EZ50 The pull line blowing tool. The very easy and fast way to get your pull line into a conduit Zeitler AG 2008-03-05 | Tedious and time-consuming cable and conductor pulling through installed conduits using fish tapes and steel wire is now a thing of the past! You can do the same job in minutes with the EZ50 pull line blowing to from Zeitler AGThe solution : Blow in a pull line with the patentedEZ-50 Stringing Gun. Simply insert the flexible connecting nozzle into the conduit and start. The pull line will whirl out of the other end of the conduit in a matter of seconds: you are now ready to start pulling. Even kinked conduits and flexible tubing with several tight bends present no problem for the EZ.50.The EZ-50 PULL LINE BLOWER (Stringing Gun) is light, compact and easy to use.Follow us on or Social Media Channels for more infos about pull line blowers.Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agLinkedIn: linkedin.com/company/zeitler-agAll our Pull Line Blowing Equipment are listed here:https://zeitler.ch/en/products/stringing-guns
EZ System 8 and The Pull Line Blower EZ100 Zeitler AG 2022-09-16 | Rolled up 200m and with lots of water :D
Next level fiber installation with the EZ15 pull line blower for microducts Zeitler AG 2021-11-10 | ...
Fastest Pull Line Blower with a parachute #shorts Zeitler AG 2021-03-19 | #shortsFast pull line blowing with the Zeitler EZ100
Fast and Easy Fiber blowing Tool #shorts Zeitler AG 2021-03-10 | #shortsFast and easy fiber installation with zeitler #fiberblowing fttx kit 1
EZ300 Pull Line Blower / Mule Tape Blower / Conduit Blower over distance of 1.1 Km Zeitler AG 2020-09-04 | The Pull Line or Mule Tape Blower EZ300 from Zeitler at work on a major construction site in Tallinn, Estonia.The EZ300 Mule Tape Blower or Conduit Rope Blower has many benifits.Blow or suck pull line (tensile strength up to 300 kg)without compressor• Independent of electric power supply• For all commercial pipe work(internal diameter from 25 to 200 mm)• For all network construction such as civil engineering,ground work, roads, tunnels, bridges, snow cannons,cable car construction, mountain railway• For lengths of 1000 m and more(current record 2’850 m)• Huge time saving in cable feeding• Cleaning, taking water out, calibrating and line feedingin one step• Lightweight and compact• Excellent accessibility, even in confined spaces• Easy to handle• Double function (blowing and suction mode)• Suitable in any car boot• Value for money Thank you for the video HÖHLE OÜProject: Replacing Tallinn, Veskimetsa-Kopli L161 with cable lineBuilder: LEONHARD WEISS GmbH & Co. KGPipe: 75 mmCut length: 1100 mTool: Zeitler EZ.300If you need more info or a demo in Estonia, Lithuania, Russia or Finland. Please contact:Margus MaasingMÜÜGIJUHT+372 514 7676margus.maasing@hohle.ee
Installation of Flat Drop Cable with pusher and power drill Zeitler AG 2020-07-28 | We got recently some requests from the USA to construct a setup for pushing flat drop cables with our EZ.Speedy into ducts for a #FTTH installation.So, we made something newAre you tired as well to push your flat drop cables manually into ducts?Do you want to save time, money and manpower?The new Tube/Ducts Coubling for our EZ.Speedy is the perfect tool for installation of flat drop cables with a cable pusher for you.The cable will not take any damage!Special thanks to OFS and Juergen Wittig for the flat drop cable.#telecominfrastructure #fiberoptics #fiberpushing #flatdropcable #cablelaying #cables #zeitler #ftts #fttx #fttb
Schnur einblasen um Glasfaser einzuziehen mit dem Schnureinzugsgerät EZ100 Zeitler AG 2020-01-30 | Enorme Zeitersparnis beim Glasfaser Kabeleinzug oder auch bei anderen Kabeln die in ein Rohr eingezogen werden müssen.Auch bei engsten Platzverhältnissen wie in kleinen Glasfaser Telekomschächten zu benutzen.Doppelfunktion einblasen von Zugschnur und ansaugen von ZugschnurEinblasen oder Ansaugen einer Kabel Einzugsschnur in alle handelsüblichen Kabelschutzrohre mit Innendurchmesser von 25 bis 150 mm (kein Kompressor ist nötig)Installationen von Kabeln im Kabelnetzbau sowie im Bereich von Erdreich/Strassen-, Tunnel- sowie Brückenbau im Handumdrehen ohne schweres Material zb eines grossen Kompressors in sehr kurzer Zeit möglich.Für weitere Infos zum Schnureinzugsgerät / Schnureinblasgerät EZ100 kontaktieren sie die Zeitler AG der Kabelverlege Spezialist aus der Schweiz.Hersteller von Schnureinblasgeräten und GlasfasereinschubgerätenZeitler AG6206 NeuenkirchSchweizTel: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: linkedin.com/company/zeitler-agFacebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agWeb: https://zeitler.ch/
