#35 Ice ScarifierFrom Steel To Wood2026-11-17 | #35 Ice Scarifier#287 Tractor ChallengeFrom Steel To Wood2023-08-06 | I've been invited to share my favorite add-ons on my tractor. Here they are! Now inviting: Glen → youtube.com/@timberterra Jason → youtube.com/@OakMountainAcotts#286 Digging a Ditch, Dump Trailer & More!From Steel To Wood2023-07-30 | I dug this ditch last year, but without a light slope, it's hard to maintain using the lawn mower or even the offset flail mower. So I remove dirt to have the desired slope. Moreover, I need a significant amount of dirt for the next project (wife's project!).
Let's put the new dump trailer in action!#285 New Dump TrailerFrom Steel To Wood2023-06-27 | I need a dump trailer, but I don't have time to make one... So the project is to update the hydraulic valve to have a float position#284 End of Logging SeasonFrom Steel To Wood2023-05-09 | Bucking and splitting firewood, which marks the end of the logging season of 2023.#283 Summer Is Here!From Steel To Wood2023-04-15 | Here is a quick update of the most recent project. Heating the pool! I've installed a titanium heat exchanger (salt water needs titanium over stainless steel). It's a 360k BTU heat exchanger. It's well suited for our pool. We've gained almost 40°F in 24 hours. Yes, the water was just above the freezing point, to begin with.#282 Snow Groomer UpdatesFrom Steel To Wood2023-02-28 | I've done a few updates on the snow groomer but never showed the improvements in a video. I take advantage of the few inches we got to make that video!#281 Roller, Boiler and Wood Stack UpdatesFrom Steel To Wood2023-02-21 | This is an update on the roller in daylight, the boiler burning green wood (and why), and the logging season 2023 so far.#280 Excavator UpdatesFrom Steel To Wood2023-02-17 | Here is an update of the modification I did on the excavator.#279 The Snow RollerFrom Steel To Wood2023-02-06 | I make a snow roller to maintain the trails. It has nothing to do with a lawn roller, being 42 inches in diameter, it can efficiently roll through a thick layer of snow. I use salvaged 11R22.5 wheels to make that contraption.#278 Plowing with an Excavator? Of course!From Steel To Wood2023-01-29 | Is an excavator any good in snow? I am hooking the snowplow I use with the tractor using the SSQA adapter. The snowplow is 7ft wide and the KX40 can handle it very well! I take advantage of the long arm to reach the top of the snow bank to knock it down. I also offset the turret to push the windrow further.#277 Heating Coil InstallFrom Steel To Wood2023-01-23 | Last video about the boiler. I install the heating coil into the furnace in the garage.#276 The Boiler - Part 2From Steel To Wood2023-01-11 | Part 2: That is a view from the inside of the building heating installation#275 Outdoor Wood BoilerFrom Steel To Wood2023-01-10 | Part 1: I explain the main features of the Sequoia Boiler.#274 Wood Shed Completion & Boiler StartupFrom Steel To Wood2022-12-06 | This is a quick overview of the woodshed completion and the boiler being started.#273 Wood Shed - Part 2 → Install TrussesFrom Steel To Wood2022-11-22 | Installing trusses has never been so easy using an excavator and pallet forks!#272 Wood Shed - Installing Trusses Using an ExcavatorFrom Steel To Wood2022-11-08 | In part 2 of the woodshed, I install trusses using my KX40 excavator. I have the forks set on the excavator and I assembled the trusses in pairs so they can stand alone on the beams.#271 Wood Shed - Making TrussesFrom Steel To Wood2022-11-04 | I make my own trusses for the wood shed. It's not that complicated, just takes some time. *** Special thanks to Mike for his precious help!
