RV owner should carry
The reality is most sealants require:
• Dry surfaces
• Prep work
• A nice sunny day
That’s great… until it’s raining and water is pouring in.
That’s where something like Lexel Clear Sealant comes in.
It sticks to wet surfaces, which makes it one of the few options that can actually help in an emergency situation.
They even make small squeeze tubes — no caulk gun needed — so you can just toss one in a drawer and forget about it until you need it.
Think of it like a “leak extinguisher.”
you can get it here - amzn.to/4c6Kei8
Quick disclaimer (because someone will say it):
This isn’t a permanent fix, and it’s not going to save you from every situation. If you’ve got a massive hole in your roof, this isn’t magic.
But for a lot of common RV leaks?
It can buy you time and prevent serious damage until you can fix it properly.
And honestly… ugly sealant is better than a rotted floor, wall, or roof.
⸻
Why this matters:
Water damage is one of the most expensive and common problems in RVs. Being prepared can be the difference between a quick fix and a major repair.
*links within this video may be afilliate links, which means I may earn commission at no extra cost to you.
In this video, I break down my real RV tool bag as a professional RV technician and show you the essential tools every RV owner should carry for maintenance, DIY repairs, and troubleshooting.
Most people think they need a massive tool kit… you don’t.
This bag right here handles about 80% of my RV service calls, and it’s more than enough for the average RV owner.
We’re going through the must-have RV tools, what you actually need, what you don’t, and how to avoid wasting money on tools you’ll barely use.
⸻
In this video:
• Best tools for RV maintenance and repairs
• Minimal RV tool kit setup
• Must-have RV hand tools
• RV electrical tools (multimeter, wire strippers, crimpers)
• Best screwdriver and drill options for RV use
• Budget vs pro tools (what’s worth it and what’s not)
• Common mistakes RV owners make with tools
⸻
Some of the key tools covered:
• Non-marring scraper (for sealant removal and roof work)
• Pry tools and trim removal tools
• Multi-bit screwdriver (square + Phillips are key)
• Pliers (needle nose, adjustable, cutters)
• Wire strippers and crimpers
• Small socket set (metric + SAE basics)
• Compact drill / driver (no, you don’t need an impact)
• Rechargeable electric screwdriver (budget-friendly option)
• Multimeter (arguably the most important tool in your RV)
• Outlet tester with voltage readout
• Inspection mirror, magnetic pickup tool, and more
⸻
Why this matters:
Having the right tools in your RV can help you:
• Fix common RV problems yourself
• Diagnose electrical issues faster
• Avoid unnecessary service calls
• Prevent damage from using the wrong tools
⸻
My take:
You don’t need Snap-On, Milwaukee, or high-end tools for basic RV work.
Most of this can be done with Harbor Freight, Amazon, or budget tools.
The goal isn’t to be a technician… it’s to be prepared.
⸻
Tools mentioned in this video:
Check out my Amazon storefront for links to everything shown (plus budget alternatives) at thatrvtech.com
⸻
Subscribe for more RV tech tips:
If you want more real-world RV advice, maintenance tips, and no-BS breakdowns from an RV tech, hit subscribe.
Most of you don’t need the biggest, baddest drill on the shelf. In fact, that’s how you end up stripping screws, wallowing out holes, and damaging your RV… all while spending money on something you’ll use a few times a year.
A drill/driver is one of the most overbought tools in the RV world.
You don’t need an impact driver.
All that does is:
• Tear up fasteners
• Overdrive screws into thin RV materials
• Make a bunch of unnecessary noise
For 90% of RV owners, a small rechargeable screwdriver is all you need.
Something you can:
• Toss in a drawer
• Grab quickly for quick fixes
• Use without destroying what you’re working on
I’ve got a Bosch/Dremel GO Cordless Screwdriver at home and honestly, I love it for this kind of work.
I also tested one of the Amazon versions made by SKIL, and it actually held up really well for something in a small, affordable package.
Bottom line:
If you’re doing basic RV maintenance, repairs, or adjustments, you don’t need pro-level power tools.
You need control.
you can find this little guy here: amzn.to/4t9p6On
full "tour" of the tools I carry every day will be up on YouTube shortly 👍🏻
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
disclosure: links within this post may be affiliate links, which means I may earn a small commission at no extra cost to you.