Einblasen der Zugschnur bei Wasser gefüllten Rohren mit Schnureinzugsgerät / Schnureinblasgerät. Zeitler AG 2019-12-03 | In diesem Video sehen sie das auch das einblasen einer Zugschnur bei Wasser gefüllten Rohren kein Problem ist für die starken Schnureinblasgeräte / Schnureinzugsgeräte der Zeitler AG. Distanz des Schnur einblasen der Zugschnur war ca. 500m. Im Video kann man sehen wie viel Wasser das Schnureinzugsgerät EZ.300 ohne Probleme verdrängen kann.Hersteller:Zeitler AG 6206 NeuenkirchSchweizTel: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: linkedin.com/company/zeitler-agFacebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agWeb: https://zeitler.ch/en Schnureinblasgerät oder auch Schnureinzugsgerät zum belegen mit einer Zugschnur in Rohre.
Pull tape / line blower EZ.300 the distance of blowing was 500m in a remote area. Zeitler AG 2019-12-03 | The pull tape or pull line blower EZ.300 needs no electrical connection. The strong fuel engine feeds the pull line independent of a power supply.In the video you will see how powerful the line blower pushes water and residue out of the ducts.EZ300 conduit blower is used for network construction in civil engineering, ground work, roads, tunnels, bridges, snow cannons and cable car construction.Much more efficient than a fish tape, duct rods, conduit rods, duct rod pushers, duct rodderManufacturer:Zeitler AG6206 NeuenkirchSwitzerlandPhone: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: https://www.linkedin.com/company/zeit...Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agWeb: https://zeitler.ch/en#pullline #pulltape #construction #civil construction #lineblower #pullineblower #pulltapeblower #conduitblower
Smallest and Simplest fiber blowing machines used in Germany for the last mile of fiber blowing. Zeitler AG 2019-11-28 | Small, Simple and does the job. Like a SwissArmyKnife#fiberblowingmachine from Switzerland. Zeitler's FTTx Kit 1 fiberblowing ( fiberjetting )in Germany with LEONHARD WEISS GmbH & Co. KG Micro-Duct 7mm - Fiber 2.3 mm, if I remember it correctly. Distance blown 280mIf you need it simple and easy to use this is the fiberblowingmaschine you are looking for. No need to make expensive trips to learn how to to a fiber installation for the last my of fiber to the home ( #ftth )Manufacturer:Zeitler AG6206 Neuenkirch/LuzernSwitzerlandPhone: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: https://www.linkedin.com/company/zeit...Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agWeb: https://zeitler.ch/
Schnureinzugsgerät EZ50 der Zeitler AG auf der Baustelle um später Kabel einzuziehen. Zeitler AG 2019-11-22 | EZ.50 Schnureinblassgerät der Zeitler AG. Schnelles und Zeitsparendes Elektriker Zubehör um später Kabel einzuziehen und Kabel zu verlegen.Mit dem Schnureinzuggerät EZ50 von Zeitler wird eine Spezialschnur schnell und zuverlässig in handelsübliche Elektrorohre Ø 18 - 50 mm eingeblasen. Problemlose Anwendung auch bei gequetschten Rohren, Abzweigkästen, Dosen oder Lampendosen.ZEITLER AG stellt ein attraktives Sortiment an Schnureinblasgeräten her. Dank der verschiedenen Geräte und deren Zubehör wird Zugschnur in Rohrgrössen von Ø 4-200 mm (Innendurchmesser) eingezogen. Selbst deformierte oder belegte Rohre können noch mit Schnur bestückt werden. Mit diesen vorab eingeblasenen Schnüren können dann mühelos Kabel und Leitungen eingezogen werden.Mit den Geräten kann nicht nur Zugschnur sondern auch speziell entwickelte Ortungsschnur eingeblasen werden.Verkauf Deutschland:Primo GmbHprimo-gmbh.comGebrüder-Dickow-Straße 2 84478 Waldkraiburg +49 8638 88559-200+49 8638 88559-299info@primo-gmbh.comHersteller:Zeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandPhone: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: https://www.linkedin.com/company/zeit...Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agWeb: https://zeitler.ch/
