bobflyman
GitUp Git 2 vs Firefly S6 gyro stabilised action cameras - vs SJCamx1000 non gyro
updated
I bought the Mythos here (I'm not on commission, it really is lovely to fly!) Sorry £35 now.
robotbirds.co.uk/tech-one-mythos-epp.html
I believe this is quite an old kit now. See my build blog which I think is a good improvement on the original build plans. Mythos build youtube.com/watch?v=-1mNk0KknTo&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=9&pp=gAQBiAQB
Lidl Spitfire youtube.com/watch?v=N-z45QNjyZ8&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=17&pp=gAQBiAQB
youtube.com/watch?v=lSaW-cT0wm4&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=42&pp=gAQBiAQB
00:00 Introduction
00:42 Lidl RC conversion Spitfire takes off from the ground
02:16 Ooops. Broken prop.
02:51 New prop but right hand 2 bladed - Try again
04:06 Tech One Mythos takes to the air
05:46 And on HIGH RATES!
08:28 Lidl Glider RC Biplane conversion flies
09:28 Outro
Always use an appropriate charger and do not leave unattended. And it's wise to use a BMS protection circuit board if making a battery with 2 or more cells.
Plus, don't use cross weave filament tape on ailerons!
Note: it really needs a smaller propeller if I use the 800mA 3s, but OK with the 1000mA 2s.
00:00 Introduction
01:30 The plan
02:30 Nose surgery
03:26 Success
03:48 A TOP TIP
05:11 But where is the battery now?
Parts list:
Full parts list. Motor for 'heavy' build as shown, plus speed controller AND propeller here for just £14 or less !!! banggood.com/custlink/3mKEPaklON
Smaller Motor lighter build, Motor Emax RS2205-2300 banggood.com/custlink/vDKRHlqilf
propellers 2 Pairs LDARC 5x4.5x3 5045
banggood.com/custlink/3vDrdrgONR
20A ESC Speed controller banggood.com/custlink/GmDyHOUSNB
4 x 9 gms servos banggood.com/custlink/3GDdVaqiAE
You obviously need a receiver and transmitter.
I use Flysky fs i6 which is a good 20 channel budget 2.4 Ghz transmitter.
FlySky i6 with a receiver banggood.com/custlink/DG3cyr4Beh
Single motor Lidl Chuck glider build youtube.com/watch?v=gj4lk1SLVDU&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=10&pp=gAQBiAQB
My Mini Flight Test F22 build youtube.com/watch?v=oHKjY_CZOVo&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=7&pp=gAQBiAQB
00:00 Introduction
00:58 FT Mini Raptor F22 maiden with bigger motor
04:01 Mini Lidl twin motor maiden
Easy to follow complete build blog and full parts list.
Chapters below.
Glider Lidl £5 when they have them in, or E bay etc. £6.99 Search 'Mini Chuck glider'
Motors I used 2 x 8.5 x 20mm Brushed Motors 1.0mm Shaft CW and CCW 8520 Coreless Motors £9.58 Amazon free with Prime amzn.to/3AFmoq9
AliExpress and E bay were sources.
Flysky FS2A 4 channel mini receiver £4.01 + £1.70
Ultra Light Brushed ESC Single Way 5A or 10A £3.96 Free shipping
4 props 2 cw and 2 ccw £2.34 + £1.79 E Bay
2 x 3.7 gms servos ali express £1.55 + £1.61
Total around £34
My lipo was £5 in a local shop 250mA 1s lipo
You'll need a glue gun, thin wire, soldering ability, craft knife, Uhu Por ...
Music courtesy of YouTube audio library
chapters:
00:00 Introduction
00:16 Build blog
00:36 remove canopy and hollow out fusilage
00:54 Install aileron servo
01:34 Cut ailerons
03:50 Cut elevator
06:04 fit tailplane
07:07 the electrics
07:27 fitting the two small brushed motors
07 :28 AND MY NOT DELIBERATE MISTAKE
08:15 don't do it this way either
09:01 Houston we have a problem
09:52 sorted
10:12 covering burn holes!
11:00 Connecting ailerons
12:27 Installing elevator servo
13:39 Installing electrics
14:21 EVERYTHING IS WORKING!
