Nintendo PlayStation Prototype: Finally Working! element14 presents 2017-05-05 | It’s been almost a year since the Team met Terry Diebold and his Nintendo-Playstation prototype at the 2016 MGC (Midwest Gaming Classic). They have a month to give it back to him at the next Midwest Gaming Classic and their goal is to have it back to him in working condition. Visit the Ben Heck page: http://bit.ly/2pdwrM4Live Stream of Nintendo-Playstation Protoype Part 1: http://bit.ly/2qLMeD5Live Stream of Nintendo-Playstation Prototype Part 2:http://bit.ly/2paRELCEnter to Win on the Techno Toys Competition: http://bit.ly/2pdrPFuThere are two digital-to-analog converters (DACs) on the prototype. One of them is for the Super Nintendo side and one of them is for the CD ROM side. They are muxed together after that. DACs take digital streams and turn them into analog signals – audio in this case. Ben has the prototype hooked up to an Oscilloscope so he can take a closer look at it. He checks the signal for the music from Super Mario Kart and is able to determine that the Super Nintendo DAC is working. The CD rom DAC, which is side by side with the SNES DAC, is not working however. Ben’s been doing some mapping of the schematic and thinks he knows what a mystery chip does. Its probably some sort of BUS location decoder chip. Someone has mapped out what data you send out from the expansion port. The chip let’s you talk to other chips on the board based on what type of register is sent out. Ben continues mapping out the chip in order to give him more points from which to test things. After replacing several questionable capacitors off-camera and jiggling some things around, Ben returns to the shop to find that CD ROM on the Nintendo-Playstation prototype is suddenly working. On the board there is a CD ROM controller chip, a digital signal processor, and there’s also a microprocessor on a connected board. When the system is not in game mode, the microcontroller on the connected board tells the CD ROM controller on the motherboard what to do (such as play music). Ben checks the ribbon cables and takes measurements from the three potentiometers on the driver board for the disc. Ben attempts to get a disc to boot up a game disc. A SNES program is sending commands to the NEC microcontroller, telling it to do disc functions. These commands (and data) would have gone over the expansion bus if this had been a SNES add-on. Super Boss Gaiden loads to black screen so progress has been made. No one has actually made games for the Nintendo-Playstation prototype, the Super Boss Gaiden game was programmed for an emulator. After making adjustments to the burn disc, Ben is able to successfully get a game to run!Disclaimer: http://bit.ly/2qLz4Ge
LoFi Beats To Solder To element14 presents 2024-08-16 | Pick up your soldering iron and chill out as you focus and get into your zen headspace, kick back and listen to these LoFi beats in the background as you join the element14 presents team working away on their printed circuit boards. Let the stress melt away to the sizzling sounds of flux and paste as the components wick and slide into place. Whether it's leaded solder, unleaded solder or solder paste, whip out your solder sucker and solder wick and get to work: bit.ly/46NjfDQWant more soldering related content? Who doesn't! Check out these past episodes:-DIY Hot Plate for SMD Soldering Using Raspberry Pi Pico: bit.ly/4dNAvuX-Learn to Solder: bit.ly/4fPdZUi-Make your Own Auto-Sensing Solder Fume Extractor: bit.ly/4drq7t8Feel inspired to get soldering but need some equipment? Check out a range of soldering stations here: bit.ly/3yKdDxNVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5Bux#lofi #soldering #element14community
DIY Single Board Computer with esp32 and Raspberry Pi Pico! element14 presents 2024-08-07 | Why have one single board computer when you can stack them? Watch as we turn an ESP32 and Raspberry Pi Pico into a Franken-SBC that’s both weird and wonderful. Because normal is boring! 😂🔧 #DIYTech #GeekLife
DIY Single Board Computer with ESP32 and Raspberry Pi Pico element14 presents 2024-08-02 | After flashing Linux to an ESP32-S3 and turning an RPI pico into a GPU, Clem logically has to do the next step and create a cursed DIY SBC. And because it is not remotely weird enough for his twisted taste, he also makes it connectable to a Raspberry pi so you can have a single board computer on your single board computer... and even weirder shenanigans! Check out the full episode blog on the #element14community - bit.ly/3YtqAXdRelated Content:Episode 623 'How to run Linux on an esp32' - bit.ly/3YmVTD4 Episode 644 'Turning a Raspberry Pi Pico into a GPU' - bit.ly/3LNxE9v #0:00 Welcome to element14 presents#0:20 Overview#1:08 Build A PCB#2:30 What To Do With It?#5:31 What Could Go Wrong...#9:01 Clem's Cronenberged SBC#12:43 Getting It Up And Running#15:46 What IS All This Good For?#17:14 Give your Feedback#raspberrypi #linux #pico #sbc #DIYgpu #DIYsbcEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Workbench Wednesday: Hands-On with PicoScope 7 #picotechnology #picoscope #element14community element14 presents 2024-07-31 | James dives into Pico Technology's latest PicoScope oscilloscopes software, PicoScope 7. Using a PicoScope 2000A James walks through key measurements and demonstrations using the built-in arbitrary waveform generator. He explores new functionalities in PicoScope 7, such as the improved UI, a unique feature called DeepMeasure, and decoding I3C traffic. Read the full episode blog on the #element14community : bit.ly/4dhbvMn
