JMSpeedshop !
Injector size calculation HOW TO size fuel injector flow rate. 10 . JMSpeedshop !
updated
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Hydraulic system done !! S124 V8 turbo ready to go on it's wheels
The system was already al connected seperate front and rear system. I Was waiting the last months on the flow divider. This will give me 2 seperate systems from 1 oil pump flow. This is needed because the system is also pumping pressure less over the return when the level does not need to be raised. When this is needed in the front on the rear seperate, It needs to be possible to create pressure on 1 side . without a flow divider this is not possible.
The steering pump pressure line is also connected to the steering pump with a 10mm hardline and a high pressure hose. The returnline of the steeringpump has two intergrated return lines from the suspension. Returnline is 12mm the returnline from the rear and front suspension are 6,35mm or 1/4"
in front of the radiator next to the airfilter i made a loop oil cooler from 12mm tubing This is connted with hydraulic hose and just hose clamps because the return side will not create a lot of pressure.
Things left to do before filling the systems is support all the lines where this is needed. Also making some brackets for the steering oil cooler.
Next will be then filling up the suspension systems and try to bleed out some air and run some cycle with the system. I have to find a solution to turn the steering pump without the need to the engine. We will see
if there are any questions just ask
JMSpeedshop.com
This is 1996 engine from a s600 W140 with all bolt on parts
no oil cooler lines or oil cooler connected no torque converter and 2 small plastic caps missing
for the rest complete with wiring loom
weight is incl steering pump, aircon pump, 2 throttlebody's, air pump, alternator,
engine weight in total is 297KG
egine weight with throttle body's alternator and steeringpump is 285KG
these weights are with out any oil in the engine block or coolant
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
ADS suspension for S124 V8 Turbo
Just as in the front im going to modified the suspension in the back also. This will be ADS or active damping system. But then a custom made system by me JMSpeedshop. I will have a system that is ride height adjustable and option for a sport or comfort setting for the hardness of the damping system.
In the back im using a 6/2 valve and 10mm hydraulic line with 1-1,5mm wall thinkness that will run 2 seperate channels, left damper, right damper. This will have a manual adjusted setting on the comfort and sport setting dat can be adjusted with manual valve that will controll the flow of oil that can flow from the accumulator to the damper and back. This will be the same as in a regular shock absober but i can adsjust this in and out flow of oil.
The SLS system will function just like factory. But i can controll the level of the car with a electronic actuator. This will be shown in later video's. This is also not tested live. Also not yet tested in the front.
All the lines f0r the damper control are in place only thing to do is the support the lines to the underside of the body. I need to order some clamps to do this.
If there are any questions left just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes 500 SEL W140 Review & Testdrive
This Massive S-class is the W140 and really stands out from the rest of all the mercedes models. It is Just different. The build quality was just so high compared to the other brands. You could say everything after W140 was more about making money that building a quality product.
Offcourse this car has some issue's but overall it is just a fantastic car you could get these days for a low amount of money. This car in the video is on the top of the market. Very low miles and very good condition. But the price range of the W140 depends on location and engine and body type you want can go from a few 1000€ to high 50000€. It cam in 6, 8 and 12 cyl. petrol and 6 cyl diesel. long and short versions and manual 5 speed for 6 cyl option and 8 12 cyl had standard a automatic gearbox.
This car from the review is most populair model a long version with a v8. The very nice M119 5.0 32v DOHC engine . production 320/326hp and 470/480nm of torque depening on prodruction year. Still capable doing a acceleration in 6.7/7 sec to 100KPH. Dont forget this cars weight is 2010kg.
Total production of the W140 model is 406k cars and just over 26k coupe's. This car had a nick name of the cathedral because of it's massive size. In arabic country's the had the nick name "The Ghost"because of it's widebody apperiance. This car is 5.2mtr long and almost 1.89mtr wide. So lost of space.
This model in the review is for sale @ Henkgrooten.nl have a look on there website for more info about this car and the rest of there inventory.
Also have alook for the other cars i reviewed and project builds im doing at the moment. @ JMSpeedshop on youtube
if you got any questions just ask
JMSpeeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
New fuel system for the V8 turbo
At first i made a bracket for the fuel pump. So i could mount the fuel pump at the level i want it. The outlet of the filter will be at the level that the fuel line can run on the floor level into the car. Yes i run the fuel line through the car. I think this is more save the running them in the car. You will not have any chance off corrosion or weather influence. And you can not damage them when go to low to the ground. And the lines that i will use are very strong rated from 140bar .
Offcourse this was needed for the extra fuel and also because e85 will use about 30-40% more the regular petrol. Starting at the tank there is a 12mm fuel line feed to the fuel pump. The system is AN8 hose this internally 11.93mm +/- a AN8 coupling is 9.5mm +/- internally. so the 12mm fuel line is perfect. the feed on the pump is a hydraulic hose connection to AN8-AN10 because the pump in and out is AN10
The fuelpump is a Fuellab fuelpump rated for 1300HP. This is PWM fuel pump so the speed can be controlled through the ecu. so this is very nice. When i run of regular fuel i only need only max 30-40% of the pump speed.
after the Pump i have DW fuel filter with also AN10-AN8 out. from here the initial plan was to run aluminum hard line to the front of the car into the engine bay. I had 1/2" hardline. but i was not happy with the result so i pulled the feedline out. The plan was to run PTFE 1/2" with pressed connections in between the fuel rail and fuel pressure regulator and to the ethanol sensor. And from the fuel pressure regulator to the hardline same as from the ethanol to the hardline.
The plan is changed to what it is know . From the filter outlet to the ethanol sensor it is PTFE 1/2" pressed hose. with a stainless steel outliner. and also from the return of Fuel pressure regulator back to fuel tank also.
From just before the rear axle. I end with hose end fitting and will go to the fuel tank with a 12mm fuel hose. Because the return connetion on the tank is 2mm smaller. And also a 3 connection on the tank is about 6 mm i use a splitter. From 1. 12mm connection to 1 10mm and 1 6mm. so i have enough space to have as little as possible chance to buils up pressure in the return line.
To the clear AN8 is the same size as 1\2" hydrauliek used dimensions the connection for AN8 in hydraulic terms is JIC 37 degree the threads on the connection of AN8 is 3/4-16UNF
If there are any questions about this subject just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
So about 2 weeks ago i found this driveline
to find this engine and complete like this is getting more rare by the day
For me this is a pretty familiar driveline. i got this driveline also in my W201 190e V12 projecg from a few years ago
But this is a much younger generation and this is the M120.982 engine with coil plug igniton and more modern engine controls . these also had upgrade wiring looms that will not degrade over time .
this is a late '95 built engine and cam in a early '96 s600 with a 5 speed 722.621 transmission what i also in my w201 v12
this gearbox code came only on the m120 v12 so this bellhousing is unique.
i also have all the electrical bolt on parts line alternator aircon pump starter. Also the steeringpump and the throttlebody's
only thing i don't have from the driveline is the rear diff. but these are much easier to find.