Glasfaser LWL einblasen mit der kleinsten Glasfaser Einblass Einheit auf dem FTTx Markt Zeitler AG 2019-11-07 | Glasfaser einblasen Produkt Training für die Firma Cablex in der Schweiz.Das FTTx LWL Glasfaser Einblasen Kit 1 enthält alles, was Sie zum sanften, gleichmässigen Einblasen von LWL Kabeln (Ø 0.5 mm bis 8.0 mm) in Mikrorohre (Ø 6, 7, 8, 10, 12 und 14 mm) benötigen: EZ.SPEEDY (Glasfaser Vorschubeinheit) für die gewählte Glasfaser Kabeldimension, inklusive benötigtes Montagewerkzeug und KupplungstückEZ.BOOSTER (Glasfaser Blaseinheit) für die entsprechende KabeldimensionEZ.SPEEDY Montageblock, um die Geräte auf einem Stativ oder einer Werkbank sicher zu befestigenBOSCH Akku-Bohrschrauber GSR12V-15 inkl. LadegerätAlles zusammen im robusten EZ.Koffer, in dem auch weiteres Zubehör und Erweiterungen für zusätzliche Kabeldimensionen bequem und sicher verstaut werden können.Ihr Profi für Glasfaser KabelverlegetechnikZeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandPhone: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: https://www.linkedin.com/company/zeit...Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_ag
Fiber blowing to the home tool for the last fttx mile. Smallest Fiber blowing machine on the market Zeitler AG 2019-11-07 | Product Training @cablex / Switzerland for the Zeitler Fiber blowing machine.The FTTx Kit 1 fiber blowing equipment contains everything you need for gentle, even fiber jetting of fiber optic cables (Ø 0.5 mm to 8.0 mm) into microducts (Ø 6, 7, 8, 10, 12 and 14 mm):EZ.SPEEDY (fiber cable pusher) for the selected cable dimension, including the required assembly tool and coupling pieceEZ.BOOSTER (fiber blowing unit) for the corresponding fiber cable dimensionEZ.SPEEDY fiber blowing Mounting block to securely attach the devices to a tripod or workbenchBOSCH cordless drill / driver GSR12V-15 incl. chargerAll together in the heavy duty EZ.carry case, where additional accessories and upgrade-sets for further cable dimensions find a save place.More infos and prices you will find here:https://zeitler.ch/en/shop/2-kabeleinschubvorrichtung/02-im-all-in-koffer/10-fttx-kit-1Fiber Blowing machines byZeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandPhone: +41 41 467 16 14E-Mail: info@zeitler.swissLinkedIn: linkedin.com/company/zeitler-agFacebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_ag
Zugschnur einblasen in Flexrohr / Wellrohr Rolle mit Schnureinblasgerät EZ.15 Zeitler AG 2019-10-28 | EZ15, das perfekte Werkzeug zum Einblasen von Zugschnur in jegliche Art von Kabelschutzrohren (ø 4-20 mm).Schnureinblasen in Wellrohre, Flexrohre, Mikrorohre bis zu einer Länge von 500 m (Rolle bis 100 m).Ideal für den Großhandel. Reduzieren Sie ihren Lagerbestand. Sie können Leerrohre jederzeit auf Kundenwunsch mit Zugschnur nachrüsten. Schnell und einfach mit diesem Schnureinblasgerät bestücken.EZ15 Schnureinblasgerät für Mikrorohre (ø 4-20 mm).Komplettausstattung im robusten Kunststoffkoffer inklusive folgendem Zubehör:5 Rohranschlüsse für ø 6, 8, 10, 12 und 14 mm1 Rohranschlussadapter 8/7mm1 Druckluftschlauch (Länge 3 m)1 Universal-Schlauchaufsatz bis 20 mm1 Box mit Ersatzteilen, Schere1 T-Stück (zum einfachen Abheben des Deckels um Schnur nachzufüllen)4 Rollen Spezialschnur ø 1 mm (24 kg Zugkraft / Länge ca. 900 m)1 BedienungsanleitungZeitler AGSonnhalde 76206 Neuenkirch/LuzernSchweizTel: +41 41 467 16 14E-Mail: info@zeitler.swissWeb: https://zeitler.ch/de
Blowing pull line into 100 m / 300 ft long corrugated innerduct with EZ.15 pull line blower Zeitler AG 2019-10-24 | Use the EZ.15 from Zeitler AG to blow pull lines into Corrugated ducts, flexible conduits, indoor riser ducts, corrugated innerducts or any other ducts. Distances 100m on a roll (330 ft)Speedpipes and microducts for fiber optic cables are as well possible with even longer distances.EZ.15 is THE perfect tool for wholesale of corrugated ducts with pull line rope strings ready to use on construction sites.Visit, write or call usZEITLER AGSonnhalde 7CH-6206 Neuenkirch/LuzernSwitzerlandPhoneNational: 041 467 16 14International: +41 41 467 16 14E-Mail: info@zeitler.swiss