14:25 connection elevator
15:14 my canopy mod saves 7 gms and looks great!
16:06 FINISHED
Clue. Mini F22 needs a bigger motor.
00:00 Introduction
00:12 At the strip
00:40 My scaled down Flight Test Mini f22
01:12 Trim change needed
01:31 Try again
02:04 Super light Fusion
03:12 Know when to quit?
03:18 Changes are made and outro
Mini F22 build youtube.com/watch?v=oHKjY_CZOVo&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=3
Dohnuts Models Fusion youtube.com/watch?v=Gbubm15TrYM&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=1
Mini Lidl chuck glider build youtube.com/watch?v=gj4lk1SLVDU&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=7
My Lidl Spitfire youtube.com/watch?v=N-z45QNjyZ8&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=12
Like the saying goes, any landing you can walk away from is a good landing!
#shorts
#paramotor #paramotorfail #paramotorcrash
#paramotor
Fake SSD scams. Beware.
Download media tester here. github.com/dkrahmer/MediaTester/releases
Music courtesy of YouTube audio library.
00:00 Introduction the story
01:19 Making a start - cutting out
02:31 We have the start of a model!
03:36 Maybe it'll be Plan B?
04:48 Starting Plan B
05:33 Working out where to put components for CoG
06:29 Installing motors and I make a mistake!
08:22 We all need helping hands.
09:50 Motors in and a TRUE CONFESSION. MY MISTAKE!
11:56 Summary and outro
The kit can be bought here : robotbirds.co.uk/donuts-models-nano-fusion.html
I am not on commission!
Brushless motor banggood.com/custlink/3mGJ802DOu
Servos 3.7 gms banggood.com/custlink/vKGc0u9h9Q
ESC speed controller banggood.com/custlink/GmDyHOUSNB
I bought my kit here £34.94 (other sellers are available!)
align-trex.co.uk/tech-one-mythos-epp.html
This is my detailed build blog for my 50% scaled down Flight Test F22 Raptor.
Parts list is below and links to plans etc.
Motor is now BR 1806 and 5040 twin bladed prop
banggood.com/custlink/KDvPv0RMSO
Chapters:
00:00 Introduction
01:28 Getting started
02:33 Print scaled down tiled plans, cut out foamboard and my design changes
03:58 Taking shape now
05:30 Fitting brushless motor and a clever idea for making a template
06:10 Some gluing done now
07:08 Mounting the flaperons and 35 mm film hinges!
08:03 Getting the CoG right - tips
09:55 Motor now fitted and a bit of decoration while waiting for servos
10:38 90% complete - servos in - electrics finished
11:19 ALMOST HAD A DISASTER !
12:37 Finished, summary and outro!
Parts list:
FS2A 4CH AFHDS 2A Mini receiver
banggood.com/custlink/3D3pgwSh86
Racerstar BR1104
banggood.com/custlink/vKGc0u9h9Q
3.7G Miniature Analog Servo 3.7 gms
banggood.com/custlink/mDKWewZElL
10 amp brushless esc
banggood.com/custlink/GGvc2JVtZB
GWS Ep3020 Microfly Prop
wheelspinmodels.co.uk/i/88561/?gclid=CjwKCAiAzp6eBhByEiwA_gGq5IWyiHpt8B5q-KnuU3mRuEktaUHYZIatL1yf2BIm4wtgHG7wn19XuhoCh0AQAvD_BwE
Lost model finder
banggood.com/custlink/3DvYn8tHyn
Sheet of 5 mm foamboard, hot glue gun and thin wire for control rods.
You may need a small drill to get the prop to fit the 1.5 mm dia motor shaft:
Plans:
flitetest.com/planes#/listSort=date_high_to_low
The original bigger version flitetest.com/articles/ft-22-raptor-build
Plans:
s3.amazonaws.com/plans.flitetest.com/stonekap/FT-22-plans.pdf
Tiled plans s3.amazonaws.com/plans.flitetest.com/stonekap/FT-22-TILED-PLANS.pdf
You can use some versions of free Adobe Acrobat or Reader to scale down plans.
helpx.adobe.com/acrobat/kb/scale-or-resize-printed-pages.html
Module I used was Bluetooth 5.0 Stereo Audio Receiver Module Board here. Quick delivery.
kunkune.co.uk/shop/uncategorized/bluetooth-5-0-stereo-audio-receiver-module-board/?gclid=CjwKCAiAl9efBhAkEiwA4Torit8OE2eVw-LCDS48suJiDmbejkIGKgAq2phsqpaFzeN0fAzJ_wRycRoCcuQQAvD_BwE
The foam was cheap. A scrap of insulation foam I found in a skip! Quite firm and high density, but very light. Still haven't built a unicycle and learned how to ride it. That was the other project.