If you’ve ever dealt with an RV roof leak, window leak, or seam failure, you already know how important the right sealant is.
One of the biggest things I’m focusing on is flexibility (stretch).
RVs don’t sit still:
• They flex going down the road
• They twist when leveling
• They expand and contract with heat and cold
If your RV sealant can’t move with that, it’s going to crack, separate, and eventually leak. It’s not a matter of if — it’s when.
And here’s the part most people miss…
A lot of sealants feel flexible when they’re fresh, but as they age, they turn hard and brittle. That’s where failures start.
That’s why, in my opinion, flexibility is one of the most important factors when choosing the best RV sealant.
But I’m not stopping there. I’m putting these products through real testing for:
• Adhesion (what surfaces they actually stick to — fiberglass, aluminum, TPO, PVC, etc.)
• UV resistance (how they hold up in sun exposure over time)
• Ease of application (because some are a complete nightmare to work with)
• Longevity (cracking, shrinking, yellowing)
• Cost vs performance
• Availability (what you can actually get your hands on when you need it)
There’s a lot of marketing around “RV sealants”… but most RVs are built with standard materials. Not everything labeled “RV” is actually the best option.
If you’re trying to prevent RV water damage, roof leaks, or exterior seam failure, this is the stuff that actually matters.
I’ll be sharing real results as I go — what works, what doesn’t, and what’s just hype.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
This comes up all the time with RV appliances, and here’s the reality:
A lot of the time, if the repair cost is getting anywhere close to replacement… replacing just makes more sense.
Not always. But more often than people think.
Here’s why:
• You reset the clock
New unit = new warranty. That alone has real value, especially in RVs where stuff just doesn’t last like it should.
• You get a full set of spare parts
If you replace instead of repair, you now have your old unit sitting there.
Boards, fans, motors, sensors… all parts you will need eventually.
In this industry, having parts on hand is huge.
• You’re not dumping money into something that’s already failed once
Let’s be honest… it’s an RV.
If it failed once, there’s a good chance something else on that same unit isn’t far behind.
• For a little more money, you get a brand new unit
This is the big one.
If you’re spending $600–$800 to fix something, and a new unit is $1,000–$1,200…
You’re basically paying a little extra to eliminate risk.
Now, to be fair — repair still makes sense when:
• It’s a simple, low-cost fix
• The unit is newer
• Parts are cheap and easy
But once you start stacking labor + parts… you need to step back and actually do the math.
Because sometimes “fixing it” is just the more expensive decision long term.
Bottom line:
Don’t just default to repair because it feels cheaper.
Look at the total cost, the risk, and what you’re actually getting for your money.
Sometimes replacing it is the smarter play.
v appliance repair, rv appliance replacement, repair or replace rv, rv repair cost, rv maintenance tips, rv appliances explained, rv tech advice, rv refrigerator repair, rv water heater repair, rv furnace repair, rv ac repair, rv air conditioner replacement, rv troubleshooting, rv repair vs replace, rv ownership tips, travel trailer repair, fifth wheel repair, rv life tips, rv problems, rv upgrades, rv appliance failure, rv cost savings, rv diy repair, rv technician advice, when to replace appliances, rv service tips, rv inspection tips, rv ownership mistakes
⸻
I’m going to be straight with you, I’m generally not a fan. And it’s not because covers don’t sound good in theory… it’s because of what I’ve actually seen in the real world.
Let’s start with the cons, because there are quite a few.
First, moisture. This is the big one. A lot of covers claim to be “breathable,” but that doesn’t mean good airflow. In reality, I’ve seen covers trap moisture against the exterior, especially in climates with temperature swings. You get condensation forming underneath, and now that moisture just sits there. Over time, that can lead to staining, mold, and even contribute to seal deterioration.
Second, movement. Wind is not your friend here. Even a “properly secured” cover will move. Those straps and buckles? They don’t just sit still. I’ve seen them repeatedly smack against the sidewalls, front caps, windows, and gutters. Over time, that turns into scuffs, scratches, and sometimes worse. It’s basically slow, consistent abrasion.
Third, wear and tear on the RV itself. The cover might be softer than you think, but when it’s constantly shifting in the wind, it acts like sandpaper. Especially on corners, edges, and anything that sticks out. I’ve seen graphics get dulled and even worn down from this.