Specially engineered pull line made of 100 % Polyolefine by Zeitler AG Zeitler AG 2019-10-23 | Specially engineered pull line made of 100 % Polyolefine, paraffined (no water absorption), 2-ply double twisted,in 3 different strengths:Ø 1 mm , tensile strength 24 kg , about 900 m / rollØ 4 mm , tensile strength 210 kg , about 1100 m / roll (also available with meter marks)Ø 4 mm , tensile strength 300 kg 750 m / roll Delivered as coreless cylinder roll with internal flow. Therefore no risk of accident by jumping roll.The special pull line was developed specifically for use with the Zeitler pull line blowers but can be blown with conventional devices.Zeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandTel: +41 41 467 16 14E-Mail: info@zeitler.swisshttps://zeitler.ch/en/shop/3-schnur
Speziell entwickelte Zugschnur Produktion Zeitler AG Zeitler AG 2019-10-23 | Speziell entwickelte Zugschnur aus 100% Polyolefine, paraffiniert (nimmt kein Wasser auf), 2 fachdoppeltgezwirnt,in 3 verschiedenen Stärken:Ø 1 mm, Reissfestigkeit 24 kg, ca.900 m/RolleØ 4 mm, Reissfestigkeit 210 kg, ca. 1100 m /Rolle (auch metriert lieferbar)Ø 4 mm, Reissfestigkeit 300 kg, ca. 750 m /RolleDiese Spezialschnur wird als hülsenlose Spule mit Innenablauf geliefert. Unfälle durch herumspringende Spulen können so vermieden werden.Die Spezialschnur wurde speziell für den Einsatz mit den Zeitler Schnureinblasgeräten entwickelt, kann aber auch mit herkömmlichen Vorrichtungen eingeblasen werden.Zeitler AGSonnhalde 76206 Neuenkirch/LuzernSchweizTel: +41 41 467 16 14E-Mail: info@zeitler.swisshttps://zeitler.ch/de/shop/3-schnur
Fiber blowing the easy and fast way Zeitler AG 2019-05-02 | Around 300m fiber blowing in a very tight microduct to FTTPEZ.SPEEDY & EZ.BOOSTER & EZ.EASYGLIDE to the rescue.We needed all 3 of our tools to get the fiber optic cable blown into this very tight microduct.Fiber blowing with in this situation was only possible with our EZ.Booster & EZ.Easyglide to get the 300 meters of fiber into the conduct safely.Another word term btw for fiber blowing is fiber jettingFollow us for more Information on blowing fiber atFacebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter twitter.com/zeitler_agLinkedin: linkedin.com/company/zeitler-ag
Pull Line Blowing with EZ100 handover and introduction for Universal Elektrik in Switzerland Zeitler AG 2019-04-30 | Zeitler - The new definition of pull line feeding!EZ100 handover and introduction for Universal Elektrik in Switzerland.Pull Line Blowing the fast way! Distance 300m pullineblowing for later fiberoptic ftth fttc fttx insertion.The Stringing Gun EZ100 by Zeitler has been developed especially for network construction such as civil engineering, ground work, roads, tunnels, bridges, etc.It is suitable for cable ducts from Ø 50 to 150 mm (internal diameter).The pull line might be blown or aspirated. Water, small residues, impurities or else can often be pushed through with the shuttle in only one operation.Blow pull line (tensile strength up to 300 kg) without compressorFor all commercial pipe work (internal diameter from 50 to 150 mm)With special equipment also for small diameters from 25 mmFor all network construction such as civil engineering, ground work, roads, tunnels, bridgesFor lengths of 1000 m and more (current record 2’850 m)Huge time saving in cable feeding: Cleaning, taking water out, calibrating and line feeding in one stepLightweight and compactExcellent accessibility, even in confined spacesEasy to handle Double function (blowing and suction mode)Suitable in any car bootValue for moneyApplication (Short guide)Conduit ends must be clean and cut off evenlyFirstly, blow air trough the conduit without shuttle, check if penetrable tube/correct tubeAssemble shuttle correspending exactly to the Ø int. of tubeInsert pull line through pull line supply and knot it tightly to the shuttlePlace shuttle in the conduit and press EZ100 to the conduit, the front being movable for 360°Blow shuttle troug without interruptingAttach either cable/s or extra strong pull line and start pullingMore Info:https://zeitler.ch/en/products/stringing-guns/ez100Follow us un Social MediaFacebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agLinkedIn: linkedin.com/company/zeitler-ag