Not sure yet what im going to do with this driveline. But better have it in stock when so nice project idea is coming later . you never know !!
JMSpeedshop.com
MUSIC: Alan Walker - Fade source: nocopyrightsounds
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
S124 v8 last chassis mod. finished crank case breather system
After a few very busy weeks i found a day to finally get some progress on the car. I did the last modification to the chassis. And i finished the crank case breather system.
The center shaft or prop shaft center bearing needed some modifications to fit. My center shaft is oem from W210 E420/E430. This axle is factory fit to the 722.6 amg gearbox and the oem E420 rear diff im using . The Oem center shaft bearing will not fit so i have mounted a oem e320 bearing this had also a 30mm inner diameter.
The center bearing shaft mouting point on the chassis needed to be moved 5-10cm more backwards. So this is removed from the oem location and welded back on the new spot. Everything is coated again. Axle is mounted and all connection torque down. also the heat shield is back in place.
The crankcase breather needed a vacuum connecton to the intake this is done with a 22mm tubing. The tubing is modified with a small venturi on the end that will improve the suction capacity. This is mounted in front of the turbo after the intake filter. This location will always have a vacuum, because the air filter will always have some sort of restriction.
Next will be the fuel system. i wanted to start on it already. but will do a full video on it. this will be the next one. I have already got the fuel pump and filter mounted together with all the connectors in place. Everything to get the system mounted is in house only the flexible fuel lines need to be made when the lenght is know later on.
if there are any questions just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
The S124 V8 turbo Update Engine bay
So update on the engine. Last time i put the engine back in the car. Know it is time to get all the loose ends together in the engine bay. 1e is the turbo. I needs a oil feed. This is a AN4 connection i have a pressed line with a teflon liner.
These hoses can hold high temp and high pressure and are ideal for oil and petrol also perfect for E85. So i will also use these lines in AN8 for the fuel system. For the water cooling of the turbo. It has M14X1,5 connection in the turbo. I'm using hydraulic connections for the 3/8 pipe, I welded a connection on the pipes to fit them with the correct hose diameter on the engine. cooling connection from the oil cooler is used.
The oil cooler adapeter plate is modified to have a feed line for the turbo. This is aM10x1 adapter to AN4 hose. Also the oil cooler thermostate is in place. But needs to be secured correctly. Below you can find a picure of the oil cooler line connection
Transmission cooling lines are in place and connected. but need so support to keep the lines in place.
The throttle body is turned 90 degree for oem position to make space for the changed vacuum connection for the brake booster. IAT sensor place in the feed pipe to the turbo. Because of changing the positions of the throttle body the piping from the intercooler did not fit anymore. This is modified again.
Radiator incl. cooling fan from SPAL is mounted. All hoses are connected. Only 1 connection to the waterpump needs to be blocked because it is not used.
Intake manifold is placed incl the spacer plates the cover the air injection ports. Also air injection port is blocked. Injectors and fuel rail are mounted. The injectors are a little higher so spacers are made for the fuel rail to sit higher. The injector Are 1100cc. See picture below
Engine oil breather system or overpressure system. I have modified this system with a Mann + Hummel provent 200. i bought a aftermarket housing but i have the oem filter LC5001x. There are AN12 connection on each valve cover. OEM connections are blocked off. The AN12 from each valve cover go to a T piece with a single AN16 line to the provent 200 case. From this point i have to make a vacuum connection in front of the feed of the turbo to create a underpressure in the crankcase . This will be shown in a later video.
Things that needs to be finish mechanically before wiring job starts are . Propshaft center bearing needs to be fitted, fuel system from tank to fuel rail and the rear self leveling suspension hydraulics need to be build in the car . When this is done the wiring needs to be put in place
If there are any questions just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes 280CE W123 1981. Collectors item!!!
This is really a beauty. A example of how the W123 really where in the 1970/80 years. This model is the 280CE 6 cilinder model. The CE is also delivered in the 230CE model with a 2.3 4cyl engine . The 280 is a 2,7 ltr 6 inline or 2746cc. people call it a a 2.8.
W123 model is build between 1976-1986 and the coupe between 1977-1985 up to 1978 the 280 was a C modell without the E for injection. These cars had a carberator. from 1978 the kjetronic was availible and the model is called a CE.
This M110 engine 2746cc is used by mercedes from 1972-1989 in W114 W116 W123 W126 R107 and W460 G-klass modell in other models Kjetronic was already availible from 1975 and up.
The M110 engine had a compression ratio of 9:1 and is a dual overhead camshaft engine but with 2 valves per cyl. Power delivery in the carb. versions was 177hp @ 6000rpm and 234nm @ 45000rpm in the later kjetronic cars it was 185hp @ 5800rpm and 240nm @ 4500rpm. Perfromance of the car was 9.9 sec from 0-100kmh with a top speed around 200kmh or 124mph
2686915 cars are build in the version of the W123 in total most build model is the 240D with 455k cars. This is almost 1/5 of all the w123 produced. Various models where build like a sedan coupe estate an limo and a even longer stretched version
This car is for sale @ Henkgrooten.nl
if there are any questions just ask
JMSpeedshop.com
MUSIC: Rewind by Markvard
done a review and full testdrive on this car
@henkgrooten.nl
also have a look on JMSpeedshop .com
with the filled up torque converter
M113 v8 turbo engine is going in the new repainted engine bay
also this is insulated and ready for the engine
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 V8 turbo Engine & transmission back in the car !!!
After the engien rebuild and the service of the transmission the driveline can be put back in the car. Since the last long video i did some little mods to the engine
I made a oil return line for the turbo with with a connection on the old oil level sensor location. Also a bracket was missing from my steeringpump. This is also in place now. The oil sensor location also needed some chances. Beacuse the sensor is to big that i using and would run in the multibelt in oem location. I made a new plate for this. Also i have test fitted the aircon pump. This also needed a mounting point on the back to the engine mount. This is al fixed now
Also started with the engine oil breather. I have made 2 big connection on the top of each valve cover. this will have a hose connection to the location behind the passenger front headlight. There will be a swirl pot with a connection in front of the turbo for vacuum.
The torque converter is also filled up with as much oil as possible. Will be a bout 2 ltr i think. this will help bleed out the air when filled up the transmission when running it for the first start up.
Engine and transmission are connected with 12x M10 bolts torque done according oem spec 39NM
The torque converter has 6 small M8 12.9 bolts to hold the converter down on the flywheel there need to be torque to 42nm accoring oem spec
The front wheel are removed again because i have to lower the car as much as possible to get the driveline over the edge into the enginebay. This driveline is pretty easy to fit in the w124 enginebay. This engine is much smaller the i am used to with the v12 in w201. There is just so much room
The engine has 2 engine mounts with a each a top and a bottom bolt to mount it on the chassis. The transmission mount has 2 bolts to hold the mount on the transmission and 4 bolts to mount the transmission mount on the chassis
This is all fixed . Driveline is now ready for the rest of the parts to be mounted. And i have some space again in the garage.