Hands-On with PicoScope 7: Pico Technologys Latest Oscilloscope Software - Workbench Wednesdays element14 presents 2024-07-24 | Bald Engineer dives into Pico Technology's latest PicoScope oscilloscopes software, PicoScope 7. Using a PicoScope 2000A (from the element14 Community) James walks through key measurements and demonstrations using the built-in arbitrary waveform generator. He explores new functionalities in PicoScope 7, such as the improved UI, a unique feature called DeepMeasure, and decoding I3C traffic. Read the full episode blog on the #element14community : bit.ly/4dhbvMn #0:00 Welcome to element14 presents#1:00 PicoScope Hardware#1:55 PicoScope Software#4:31 I2c versus I3C#7:17 Give your Feedback#PicoScope #USBOscilloscope #USBScope #PicoScope #testandmeasurement #T&M #oscilloscope Related articles:RoadTest Review of PicoScope 2000A: bit.ly/3LCQUGLWorkbench Wednesday- Bandwidth: bit.ly/4da0SuSWorkbench Wednesday- Trigger: bit.ly/3LEV2GhWorkbench Wednesday-NXP MCX Board: bit.ly/3LCx2n2Workbench Wednesday- Picking I2C Pull-Up Values: bit.ly/3Lze9BsEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Smart Subscriber Counter LED Sign with a Spectrum Analyzer element14 presents 2024-07-12 | In this video, Mark builds a smart custom logo to hang on the wall. It is connected to the internet and it will show the number of subscribers to his YouTube channel. It also has on board audio and a Spectrum Analyzer! Check out the full episode and episode blog on the #element14Community bit.ly/3S3UI7n #0:00 Welcome to element14 presents#0:52 Overview#2:44 The Electronics#6:56 Building The Sign#11:39 Programming It#15:26 Testing The Sign!#16:10 Give your FeedbackEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
How to Control a LEGO Mindstorms kit with AI and Raspberry Pi 5 element14 presents 2024-06-28 | In this video, Andy uses a Raspberry Pi 5 to enhance an unused LEGO robotics kit from the late 1990s. He also develops a modern, web-based graphical interface to replace the obsolete Windows 95 software it came with. Finally, he builds a trash-sorting robot and adds AI vision capabilities to his creation: bit.ly/4bpjzJG #0:00 Welcome to element14 presents#0:21 Overview#1:35 Wire Replacement#4:10 Testing With The Microcomputer#5:19 Uploading The Firmware#7:10 Making A Graphical Programming Tool#11:34 The Trash Robot!#13:53 Give your Feedback#raspberrypi #lego #legoproject #raspberrypi5 #robotics #ai #airobot Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
The Flux must flow! element14 presents 2024-06-21 | Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
DIY Jig for your Laser Cutter with Custom Arduino Automation element14 presents 2024-06-14 | Repetitive tasks are time thieves, and in the case of setting up machinery for a job, every change of workpiece can potentially bring the setup out of calibration. Clem needs to laser engrave multiple pieces in series and instead of reloading after every engraving cycle he automates the workpiece changing to process 4 workpieces at once. Utilizing the trusty arduino uno , tmc stepper drivers for smooth and precise movement Clem shows you how in principle you can automate every tedious process! What would you like to automate in your daily life? bit.ly/3RsysnH #0:00 Welcome to element14 presents#0:16 Overview#2:15 Designing It#4:33 Revolving Prototype#6:45 The Electronics#10:50 The Code#13:57 Problem Solving...#18:18 Let's Engrave!#19:01 Give your Feedback#lasercutter #automation #3dprinting #jigs #arduino Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
See what B&Ks DAS60 Handheld 6 Channel Recorder can Measure - Workbench Wednesdays element14 presents 2024-06-05 | James explores the features and functionalities of the versatile B&K Precision DAS60 data recorder. Overall, the B&K Precision DAS60 shines with its extensive input options, robust measurement capabilities, and remote accessibility. Whether in the lab or out in the field, this versatile tool is a must-have for any data logging application.Check out the blog on the #element14community : bit.ly/4592PVK #0:00 Welcome to element14 presents#0:35 DAS60 Overview#1:37 Sample Modes#3:21 Math And Functions#4:54 Using DAS60 Remotely#5:35 Give your Feedback#measurements #plotter #waveform #waveformrecorder #stripchart #dataanalytics #dataanalysis #engineeringtools Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
DIY Soldering Hot Plate element14 presents 2024-05-31 | Click, snap, done! :) Making a DIY Soldering Hot Plate in 35 seconds...Kind of! Watch the full project video here: youtu.be/pVeknb0dz6ARead the full project blog on the element14 Community: bit.ly/4dLrzHoEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