Motor E Max 2805
3 blade 5X4 prop
800mA or 1000mA 2s lipo
20A ESC
2 x 9g servos
Foam cutter video is here youtube.com/watch?v=nLZ-FmEu8KA&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=15
00:00 Introduction
00:58 Test flight one
01:48 Test flight 2 after a little trimming
02:48 More trimming
05:03 Finally nicely trimmed
I had some frog spawn as early as 4th Feb this year, but I suspect I'm going to get more.
Frogs aren't exactly romantic, no foreplay, and you wouldn't call them handsome, though I suppose lady frogs find them attractive. They put it about a bit too. A male may mate with several females in a night.
Lidl Stumpy 2nd flight? Maybe not so good. :(
Build blogs for all on my channel and LOADS of Lidl Glider RC conversions!
Mini Lidl Build blog youtube.com/watch?v=gj4lk1SLVDU&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=2
4 motor Mini Lidl Build youtube.com/watch?v=p3L6NqLW6hs&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=5
4 motor mini Lidl maiden youtube.com/watch?v=dblaEBBsxuw&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=4
Lidl Spitfire 1st Maiden youtube.com/watch?v=Pr2EZT_-ib8&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=3
Lidl Spitfire Build Blog youtube.com/watch?v=N-z45QNjyZ8&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=7&t=0s
00:00 Introduction
01:34 Mini Lidl Maiden 1
03:20 Mini Lidl Maiden 2
04:16 Mini Lidl Maiden 3
05:18 Lidl Spitfire 2nd Maiden flight
07:28 Lidl Spitfire again with 3 blade prop 5040
09:15 Outro
All you need is 3 small pins, wire, 5 minute epoxy and soldering iron.
PS Suitable chargers and adapter leads of various kinds are available of course.
Full parts list below.
00:00 Introduction
30:49 Jump to Summary
or all chapters here:
00:00 Introduction
00:27 Components I plan to use and their weight and basic plan
02:41 Hollowing out the body
03:16 First remove canopy and counterweight
04:35 It's hollowed out and my tool
05:21 How will I fit ailerons? I servo or two?
05:56 I use one servo!
07:12 Cutting the ailerons
13:21 Test and centre servo before installing - Servo testers
14:52 This is how centre servo is intended to work
15:31 So how can I make an elevator for this?
19:12 Elevator sorted apart from servo.
20:24 Fitting BR1104 brushless motor - first step a small bulkhead
23:45 Motor step 2, gluing in position - but before that ...
24:12 ... test components before fitting - TOP TIP
26:09 Motor glued on.
26:26 And how to reverse direction on a brushless motor
26:33 Electrics and the Lipo I will use. 200mA 2s
27:10 How I make operating levers for ailerons.
28:04 Servo for ailerons installed and ailerons connected
28:48 Deciding location for elevator servo.
30:11 All up weight now!
30:50 Running and first summary
31:58 Closer look at electrics installation
32:24 The final stages of the build
33:30 Receiver installation
35:03 Elevator servo fitted and attached and winding up summary!
Parts:
Mini Lidl glider £6.79 at this time amzn.to/3kwTR14
Mini receiver £7.65 banggood.com/custlink/3D3pgwSh86
BR1104 Brushless motor £5.11 banggood.com/custlink/vKGc0u9h9Q
3020 propeller about £5 with post wheelspinmodels.co.uk/i/88561/?gclid=CjwKCAiAzp6eBhByEiwA_gGq5IWyiHpt8B5q-KnuU3mRuEktaUHYZIatL1yf2BIm4wtgHG7wn19XuhoCh0AQAvD_BwE
3.7 gms servo £5.35 each banggood.com/custlink/mDKWewZElL
200mA 2s lipo My local shop it was £5. shop around. Google!