If there are any questions just ask
JMSpeedshop.com
MUSIC: Rewind By Markvard
for more about the build see @JMSpeedshop
also visit jmspeedshop.com
this because the manifold is only hold on 8 small m6 bolts
engine is almost ready to go back in the car
this pump is fitted on a M112 and m113 engine
on S210 Estate model the self leveling suspension is standard
i have modified the suspension. i also have self leveling in the front of the car
so the pump needs to feed a double system. that is why i need to know the flow at idle and at higher Rpm so i can calculated the flow
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes 722.6 Transmission service and valve body check
The transmission I bought about 4 years ago i think. With 170D km on the running gear. So it is good to know if this number makes sense when i open the transmission for a check and little clean up. Also there are some parts that need to be changed out. Like filters and the PLIL parking lock connection.
This transmission has OEM code 722.624 These are normally in E55 AMG NA cars. So this is a transmission from around 1998. Also this transmission has still the torque converter with the drain plug in it. i think this changed around 2000.
I have drained the oil from the torque converter and from the transmission because these where still full level all the time since i had it. The oil does not look that bad. The color is pretty light for this to be the first oil. When removing the oil pan the oil filter is showing 1997 production date. So this the first filter or it can be and long on the shelf item.
The oil pan is not having a magnet. If i remember correct the early gearboxes did not have this. But im going to order this and install it.
PLIL is a part that you should always change if you open the transmission because there is a rubber piece that can break over time. and will give a very big leak. In my case i also remove the parking lock mechanism. Because this part needs to be connected with a cable in the oem cars to the steeringlock and the ignition key. In my w124 this will not work. So i will only have the parking lock from the shifter
Removing the valve body. The conductor plate is removed incl alle the solenoids. The plate looks pretty good. But i have a new one just to be sure. I will keep the old one as a spare. The valve body can be split but make sure you have the big side on the bottom. Because in this part are all the steel and plastic balls that will otherwise drop out.
After removing the the balls, filter, checkvalve and oil out of the valve body parts. I left them overnight to drain out fully. Next day i check all the springs and pistons in the valve body (see pictures below). Everything looks just like it should be.
i also drilled the 3 to 4 flare bigger to 4 mm just like on the ofgear website. This include a little software change will solve the problem
and will make the shift also under full load better then without this modification.
Im going to run a standalone OFGEAR.DK controll unit for the transmission have look on his website
This the valvebody can be assembled again with new filters. Before the conductor plate and solenoids can be mounted again, I checked the solenoids with 12v if the where werking. All are okey. The valve body can be put back in the transmission case and the new filter can be mounted. When i have the magnet for the sump i will mount the pan with a new gasket.
If there are any questions just ask
JMSpeedshop.com
for extra info or a manual from a 722.6 visit the link below
ATSG gearbox manual
http://www.w124performance.com/docs/mb/transmission/722.6/trans_722.6_ATSG_2004.pdf
Febi biltstein Service kit : 100254
The Torque values. bolts in oil pan, valve body mounting to transmission, vale body splitting bolts M6 bolts . to 8NM
Torque value for Valve body side covers M4 bolts to 4NM
Torque value for connector bolt to 2,5NM
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
HOW TO: Thermal Heat insulation (ceramic wool + stainless shield spot welding)
You always see the big tuners with very expensive high end car running these very cool looking insulated exhaust. How do the do it and what is used.
We are all familiar with the shield bands that are put around the exhaust. This is helping for sure. But in the engine bay you want to keep as much heat in the exhaust as possible. So i did some research because the end result also looked very cool and nice.
I used a material from a company in germany. called HJS. THis company has dealers that will sell this product for them. I bought a set with partnumber 83000027 This is 1m2 of ceramic wool 5mm and 1m2 of stainless hammerd shield of 0,1mm
The wool has a sticky side and can put on the exhaust and will stay on. works very good. After this the big puzzle begins to get the stainless sheets on the exhaust.
I have searched and got a mig welder. and used this without a welding wire. So i can spot weld with the machine. The biggest problem is find the right settings and best way to weld it together without burning a hole in the sheets. I started with the manifold which where the hardest to do. maybe not the best idea. After this i did the connection pipe between left and right bank. This was already much better. i think it is a learning process. Earth connection to the material is very important.
if there are any question just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
HOW TO: M113 intake manifold assembly “Part2”
The assembly of the manifold is pretty simple when everyting is cleaned. The only thing i did is de-greased everything with brake cleaner before putting the sealer on. The internals i left clean. I put the gasket on the housings internally. just a small layer so it will not be to much
When the internals are put in place there are 4 small bolts that keep them in position.
the bottom housing has a flat top surface. The top part is having all around the edge a small channel where the old gasket was located. I have put the channel full of gasket material. Make sure there is also a little above the surface of the channel so it can make a closed surface when mounting together.
After putting the 2 housings together there are all around M6 bolts. I have putting them hand tight . normally M6 is about 10nm. but i dont want to overstretch the magnesium housing .
I also have space enough to look in to the runners to see if there is to much gasket material and i have removed this on some spots
if there are any questions about this subject just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
HOW TO: M113 intake manifold dissassembly "Part1"
The intake manifold is a part on this M113. But also on the M112 engine. That is according mercedes not serviceable. You can not order any parts internally for this manifold. Only the complete unit . Also there is not much info in the Mercedes manual about this. There is noting about how to dissassembly it.
But if you look inside trough the throttle body entrance. Or through the runners. it is really dirty. This because of the crankcase breather connection to the intake and the EGR system. This combination will created the oil exhausr gas mix. That will back carbon on the intake manifold and Leave a black oil substance everywhere in the manifold
This will have influence on the temperature and optimal flow in the manifold. So for sure after a Engine rebuild this needs to be cleaning The manifold is pretty easy to dissassembly. The are 4 top parts and 2 bottom parts.
The top parts are. Outside cover. The inside channel seperator. and 2 small parts that are mounted on the channel seperator.
The bottom half parts. Outside cover and inside channel seperator with flap assembly.
I cleaned all the parts with a regular degreaser. This intake manifold was easier to clean then all the other engine parts. And this is because the Temperature in the intake manifold will not reach a high temp like 100 c in the engine . The intake will max hit like 60c. so the oil exhaust gas mix. will not get backed as in the engine .
The parts from the intake are dont have much in perfections on the inside. the only thing i found where some cracks on 1 mounting point of the fuel rail. but this could be there for years i think. I will have a look to support this a little better so it will not brake of in the future.
Also to mention there is a vacuum chamber in the bottom half of the manifold. This is used for the actuator the controls the flaps for long and shorter routing. this chamber has 2 plastic covers on each end and has a rubber plastic mounting that was old and damaged in my manifold.