DIY Hot Plate for SMD Soldering Using Raspberry Pi Pico element14 presents 2024-05-24 | When you think of soldering, the first things that come to mind may be a soldering iron or a hot air gun for reflowing SMD components. Join Milos as he explores another method: using a hot plate!A hot plate can be bought cheaply. It's great for soldering with a PCB stencil or unsoldering an IC with many pins. This project shows how to create a DIY hot plate for soldering PCBs using a Raspberry Pi Pico for control and temperature regulation. The tutorial covers assembly, safety considerations, and integrating an NTC thermistor for temperature measurements. Viewers receive all necessary files and code, providing a cost-effective solution for precise PCB soldering.Read the full project blog on the element14 Community: bit.ly/4dLrzHoRead more on Characterising Thermistors here: bit.ly/4bRic7fCheck out Katie's project on "Mastering Oven Control: Precision Resin Curing with DIY Mods...How Hard Can it be??" bit.ly/3X1gBHI #0:00 Welcome to element14 presents#0:56 Overview#2:33 NTC Thermistor#6:09 The Enclosure#8:46 Schematic And Code#12:32 Assembly#14:00 The Final Product!#17:40 Give your Feedback#raspberrypi #3dprinting #raspberrypico #soldering #DIYhotplate #pcb #thermistor Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
How do BattleBots Work? In the Pit with HyperShock element14 presents 2024-05-17 | Explore the fascinating world of competitive robotics with a behind-the-scenes look at HyperShock. Join Team HyperShock as they showcase the technical expertise and ingenuity that make this fighting machine a force to be reckoned with at the Battlebots competition. James gets the opportunity to interview Will from Team HyperShock at the Battlebots competition in Las Vegas to delve into the technical intricacies of their formidable creation. HyperShock, weighing in at 250lb, is a fighting robot that commands attention with its bright yellow blur as it tears through opponents on the Battlebots stage. Find out more on the #element14community: bit.ly/3ygQQZJ #0:00 Welcome to element14 presents#0:27 Overview#3:00 The Motors#6:54 The Weapon#9:51 The Controller#13:23 Batteries And Testing#19:45 Give your Feedback#battlebots #hypershock #behindthescene Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Edge-lit 7-Segment Display Clock Using Raspberry Pi Pico element14 presents 2024-05-10 | In Episode 600 becon_dave on the community site commented that along with the cuckoo clock, a miniature 3D diorama scene could be added (like a traditional cuckoo clock), and suggested that a edge-lit multi-layered laser engraved scene could be used. So, in this episode of Element14 Presents, Katie introduces us to her latest project: creating an acrylic edge-lit clock.The inspiration stemmed from discussions in the community about edge-lit dioramas, sparking Katie's interest in utilizing a laser cutter for this endeavor. Beginning with a simple etched acrylic design, she outlines her vision for illuminating each number on the clock face. Katie experiments with edge-lit laser engraved acrylic by making a clock with a Raspberry Pi Pico, but ensure that it could be a platform that can be changed in the future, so maybe one day we’ll see a scene!Check out the full episode blog on the #element14Community: bit.ly/3JUlVVF#0:00 Welcome to element14 presents#0:18 Overview#1:18 The Plan#4:33 The Schematic And Design#10:22 Assembly#13:58 Time To Test!#15:27 Give your Feedback#homeautomation #raspberrypi #arduinoproject #smartroom #tutorial Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Smart Windows and Blinds with Arduino and Raspberry Pi Pico element14 presents 2024-05-03 | Have you ever wanted to be able to control things like lights or windows with a few clicks on your phone? Whether that is turning off the lights when you fall asleep with them on, or walking up in the middle of the night because it’s too hot and you want to open a window without getting up. In this video, Milos goes over some simple ways of automating things in your room using an Arduino and Raspberry Pi.Check out the full project blog on the #element14Community: #0:00 Welcome to element14 presents#0:30 Overview#1:05 MQTT#6:57 Venetian Blinds Actuator#10:41 Window Actuator#13:39 Main Node#18:10 Interface#21:45 Let's Test It!#22:58 Give your Feedback#3dprinting #raspberrypi #raspberrypico #automation #roomautomation #nodeserver #arduino #wifi #mqtt #iot #iotproject Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Hands-on with NXP’s MCX FRDM Boards - Workbench Wednesdays element14 presents 2024-05-01 | NXP's MCX Microcontrollers are their latest generation. They combine the best aspects of the previous LPC and Kinetis series products with a look to future applications. There are four processors in the family. In January 2024, they began shipping (in quantity) two of the microcontrollers along with development boards in the Freedom Platform, also known as FRDM.Discover NXP's MCX FRDM board in this detailed overview, highlighting the latest microcontroller and its development kit. Unveiling key features, programming options, and practical examples, it provides valuable insights for electronics enthusiasts. Read the full project blog on the #element14Community : bit.ly/4a3GqK6#0:00 