10 amp brushless esc - this one looks OK, you may need to search £12 with delivery
Search e bay 'Hornet 12a ESC Brushless Motor Plane Speed Controller RC 12 Amp' UK Seller 10a
plus you need small wire for control surface links, bullet connectors, heat shrink ...
Lidl Spitfire Build Blog here :
youtube.com/watch?v=N-z45QNjyZ8&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=4
And what's useful when you can't find a model in the trees 'cos you lost control of it? Yes, a model finder! Video is here.
youtube.com/watch?v=aWL-3Lu-xp8&t=0s
One short Stumpy test and two Lidl Spitfire flights. Chapters below.
00:00 Introduction.
00:20 Lidl Spitfire takes off from the ground
01:56 Lidl Stumpy maiden
03:09 Lidl Spitfire flight two
04:30 I lost the plot
05:19 Now where is it!
05:37 Model finders are worth their weight in Gold!
06:03 Summary
Build blog is here. youtube.com/watch?v=p3L6NqLW6hs&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=2
£5 chuck glider + £10 drone = 4 engined RC plane. Or how to build a 4 motor RC mini plane using parts from a mini drone.
00:00 Introduction
00:46 The idea
03:50 Making a start on the project
05:20 Taking the drone apart
08:21 Installing the PCB
09:49 wiring up the drone motors
11:42 Fitting the motor cases on the wings
12:40 Installing motors
15:25 They are in and connected and 1st test
18:08 Nearing the finish and summarising the build
Please check out my other Lidl glider builds, singles, twins, biplanes, even Vulcans.
Music YouTube Audio Library.
Highway One - Steve Adams
Nebular Focus - Steve Henig
Nineties Pad - Brian Bolger
Oceanside Bonfire - The Great North Sound Society
The laptop is Acer Aspire 6, specifically - 51 52ES, but the process will be similar for HP, Dell, ASUS, MSI, Lenovo, Samsung, or any other brand of laptop. Tools required: small crosshead screwdriver.
Laptop was 6 years old and battery life was now very poor, after fitting my new battery I'm getting 4 hours.
00:00 Introduction
00:30 Removing the case back
02:54 Moving the hard drive
03:52 Removing the battery
04:26 Houston we have a problem
06:04 Sorting the problem
08:33 At last the new battery goes in
09:44 Putting laptop rear casing back on
12:19 Testing my work
This is my no 9 conversion. I've made singles, twin engine, Biplane, Vulcan and edf. For a full detailed Lidl RC conversion how to do it video see my original vid here, 50k views now ...
youtube.com/watch?v=ceNpxgB62Gk&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=2&t=0s
or my Lidl Spitfire video, also very detail build blog here
youtube.com/watch?v=N-z45QNjyZ8&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=1
00:00 Introduction
00:45 Starting with the wing
01:36 Wings are glued on
02:10 Almost finished
02:58 Parts, motor, propeller, servo fitting, etc
05:54 Finished CoG, fitting ESC etc.
06:03 Model finders - don't lose that plane!
Parts list
Model finders 3 for £9 banggood.com/custlink/3DvYn8tHyn
2 x 9G Micro Servo Motors amzn.to/3WAEwvi
DXW D1806 1806 2280KV 2-3S Brushless Motor banggood.com/custlink/3mGJ802DOu
3 blade 4045 propeller banggood.com/custlink/GvDr80kDgh
2 blade 4050 hobbyking.com/en_us/gemfan-5045-grp-nylon-propellers-cw-ccw-set-green-5-x-4-5.html?___store=en_us
20 amp esc - speed controller coolcomponents.co.uk/products/electronic-speed-controller-20a
servo tester for centering banggood.com/custlink/vDKcS0zvg9
FlySky FSi6 transmitter banggood.com/custlink/v3GrI6zvbS
FlySky iA6 receiver banggood.com/custlink/GKvC94kvb0
other stuff:
glue gun amzn.to/3E1hjem
twin engined Lidl glider RC conversion
youtube.com/watch?v=NtOu8cE9X9o&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=5
Biplane build blog
youtube.com/watch?v=lSaW-cT0wm4&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=24
1st Vulcan
youtube.com/watch?v=Ol16GD2p0PE&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=20
EDF build blog
youtube.com/watch?v=2CE7HTWzotk&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=2
EDF Vulcan
youtube.com/watch?v=VTjSyig2jIE&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=3
Centre of Gravity calculator https://rcplanes.online/cg_calc.htm
00:00 Introduction
00:17 The long drive south from Dunkerque
01:17 1st stop by the Rhone
01:47 Col de Sapenay
02:20 St. Hilaire du Touvet on my way south
02:38 Heading further south
03:40 The James Bond Road - Route de Napolean
04:04 Greolieres
04:15 Rough first flight!