Fourth, false sense of security. A lot of people think “it’s covered, I’m good.” Meanwhile, small issues go unnoticed. Sealant cracks, water intrusion, roof damage… you don’t see it because it’s buried under a cover for months. Out of sight, out of mind.
Fifth, install and removal. Let’s be honest, most people hate dealing with them. They’re a pain to put on, a pain to take off, and if you’re not doing it right, you’re increasing the chances of damage during installation alone.
And lastly, airflow. RVs are not airtight, and they rely on some level of natural air exchange. A full cover can limit that, especially if it’s not designed well. That can contribute to stale air, trapped humidity, and interior moisture issues.
Now, to be fair, there are some pros.
Covers can help protect against UV exposure, which is a real thing. Sun will absolutely beat up your seals, plastics, and graphics over time. They can also keep off debris like leaves, sap, bird droppings, and snow buildup, which reduces how often you’re cleaning.
In certain situations, like long-term storage in harsh sun or under trees, a cover can make sense.
But here’s the key… if you’re going to use one, do it right.
Don’t cheap out. Get a quality cover that’s actually designed with ventilation in mind. Make sure it fits your RV properly, not some “close enough” universal size. Take your time securing it so it’s tight, balanced, and not flapping all over the place.
And even then, don’t just forget about it. Check on your RV. Pull the cover back periodically and inspect everything like you normally would.
At the end of the day, I’ve personally seen more headaches caused by covers than problems they actually solved. That doesn’t mean they’re useless… it just means they’re not the magic solution people think they are.
Like most things with RVs, it comes down to proper use, maintenance, and understanding the trade-offs.
#Rvtechnician #rv #rvliving #rvlife #rvlifestyle #rvtips #camper #camperlife #camperlifestyle #campertips #camperrepair #rvrepair #rvdiy #camperdiy
A lot of the fires you see online — phones, e-bikes, scooters — those are usually lithium-ion or lithium polymer batteries. They’re built to be small and powerful, but they’re not very forgiving.
What’s happening in those situations is something called thermal runaway. Basically, the battery starts heating itself faster than it can cool down, and once it starts, it keeps feeding itself.
But here’s the part nobody explains…
Most RVs are running LiFePO4 batteries. Completely different chemistry. Much more stable, much harder to overheat, and far less likely to go into thermal runaway.
That doesn’t mean they’re risk-free.
Almost every battery issue I’ve seen in the field comes down to something preventable:
• wrong charging setup
• loose or undersized wiring
• no proper fusing
• cheap, no-name batteries
• poor installs
That’s where the real danger is.
DIY isn’t the problem… DIY without understanding is. You can wire something up today and it “works,” but issues show up later when heat builds up or connections start to fail.
A properly installed lithium system is one of the safest setups you can run in an RV.
A bad install? That’s where things go sideways.
The battery isn’t the problem… the install is.
#Rvtechnician #rv #rvliving #rvlife #rvlifestyle #rvtips #camper #camperlife #camperlifestyle #campertips #camperrepair #rvrepair #rvdiy #camperdiy
We talked about black tank smells coming from bad venting, and your gray tank works the same way. There’s a vent stack that runs up through the wall and out the roof. If that’s blocked or damaged, you can get odors backing up.
But gray tanks have a couple other problem spots people miss.
First one is under your sink — that white piece you’ll sometimes see is a waterless P-trap. Instead of holding water like a normal P-trap, it uses a rubber flap to keep gases from coming back up.
Problem is… if that flap gets stuck open or debris gets in there, it’s basically an open path for tank smells to come right back through your sink.
This is why I still prefer a traditional P-trap. Water doesn’t fail the same way.
Now even if you do have a normal P-trap, there’s another one to check — an air admittance valve.
You’ll usually find it under the sink, on a small vertical pipe. It’s a little valve that lets air in so your system can drain properly.
If that fails, same deal — gray tank gases can come right back into the RV.
So if you’re chasing a smell:
• Check your roof vent
• Look for a waterless trap and make sure it’s clean and sealing
• And check that air admittance valve under the sink
A lot of times it’s one of those, not the tank itself.
Just one of those things that gets overlooked but can drive you nuts until you find it.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
No active leak anywhere… but the damage was definitely there.
Turns out the bathroom was basically being used as a steam room.
They were skipping the vent fan during showers because the steam helped with sinus issues. I get it — my sinuses suck too. But in an RV, that steam has nowhere to go.