Welcome to element14 presents#0:30 MCX Overview#1:46 Programming MCX#3:04 MCX Code Examples#5:09 Give your Feedback#microcontroller #microcontrollers #embeddedproject #machinelearning #realtimeclockEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Day 1 of electronics... element14 presents 2024-04-26 | Electronics is all about making connections...Plugs, Power, PCB's and most of all...People! #element14presents and the #element14community will give you the 'spark' you need to make the right 'connections'!Check out some of the element14presents episodes and blogs here: bit.ly/3WdtqOPEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Design for Manufacturing - Project to Product by Modifying Off-the-Shelf Cases element14 presents 2024-04-19 | When your project gets popular you might want to sell kits! Clem was asked to make a kit of his universal debugging screen and quickly realized how time consuming it would be to 3d print and assemble the project's parts! So instead of utilizing fully custom 3d prints he adopts a technique used in mass manufacturing! Clem redesigns his project to use an industrially made enclosure and modifies it to fit his needs, but instead of simply drilling a few holes in a project box, he leverages the data supplied by the manufacturer to devise a scalable process! Read the full episode blog on the #element14community : bit.ly/3vYvm37 #0:00 Welcome to element14 presents#0:32 Overview#1:24 Cases#2:37 Fitting It In The Case#5:35 Using CAD#9:20 Modifications#13:53 The Final Product#15:18 Give your Feedback#cncmachine #cncmilling #fiberlaser #manufacturingsolutions #productionprocess #enclosures #costeffectivesolutions #modification #casemodificationEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Using Nordics nRF7002, My Dehumidifier Tells Me When Its Full! element14 presents 2024-04-12 | Join James as he aims to create a Wi-Fi LED Detector using Nordic's nRF7002 Design Kit (DK), enabling appliances like James's lab dehumidifier to send internet notifications for maintenance. James’ initial challenges with custom PCBs led to a shift back to the DK board, successfully detecting the dehumidifier's status and assessing energy consumption. Despite the setbacks James experienced, the project showcases the potential of both the Nordic board and custom IoT notification devices!Check out the full episode blog on the element14 Community: bit.ly/3TYaJMB#0:00 Welcome to element14 presents#0:34 Overview#2:12 Xiao Means Little#3:40 Xiao plus EK#7:13 Wi-Fi LED Detector (DK Edition)#9:18 Wi-Fi Detector Demo#10:12 Custom nRF70 PCB Measurements#11:47 Give your Feedback#wifi #iot #mqtt #homeautomation #homeautomationprojects #nrf7002 #nef70Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Giant Retro Gaming Magic Mirror with a Raspberry Pi 5! element14 presents 2024-04-05 | Dave has long liked the idea of a Magic Mirror, but always wanted them to be a little more interactive. He also wanted to be able to to make the size a little bigger, like a full length mirror should be - maybe that would make it more accepting to other members of my house hold?David merges the concepts of a magic mirror and a retro arcade machine into a single, impressive 65-inch touch screen. Initially drawn to the potential of magic mirrors but craving more interactivity and size, David meticulously plans out the project's technical specifications. With a plethora of inputs and outputs, including RS 232 control, David ensures seamless communication between the Raspberry Pi and the screen, optimizing functionality while managing power consumption! Check out the full video blog on the element14 Community: bit.ly/3TOP2yt#0:00 Welcome to element14 presents#1:00 Overview#2:11 Raspberry Pi#6:53 The Electronics#8:51 Putting It All Together#10:29 Turning It On#13:17 Give your Feedback#magicmirror #raspberrypi #raspberrypiprojects #emulationstation #recalbox #PINN #touchscreen #dualboot Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Home AI Image Generation Server with LattePanda and Stable Diffusion element14 presents 2024-03-29 | It's fun playing with AI image generators, but remember the cloud is just someone else's computer! Clem recently wrecked his editing pcs with a bit too demanding generative tasks, so he decides to build a dedicated AI image generation server for stable diffusion on a minimal budget. He utilizes LattePanda Single board Computers and used graphics cards to build a capable but very affordable AI server. Its all about focusing hardware and software on the task to get the most bang for your buck!#0:00 Welcome to element14 presents#0:20 Overview#1:13 Hardware#3:51 Clem On The Case#5:17 Booting Up!