OddVikingFilling 3D prints to remove the filament lines is essential to creating finished props. In this tutorial I talk about the process generally, and then show my favorite method using Bondo Glazing and Spot Putty thinned with acetone to rapidly apply fast-drying coats. I then sand the filler smooth, and move to using a final pass of Filler Primer, that gets wet-sanded smooth. A final coat of primer reveals the smooth surface, ready for paint.
Important: Acetone melts ABS, so this will not work with ABS prints without likely destroying the print below. The prints in this video are all PLA.
Finishing 3D prints - Filling and sanding print lines for propsOddViking2024-05-22 | Filling 3D prints to remove the filament lines is essential to creating finished props. In this tutorial I talk about the process generally, and then show my favorite method using Bondo Glazing and Spot Putty thinned with acetone to rapidly apply fast-drying coats. I then sand the filler smooth, and move to using a final pass of Filler Primer, that gets wet-sanded smooth. A final coat of primer reveals the smooth surface, ready for paint.
Important: Acetone melts ABS, so this will not work with ABS prints without likely destroying the print below. The prints in this video are all PLA.
Follow more of my builds where I post them as I am doing them: Instagram: instagram.com/oddvikingProp Weathering 5: Alcohol-based Ink SpecklingOddViking2023-06-11 | This weathering technique adds another layer of texture to your props, tiny speckled rings of color. This uses Copic Ink refills, an alcohol-based ink that is diluted in more alcohol, airbrushed on, and then speckled using a spray bottle filled with 70% isopropyl alcohol. I show some real-world examples of this texture, discuss the technique and uses, and show some real-time footage of how I used it on some custom Mandalorian style armor. I filmed this as I painted props over a few months, so I do repeat things a bit as I narrate. But I got it all in there! Comment if you have used this technique and discovered something I didn’t, or have anything else to share!
Copic Ink Refill colors: Use any that you like, the ones used in this video were: N5-Neutral Gray 5, E79-CASHEW, and E34-TOAST
Follow more of my builds where I post them as I am doing them: Instagram: instagram.com/oddvikingMando gauntlet computer screensOddViking2023-04-29 | These are my two custom OLED screen animations for my post-imperial custom Mandalorian cosplay build. I created the animations as a series of png files, and Jettisonable on Etsy programmed them in and set up the components.
See my full build thread at mandalorianmercs.org/forum/index.php?topic=228800.0Boot-Tab popping out: fixOddViking2023-04-29 | I came across an issue while building my custom Mandalorian cosplay. When my heel went back far enough, the boot tab would pop out and prevent the shin armor from resetting. I came up with this simple solution.
The rectangular “ring” had a side seam that I cut wider with a Dremel, but a solid rectangular ring will work the same.
The leather part is from some antique military riding gaiters, usually dated as WWI or WWII and they arr many on eBay. The shin armor is adapted Bo Katan shins. For more on my build, see my WIP posts on Instagram (same user name), or my build thread here:
IG: instagram.com/oddvikingCustomizing Costume Containers - Part 4 of 4OddViking2022-08-07 | I customize my containers for each Star Wars costume I build, so that they look more like something from that universe. This tutorial teaches a lot of tips and tricks I have discovered over the years, as well as some pitfalls to avoid, and some simple fixes for when paint issues arise. People have asked for a tutorial on these, and I put this together over a few months. It was an hour and 45 minutes long, so I broke it up into four parts. This video is part 1.
Part 1: Introduction, example cases, choosing your case. Video link: youtu.be/0zM2-WyhEh4
Part 2: Paint preparation, laying out greeblies and decals, and how to more permanently mount them. Video link: youtu.be/lqNhbvtmBrE
Part 3: Priming, painting, troubleshooting, and weathering. Video link: youtu.be/F8FjhUvFRVQ
Part 4: Adding electronics, simple switch installed in a battery night light, basic circuits.