And here’s the reality:
Steam = water.
That moisture will work its way into your ceiling, walls, insulation — everywhere. Once it cools, it condenses and just sits there. That’s how you end up with soft spots, staining, and eventually rot.
The vent fan isn’t just for smells — that’s the bonus. Its real job is moisture control.
If you’re taking hot showers in your RV without the fan running, you’re slowly creating your own “leak.”
Run the fan. Every time.
#Rvtechnician #rv #rvliving #rvlife #rvlifestyle #rvtips #camper #camperlife #camperlifestyle #campertips #camperrepair #rvrepair #rvdiy #camperdiy
A lot of people push it simply because they think it’s “made for RVs.” In my opinion, that doesn’t really mean much. RVs are built out of the same materials as everything else—fiberglass, aluminum, plastics—there’s no magic “RV-only” sealant.
Here’s been my experience with Proflex: it looks good at first, but over time it hardens, yellows, and starts to crack. And once it turns rock hard, removal becomes an absolute nightmare.
And that’s the part people don’t talk about—sealant is maintenance. It will need to be redone at some point. If it turns into concrete, you just made your future self miserable.
Now to be fair, it is marketed as flexible and crack-resistant , but real-world use doesn’t always match that. Plenty of users report it getting hard and losing flexibility over time .
If it truly stayed flexible forever, my opinion would be completely different. But it doesn’t… so for me, it’s not the move.
#Rvtechnician #rv #rvliving #rvlife #rvlifestyle #rvtips #camper #camperlife #camperlifestyle #campertips #camperrepair #rvrepair #rvdiy #camperdiy
When I was at the dealer, I used to laugh a little when these got “special ordered” under warranty. Customer waits weeks… parts show up… appointment gets scheduled… all for something you could’ve fixed the same day.
Most of these are just standard cam locks.
You can literally:
• Run to a hardware store
• Grab one for a few bucks
• Swap it out in about 5 minutes
No special tools, no waiting around.
And it’s not just repairs — this is also an easy upgrade.
You can:
• Ditch the common CH751 style keys
• Go to better lock cylinders
• Even upgrade to keypad locks if you want
Same sizes, same basic setup, way more options than people realize.
This is one of those things the industry makes seem more complicated than it is.
Simple fix. Cheap upgrade. Done.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
A manufacturer can say they build the “best” or “high-quality” products all day long… that doesn’t mean much.
Quality has to be seen.
It’s in the details. The little things most people walk right past.
When I see stuff like this, it tells me everything I need to know. And in my opinion, that’s low quality — regardless of where the unit falls on the price scale.
Entry level, mid range, “luxury”… doesn’t matter.
This shouldn’t be on any of them.
This is exactly why I always say — stop listening to the sales pitch and start looking closer.
anyone here install electrical systems? would you put your name on this???
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
#Rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
I’ve had plenty of people tell me, “a hose is a hose.”
It’s not.
Yeah, they all look the same. Same fittings, same size, all move water. But what they’re made of is completely different — and that’s what matters.
Garden hoses are made with cheaper materials. Let them sit in the sun, heat them up, and those materials start leaching into the water you’re drinking.
You might taste it… you might not. Especially if you’ve got filters on your RV. But just because you can’t taste it doesn’t mean it’s not there.
Drinking water hoses are made to limit that. Are they perfect? No. But they’re a whole lot better than pulling water through a standard garden hose.
And yeah — we all drank out of the hose growing up. I did too.
Doesn’t mean it was a good idea.
We’re already exposed to enough junk as it is. If there’s an easy way to reduce what you’re putting into your body, why wouldn’t you?
This is one of those accessories I actually consider a must-have. Same category as a surge protector or EMS — it’s not flashy, but it matters.
And like anything else, not all of them are created equal. This is one of those items where spending a few extra bucks actually makes a difference.
So call it a gimmick if you want… but I’m not running drinking water through a garden hose.
What do you think — gimmick or legit?
RV drinking water hose vs garden hose RV water hose safety RV accessories must have RV water system tips RV beginner tips RV life essentials travel trailer tips fifth wheel tips RV maintenance RV setup tips potable water hose RV microplastics in water safe RV living RV upgrades that matter
Thank you everyone for your support! You are why I do these giveaways. I’ve never paid for a view, follower, or like - I’d rather take that money and give back to you guys.