#7:04 Operating System#8:00 Running AI#12:41 LattePanda Alpha#14:08 Give your Feedback#stablediffusion #easydiffusion #comfyui #sbc #lattepanda #AI #ai #aiserver #homemadeAIEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Mount 3d Printed Parts to a Flat Surface element14 presents 2024-03-25 | Want to know a quick trick to mount 3D Printed part to a flat service? We've got you covered!Check out the full episode here: bit.ly/3vpzZD6Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Building an Open-Source Tool for Cave Surveying element14 presents 2024-03-22 | Phil spent years groveling in mud trying to map caves. He shows you how he found a better way, using open source software and electronics!Join Phil, an avid caver, as he recounts his journey of creating a cutting-edge cave surveying tool. Reflecting on his experiences in the 1990s, where primitive equipment like mechanical compasses and cumbersome tape measures hindered exploration efforts, Phil recognized the need for a more effective solution!Check out the full episode blog on the element14 Community: bit.ly/3PwDminEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#caving #circuitpython #Magnetometer #accelerometer #speleology #nrf52840 #laser #xiao #mapping #surveying #CaveMappingTech #SpelunkingInnovation #undergroundexploration
Netgear JGS516PE and PoE Kit Teardown - The Electronics Inside element14 presents 2024-03-20 | PoE (Power over Ethernet) is a very common technology, but its use is typically limited to corporate networks. What makes it tick, and moreover, could we make more use of it as makers? Join us as we teardown a Netgear JGS516PE and explore other PoE equipment such as a camera that supports power over ethernet. Check out the full episode blog on the element14 Community: bit.ly/3PsRLw0#0:00 The Electronics Inside#0:29 Power Over Ethernet#8:00 Prepping To Wire It#20:12 Give your FeedbackEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#poe #netgear #PowerOverEthernet
It doesnt have a GPU? element14 presents 2024-03-20 | If it doesn't have a GPU, then Clem just has to give it one! Want to see how he did it? Check out the full episode blog here: bit.ly/3viMSP9Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Creating a Digital Roulette Table with an ESP32 DevKit element14 presents 2024-03-15 | In this video Mark shows you how to build a digital roulette game that you can use for you family game night. It uses a ESP32 and some pixel LEDs and it comes with some nice Arduino programming! Check out the full video blog on the element14 Community: bit.ly/49PLYbW#0:00 Welcome to element14 presents#0:35 Overview#2:33 The Electronics#4:19 Putting It Together#8:53 The Code#12:55 Let's Play!#13:36 Give your FeedbackEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Whats wrong with this circuit? element14 presents 2024-03-13 | Can you spot what's wrong with this circuit? Watch the full episode on the element14 Community: bit.ly/4cdgMF4Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Will this Step Up Converter Work? element14 presents 2024-03-12 | This was the most difficult project Clem ever attempted. . .See how it went: youtu.be/1BFW84GAe1g
Practical DIY Pi Pico Current Load Circuits element14 presents 2024-03-08 | For whatever electronics projects you’re doing, one thing is for sure, you need to power it somehow. It can be anything from being directly connected to the outlet, a battery, a buck converter, a linear regulator and so on. When you think about testing a power supply, the first thing you think about is measuring its output voltage. Another important thing that should be tested is how that power supply performs under a load, whether that’s a battery or a buck converter. In this video, Milos will show us a few different ways of achieving this! Check out the full episode blog on the element14 Community: bit.ly/3Tth7Ms#0:00 Welcome to element14 presents#0:54 Overview#2:56 Making It Digital#8:15 The Schematic#9:34 The Code#11:41 The Case#15:22 Let's Test It!#19:00 Give your FeedbackEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJYKeywords: 3D Printing, Raspberry Pi, Raspberry Pico W, Adjustable Load, DIY, Test Equipment, DIY Test Equipment, Current Load, Constant Current, DFROBOT, LCD, Op-Amp, Operational Amplifier, MOSFET, Power Latch Circuit, Constant Current Load, Battery Capacity Tester, DIY Battery Capacity Tester
If and When Do I2C Pull-Up Values Matter? - Workbench Wednesdays element14 presents 2024-03-06 | Unravel the mystery behind picking I2C pull-up resistor values! Discover why certain values work, the rise time calculations, and how to find I2C bus capacitance. Bald Engineer James guides you through selecting the correct resistor. James shows examples of resistors that are too big (Arduino internal pull-ups) and the correct value. Take advantage of these tips on ensuring compliance with the I2C spec. Ready to become a pull-up resistor pro? Check out the full episode blog on the element14 Community here: bit.ly/3wGkcjFEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware:Tech spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY
Turning a Raspberry Pi Pico into a GPU! element14 presents 2024-03-01 | Everything can become a GPU if you're weird enough, right!? Clem surely has the weirdness required here, as he attempts to take a Raspberry Pi Pico and turn it into a DVI graphics card for use with single board computers, microcontrollers, and especially his Sudosom module that runs Linux on an ESP32S3.His project is an iteration on the amazing work of the Pico-DVI project by Luke Wren (link below), and Clem aims for compatibility with the popular Adafruit graphics library commands.Discuss the episode, find all files, and ask Clem questions on the element14 Community! bit.ly/3wsLbyPPico dvi github.com/Wren6991/PicoDVIDVI Sock github.com/Wren6991/Pico-DVI-SockEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:19 Overview#2:17 Pico DVI#5:09 But Is It a GPU?#10:06 Code and Test#12:24 Last Minute PCB!#14:46 What's Next?#15:33 Give Your Feedback#raspberrypi #raspberrypiprojects #raspberrypipico #raspberrypiprojectcenters #gpu #linux