EZ300 Pull Line Blowing Tool Stringing Gun Zeitler AG 2019-04-15 | The Stringung Gun EZ300 is a pull line blowing tool by Zeitler AG It needs no electrical connection. The strong fuel engine is blowing the pull lineindependent of power supply.Infos and Price: https://zeitler.ch/en/products/stringing-guns/ez300The EZ300 is used for network construction in civil engineering, ground work, roads, tunnels, bridges, snow cannons and cable car construction.It is suitable for cable ducts Ø 25 to 200 mm (internal diameter).Water, small residues, impurities or else can often be pushed through with the shuttle in only one operation.Blow or suck pull line (tensile strength up to 300 kg) without compressorIndependent of electric power supplyFor all commercial pipe work (internal diameter from 25 to 200 mm)For all network construction such as civil engineering, ground work, roads, tunnels, bridges, snow cannons, cable car construction, mountain railway For lengths of 1000 m and more (current record 2’850 m)Huge time saving in cable feeding: Cleaning, taking water out, calibrating and line feeding in one stepLightweight and compactExcellent accessibility, even in confined spacesEasy to handle Double function (blowing and suction mode)Suitable in any car bootValue for moneyFollow us via:Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agLinkedIn: linkedin.com/company/zeitler-ag
Stringing Gun EZ15 Demonstration Pull Line Blowing Zeitler AG 2018-04-18 | The Stringing Gun EZ15 by Zeitler was especially designed for pull line blowing in micro-ducts Ø 4 to 20 mm (internal diameter) on short distances (up to 500 m).Infos: https://zeitler.ch/en/products/stringing-guns/ez15Zeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandPhone +41 41 467 16 14E-Mail: info@zeitler.ch
EZ.Speedy and EZ.Booster blowing fiber into microducts demonstration by Zeitler AG Zeitler AG 2018-02-01 | In Action: Our EZ.SPEEDY, EZ,BOOSTER in Action Infos at https://zeitler.ch/en/products/cable-feeding-tools #cablefeedingtools The perfect tool for blowing fiber optic cables (ø 0.5 mm to 8.0 mm) into micro-tubes. Connect the EZ.SPEEDY to a standard cordless drill and start blowing fiber optic cables quickly and safely (without bending) into micro-ducts.Insertion length up to 500 m.In connection with the EZ.BOOSTER the cable can be inserted even more smoothly and evenly.Tool for pressed air-aided insertion of fiber optic cables (diameter 0.5 mm to 8.0 mm) in micro-ducts. With the EZ.BOOSTER connected to a standard compressor you have a simple and easy way to feed fiber optic cables quickly and safely into micro-ducts. Insertion lengthup to 500 m.In combination with the EZ.SPEEDY performance can even be improved.
EZ.CASE Version 2 for your Cable feeding tools by Zeitler AG Zeitler AG 2018-02-01 | EZ.CASE Version 2 for your Cable feeding tools.Store your valuable EZ.TOOLS savely in our new EZ.CASE. More infos at our store at https://zeitler.ch/en/shop=======The ZEITLER AG manufactures an attractive assortment of pull line injectors. Thanks to the availability of different devices with the suitable accessories, pull lines may be inserted into pipes from Ø 4-200 mm (inner diameter). Even misshapen or coated pipes can be outfitted with cables. These injected pull lines make it easy to insert cables, wires and pipes.The market requirements are in constant flux, and we move with the markets. We adjust the developments of our devices to the latest customer requirements.Therefore, we focus on the direct cable insertion in the FTTX market. The EZ.SPEEDY and EZ.BOOSTER put a compact and very efficient cable injector system into your hands. Customers use the handy devices to insert fiber bundles and micro cables (ø 5 - 8.0 mm) into micro cable conduits quickly and easily. They are ideal tools specifically in building network installations. Cable insertions up to 500 meters are possible. Even the installation of the 'last few meters' from the basement to the individual apartments proceeds without much effort.The cable lubricator EZ.EASYGLIDE facilitates the EZ.SPEEDY and EZ.BOOSTER actions. In no time at all, the lubricator coats cables efficiently with a thin layer of lubricant.NEW - Divisible Cable feeding tool EZ.SPLITDo you want to insert fiber optic cables in two directions from a single chamber? Do you want to avoid splicing by installing ready-made FTTH terminal boxes? No problem! It will be child's play with the EZ.SPEEDY in combination with the EZ.SPLIT.Ready to use within secondsNo need for special trainingFast, easy and safeCurious? Get in touch with us!