Also, a special thanks to this video from "flyboyslc1". It was my inspiration youtube.com/watch?v=Hfy6xL1V2zo#270 Wood Shed - Concrete PadFrom Steel To Wood2022-10-25 | In this episode of the wood shed build, I pour the concrete base for the outdoor wood boiler.#269 Wood Shed Build - Setting the PostsFrom Steel To Wood2022-10-18 | I just began the construction of the 20x30 wood shed to host the outdoor wood boiler. It will be a pole barn-style construction. In this video, I use the log crane trailer to set the post and it works very well.Inground Pool Installation - TimelapseFrom Steel To Wood2022-08-26 | We've managed to save a few videos to show the progression of the project.Our Latest Project - What Kept us BusyFrom Steel To Wood2022-08-26 | Here is an update on our latest project. That is an inground pool, which was on my wife's list for years. I could no longer justify postponing this project, since we have the perfect spot for it, not counting I have to get good use of that KX40 excavator too!#266 SSQA Conversion for Mini Excavator KX040 → Log GrappleFrom Steel To Wood2022-07-30 | In this video, I make a SSQA conversion for my mini excavator KX040, so I can use a log grapple otherwise used with my tractor. I'll get a good use of it with pallet forks also.
My hydraulic quick connect on my KX040 is made by Atelier Tétrault-Théberge, a local company. So I bought the "ears" from them, so I save myself a lot of time to replicate the conecting ears. ateliertt.ca
The last project Dave and I did together (so far...) youtube.com/watch?v=r65RvV05gx8#261 Franconia Notch ParkwayFrom Steel To Wood2022-03-12 | Franconia Notch Parkway in New Hampshire. Interstate I93 One of my favorite scenic routes!#260 Wood Storage RackFrom Steel To Wood2022-03-08 | For the woodshop, I need a storage system for all the wood planks and panels. A cantilever rack is best suited for that. Although it can be made of wood, steel is also a good option!#259 Mezzanine, Platform, or Catwalk?From Steel To Wood2022-03-03 | Is that a mezzanine, a platform, or a catwalk? It does not matter as far as I can reach the boxes on the top shelves safely!#258 Canam Defender HD10 Plowing Snow & Windrow ManagementFrom Steel To Wood2022-02-22 | This is how I manage to clear snow on a surface equivalent to more than 1-acre between the driveway, the parking lot, and the buildings. I use a homemade snowplow and the trusty Canam Defender HD10.
Is a UTV really capable of clearing snow? Judge by yourself!#257 Update → Woodworking ShopFrom Steel To Wood2022-02-17 | More than a year after moving to our new place, I finally set up the woodworking shop! I've shown in a previous video the light fixtures I replaced with LED. I've added 120V circuits for the tools in the middle of the place. Then I run pipes for dust collection.
The final touch was to get a decent tool chest...#256 Collecting Wood - Farma 3.8 Log Trailer In The SnowFrom Steel To Wood2022-02-08 | We are getting a bit too much snow for logging - for me. So this is the last day of collecting wood in the forest with the Farma 3.8 log trailer along with the Canam Defender HD10.
Nothing special except for the beauty of being out in the woods!#245 WoodWorking ShopFrom Steel To Wood2022-01-21 | I've been willing to set up my woodworking shop since we moved in... but so many projects came earlier on the list! That is a project I will do when the weather is not good for logging.#254Garage Lift #ShortFrom Steel To Wood2022-01-15 | Here is my new garage lift! Works great for ATV. Not so great for cars though...#253 Tractor Step For The Case 430From Steel To Wood2022-01-10 | This is not easy to climb on the Case 430. Even worst when wearing chainsaw safety pants in wintertime! So I decided to make a step to it.
That is not only a creature's comfort thing but also a safety issue.#252 Updates on the Small Case - 1965 Case 430From Steel To Wood2022-01-05 | I complete some updates on my new (to me!) 1965 Case 430. I redo most of the wiring of the machine, add lights, flashers, horn, seatbelt and extinguisher.
One more update in part 2!#251 Taking Care of the BucketFrom Steel To Wood2022-01-01 | I had to replace a tooth on the Kubota KX040 bucket. While replacing it, I change to a different style of teeth, better suited for rock and stumps. While having the bucket on hand, I take time to paint it the right color.