Making a Tribble that Detects Klingons element14 presents 2024-02-23 | In the 1960s, fluffy aliens called "Tribbles" found their way onto the original Star Trek series. Characters from the show knew if the Tribbles liked or disliked them by the sounds they made. Andy has a stuffed tribble toy, but it's silent and motionless.In this episode, Andy builds a new tribble that can react to your presence. Just know that if you're an undercover Klingon, the ear-piercing Tribble screeches will give you away!Discuss the episode and ask Andy questions on the element14 Community! bit.ly/3TbEZEAEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:42 Overview#1:22 Parts Review#2:26 Building the Circuit#3:49 Writing the Software#9:44 Refining the Circuit#11:48 The Final Build#12:41 3D Printing an Enclosure#13:36 Sewing the Thing#14:26 Fun with Tribbles#15:13 Give Your Feedback#raspberrypi #raspberrypiprojects #raspberrypipico #raspberrypiprojectcenters #tribble #tribbles #startrek #startrektos #startrektheoriginalseries #klingon #klingons
3D Printer Time-Lapse Camera with a Raspberry Pi 5 element14 presents 2024-02-16 | Katie had a camera set up to capture time lapse footage of her 3D printer as it worked, but that camera had an unfortunate mishap involving a saltwater pool!Rather than buying a replacement for the original camera she used, Katie builds her own version with a Raspberry Pi 5 and the Pi High-Quality Camera. The new build replaces the functionality of the old camera and adds new features that make it even more useful.Discuss the episode and ask Katie questions on the element14 Community! bit.ly/42GRlHKEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:19 Overview#3:49 The Plan#5:46 Testing the Code#11:02 Case Design#16:08 Time Lapse Time!#16:52 Give Your Feedback#raspberrypi #raspberrypiprojects #raspberrypi5 #timelapse #timelapsecamera #actioncamera #3dprinting #3dprinter #3dprinters #raspberrypiprojectcenters
Sony WENA 3 Smart Watch Teardown - The Electronics Inside element14 presents 2024-02-14 | Sony tried getting into smart watches globally back in 2015, but they quickly withdrew from the market. However, they do still make a line of wearable devices, but only for the Japanese market.In this episode, David gets his hands on a Sony WENA 3 smart watch, takes it apart to see what's going on inside, and comes away thoroughly impressed with Sony's work.Discuss the episode and ask David questions on the element14 Community! bit.ly/3HVMQiWEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 The Electronics Inside#0:22 Sony WENA#2:14 The Teardown#11:49 Give Your Feedback#smartwatch #smartwatches #wearabledevices #wearabletech #sony #watches #fitnesstracker #fitnesstrackers #teardown
Moon Phase Display with Raspberry Pi Pico element14 presents 2024-02-09 | Follow along with Lorraine as she creates a desktop lunar phase display! The project involves integrating a keypad and LED displays to visually represent the moon's phases based on user-input dates, as well as some coding in Python to retrieve information via the Astronomy API. Lorraine addresses the coding challenges and hardware implementation, showcasing a successful and functional moon phase display.Discuss the episode, find all supporting files, and ask Lorraine questions on the element14 community! bit.ly/3SxZl9hEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:17 Overview#1:44 Let's Go Shopping#2:46 A Moon API#9:03 Wiring Up the LED Displays#10:39 Building a Moon#18:11 The Moon Phases!#19:07 Give Your Feedback#moonphase #moonphases #raspberrypi #raspberrypiprojects #raspberrypipico #moonwatch #kitronik
Tinkering vs Engineering: Can You Build a Laptop from Scratch? element14 presents 2024-02-02 | Clem's latest project takes a deep dive into laptop design, merging various components that he's previously built, such as a BLE keyboard, compute module, mouse, and a universal diagnostic screen into a custom-built laptop. However, the path to success isn't without its challenges (major challenges).To overcome the steep learning curve of power supply design, he has to design his first ever step-up converter and find a way to put multiple converters in parallel. Charging and protecting multiple cells is a challenge in itself, but Clem has a plan. Will this project break him?Discuss the episode and ask Clem questions on the element14 Community! bit.ly/49iYss8Engage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:18 Overview#2:30 The Charging Circuit#5:44 Testing the Charging Circuit#9:48 Step-Up Converter#13:25 Putting It All Together#16:12 What's Next?#20:13 Give Your Feedback#powersupply #powersupplies #laptop #charging #chargingsolution #chargingsolutions