EZ.CASE Version 1 for your Cable feeding tools by Zeitler AG Zeitler AG 2018-02-01 | EZ.CASE Version 1 for your Cable feeding tools.Store your valuable EZ.TOOLS savely in our new EZ.CASE. More infos at our store at https://zeitler.ch/en/shop=======The ZEITLER AG manufactures an attractive assortment of pull line injectors. Thanks to the availability of different devices with the suitable accessories, pull lines may be inserted into pipes from Ø 4-200 mm (inner diameter). Even misshapen or coated pipes can be outfitted with cables. These injected pull lines make it easy to insert cables, wires and pipes.The market requirements are in constant flux, and we move with the markets. We adjust the developments of our devices to the latest customer requirements.Therefore, we focus on the direct cable insertion in the FTTX market. The EZ.SPEEDY and EZ.BOOSTER put a compact and very efficient cable injector system into your hands. Customers use the handy devices to insert fiber bundles and micro cables (ø 5 - 8.0 mm) into micro cable conduits quickly and easily. They are ideal tools specifically in building network installations. Cable insertions up to 500 meters are possible. Even the installation of the 'last few meters' from the basement to the individual apartments proceeds without much effort.The cable lubricator EZ.EASYGLIDE facilitates the EZ.SPEEDY and EZ.BOOSTER actions. In no time at all, the lubricator coats cables efficiently with a thin layer of lubricant.NEW - Divisible Cable feeding tool EZ.SPLITDo you want to insert fiber optic cables in two directions from a single chamber? Do you want to avoid splicing by installing ready-made FTTH terminal boxes? No problem! It will be child's play with the EZ.SPEEDY in combination with the EZ.SPLIT.Ready to use within secondsNo need for special trainingFast, easy and safeCurious? Get in touch with us!
Zeitler AG pull line feeding equipment at the EXPO Energietechnik 2017 Zeitler AG 2017-06-23 | Zeitler AG pull line feeding equipment at the EXPO Energietechnik 2017 in Niederurnen, Switzerland.30 sec walkaround. Check out our re-sellers. There are severalMore Info about us at: https://zeitler.ch/en
ZEITLER AG DAY 2 ANGACOM 2017 with the EZ Booster and EZ Speedy Zeitler AG 2017-06-11 | Zeitler - your expert for cable laying techniques!More infos about the EZ Booster and EZ Speedy Systemhttps://zeitler.ch/en/products/cable-feeding-tools
Walkaround Angacom 2017 with Zeitler AG Zeitler AG 2017-06-11 | A quick walkaround at the Angacom 2017Who ist Zeitler AG ?https://zeitler.ch/enFeeding pull line or direct cable insertion?Zeitler AG produces an attractive range of pull line feeding equipment. Thanks to our different types of Stringing Guns and their accessories, we cover the range of conduits from Ø 4-200 mm (internal diameter) . Even deformed or occupied conduits may be feeded with pull line. The special pull line makes it easy to install cables and wires. The market is continuously developing, customer needs changing. We look ahead to keep our equipment and accessories up-to-date to customer requirements. That's why we also rely in direct cable feeding for FTTX applications. Fiber optic bundles and cables ( Ø 0.5-8.0 mm) may be feeded directly in a simple but efficient way aided by a cordless drill and/or pressed air. Ideal tools specifically in building network installations. Cable insertions up to 500 meters are possible. The installation of the 'last few meters' from the basement to the individual apartments proceeds without much effort or specific training.The cable lubricator EZ.EASYGLIDE facilitates the EZ.SPEEDY and EZ.BOOSTER actions. In no time at all, the lubricator coats cables efficiently with a thin layer of lubricant.