If you’re bummed about this one, stay tuned because I’ve got another one lined up already 😁.
#Rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
And honestly, it’s not your fault. This is one of those things that gets passed around wrong all the time.
Most people will tell you: hook up the hose, open the black tank valve, turn the water on, let it rinse. Yeah… that’ll rinse your hose out. It’s not really cleaning your tank.
What’s actually happening inside there is way less impressive than people think. There’s no pressure washer in your tank. It’s just a few weak little streams of water trickling around. That’s it.
So if you’re running it with the valve open, all you’re doing is letting water pass through. You’re not building any volume, and that’s what actually does the cleaning.
What works a lot better is simple: close the valve, fill the tank most of the way, then dump it. That big rush of water is what helps move everything out and clean the sides of the tank where stuff likes to hang up.
Only thing you gotta watch… don’t overfill it. If you do, it’s not coming out of the toilet — it’ll go up the vent stack and out the roof. Not a fun day.
Easiest ways to avoid that: use a flow meter on your hose, or just have someone keep an eye down the toilet while you’re filling. you can get a flow meter like this one: amzn.to/4cgfHyn
If you’re using any kind of tank cleaner, this is also the best time to use it. Fill the tank, let it sit, dump it later, then rinse it out again.
I know a lot of people think that flush system is doing way more than it is… but once you see it, it makes a lot more sense why tanks don’t get clean.
Just one of those things nobody really explains right.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
links within this post may be affiliate links, which means I may earn commissions with your purchase, at no extra cost to you.
Here’s the reality — RVs follow a good / better / best model, whether manufacturers admit it or not.
A “good” RV is built for:
• Weekend trips
• Occasional use
• Budget-conscious buyers
It’s not built for:
• Full-time living
• Heavy daily use
• Taking a beating year-round
So when someone buys an entry-level camper and then lives in it full-time with a family… yeah, things are going to wear out fast.
That doesn’t always mean it was built wrong.
It often means it’s being used outside of what it was designed for.
Now let’s be clear — every RV could be built better. No argument there.
But these things are built fast, by humans, on assembly lines. There will always be imperfections.
The bigger issue is expectation vs reality.
Same way you wouldn’t expect a budget tool to perform like a professional one… you can’t expect an entry-level RV to hold up like a high-end full-time unit.
This is why people end up frustrated.
Not because every RV is trash —
but because they bought a “good” RV and expected “best.”
If the industry was more upfront about this, you’d see way fewer complaints.
So before you buy, ask yourself:
Are you weekend camping… or actually living in it?
Because that answer determines what level RV you actually need.
• good better best RV explained
• entry level vs high end RV
• RV tiers explained
• budget RV vs luxury RV
• what RV should I buy for full time living
• best RV for full time living vs weekend camping
• RV buying mistakes to avoid
• choosing the right RV for your lifestyle
This is one of the most common things I see, and 9 times out of 10, your awning isn’t broken… it’s just out of adjustment.
In this video, I walk you through exactly how to fix it using ONE tool. No replacing arms, no expensive repairs, no guessing.
Most people start adjusting the arms… and that’s where they go wrong. The real adjustment is in the fabric, not the arms.
We cover:
• Why your awning looks bent or uneven
• What causes fabric to shift on the tube
• Where the gimp/set screws are located
• How to center the fabric on the tube
• How to align it at the RV wall
• Why trial and error is part of getting it perfect
• How to fix wrinkles, twisting, and bad roll-up
If your awning is favoring one side, not closing properly, or looks like something is bent… watch this before you spend money.
All products and tools I use are available here:
👉 thatrvtech.com
Subscribe for more no-BS RV tech tips, real-world diagnostics, and fixes that actually work.
In this video, I break down one of the most common complaints I see with Lippert leveling systems—constantly having to re-zero, inconsistent leveling, and systems that just won’t hold level from one stop to the next.
Here’s the truth… it’s usually NOT a bad sensor.
It’s the rear level sensor, and more specifically, how it’s mounted.
If that sensor is loose, zip-tied, hanging, or has shifted even slightly, your system will never know what “level” actually is. You can recalibrate it all day long, but if that sensor moves, your problems are coming right back.