I don't really like the design because it is not easy to reach and there are no parts that can be ordered. so i will block all the holes for this chamber. and use a different vacuum solution for this
if there are any questions just ask
JMSpeedshop.com
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 Installing oil sump's Oil filter housing and Flexplate
Im almost there with finishing up the rebuild of the engine. Got both sumps back on the engine. In between there is a layer of silicone gasket and all the bolts are M6 only 2 are M8 and need to be put on torque M6 10nm M8 20nm
The oil filter housing is havind several loose parts. that need new o-rings. There is a big O-ring like gasket under the filter housing. This is hold down by a 46mm nut that need to be put on 70nm. afterthis there is a plastic pipe with 3 new o-rings that is inserted. And at last the filter is put in together the cover that needs to be put on 25nm
The flywheel needs new bolts evertime it is removed. The torque value is 45nm and 90 degree angle.
For the oil cooler i have changed to a external oil cooler so i made a adpater plate for this but the the M6 bolts need to be carfully put on torque. i already made 1 bolt of the 4 to m8 because of damaged threads. so normaly m6 needs to go to 10nm but be carfully 8nm will maybe save you from damaged threads here.
if there are any questions about this subject just ask
JMSpeedshop.com
MUSIC: Rewind By Markvard
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 Cylinderheads Camshaft Bearing Bridge Installation
Got the cylinderheads back on the engine's on both sides. also the camshaft bearing bridge is installed. Cam sprockets back connected. chain Tensionair back in place. And the crankpulley mounted and torques
To put the heads on, there is a small seallant line needed around the cylinderhead on the outside and around the coollant and oil ports. But "not" around the cylinderbushings them selfs.
Normally when you got a headgasket there is on some placed some seallant. But with Mercedes this is not the case. In the manual there is standing there is seallant needed on disorted or corrosion spots.
But on my old gasket there was on much more places seallant and im not the only one that has seen this. There a more people with rebuilds on the m113 that have this. So i applied this on both sides of the headgasket.
I have put the head on torque using the oem sequence but a different amount of torque because of my new headstuds that im using. The final torque firgure is 110nm and done this in 4 stages.
if your interested in a set of headsuds follow this link
These camshaft bearing bridge need to be mounted equil with all the bolts in and the screw done. All the bolts need to be renewed.
When putting the head on the block it helps to but the chain tensionair in for the moment because placing cyl 1-4 heads is easier. After this pulle the tensionair out again
When the heads are on the block the sprockets can be mounted on the cams. Now these are on torque the tyraps can be removed from the cams. The chain tensionair can be put back in and put on the richt torque setting.
Also the crankshaft pulley need to be put on torque this needs a massive 200NM and then a 90 degree angle.
Finally checking if the timing is correct. Turning over the engine 14 times and the marking on the cam sprockets need to be back on the chain marking. Also the crank pulley needs to be on 40 degree s
Also have a look to the other rebuild video's of this engine
JMSpeedshop.com
MUSIC: Rewind By Markvard
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 Timingchain Oil Pump and Timingcase install
This is will make the engine look more coming together. This is a pretty important part of the installation. because the chain is what makes or breaks the engine if it is no correct.
So at first. the sprockets are mounted. On the crank it is slide on. The center sprocket is with a left threaded bolt. This is the only bolt in the engine that is having this left thread. so keep that in mind. After this the quide's are installed. And the chain can be put in place. Take a good look at the copper coloured markings. The need to on all the sprockets on the right position. Also install the cam gears. And lock them with ty-raps so the will not drop.
The timing case has a lot of bolts with different lenghts. There is a spec sheet in the manuals where the will go. All the bolts that will hold the cover to the block are M8 and need to put on 20NM. The extra bolts for the waterpump are M6 and need to be put on 10NM
It is also very imported to follow the sealer instructions for the Timing cover. because there should not be put sealer on all the channels. The oil channels should not be sealed. This to prevent getting gasket material in the pressure channels.
if there are any questions just ask
JMSpeedshop.com
Music : Rewind By Markvard
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes S63 AMG 4-matic W222
The S63 is already a lot of generations. This is the 2e and last generation having the big 5.5 liter bi-turbo. The massive torque machine producing 900nm
The engine is 5461cc DOHC v8 with VVT on the intake and exhaust cam. Also a compression ratio of 1:10 CR. The engine has 2 Garret turbo's and water to Air intercoolers with a max boost pressure of 1.3 bar. The engine is also direct injected with a fuel injection pressure in the range of 100 - 200bar
The engine is connected to the last generation 722.9 MCT transmission but is not having a race start function . But is not really needed because it is still capable of 0-100kph in 4.0 sec. with this very good 4 matic system.
The car is also availible in a RWD system but with 900nm this not really a good idea. the HP number for this engine 585HP and has a rev limit of 6400RPM. but depends on in which gear your are with a soft rpm limiter. Speed limint is 250KPH but can be raised from factory when a AMG drivers package is also in the set.
The M157 engine can have some issue’s so do your homework when your in the market for a car with this engine code here is a link
tuningpro.co/the-5-most-common-mercedes-m157-amg-engine-problems
Also have a look on henkgrooten.nl where this rocket salon is for sale
if there are any questions just ask
JMSpeedshop.com
MUSIC: Jeff Kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 Crankshaft & New Rods + Piston installed
Got the mainbearing caps removed. Rods and pistons are ready to install. Only thing i needed to do was measuring the piston ring vertical play and the crankshaft axial bearing play. This was all in factory spec.
I cleaned for the last time the bearings and blow through the oil channels. Before putting the Crankshaft in the top bearing housings i pre-lube the shell with assembly lube. This will keep the engine from running Dry when i start the engine for the first time on the starter motor. Before all the oil gallery's are filled it can take up 1 min.
The lower bearing shell are placed and the new bolts are pre lube with engine oil. All caps are put on torque according factory spec and sequence.
Next are the pistons and rods. Im placing the journal on the lowest point when sliding in the piston with the rod. So it is already in the position that i can place the bearing cap and put the bolts on torque. Without moving the crankshaft. When moving the crankshaft with bearing cap there is a chance the bearing will slide out the housing.
The new rods need to be torque'd down to 75nm i did this in 3 steps bolts are 3/8".
Also when turning the crankshaft i can check if the new rods are running free and not touching any other objects like the oil squirters. Next thing i have checked. Is the free play between the piston and Crankshaft.
Before i got this Rods made i also thought about shorten the rods to lower the compression. I now have the oem size and compression. But when measuring the play it is only 1.5mm between piston and crankshaft . So this much room is no left. See photos below
for any questions just ask
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
V8 Turbo. NEW RODS & HEAD STUDS + Project goals !!
I have measured almost every clearance at this moment only the crank axial play and piston ring vertical clearance need to be done
I think did not share any info yet on what the real goals for me are in this project. I changed some idea's along the way. But i did never mention these things. In the beginning i just wanted to build a S124 with a m113 v8 just with the oem setup so 306HP and a 5 speed auto box.
The second thing was at a turbo to get some more power and a little more technical aspect to the build, I also added the 500E bodykit to the project to make the look more special. Beginning this year i made the change to getting more out of the engine when i run on flexfuel.