Blowing Fiber with EZ SPEEDY and EZ BOOSTER into microducts Zeitler AG 2015-12-07 | Simple Fiber installation with our EZ Fibre Blowing Tools. EZ SPEEDY and EZ BOOSTERBlowing fiber in microducts with high quality products from Zeitler AG based in Switzerland.EZ BOOSTER: Tool for pressed air-aided insertion of fiber optic cables (diameter 0.5 mm to 8.0 mm) in micro-ducts. With the EZ.BOOSTER connected to a standard compressor you have a simple and easy way to feed fiber optic cables quickly and safely into micro-ducts. Insertion lengthup to 500 m.In combination with the EZ.SPEEDY performance can even be improved.EZ SPEEDY:The perfect tool for feeding fiber optic cables (ø 0.5 mm to 8.0 mm) into micro-tubes. Connect the EZ.SPEEDY to a standard cordless drill and start feeding fiber optic cables quickly and safely (without bending) into micro-ducts.Insertion length up to 500 m.In connection with the EZ.BOOSTER the cable can be inserted even more smoothly and evenly.For more Information and how our tools perform for blowing fiber into microductsContactZeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandPhone +41 41 467 16 14E-Mail: info@zeitler.chWeb: https://zeitler.ch/enLinkedIn: linkedin.com/company/zeitler-agFacebook: facebook.com/Zeitler.AGIG: instagram.com/zeitler.agTwitter: twitter.com/zeitler_agAbout Zeitler AGWe focus on the direct cable insertion in the FTTX market. The EZ.SPEEDY and EZ.BOOSTER put a compact and very efficient cable injector system into your hands. Customers use the handy devices to insert fiber bundles and micro cables (ø 5 - 8.0 mm) into micro cable conduits quickly and easily. They are ideal tools specifically in building network installations. Cable insertions up to 500 meters are possible. Even the installation of the 'last few meters' from the basement to the individual apartments proceeds without much effort.The cable lubricator EZ.EASYGLIDE facilitates the EZ.SPEEDY and EZ.BOOSTER actions. In no time at all, the lubricator coats cables efficiently with a thin layer of lubricant.Zeitler AG, founded in 1957, has changed from a traditional contract manufacturer to a producer of innovative Stringing Guns and cable laying tools. Developed due to difficulties at construction sites, the extremely helpful Zeitler Stringing Guns became invaluable tools for electrical installers and construction companies.This shows once again how important it is to record customer problems and needs. The result was to develop step by step a range of products for each installation area. The equipment can be used for ducts from Ø 4 to 200 mm (internal diameter). The days of heavy equipment, only transportable in trucks or trailers, are gone.Today, handy equipment, suitable in any car boot, is the constant companion of electrical installers and piping professionals.Customer requirements and individual conveniences are thoroughly recorded and put into practical solutions whenever possible. Thus, the range of accessories has grown and shows now various auxiliary tools and parts for several solutions. Meanwhile, Zeitler AG is represented in several countries. Constantly new representatives around the world join our distribution network.
EZ SPEEDY EZ BOOSTER Kabelschubvorrichtung zum LWL Kabel einschieben Zeitler AG 2015-12-07 | Vorrichtung zum druckluftunterstützen Einschieben von LWL Kabeln (ø 0.5 mm bis 8.0 mm) in Mikrorohre. Mit dem EZ.BOOSTER können mit Hilfe eines handelsüblichen Kompressors LWL-Kabel schnell und sicher in Mikrorohre eingeschoben werden. Einschublänge bis ca. 500 m. In Kombination mit dem EZ.SPEEDY kann die Leistung sogar noch verbessert werden.EZ SPEEDYVorrichtung zum maschinell-unterstützten Einschieben von LWL Kabeln (Ø 0.5 mm bis 8.0 mm) in Mikrorohre. Mit dem EZ.SPEEDY können mit Hilfe eines handelsüblichen Akkuschraubers LWL-Kabel schnell, sicher und ohne abknicken in Mikrorohre eingeschoben werden. Einschublänge bis ca. 500 m. In Kombination mit dem EZ.BOOSTER kann das Kabel sogar noch sanfter und gleichmässiger eingeschoben werdenZeitler AG Online Shop: https://zeitler.ch/de/produkt/kabeleinschubgeraeteZeitler AGSonnhalde 76206 Neuenkirch/LuzernSwitzerlandPhone +41 41 467 16 14E-Mail: info@zeitler.chWeb: https://zeitler.ch/enLinkedIn: https://www.linkedin.com/company/zeit...Facebook: facebook.com/Zeitler.AGIG: instagram.com/zeitler.agTwitter: twitter.com/zeitler_ag