About me: I am an enthusiastic ameteur prop builder, focused on Star Wars props. I am a member of both the Rebel Legion and 501s Legion costuming clubs in the San Francisco Bay Area in California. I post a lot of my builds and other costume content on my Instagram with the same username. https://www.instagram.com/oddviking
For some of these videos, I was getting over a cold, so there is come congestion sound to my voice (apologies!).
basic LED resistor calculator: http://www.hebeiltd.com.cn/?p=zz.led.resistor.calculatorCustomizing Costume Containers - Part 3 of 4OddViking2022-08-07 | I customize my containers for each Star Wars costume I build, so that they look more like something from that universe. This tutorial teaches a lot of tips and tricks I have discovered over the years, as well as some pitfalls to avoid, and some simple fixes for when paint issues arise. People have asked for a tutorial on these, and I put this together over a few months. It was an hour and 45 minutes long, so I broke it up into four parts. This video is part 1.
Part 1: Introduction, example cases, choosing your case. Video link: youtu.be/0zM2-WyhEh4
Part 2: Paint preparation, laying out greeblies and decals, and how to more permanently mount them. Video link: youtu.be/lqNhbvtmBrE
Part 3: Priming, painting, troubleshooting, and weathering.
Part 4: Adding electronics, simple switch installed in a battery night light, basic circuits. Video link: youtu.be/hMvM6bDgu3c
About me: I am an enthusiastic ameteur prop builder, focused on Star Wars props. I am a member of both the Rebel Legion and 501s Legion costuming clubs in the San Francisco Bay Area in California. I post a lot of my builds and other costume content on my Instagram with the same username. https://www.instagram.com/oddviking
For some of these videos, I was getting over a cold, so there is come congestion sound to my voice (apologies!).
basic LED resistor calculator: http://www.hebeiltd.com.cn/?p=zz.led.resistor.calculatorCustomizing Costume Containers - Part 2 of 4OddViking2022-08-07 | I customize my containers for each Star Wars costume I build, so that they look more like something from that universe. This tutorial teaches a lot of tips and tricks I have discovered over the years, as well as some pitfalls to avoid, and some simple fixes for when paint issues arise. People have asked for a tutorial on these, and I put this together over a few months. It was an hour and 45 minutes long, so I broke it up into four parts. This video is part 1.
Part 1: Introduction, example cases, choosing your case. Video link: youtu.be/0zM2-WyhEh4
Part 2: Paint preparation, laying out greeblies and decals, and how to more permanently mount them.
Part 3: Priming, painting, troubleshooting, and weathering. Video link: youtu.be/F8FjhUvFRVQ
Part 4: Adding electronics, simple switch installed in a battery night light, basic circuits. Video link: youtu.be/hMvM6bDgu3c
About me: I am an enthusiastic ameteur prop builder, focused on Star Wars props. I am a member of both the Rebel Legion and 501s Legion costuming clubs in the San Francisco Bay Area in California. I post a lot of my builds and other costume content on my Instagram with the same username. https://www.instagram.com/oddviking
For some of these videos, I was getting over a cold, so there is come congestion sound to my voice (apologies!).
basic LED resistor calculator: http://www.hebeiltd.com.cn/?p=zz.led.resistor.calculatorCustomizing Costume Containers - Part 1 of 4OddViking2022-08-07 | I customize my containers for each Star Wars costume I build, so that they look more like something from that universe. This tutorial teaches a lot of tips and tricks I have discovered over the years, as well as some pitfalls to avoid, and some simple fixes for when paint issues arise. People have asked for a tutorial on these, and I put this together over a few months. It was an hour and 45 minutes long, so I broke it up into four parts. This video is part 1.
Part 1: Introduction, example cases, choosing your case.