10:36 3rd flight
15:37 Going north again on the James Bond road in the rain
19:12 The Biggest Flying Festival in the World - The Coupe Icare 2022
23:49 The road home
You will need :
Lidl Glider - only in the shops once a year Springtime
3 x 9G Micro Servo Motors amzn.to/3WAEwvi
DXW D1806 1806 2280KV 2-3S Brushless Motor banggood.com/custlink/3mGJ802DOu
3 blade 4045 propeller banggood.com/custlink/GvDr80kDgh
2 blade 4050 hobbyking.com/en_us/gemfan-5045-grp-nylon-propellers-cw-ccw-set-green-5-x-4-5.html?___store=en_us
20 amp esc - speed controller coolcomponents.co.uk/products/electronic-speed-controller-20a
servo tester for centering banggood.com/custlink/vDKcS0zvg9
FlySky FSi6 transmitter banggood.com/custlink/v3GrI6zvbS
FlySky iA6 receiver banggood.com/custlink/GKvC94kvb0
other stuff:
glue gun amzn.to/3E1hjem
Spitfire wing plans here: aerosociety.com/media/4843/the-spitfire-wing-planform-a-suggestion.pdf
chapters
00:00 Introduction
01:10 Straightening the wing - removing dihedral
05:32 Plans to change the wing profile to similar to the Spitfire
and giving the wing a slight sweep
07:55 Cutting and gluing the sweep
13:06 Cutting and making the ailerons
15:31 Installing main wing servos
18:59 Hollowing out the nose and fusilage
19:46 First remove the nose cover
21:33 How I hollow out the nose - hot wire tool
23:44 Improving the tail shape
25:28 Installing aileron servos
26:20 Centre servos before installing!
27:33 Cutting the elevator
31:16 Elevator servo fitting
31:54 What brushless motor and propeller, esc, lipo will I use?
35:24 Connecting servo to aileron - my easy method
36:26 Ailerons and elevator connected and testing motor, esc, prop sizes etc.
37:23 How do you change rotation direction of a brushless motor?
37:39 Final assembly and what I've done
37:53 Motor and props I tested - power test - prop hanging
40:23 Model finders
40:47 The electrics
40:52 Centre of Gravity CoG
42:13 Getting CoG right and summary
My other build blogs:
First solo Lidl RC build
youtube.com/watch?v=ceNpxgB62Gk&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=1
twin engined Lidl glider RC conversion
youtube.com/watch?v=NtOu8cE9X9o&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=5
Biplane build blog
youtube.com/watch?v=lSaW-cT0wm4&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=24
1st Vulcan
youtube.com/watch?v=Ol16GD2p0PE&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=20
EDF build blog
youtube.com/watch?v=2CE7HTWzotk&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=2
EDF Vulcan
youtube.com/watch?v=VTjSyig2jIE&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=3
Centre of Gravity calculator https://rcplanes.online/cg_calc.htm
If you're a YouTuber, be sure to watch this video and stay safe! This is a scam, and if you fall for it, you could have your personal information stolen from your PC and lose a lot of money.
Be sure to watch this video and stay safe!
#shorts
I worked it out in the end. ;) . And went straight up like I was in an elevator. Nice flight.
Music courtesy of YouTube Library
American Idle - RKVC
Cosmic Drift - DivKid
Drifting at 432 Hz - Unicorn Heads.
00:00 Introduction
03:51 Removing the NiMh batteries
05:25 Putting in new batteries
08:49 Fitting circuit board back
09:16 Putting case back together
12:26 I'D FORGOTTEN A GASKET
18:08 The tricky bit with little springs
19:11 The last two screws! Hooray.