Hands-on with Nordic’s nRF7002 DK, EK, and EB Boards - Workbench Wednesdays element14 presents 2024-01-31 | Nordic Semiconductor's first Wi-Fi capable chip was the nRF7002. This companion IC adds Wi-Fi 6 at 2.4 GHz and 5 GHz to any microcontroller with an SPI or QSPI interface. The nRF7002 DK (development kit) provides a demonstration platform for the chip and Nordic's nRF53 Arm + Bluetooth Low Energy SoC.In this video, James gives an overview of the nRF7002 and its design kit. Then, he demonstrates some current and RF measurements. Last, he compares the nRF7002 to the DK, EK, and EB.Discuss the episode, find resources, and ask James questions on the element14 Community! bit.ly/499tBOqEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to Workbench Wednesdays#0:44 nRF70 Introduction#2:00 nRF7002 DK Overview#3:08 Wi-Fi Shell Example#5:19 Current Consumption#6:16 RF Measurements#7:38 DK vs EK vs EB#9:23 Give Your Feedback#wifi #wifi6 #bluetooth #microcontroller #microcontrollers
Off-Grid Remote Generator Starter element14 presents 2024-01-26 | When Kaleb needs to run the generator at Bonesnapper Ridge, his off-grid living space and maker shop, it usually means that it's raining, snowing, and generally muddy. The walk from the house to the generator in those conditions is doable, but not his favorite activity. There could be many solutions to this problem, but for Kaleb, he wants a custom solution that fits his exact needs!In this episode, he builds a remote generator starter for a Honda EU-7000is generator. The build will have control via Wi-Fi, a custom-made panel with displays, and will be powered by an Arduino Nano.Discuss the episode and ask Kaleb questions on the element14 Community! bit.ly/3ucViacEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:31 Overview#1:40 The Electronics#5:40 The Code#8:14 Assembly#10:22 No More Walking!#12:19 Give Your Feedback#arduino #arduinoproject #arduinoprojects #arduinonano #generator #generators #offgrid #offgridliving #offgridlife #offgridlifestyle
All 100 Pins on the First Try! element14 presents 2024-01-24 | So Satisfying. . . stay tuned - the full episode goes live the first Friday of February!
Custom RP2040 PCB: Design, Turn-On, and Debug - How Hard Could It Be? element14 presents 2024-01-19 | James originally intended to make a video about a tool that he calls a "State Mode Logic Analyzer." One of the core components of that project is the RP2040 microcontroller from Raspberry Pi and its programmable IO (PIO) modules.However, getting the RP2040s to work on the custom-made PCBs that James designed turned out to be a chore. So, for this episode, he shares soldering RP2040 (QFN) techniques, easy-to-solder parts for RP2040 designs, and what to debug when turning on custom microcontroller boards. After all, how hard could it be to make a custom RP2040 PCB?Discuss the episode, questions James's design choices, and ask him questions on the element14 Community! bit.ly/3HqKMz6Article: The Myth of Three Capacitor Values - bit.ly/3SoXtRxWorkbench Wednesdays - Why You Need a Raspberry Pi Pico Development Board by Shabaz: bit.ly/47B4R0sEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:36 Overview#2:41 Power and Decoupling#3:56 Program and Debugger#5:02 Boot and Reset Buttons#6:17 Turn-On#12:06 Give Your Feedback#raspberrypi #raspberrypiprojects #pcbdesign #pcbdesigning #debugger #debugging #rp2040 #raspberrypipico #microcontroller #microcontrollers
Clems Massive Hoarding Problem: The Computer element14 presents 2024-01-18 | Sometimes the only question for Clem and his massive hoarding problem is. . . why?He's blogging about his hoarding issues on the element14 Community bit.ly/3tXDhg0
Exploring the Intricacies of Strain Gauges in Mechanical Systems - DC To Daylight element14 presents 2024-01-17 | In this DC to Daylight episode, Derek shows how strain gauges are used to measure strain in a system as it relates to stress. He explains the basics of how strain gauges are constructed, the proper orientation of them during application, as well has how they are applied to a mechanical structure in order to measure a material's deformation (a.k.a strain). In addition, he goes through a few methods of attaching one or more strain gauges to a Wheatstone bridge in order to extract a miniscule voltage from the strain gauges as they work.Discuss the episode and ask Derek questions on the element14 Community! bit.ly/3Hs17DDHow a Wheatstone Bridge works: bit.ly/3ZWYjXJEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to DC To Daylight#0:36 Strain Gauges#7:00 Attaching It#13:33 Measure#15:31 Give Your Feedback#sensor #sensors #wheatstone_bridge #wheatstone
Making Music with a Lego Guitar and Capacitive Touch element14 presents 2024-01-12 | Katie's son challenged her to make his Lego electric guitar model interactive and able to play music, so in this episode she works with him on the project! They add capacitive touch pads to the neck of the guitar and allow it to play actual guitar sounds through a Lego model amplifier (with a hidden amplifier and speaker).Discuss the episode and ask Katie questions on the element14 Community! bit.ly/3TYogp2Engage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#1:02 Overview#1:43 The Code#3:50 A Quick Test#6:53 Prepping to Wire It#10:08 Wiring & Finishing Touches!#11:39 Give Your Feedback#raspberrypi #raspberrypiprojects #lego #legoproject #raspberrypi3