EZ300 Das Schnureinblasgerät zum effizienten Schnur einblasen in ein Rohr. Zeitler AG 2013-01-15 | Das Schnureinblasgerät EZ300 von Zeitler braucht keinen Elektroanschluss. Mit dem leistungsfähigen 2-Takt-Motor wird die Einzugschnur stromunabhängig eingeblasen oder angesaugt.Schnureinblasen effizient und Leistungsstark Zum Einsatz kommt das Gerät im Bereich Tunnel-, Erdreich/Strassen- sowie Brückenbau, Bergbahnen und Seilbahnbau.Es eignet sich für Kabelschutzrohre Ø 25 bis 200 mm (Innenrohrdurchmesser).Wasser, loser Schmutz oder Kleinteile werden im gleichen Arbeitsgang ausgestossen.Schnur Einblasen oder Ansaugen einer Einzugsschnur (bis Zugfestigkeit 300 kg) ohne KompressorStromunabhängig dank 2-Takt-Motor Für handelsübliche Kabelschutzrohre (Rohrinnendurchmesser von Ø 25 bis 200 mm)Bei Installationen im Wohn-, Gewerbe- und Industriebauten, Erdreich/Strassen-/Tunnel-/Brückenbau, Seilbahnbau und BergbahnenEinzuglängen auch über 1'000 m (aktueller Rekord 2850 m)Grosse Zeitersparnis beim Kabeleinzug:Reinigen, Wasser ausstossen, Kalibrieren und Schnureinziehen in einem ArbeitsgangKompakte GeräteabmessungenHervorragende Zugänglichkeit, auch bei engsten PlatzverhältnissenLeicht und handlichEinfache GerätebedienungPasst in jeden KofferraumAusgezeichnetes Preis-/LeistungsverhältnisLeerrohr Schnur einblasenWebseite: https://zeitler.ch/de/produkt/schnureinblasen/ez300Folge uns auch auf: Facebook: facebook.com/Zeitler.AGInstagram: instagram.com/zeitler.agTwitter twitter.com/zeitler_agLinkedin: linkedin.com/company/zeitler-ag
EZ15 Zugschnur in 50m Rohrrolle einblasen. Zeitler AG 2012-06-01 | Das Schnureinzuggerät EZ15 von Zeitler wurde für LWL Anwendungen entwickelt. Es eignet sich speziell für den Schnureinzug bei kurzen Distanzen in Mikrorohre von Ø 4 bis 20mm (z.B. von Verteilerkasten in Wohnraum). Mit bis zu 1000 m/Minute wird die Spezialschnur in das Rohr geblasen.The Stringing Gun EZ15 by Zeitler was especially designed to feed pull line into micro-ducts Ø 4 to 20 mm (internal diameter) on short distances (e.g. junction box to home). With up to 1000m/minute the pull line finds its way through the duct.La pistola pasa-cables EZ15 de Zeitler ha sido desarrollada para insertar hilo tira-cables en micro-tubos de Ø interiores de 4-20 mm, sobretodo para distancias cortas (p.e. de la caja de distribución a la casa). Con hasta 1000 m/minuto el hilo tira-cables pasa por el micro-tubo.
EZ15 3 Zeitler AG 2011-08-24 | Das Schnureinzuggerät EZ15 von Zeitler wurde für LWL Anwendungen entwickelt. Es eignet sich speziell für den Schnureinzug bei kurzen Distanzen in Mikrorohre von Ø 4 bis 20mm (z.B. von Verteilerkasten in Wohnraum). Mit bis zu 1000 m/Minute wird die Spezialschnur in das Rohr geblasen.The Stringing Gun EZ15 by Zeitler was especially designed to feed pull line into micro-ducts Ø 4 to 20 mm (internal diameter) on short distances (e.g. junction box to home). With up to 1000m/minute the pull line finds its way through the duct.La pistola pasa-cables EZ15 de Zeitler ha sido desarrollada para insertar hilo tira-cables en micro-tubos de Ø interiores de 4-20 mm, sobretodo para distancias cortas (p.e. de la caja de distribución a la casa). Con hasta 1000 m/minuto el hilo tira-cables pasa por el micro-tubo.