The engine will have a base setting on 95 octane fuel what will be around 0.5 bar boost pressure and give around 400hp and 600nm on the crank. this is a quess. when running on E85 i think i can get to 700hp and 900nm at least and i will max out 750hp and 1000nm because i want to run a reliable setup. the transmission can handle 1100nm in stock form but i don't want to stretch.
Because of this pushing more out of the engine i think the rods are not strong enough in this 5.0 engine. So i got custom rods made in a I-beam profile with rifle drilling so there is an oil channel to feed oil from the big end to the small end. These rods are rated to 200HP per cylinder. The rods have 3/8" rod bolts .
I'm also upgrading the headbolts to headstuds. I wanted to go with ARP but ARP is very hard on small quantity. Only other supplier is weistec. But i think these are also ARP. And i'm in Europa and did not want to wait for long delivery times. So through one of my contacts. i got a supplier that could deliver me custom head studs to my specs of lengt and dimension. The have experience with this dimension running then up to 3.0 bar boost pressure. The bolts are rated to have around the same spec as ARP 2000. The dimension will have 7mm more threads down the block and having M11X 1.5 in the block just like oem and on the head side M11X1.25. like same spec as ARP is using.
I have 1 extra set in stock of a connecting rod set. and the will fit in a m113 5.0 and 4.3 and have the oem lenght so keeps the 1:10 CR ratio if the oem pistons are used. if you are interested contact me through the contact page
I can also get extra headstuds set. ask me for pricing
extra info on the oem piston is 56mm high with 2mm flat dome on the head. head thickness at lowest 5,5mm. If somebody has the oem thickness of a m113k piston let me now then we can compare these
if there are any questions just ask
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
HOW TO: M113/M112 hydraulic lifter how do the work?
The hydraulic lifters, almost never fail. But the can get damaged or stuck, this will most of the time start with knocking sound on a cold engine. And the warmer the oil gets the sound will go away. This is the point the lifter is loosing oil or can not keep the pressure inside.
Most of the time this has to do with dirty oil. Or not enough maintenance or changing the oil.
There are 2 types of element where only the bottom part. where the check valve is in. Is different. The exhaust lifter has a small hole and the intake lifter has a big hole. It is very easy to see.
For a complete V8 there are 8 exhaust lifters and 16 intake lifters.
When removing the lifter or removing the camshaft bearing bridge it is important to reset the lifter. This needed because when the camshaft bearing bridge is reinstalled. There is a possibilty the lifter is adjusted to much so it will keep open the valve when it needs to be fully closed
When the lifter is removed. it can be split in 3 parts. Top and bottom and a spring. You can also take the check valve apart. But i don't recommend doing this because it has very small parts. and it is not really needed because it can be tested very easy. without removing. see video.
So if there are any questions left after seeing the video just ask
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes ZAS Code: 479 Cylinder cut out system
This system is found in the W220 and the W215 as far as my info is going. It was optional on the m113 and standard on the M137. This is as far as my info is going. The engine i have is a M113.960 engine with the option code 479. This means it can cut the ignition and injection on cylinder 2,3,5 and 8.
This igntion and injection cut is pretty simple. Just electronic controlled from the ecu. But also the Valves of these cylinder stay closed when this is activated. This means the rockers on these cylinders on the intake and exhaust valves will be split. There is a piston assembly in the rocker that is controlled by oil pressure.
When the solenoids on each back is activated oil pressure is pushing a piston out of the rocker that is running on the camshaft. The other half is disconnected and is staying steady on the valve spring setup, leaving the valve closed.
To activate this. Certain driving and load conditions must be in place for the system to work. most of this is in low load cruising. Mercedes is giving that when driving 55mph it will save 13% fuel consumption.
If there are any questions just ask
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
HOW TO: M113 camshaft bearing bridge assembly
This is the last part of the engine i need to clean and inspect before everything can be assembled again. The camshaft bearing bridge is a part that needs to be handle with care. Because it is a part that is machined to fit the head. So if it is damaged or the head is damaged it needs to be change out together.
In my engine i have option code: 479 ZAS cylinder cut out system. This means this system has more parts then the regular engine with this option. But the process is the same. Difference is in the shafts that has an extra oil channel and the 4 sets of rockers are different. These can run in split mode. so 1 part is still running with the cam and the other part is standing still when activated. There is a seperate video of how this is working in detail.
Just make sure all the parts are clean and have no excess play or deep scratches. The hydraulic lifters or compensation elements is also in a seperate video.
If there are any questions just ask
JMSpeedshop.com
MUSIC: Jeff kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 Oil pump assembly internal cleaning
Im doing the rebuild of the engine and want to have a look in the oil pump. To see the addition wear and condition of the pump. The pump is in 3 parts with 2 gearhousings. Hold together with 4 M6 bolts. The pump has no gaskets. It has a machined surface with the steel gears inside
The first gear section are the same outside diameter. But the height is a little less then the second stage. The pump internals are not really having any wear only on 1 side of the gears the look like polished. this is where the gear tooth are touching each other, and how the gears are turning each other
i cleaned everything and put it back together. The bolts are put back on torque. 14,7 nm
for any questions just ask
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Cylinder head rebuild. lapping valves and vacuum testing heads
so done a lot of work on the heads. the camshaft bearing bridge was already of. So only the valves springs and retainers holing the valves in place. Also the heads where pretty dirty. Lot of carbon and grease build up.
I removed the valve springs so i can remove the springs. i marked them al on the top of the valve shaft, so i can place them back in the same place. This is pretty important because there is always difference in the seats and the valve surface. So best is to place them in the same position so you have the biggest chance of have a good seal.
The intake valves where only a little greasy. i socked then in ammonia for a few hrs and them cleaned them with some paper. The exhaust valves had some very big carbon build up that i remove with a brass bruss on the drill bit to grind of. The valves are very hard and the brass is much softer so it will not damage the valves.
After also cleaning the heads with socking in ammonia for 24hrs and pressure washing them the came out pretty clean. After this is place the valves and relapping them with the small grind grit to get a good sealing surface.
After this i made a test tool with a vacuum meter and a steel plate with a rubber piece on i can pull the chamber under vaccum to check it if is sealing good.
on 1 cylinder i had to relap the exhaust valves again because it was not pulling the full vaccum. Also to remember is that the exhaust chambers are all connected because of the EGR system. so to test the vacuum all the holes need to be blocked off with rubber pieces. But it worked out pretty good.
Also i have send of the Engine block to be resurfaced on the top see the picture's below why
if there are any questions just ask
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Best way to clean your pistons
This solution is pretty easy and is very cheap in materials that need to be used. Remove the piston from the rod. Remove all the rings so it is easier to clean the rings and caps. Rub of the top and loose materials and carbon.
I'm using a brass brush and cleaning sponge. Prevent rubbing to much on the skirt surface. Most of the time there is a coating layer on here that you don't want to damage.
So get a cup or something that you can close of. Where all the parts fit in.