Part 2: Paint preparation, laying out greeblies and decals, and how to more permanently mount them. Video link: youtu.be/lqNhbvtmBrE
Part 3: Priming, painting, troubleshooting, and weathering. Video link: youtu.be/F8FjhUvFRVQ
Part 4: Adding electronics, simple switch installed in a battery night light, basic circuits. Video link: youtu.be/hMvM6bDgu3c
About me: I am an enthusiastic ameteur prop builder, focused on Star Wars props. I am a member of both the Rebel Legion and 501s Legion costuming clubs in the San Francisco Bay Area in California. I post a lot of my builds and other costume content on my Instagram with the same username. https://www.instagram.com/oddviking
For some of these videos, I was getting over a cold, so there is come congestion sound to my voice (apologies!).
basic LED resistor calculator: http://www.hebeiltd.com.cn/?p=zz.led.resistor.calculatorWhat we can do about negative costumer interactions with the 501st & Rebel Legions.OddViking2022-07-11 | I keep seeing posts in general Star Wars Cosplay groups about similar bad interactions with Legion Members about their costumes, and it sours their view of the Legion costume clubs. The "Bad Apples" really taint our reputation, and we can do better by lifting up fellow Star Wars costumers rather than give unsolicited costume advice. I made this for my Garrison's upcoming training session (Golden Gate Garrison in Northern California), but it applies as a good way to interact with costumers, no matter your Legion or group.Prop Weathering Tutorial - Part 4: Fullers Earth (dust) WeatheringOddViking2022-04-08 | Weathering armor and other hard props is my favorite part of the build. In this fourth part of the tutorial, I delve into Fuller's Earth, a powder used for all sorts of things, including weathering in the movie industry. Many will just dust it on, which works, but I show a technique I came up with for a more controlled, longer-lasting process that involves a paintbrush or airbrush applying a binder to stick the dust down.
*UPDATE* Since this video, I have only been using the paintbrush to apply the matte varnish, I no longer use an airbrush. The both work, but the airbrush has a little less control, and requires more cleaning after use. The brush method I switched to in this video is now my standard technique.
I build armored costumes and props for Star Wars costumes as a member of the 501st Legion and Rebel Legion. In this build I show some props that I have weathered this way, and I weather a small prop start to finish.
"SE-14R Blaster" .stl files: etsy.com/listing/911192074/spacebobs-se14-r-and-thermal-detonatorClone Trooper Electrobinoculars internal lit view screen solutionOddViking2022-02-18 | ...Clone Trooper Electrobinoculars prop (with lights)OddViking2022-02-18 | ...Prop Weathering Tutorial - Part 3: Chipped Paint WeatheringOddViking2021-09-04 | Weathering armor and other hard props is my favorite part of the build. In this third part of the tutorial, I compare three different methods of producing a chipped paint look, on both metallic and white surfaces (like Mandalorian and Clone armor). I mask using yellow mustard, toothpaste, and latex masking fluid, and then compare and contrast the advantages and disadvantages of all three (and learn a thing or two along the way).
I build armored costumes and props for Star Wars costumes as a member of the 501st Legion and Rebel Legion. In this build I paint a scrap with two surfaces in order to test on those types of paints, but this process will work with any armor or other hard props.
Helmets featured were finished and painted by me: Endor Trooper 3D printed kit by StarBreather, Clone Trooper helmet resin cast kit by EVO3, and Bo Katan 3D printed kit by Galactic Armory
501st Legion Clone Trooper Detachment Forums: 501stclonetroopers.com/forumProp Weathering Tutorial - Part 2: Acrylic Wash WeatheringOddViking2021-07-14 | Weathering armor and other hard props is my favorite part of the build. In this second part of the tutorial, I demonstrate on some ABS armor pieces how I prepare the armor with some "physical weathering" to roughen and gouge the props to prepare it for acrylic washes. Then I paint acrylic washes in various ways to give the armor realistic looking grime and wear. I build armored costumes and props for Star Wars costumes as a member of the 501st Legion and Rebel Legion. In this build I am working on some Movie Realistic Clone Trooper armor pieces, but this process will work with any armor or other hard props.
501st Legion Clone Trooper Detachment Forums: 501stclonetroopers.com/forumProp Weathering Tutorial - Part 1: Weathering TheoryOddViking2021-07-14 | Weathering armor and other hard props is my favorite part of the build. In this first part of the tutorial, I go over the theory and thought that goes into weathering objects. Even if you weather using a different technique than I do, the planning and intention behind weathering will make your props look much more realistic. I build armored costumes and props for Star Wars costumes as a member of the 501st Legion and Rebel Legion. In this build I am working on some Movie Realistic Clone Trooper armor pieces, but other props and examples are also shown.