I could not resist, but paint something else while I was there.
Needless I did not paint over existing grease. So a MAJOR cleanup of the machine was in order. Cleaning in detail too!#250 Playing With The Excavator - Leveling TrailFrom Steel To Wood2021-12-23 | We have a trail we like riding with the UTV where it is out sloped. Way too much for being comfortable to ride. My wife hates that part of the trail. This was a good reason for getting an excavator I guess...
I am removing material on the inside to add on the outside. So I get a level trail. There is not much water coming down at this place, so I don't need to care about ditches or anything similar to redirect water.
This was the very last time to play in the dirt with the excavator before winter gets in full swing here.#249 Removing Stump - Last Chance Before WinterFrom Steel To Wood2021-12-20 | Last time to remove this stump before winter hits us! This stump is on the side of my driveway. I've hit it once with my snowplow last winter. This won't happen again!#248 Logging Season Is OpenFrom Steel To Wood2021-12-15 | This is the first time I use the Farma 3.8 log trailer for logging. This is a very productive tool that saves many steps.
Now that the ground is frozen, this is the best time of the year for logging. No mud, no mosquitoes, no ticks, etc. Then the trails are frozen enough to support the weight of the UTV and the log trailer. No mud on the logs either!#247 New Tools In The Garage! (Turning Discs Brakes)From Steel To Wood2021-12-11 | I've been maintaining brakes on my vehicles for a long time and was always annoyed the disc should be replaced so frequently. I found a disc lathe on Marketplace that will do the job. The machine paid for itself machining 4 discs!!!
Then I try a new device to lift the cars. Airbag jack. This will be useful when we change winter tires (wheels) to summer tires. We have 6 cars here that need the tire change twice a year! So better be equipped for lifting vehicles quickly and safely.#246 Is This Too Soon For A Christmas Gift?From Steel To Wood2021-11-30 | The project is to widen the parking lot about 15ft wider. This is not to park more cars, but rather to put firewood pallets on this parking pad, so there won't be grass growing between the pallets. Then this will let dry the wood even better, with fewer bugs/mice in it.
See our new equipment for that task!#245 Short → Can-Am 100hrs ServiceFrom Steel To Wood2021-11-09 | No project today... just a quick view of the BRP / Can-Am dealership I visited in Valcourt (Quebec, Canada). This is Performance NC of Valcourt. This is about 20 miles / 30km from where I live.
This 100hrs service was basically an oil change and an overall inspection. Plus there were 3 software updates to be made on it. There was a recall for the Defender HD10 for the CVT belt air inlet. Turns out the recall is only applicable for those who use tracks in the snow...
Anyways, BRP is the manufacturer of Ski-Doo, Sea-Doo, which are made in Valcourt. Valcourt is where it all started for Bombardier Recreative Products (BRP). Can-Am is also a brand of BRP but is not made in Canada as I understand.
Enough "talking"...#244 #short KubotaFrom Steel To Wood2021-11-03 | A visit to the Kubota dealership...#243 Log Trailer for Property MaintenanceFrom Steel To Wood2021-10-12 | I use the Farma C3,8D log trailer for property maintenance. I cut large limbs from trees around the hayfield and bring them to a pile in the forest. I use the Stihl pole saw HT-56 C-E to reach the high limbs. As usual, the Canam Defender HD10 is up to the task!
Deers really like having piles of branches in the wood to hide.#242 Installing Pallet Racks OutsideFrom Steel To Wood2021-10-04 | In the quest for more room in my 32x48' hangar, I manage to install pallet racks outside. Will it pass the freeze and thaw test? We will see that in 6 months!#241Trailer parkingFrom Steel To Wood2021-09-22 | I have a nice area between the hangar and the garage. Only problem, it's packed with stuff and a big pile of crushed stones in the middle. Not easy to clear snow in winter trying to maneuver around obstacles.
I make a reorganization of the stuff and spread the crushed stone pile.