The matrials using from this job is regular cleaning ammonia. That can be found in the supermarkets for around €1,- per ltr this will hold max 5% of ammonia. But be carefull this can still harm your so protect your sell and read the safety card on the bottle.
Put the piston and parts in the ammonia so everything is under the max fluid level. leave it for 5 hrs and check the parts. or just leave it for 10hrs or so. you can get the carbon and other deposits very easy of the piston without hard rubbing
JMSpeedshop.com
Music: Jeff Kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 crankshaft + rods + pistons removed S124 V8 Turbo
This are the last parts that need to be removed and also when removing these parts some important parts will show the wear. The full cylinder bore, the main bearings and conrod bearings can be inspected now.
The connecting rods are removed incl the pistons . The rod bolts are removed with the bearing cap. all the rod bearings are showing wear. There is also some dirt and very fine lines in the journal that can be polished out.
The main caps are removed and the journals of the main bearings look much better and are not really showing any wear. When pulling out the crankshaft. I as a little surprised about the weight of it. Is far out the most heavy part in the engine.
I'm now going to send of the crankshaft for rebalancing and also let the journals to be polished and measured. So i have a clean starting point.
JMSpeedshop.com
MUSIC: Jeff Kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 dissassembly "part 2" S124 V8 turbo
In the 2 part i remove the timing cover and the timing chain and the 2 sump parts. what was very interesting to see is how the coolant passages would look. these are running from the coolant pump into the block. These are famous for swelling up and or crank and create a coolant into the oil. These cost a few euro's but are a lot of work to get to.
In this engine the where alos already bigger then the should be. Also there where parts missing from the o-ring. but it was not damaged that it would let coolant into the oil.
the chain was looking normall but when i have the new one i will see the stretch in the chain. The chain guide's had some wear and some cracks in them but there where no parts missing on them. im going to renew the chain and the guide's incl the oil pump chain and guide. Also the tensionair will be renewed.
The bottom oil sump is alse removed there is some oil left in it what i will inspect for particals if the are there. the low part of the engine is alos removed. and is only showing the same carbon deposits in it what is also showing in the rest of the engine.
in the last part i will remove the pistons and rods. incl with the crank shaft. and also will have a look at the bearings and piston rings.
if there are any questions just ask
jmspeedshop.com
MUSIC: Jeff Kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
M113 engine disassemble for the S124 V8 turbo
I have this engine i think 3 years waiting for this point . i bought this engine with on paper 170k km. I never seen it running. But offcourse it it always a little gamble. These engine can get pretty dirty when so seals start leaking like on every engine. But also internally because of the emmission system and the oil change periode. what will be around 20k km or so i think . Also on ths engine it is showing carbon build up in the crank vent covers and under valve covers and down the chaing routing into the block.
These engine's have a reputation for being very reliable also at higher mileage. so im not to worried about it. 1 thing that i want to see is clean cylinder walls. that is the most important because of the alu sil block.
i have checked the timing and there is stretch in the chain between bank 1 en 2 it is 10 degree's and alos what is weird is that the bank 2 cyl 5-8 is 5 degree early on the timing mark 40 degree . so it should be on 40. this would indicate a shorter chain. what is not possible. or the chain guide must be worn in extreme . We will see this later.
the valve train bridge is dismantled. there are 21 bolts on each side that need to be loosen in a certain stage. these bolts are torque to yield so need to be renewed.
My engine has alos a rare option that is ZAS or SA code 479. that is cylinder deactivation. This is a solenoide controlled system that can switch of cyl 2-3 and 5-8 on demand . and only runin on the othere 4 cyl. this will alos cut ignition and fuel. around 55 mph this would save 13% fuel consumption. this system would be possible to run also on my turbo settup because the cylinders would be full closed so it would not have any influence on the rest of the engine. I'm not sure if im going to use it . But i will clean and check everything so when i want i can use it.
Cylinderheads also need a sequence for loosen the bolts. the came of pretty easy. and there is some carbon build up. The cylinder walls look normall. No shiny lines or scratches. The top is showing some carbon build up but nothing to serious.
In the second part of disassemble i will remove also the timing covers then i can turn over the engine and see also the other 4 cylinder walls.
See below for documents i have used. If there are questions just ask
JMSpeedshop.com
MUSIC: Jeff Kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
S124 V8 rebuild chassis and engine bay after paint and coating
So after a little pause in the project with holiday's and finishing the underbody coating and engine bay paint. It is hands on to build everything back for the last time. So front suspension is back in incl brakes and wheels. Also brake lines and ABS sensors are in place. The shocks in the front need new protections covers. The are on order.
The steering housing is mounted incl the connecting arm. the wheels are alined as good as possible to this point. I have also installed the hydraulics for the suspension in the front. incl new accumulators. and connected all the hardlines.
The rear axle is put back under the car incl the rear stabilizer. But not the one i wanted because the thicker W210 model does not fit because of the mounting of the accumulators in the back. so i mounted the oem one.
Rear brake lines are also in place. now the last thing on modification is the rear bearing of the center shaft this is because the center shaft is also from a W210 model.
When the rear hydraulics are in place i will start on the engine rebuild.
JMSpeedshop.com
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes GLC 63s edition 1
This the X253 model that came on the market in 2015 and is still in production. The Amg version's came in 2018 the 43 63 and the 63S. The 63S edition 1 like this one had a new price of €187k,- what is a massive new price.
The GLC amg is the same spec car as a C klasse AMG with small difference like it came standard with the 9 speed 725 gearbox. also this has 4matic+. That is permanent rear wheel drive. when need the front axle can get up to 100% torque on every wheel. Also the GLC is equipped with are suspension with 3 settting comfort sport and sport +
The gearbox has 5 settings comfort, sport, sport +, race and individual. the race setting is only on the S model. and the individual is for your own input on suspension transmission and engine setup throttle response.
The engine is a M177 3982cc V8 with dual overhead cams and vvt timing. direct fuel injection and hot V setup for the single scroll twin turbo setup. The boost pressure is 1.2 bar boost. This will give the S model. 510HP and 700NM 0-100 is possible in 3.8sec.
The car weight is 1910kg the trunk space in 550L with the rear seats down 1600Ltr.
I performed a race start in this car and the 0-100 is really quick. but the last 1000rpm is not really needed. the car makes less torque and hp outside this range. for the rest i prefer this car above the GLC above the C klasse
if there are any questions just ask
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
The Mercedes A124
Mercedes E320 Cabrio. This car came on the market in 1992 and is the longest produced 124 model in the range. The W124 is for me the best mercedes ever build. The quality is just very high. But also the driving experience is still better the a lot of new cars. The way a 124 model handles is just so good and this 1993 car is almost 30 years old.
The A124 models cam in 1992 with 1 engine option the 3.0 24V m104 engine. In 06-1993 this change to a 3.2 24v 6 cylinder because of lower emission and engine sound. the 3.2 could deliver the power at lower rpm's
Next to the 3.2 there where also 4 cyl version the 2.2 and the 2.0 with 150 and 136 hp
The 3.2 delivers 220hp @ 5500rpm and 310nm @ 3750rpm the car had a top speed 230kph and 0-100kph is possible in 8.3 sec.