20:37 Is it going to work now? :(
20:51 How it comes apart (in short)
22:11 Wind up
Take care if you decide to remove and replace the front screen. :(
The MegaRide™ starts from Lee Mill Industrial Estate, the bikers start arriving from around 9am. They leave at 11.30 and head along the A38 towards Marley Head where the bikers will cross the flyover and back down the A 38 towards Plymouth, following a route through the Plymouth City Centre with the ride ending on Plymouth Hoe. I was late at the start as my mate's 1971 Kawasaki broke down on the way.
Cameras used. Akaso Brave 6 plus front helmet. Caddx Orca helmet back facing, On the Hoe, SJCam SJ9 Strike.
Music courtesy of YouTube audio library.
Retribution - NEFFEX
Cosmic Drift - DivKid
Blue Day - Freedom Trail Studio
SJCam SJ9 Strike was produced briefly by SJ Cam , totally waterproof camera. Great 4K video with EIS, but awful audio I think that's why they ceased it.
Music: YouTube audio library.
Nebular Focus - Dan Henig
Drifting at 432Hz - Unicorn Heads
£47.99 amzn.to/3Peas3R 2.4G Remote Control - 2 Rechargeable Batteries - wifi app and Accessories Kits.
00:00 Introduction - what you get
01:40 Putting battery in and charging
03:00 Test clips
07:50 How to use the camera basics
11:54 Changing settings
13:28 Changing video resolution
14:22 Turn on EIS (Gyro stabilisation)
15:09 Using the wifi app Live DV
17:33 Using the wrist remote
18:27 Summary and useful links
Built-in 3-axis stabilization gyro keeps the images stabilized in place and ensures clear and stable images and videos. The camera also comes with helmet accessories which makes the camera a helmet camera. Other accessories can make it a bike camera, surfing camera, canoe camera, snorkeling camera, or vlog camera.
video resolutions available: 4K/30fps, EIS 2.7K/30fps, EIS 1080P/60fps, EIS 1080P/30fps, EIS 720P/120fps. It has a 20MP photo resolution and other resolutions from 8MP to 20MP available.
Lovely long deserted beaches too.
The lowest temperature it can reach depends on the use of space and the temperature of the environment. Generally speaking, the smaller the space and the lower the ambient temperature, the lower the temperature can be achieved.
Peltier Kit e bay £11.88 now ebay.co.uk/itm/194961865884? hash=item2d64a1fc9c:g:9C0AAOSwHy1iTrEw or just search
Peltier unit built with internal fan assembled £15 amzn.to/3z9tPWZ
A better unit that I intend to fit next time £18 banggood.com/custlink/m3vYzqcBLg
small pc computer fan 40 mm e bay search
Ecotherm board 8 x 4 sheet 25 mm £18 or so builderdepot.co.uk/25mm-ecotherm-eco-versal-insulation-2400mm-x-1200mm-8ft-x-4ft or just use local builders merchants for similar.
No more nails Amazon £8 or you possibly have a tube of silicon lying around ;) amzn.to/3z9OJoT
My box came from The Range. 35 ltr storage box. Cheap.
00:00 Introduction
02:45 Peltier module quick look - how do they work
03:19 Building an insulated box
05:34 Assembling a peltier module unit
11:19 Dry installation of the peltier cooling unit
12:34 Testing starts!
13:14 Proper testing starts
14:29 Almost finished and some conclusions
16:40 And the thermostat!
18:55 Final conclusions
Xiaomi 360 Sphere camera.
Music courtesy of YouTube Library
Drifting at 432 Hz - Unicorn Heads.