Creating an IMU-based 3D Mouse with an ESP32-S3 element14 presents 2024-01-05 | Why is nobody making a mouse with a motion sensor!? All the mice Clem could find online use optical sensors, so he asks the question: why not use an IMU (inertial measurement unit) as a way to track the movement of a mouse in space?Armed with a PCB he made in KiCad and great ambitions, he soon encounters the truth: it's really hard! The math is challenging, and the outcome would barely be usable, but Clem also learns that building a 3D air mouse this way would be quite easy.Find all project files and ask Clem questions on the element14 Community! bit.ly/3vouqV2Engage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:21 Overview#2:04 The PCB#5:09 Assembly#7:18 The ... Code?#10:53 New Mouse and Code!#13:33 Putting the Mouse to Use!#14:49 Give Your Feedback#computermouse #esp32 #esp32project #kicad #pcbdesign #pcbdesigning
Should Clem Make a Mouse? element14 presents 2024-01-03 | Clem loves his mouse. Question: Can he recreate it in open source with easily sourced parts?Answer: studio.youtube.com/video/JaCi-V2e2kA
Apple Watch Series 3 Teardown - The Electronics Inside element14 presents 2024-01-03 | After a kind donation to The Electronics Inside, David got his hands on an Apple Watch Series 3 for a teardown! It's especially useful, because he finally has some kind of basis for comparison for the Garmin Fenix 7 Solar watch that he previously opened up. So, how does Apple approach the design of a smart watch as compared to Garmin?Discuss the episode and ask David questions on the element14 Community! bit.ly/3TQFG6ZCheck out the teardown of the Garmin Fēnix 7S fitness watch: bit.ly/3x7r9I1Engage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 The Electronics Inside#0:14 Apple Watch Series 3#13:30 Give Your Feedback#teardown #applewatch #applewatchseries3 #applewatches #smartwatch #smartwatches #wearabledevices #wearabletech #wearabletechnology
Vintage Electronics Exploration with a Bally Cypress Gardens Bingo Machine element14 presents 2023-12-29 | In this episode, follow along as Ruby explores a Bally Bingo electromechanical gaming machine from 1958, affectionately nicknamed Ms. Creaky! Ruby jumps right in, troubleshooting the machine, exploring historical components, and navigating the challenges of electromechanical restoration.Discuss the episode and ask Ruby questions on the element14 Community! bit.ly/3GZS3G1Engage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:43 Overview#3:58 Fixing Up Miss Creaky#11:08 Brainstorming Modernization#14:01 Playing Miss Creaky!#16:57 Give Your Feedback#vintageelectronics #vintagetech #electromechanical #pinball #pinballmachine
Craft a Festive LED Christmas Sweater Featuring the ATtiny416! element14 presents 2023-12-22 | Join Mark Harris on his DIY journey as he blends festive fun with electronics, showing you step-by-step how to create a dazzling LED Christmas sweater! Imagine an ugly Christmas sweater decked out with custom LED boards, powered by the Microchip ATtiny416, an affordable microcontroller with multiple PWM outputs for creative lighting effects.Discuss the episode, find all supporting files, and ask Mark questions on the element14 Community! bit.ly/4auUfmoEngage with the element14 presents team on the element14 Community - suggest builds, find project files, and see behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to element14 presents#0:24 Overview#2:07 The Boards#4:31 The Code#5:41 Assembling the Sweater#8:00 Lighting the Sweater!#9:01 Give Your Feedback#wearabledevices #wearabletech #wearabletechnology #attiny85 #microchip #uglychristmassweaters #uglychristmassweater #visualstudio #visualstudiocode #microcontroller #microcontrollers
Overview of the Keysight Battery Emulator (E36731A and BV9211B) - Workbench Wednesdays element14 presents 2023-12-20 | Keyight's E36731A hardware and BV9211B software combine to make a complete battery test and emulation solution. On this Workbench Wednesdays episode, James demonstrates that you can use these tools to profile how a battery charges and discharges, and then use those profiles to emulate batteries in an actual circuit.Discuss the episode and ask James questions on the element14 Community! bit.ly/4aq5JYqFind RoadTest reviews for this device on the community: bit.ly/48mXs5CEngage with the element14 presents team on the element14 Community - suggest builds, find project files and behind the scenes video: bit.ly/3tmdewvVisit the element14 Community for more great activities and free hardware: bit.ly/3q6YMpuTech Spotlights: bit.ly/3qPrDhMRoadTest and Reviews: bit.ly/3pV5BuxProject14: bit.ly/31wbnJY#0:00 Welcome to Workbench Wednesdays#0:50 E36731 Overview#2:49 Power Supply and Load Functions#4:05 Battery Test and Emulation Software#6:34 Battery Discharge Profile#9:17 A Few More Things...#10:07 Give Your Feedback#keysight #batteries #powersupply #powersupplies #testequipment
Christmas Spy Ornament element14 presents 2023-12-19 | Check out the project video: youtube.com/watch?v=UnwMHgpKqw4