In this video I show you:
• Where the rear level sensor is located
• What it looks like
• Why it causes constant leveling issues
• How improper mounting throws everything off
• What you need to check before replacing parts
If you’ve been chasing leveling issues and nothing seems to fix it… check this before you waste time or money.
All products and tools I use are available here:
👉 thatrvtech.com
Subscribe for more no-BS RV tech tips, diagnostics, and real-world fixes.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
It’s also one of the few things I can teach that applies to almost ALL RVs.
But it gets messed up ALL the time.
The biggest key?
👉 Proper use.
First thing — water is everything.
After you dump, or before you start using your RV, you need to prime the tank with a few gallons of water. If you don’t, you’re asking for problems.
Next — when you use the toilet:
This isn’t your house.
There’s no big rush of water helping things move.
Before a #2, fill the bowl with water (just lightly press the pedal). Then when you flush, hold it down for a few seconds.
Think of it like a water slide…
If they shut the water off right away, you’re not going very far 😅
Same idea here — everything needs enough water to make it all the way to the tank.
Now let’s talk treatments…
Not all tank treatments actually break down waste.
A lot of them just turn everything blue and try to cover the smell.
That’s not what you want.
You’ve got a 30–50 gallon tank of waste under your feet — you need something that actually breaks it down, not just masks it.
The good ones use enzymes to do that.
Out of everything I’ve used, there’s only a couple I actually trust — and Liquified is at the top of that list.
You can grab it online or even find it at some Walmart locations and dealers.
Bottom line:
If you want a black tank that flows right and doesn’t stink…
👉 Use more water
👉 Flush longer
👉 Use the right treatment
Simple as that.
want to try Liquified RV Toilet Treatment? you can find it here: amzn.to/3Pwva4q
Disclosure:links in this post may be affiliate links. That means if you choose to purchase through them, I may earn a small commission — at no extra cost to you. I only recommend products I actually use, trust, and would stand behind in the field. No BS, no paid hype.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
some jokes just write themselves...
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
These are the non-negotiable essentials every RV owner needs before hitting the road—things that protect your rig, keep your water safe, and make setup way easier.
We’re talking:
• Drinking water hose (not your garden hose)
• Water filter
• Water pressure regulator (because blown lines aren’t fun)
• 90° hose adapter for tight hookups
• A quality dump hose (you’ll thank me later)
• Toilet tank treatment
• Surge protector / EMS to protect your electrical system
• Wheel chocks
• Leveling blocks & stabilizer pads
Skip these, and you’re risking damage, headaches, or a really bad campsite experience.
You can find all products that I recommend on my website thatrvtech.com
Save this so you don’t forget anything before your first trip—and if you’ve been RVing a while, you already know every one of these earns its place, and your welcome to chime in on what you consider a must have.
#Rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp
RV owners — this is one of the most overlooked problems I see.
Everyone looks at cargo carrying capacity (CCC)… but almost nobody actually subtracts what they’ve already added.
👉 Solar systems
👉 Slide toppers
👉 Extra batteries
👉 Inverters
👉 Aftermarket upgrades
That’s NOT “free weight” — that’s permanent weight, and it comes straight out of your CCC.
And it doesn’t stop there…
Everything you load into your RV adds up:
• Water
• Gear
• Tools
• Food
• Clothes
• Passengers
It all counts.
In this video I break down:
• Why most RVs are heavier than owners think
• How upgrades like solar silently eat your capacity
• The difference between dry weight, GVWR, and CCC
• How to actually stay within safe limits
This isn’t about being picky — this is about safety, tire failures, suspension damage, and control of your RV on the road.
Most RVs out there right now are overweight.
The question is… is yours?
If you want real, no BS RV education — subscribe.
I see this mistake all the time, and honestly, a lot of it comes from bad info in sales or advertising. So let’s clear it up:
👉 Stabilizers are ONLY meant to stabilize your RV
👉 They are NOT designed to level your camper
👉 Trying to use them to level can cause damage
If your RV doesn’t have a leveling system, you’re doing it the old school way — leveling blocks and ramps under your tires. That’s the correct method. Always has been.
Stabilizers come AFTER you’re level — not before.
And yeah… I know that’s not what a lot of people were told.
If you want real, no BS RV education — you’re in the right place.
#rv #rvtechnician #rvlife #rvdiy #rvtips #camper #campertips #rvmaintenance #rvrepair #thatrvtech #rvhelp