The carbio is based on the coupe. The loose 28kg on the steel roof but adding 130kg to support the chassis. and another 43kg for the roof. so the end result is around 1700kg depends on if it is manual or automatic .
the boot is also a little smaller. This came to 300ltr. what is 180ltr less then the coupe
in totals the carbio is 33952 times build with a extra not official 68 3.6 amg cars
This car is for sale @ henkgrooten.nl have look for more info and pricing
if there are any questions just ask
JMSpeedshop.com
MUSIC: Jeff Kaale - Pillow Talk
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Wiring loom removed engine bay painted S124 V8 turbo
This was a pretty time consuming job. Getting the wiring loom removed from the engine bay and collect info about all the plugs. document and label everything is very important because after a few weeks you wll not remember everything. there is about 50% of the loom that i can delete because it is for the old engine controls and ecu.
Before i will build everything back i will remove everything up till the fuse box so there will be no confusion about loose wiring in the future.
the fuse box is removed and the holders for the relais and fuses are inserted in to the car trough wiring loom hole back in the car. I also removed all vacuum lines and the the brake booster. to my surprise only found dirt and no rusty places like on the wheel wells. You would think that dirt is staying wet longer and will create corossion spots but nothing to see.
Everything is cleaned up and sanded down with scotchs bright. everything is masked of and covered what was nog needed to be painted. also the hood is removed for better access, The hood is also painted on the inside . The engine bay is painted above the subframe so every in the engine bay is black. this is a easy color and will match every exterior color in the future.. black is also easy to maintain and repair if there will be some damaged to the paint in the future.
if there are any questions just ask
if there are any questions just ask. and have a look in the playlist . youtube.com/jmspeedshop
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
So i have Complete drivetrain removed engine+transmission+rear axle S124 V8 turbo
And this for the last time. i have everyting fitted in on the place where i wanted it. so far. So the underbody can be restored and new coated. I have some small rust spots to fi and remove all the surface rust. Then place a antirust coating and a new rubber coating under the body.
Also engine and tranmission is out. engine will have a slight rebuild . Transmission will be resealed. and valuebody will be cleaned.
Wiring loom out of the engine bay will be removed. So the engine bay can get a new fresh paintjob.
for the full playlist follow the link youtube.com/playlist?list=PLy5UV-uDczfS-vA71aluvWBFaYS1pEzYb
if there are questions just ask
MUSIC: Maxwell - Ready
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
The Nissan Patrol Barra G42 1000HP First start
This is project buidl by Speedshop Ter Stege. This company is a specialist in Turbo's and hybrid turbo building. But the also do projects like this Barratrol. This car is build for them self. Goal is around 1000HP and just see where the limit is. It is a sleeper, Offroad, Dragcar and just for fun.
Here in europe is a Ford Barra engine pretty rare. Because the were never delivered from factory. It's a Australian Market suplied engine for trucks mainly. And very easy to find there. So this Swap is more common there. Also in the USA the barra engine is little more known. But here in europe an The Netherlands it is just rare.
The Base is a 2000 Y61 Nissan Patrol. The engine is a Forde Barra FG engine. this is standard the best head porting and cams to start with
This engine is build here is a parts list
CP Pistons
Noname Rods
Crow springs and retainers
Stainless exhaust valves
upgraded oil pump gears
Ross vibration damper on the crankshaft
Standard cams with light headporting
Girdle Main studs and headbolts
Engine base is a NA 4.0 FG engine
Turbo is a Pulsar 7975G AKA G42-1450 dual ball bearing turbo
Ecu is MAXX ecu Race
For more info about Speedshop Ter Stege. follow them on facebook and instagram
Facebook. facebook.com/speedshopterstege
Instagram. instagram.com/speedshopterstege
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
The Mercedes SL63 AMG P30 R231
This i think the most powerfull car i drove that can put the power down on the street. This 900NM V8 bi-turbo. has almost no wheels above 50km. And When it is in gear and it will put all the torque on the rear axle alone. It moves!!
This R231 is build from 2012 up to 2020. this 2013 car is before the facelift and the power upgrade. So from factory this SL63 came with 537HP and 800NM. But with the perfromance pack you got 27HP more and 100nm more. so final output is 564HP and 900NM.
Included in the P30 pack is power upgrade. also LSD 40% diff. carbon rear wing . Carbon engine cover. Alcantara/nappa steeringwheel. AMG drivers-pack that also raised the speedlimit from 250 to 300kph. also Red painted calipers
After 2014 there is a facelift of the R231 also the power is increased to 585HP and 900NM. I could not find this info but the P30 package would not incl a power upgrade after 2014 i think.
The beautifull color on this car is a designo color. called diamond white code 799. With the black wheels and carbon trimming this is really standing out on the car.
The engine is a M157 V8 bi-turbo that is based on the M278 (4.7ltr) . This M157 is a alusil opendeck block with DOHC and VVT on the intake and exhaust. Capacity is 5461cc and it is direct injected. Fuel pressure range is 100 - 200 bar. compression ratio is 1:10. 0-100kph is possible in 4.3sec with the P30 pack it is 4.2 sec
Brakes are 390mm front and 360mm rear for the steel standard setup, optional ceremic is 402mm front and 360mm rear
Weight is 1745KG with a 75L fuel tank. Boot space is 364L up to 504L depends on if the roof is down or up
Suspensions is ABC just like the R230
This car is for sale at Henk grooten. have a look on his website Henkgrooten.nl
Also have a look in the AMG playlist
If there are any questions just ask
JMSpeedshop.com
But the frame is custom made
not a lot more info about this bike
I was filming a review about a Mercedes SL63 AMG
And this beautifull piece of engineering was show off in the showroom
what a masterpiece
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
The S124 V8 Turbo 3" MagnaFlow Exhaust is done
Exhaust from of the turbo is a full 3" 76mm exhaust.. i have used 2 muffleres from Magnaflow. Middle muffler is a 4"X 9" Oval X 14" lenght . Magnaflow part numbers is 11219. The End muffler is a 5"X 11"Oval X 22"lenght. Magnaflow partnumber is 12589.
The exhaust has a support on the oem connection on the transmission just behind the sump. There will be another hang on point just before the rear axle. and there are 2 in place on the rear end muffler. For now i don't have a flex piece in the exhaust. The engine block is on urethane mounts so will not move a lot. I will decide later what i will do. but for now i leave it like this.
I can dismantle the exhaust behind the turbo in 3 pieces. End piece from behind the mid muffler. Middle piece from half way the downpipe to behind the mid muffler. and the downpipe from of the turbo and the wastegate down.
Also have a look in the full playlist off this build on Youtube Or the full build on JMSpeedshop.com
If there are any questions just ask
➤Patreon: patreon.com/jmspeedshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
S124 front suspension is working!