Parts on my lightweight Versa
CF2805 2800 kv brushless motor (or similar) banggood.com/custlink/DmDEVjMlgf
9 gm servos SG90 Mini Gear Micro Servo 9g banggood.com/custlink/3GDdVaqiAE
Airfoil profile database : http://airfoiltools.com/airfoil/details?airfoil=clarky-il
Original FT Versa plans here : forum.flitetest.com/index.php?threads/ft-versa-wing-build.5096
Mine had a nose which helps with CoG . Video here youtube.com/watch?v=uTmxfCvwHS0&list=PLLdle7NDE_1Y_XC3kjOSIUDJcRxVrhez-&index=43&t=0s
And Mighty Mini Arrow here : s3.amazonaws.com/plans.flitetest.com/stonekap/FT%20Mini%20Arrow%20v1.1%20Tiled.pdf
00:00 Introduction
00:58 DIY easy hot wire foam cutter
01:54 My method for cutting
09:37 The more usual template method for cutting a wing profile
12:42 Cutting delta shape wings from foam
16:12 My Foam Versa begins to take shape
18:45 Ailerons
19:07 Summary
You can buy the bluetooth amp here :
DollaTek 100W+100W Bluetooth 5.0 Power Audio Amplifier board
£10.99 amzn.to/3k8s7MV £10.99
BOSS Audio Systems CH6530B Chaos Series 6.5 Inch Car Stereo Door Speakers
USA amzn.to/38iXams $32.99
Similar Boss Audio CH6500 Chaos Exxtreme Series 2-Way Speakers
UK amzn.to/3L715S1 £26.95
Music : American Idle - RKVC
00:00 Introduction
00:28 Installation in my van
02:51 Unboxing the DollaTek 100W+100W Bluetooth 5.0 Power Audio Amplifier
04:09 Bench testing the DollaTek 100W+100W Bluetooth 5.0 Power Audio Amplifier before install
07:11 Assembling the DollaTek 100W+100W Bluetooth 5.0 Power Audio Amplifier
08:18 Finished and testing
Overall cost was about £2,000 including £500 for the windows fitting, £309 for the cooker/sink combo and £120 for diesel heater. (Plus I probably forgot to add a few bits and pieces!)
Materials used.
If you buy from Amazon I will get a small commission, helps keep my channel going!
maXpeedingrods 12V 2KW Diesel Air Heater amzn.to/3jNdHSq reduced to £92.99 NOW
Dodo Mat DEADN Hex sound deadening mat amzn.to/3jRwRpX
3M x 1M Car Sound Proofing Foam amzn.to/3jJgqfk
Heat Resistant Sealant 1300 C - 310ml amzn.to/3JWcrqM
1m x 5m 10mm GlassMAT XR Foil Vapor Barrier amzn.to/3KZMc3K
4 Way Super Stretch Lining Carpet amzn.to/3JZ7ddA
Cooker / sink combo ebay.co.uk/itm/353695199248
5 Gang Switch Panel, 12V 24V Inline Fuse Box LED Switch Panel amzn.to/385P6Fu
4 x 12V LED SPOTLIGHTS/DOWNLIGHTERS amzn.to/388WHn6
00:00 Introduction
00:26 Strip out the van
00:31 Sound deadening , vapour barrier
00:45 Insulation
00:56 Fitting windows
01:24 4 way stretch lining, that's the BIG job
01:47 The ceiling - uPVC cladding a van ceiling
02:16 Fitting out - building furniture - that's a BIG job
02:46 Sink cooker combi unit
03:15 Fitting a Chinese Diesel Heater
03:42 DISASTER!
04:07 Back on the job - and cooker and sink unit
04:52 Carpet tiles and finishing touches. Lighting.
05:30 FINISHED!
I get a small commission if you use these links.
maXpeedingrods 12V 2KW Diesel Air Heater amzn.to/3jNdHSq reduced to £92.99 NOW
Dodo Mat DEADN Hex sound deadening mat amzn.to/3jRwRpX
3M x 1M Car Sound Proofing Foam amzn.to/3jJgqfk
Heat Resistant Sealant 1300 C - 310ml amzn.to/3JWcrqM
00:00 Introduction
00:21 Why I bought this heater
01:56 Unboxing the Maxspeedingrods Chinese diesel heater
05:59 Sound proofing the fuel pump
09:17 Installation and some tips
10:16 TRUE CONFESSION
14:38 Summary
Best results if you use some kind of external antenna.
DIY antenna I use. youtu.be/Y_fE2dQK1xs
Also works on my Windows 10 laptop with TotalMedia 4.5
climaxdigital.co.uk/ClimaxDigital-DTV330-Mini-USB-DVB-T-TV-Receiver-Stick-Freeview-Remote