501st Legion Clone Trooper Detachment Forums: 501stclonetroopers.com/forumTroubleshooting Cracks In Clone Trooper Armor SeamsOddViking2021-06-25 | If you are building Clone Trooper armor from a hard ABS kit, and some of your seams are cracking, this technique may solve your cracking problem. I also go into making and using ABS sludge, and how to apply it, but the primary cracking issue can be solved with most fillers or epoxy putties.
I often post build pics and photo edits on my Instagram: instagram.com/oddvikingEpIIIcloneHelmet FaceOff turnaroundOddViking2021-05-07 | This is showing the new Imperial Surplus Clone Helmet (Episode III - Movie Realistic version) that I completed with the "face-off" mod. Turnaround to show the "face-off" piece separated. More on this build on the 501st Clone Trooper Detachment and Instagram, username OddViking on both platforms.EpIIIcloneHelmet turnaroundOddViking2021-05-07 | This is showing the new Imperial Surplus Clone Helmet (Episode III - Movie Realistic version) that I completed with the "face-off" mod. Turnaround to show the weathering. More on this build on the 501st Clone Trooper Detachment and Instagram, username OddViking on both platforms.EpIIIcloneHelmet FaceOff DescriptionOddViking2021-05-07 | This is showing the new Imperial Surplus Clone Helmet (Episode III - Movie Realistic version) that I completed with the "face-off" mod. I describe why that is necessary for this accurate helmet type. More on this build on the 501st Clone Trooper Detachment and Instagram, username OddViking on both platforms.Endor Proton Grenade propOddViking2021-03-09 | This is my completed Return of the Jedi “Proton Grenade” (sometimes referred to as a “Bunker Buster”) from a kit by Van Oaks Props. I added a twist switch with a ratchet and lights, magnets, and original Photomultiplier tube dynodes.
Build thread here: therpf.com/forums/threads/return-of-the-jedi-proton-grenade-bunker-buster-prop.337921/#post-5176016Electronics installed in my Star Wars Stormtrooper helmet caseOddViking2020-12-12 | Progress on the lights and little display screen installed in my Star Wars Stormtrooper helmet case. Screen by Jettisonable on Etsy (custom Aurebesh message).Thermal detonator prop with lights and soundOddViking2020-04-09 | I built a couple years ago, from a 3-D print and then followed instructions on Instructables on how to put in the lights and sound. Pretty difficult to fit it in there, but I love it once it was all built.DC-15s Clone Trooper Blaster prop with lightOddViking2019-10-01 | I used a 3D printed DC-15s Clone Trooper Blaster Kit (Imperial Arms 3D), modified to accept wiring a blue bulb to the trigger and battery pack in the magazine, as well as to swap the printed bolts and front sights with real metal ones.
Build thread on the 501st Clone Trooper forums has more details on what I did: 501stclonetroopers.com/forum/index.php?/topic/26478-realistic-dc-15s-3d-printed-mod-with-blue-lightClone Trooper back plate cooling systemOddViking2019-09-04 | I came up with the cooling system for my back plate of my Phase Two Clone Trooper armor (KW kit). It has two fans and a 9 V battery [UPDATE: the 9V doesn't last long, and I changed this out for three AA batteries, and the fans stay humming for hours now], and sucks in the air from inside the armor and vents out through the four holes (mesh covered) on the back plate.Clone Commander Audio System in a Clone Trooper HelmetOddViking2019-05-10 | This is a test of my clone commander audio system by Ukswrath that I installed inside my Phase Two clone trooper helmet (kit by Evo3, assembly and paint by me).
I am not affiliated with Ukswrath, but here are where you can buy his system (he makes ones for other types of helmets too, I have his in my stormtrooper helmet as well):