The car is going up and down and is holding pressure. So i don't have any leaks internal through the level valve. Also no external leaks on coupling or so. Pumping up the car is now through the old hydraulic pomp controlled with a drill bit.
I have filled the shocks with oil in lowest postion before connecting the lines. Also blead out the system. up to the shock connection. When i did this i was already 2.5 ltrs in before i filled up both side's what i think is a lot.
Also the suspension feels rock hard. I suspect that both sides the spring accumulator is not holding any nitrogen pressure any more. This also because when i turn the pump the car raising directly. normally you would expect some pressure build up in the spring accumulators. because the hold 23 bars.
The spring accumulators where also 2 that i had laying around. and are not new and i did not now the condition at all. I also tested the 2 flow reducers valves. If i close these complete the cars feels the same in the front also rock hard.
My custom adapters in the top connection of the shock absorbers also fit correct and don't have any leaks.
So what is next? i have to see if there are some things i need to fix before the engine will go out of the car and i can fix the engine bay. do some rust repairs and paint the engine bay. Also the engine needs to be cleaned and a partly rebuild. transmission needs check and valve body clean. So this is a very nice point in the build process
If there are any questions just ask
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Installing front hydraulic SLS suspension on the W124 S124 is a modification that i have not seen before.
The W124 is not factory availible. This was optional on the R129 and W201. The W201 system is pretty rare and to rare to use this parts. So in my install i using R129 parts. If the are availible. i have used oem R129 hydraulic shock absorbers. These are still new availible from the dealer
The hydraulic valves for control of the firmness or sport setting is to rare or to expensive to use. So im using industrial parts to controll this. If these parts fail in the future then the are easy to get and to change out. The level valve im using a OEM part. For controlling the level outside of the weight load adjustment. Im using aftermarket parts.
I have installed the system for the firmness adjustment on both front side of the car, These systems are installed on each side in the wheel arch. the firmness adjustment will have 2 base settings. comfort and sport. The base settings can be set with 2 valves that can reduce the flow of oil to and from the shock absorber to the spring accumulator.
If there are any questions just ask
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
500E fenders on the S124 V8 turbo
I did a lot of research the last weeks of what is the best to place parts on certain positions. This because the car needs to stay serviceable. I have placed the cooling water overflow tank as close as possible to engine firewall. So i can still place the battery in the front where the oem position is. but just 90 degree's difference
Because i'm going to change the front to 500E fenders on the S124 V8 turbo and also to hydraulic self leveling. I need space for the hydraulic components. There is no space in the engine bay of both side. Also not behind the first firewall. The best place is the in the open fender space. This also is giving the car not really visible different suspension system.
The bodykit i'm using for this project is a mbbodykits product. have a look on there website
mbbodykits.com
I ordered the new hydraulic parts. And the plan is to make a test setup to see how the car is going to react to the more and less oil in the struts.
If there are any questions just ask
JMSpeedshop !
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
Mercedes G63 AMG Designo 2013
This Mercedes G63 AMG Designo 2013 is just cool. let i start. that this is the first G-klasse i have every driven. And it is not bad at all. It has some weird bodyroll and very classic feel when cornering. But this is what it makes the difference to all the other cars on the market in this categorie.
All model from different brands look the same in big lines. This car stands out. It's a retromod. It never meant to be this but it became
The G wagon is in production from 1979 the chassis and body did not really change up to 2018. After this the car is just rebuild on everything you don't see on the outside.
This car is still the old chassis and body. Fitted with the M157 5.5 bi turbo V8 4 valves per cyl. producing 544hp and about 800nm. 0-100kph is possible in 5.4 sec. and this is a real life number because i hit below this already .
The car is limited at 210kph what i think is not strange because you need to correct the car more when you drive it hard. It is a 2450KG square box. but a very cool one.
The M157 engine can have some issue's so do your homework when your in the market for a car with this engine code here is a link
tuningpro.co/the-5-most-common-mercedes-m157-amg-engine-problems
But the car from the video has no issue's the chain and tensioner and parts are all renewed,
This car is for sale at https://henkgrooten.nl/aanbod/detail/16032631-awd-mercedes-benz-g-63-amg-designo-55-000-km.html
If there are any questions about this model or else just ask
MUSIC: MAXZWELL-READY
➤Patreon: patreon.com/jmspeeddshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
New update on the project. S124 V8 turbo
Have the inlet piping on the throttle body side also done. I have shortend the bend on the manifold because i needed more space for. Otherwise the connection and throttle body did not fit. Welded a fix connection on it and made a support on the piping that is bolted on the oil cooler plate.
Also installed the oil cooler lines and the oil thermostate. Final location is now on the driver side so the oil cooler for the transmission is moved to the passenger side.
The cooling lines for the radiator could not be used fro stock. it just did not fit. the bottom hose needed a T piece. Oem radiator from a S500 has a extra connection. That this radiator that i using from a W124 500e does not have. so i needed a T-piece. this water is now going to the outlet of the heater valves. This will also be the highest point. so the overflow cap will be here.
Going to leave the oem expansion tank. and go with an overflow type. so seperate tank for overflow and backflow. These will be placed in the space where normally the battery is located.
For the next part. I want to finish everything in the enginebay. So try to make list of want needed to be test fitted before the engine will go out for the last time
if there are questions just ask
JMSpeedshop
➤Patreon: patreon.com/jmspeedshop
➤Website: http://jmspeedshop.com
➤instagram: instagram.com/johanmuter
The Mercedes 450 SEL 6.9
This Mercedes 450 SEL 6.9 is a piece of history. The chance that mercedes build this large engine's again is practical 0 %. The W116 came on the market in 1972 up to 1980. In 1975 the 6.9 was avalible as the top off the range model.
In total 7380 Times build. From all the W116's build 473080 cars this is a Rare model. The 6.9 was standard a SEL and standard as the first mercedes equipped with hydro pneumatic suspension in the front and in the back. So fully self leveling. On the other W116 cars rear self leveling was optional.
The M100 engine came on the market in 1963 and is build up to 1981. This engine was first seen in the W108/W109 as the 300sel 6.3 but also in the W100 Mercedes 600. in 1975 the engine was overbored. From 6.3 to 6.9 by increasing the bore from 103mm to 107mm. The stroke stayed the same as 95mm.
This EU version had a CR of 8.8-1 in the rest of the world had 8.0-1 and was also a little less powerfull. @ 256HP. The EU version had 286HP @ 4250RPM and a massive 549nm @ 3000RPM. This was connected to a 722.003 3 speed automatic gearbox with a 2.65 LSD rear end.
And was capable of getting 0-100 kph in 7.4 Sec. Top speeds was 225kph but in real life it will hit 240kph easy. The fuel tank is 96ltr what is needed to give the engine enough fuel. The total weight is 1985kg .
Also have a on the website of Henk Grooten where this car is for sale
Also have alook in Mercedes/AMG playlist
If there are any questions just let me know


