An Engineers FindingsIn this episode I share some thoughts behind the design of my latest shop made tools and show how they are used. Among them are a short taper comparison gauge, a threading or tapping adapter with friction clutch for the milling machine, an oxy-acetylene cart and a quite universal chamfering tool.
0:00 Intro 1:20 Short Taper comparison Gauge 5:54 Threading or tapping Adapter 14:50 Oxy-Acetylene Cart 18:07 Chamfering Tool
New Machine Shop-made ToolsAn Engineers Findings2021-12-11 | In this episode I share some thoughts behind the design of my latest shop made tools and show how they are used. Among them are a short taper comparison gauge, a threading or tapping adapter with friction clutch for the milling machine, an oxy-acetylene cart and a quite universal chamfering tool.
0:00 Intro 1:20 Short Taper comparison Gauge 5:54 Threading or tapping Adapter 14:50 Oxy-Acetylene Cart 18:07 Chamfering ToolAction 76 - Adventure in the AlpsAn Engineers Findings2022-05-17 | This film originates in the years 1976 and 1977, in course of my [Rudolf Fillafer's] employment with the Austrian Federal Office of Metrology and Surveying. Our task was correcting the survey canvass and merging it with the Italian one. The Austrian Air Force assisted with Alouette 3 helicopters in the arising transport problems in the high-Alpine areas and contributed to a quicker completion of the job.
Copyright: Rudolf Fillafer Narrator: Werner Freudenberger Digitization: Werner Pinter Music: Neil Diamond, Pink Floyd, MantovanniMachining a Dividing Heads Worm Wheel ReplacementAn Engineers Findings2021-05-24 | The worm screw in my trusty Walter UTA 100E dividing head was damaged by corrosion, which in turn did wear down it's originally installed worm wheel. In the previous episode I managed to recondition the worm by thread grinding. It's lands thereby became slightly narrower. In this present follow-up episode, a new replacement worm wheel is made, designed specifically to fit the reground worm screw. I show how I designed and grind the necessary single point cutter and inspect it on the Nikon profile projector. The worm wheel blank is turned on my EMCO V13 lathe. The worm wheel teeth are machined on the Mikron WF-1 mill in an improvised setup, using the dividing head in question to hold the blank and my Wild-Heerbrugg T2 theodolite as an angular standard. Finally, the accuracy of the worm wheel replacement and the reground worm screw are tested by using the theodolite. The video ends with a discussion of the testing results. The reconditioned worm drive is now probably as good as new and ready for another 50 years of service!Regrinding a Hardened Dividing Head Worm ScrewAn Engineers Findings2021-02-27 | The worm screw in my trusty Walter UTA 100E dividing head was damaged by corrosion, which I didn't notice until I recently checked it's indexing accuracy. This worm is dead hard and the corrosion quite deep, so reconditioning is probably only possible by grinding. However, grinding that worm screw is not as straight forward as cutting threads on the lathe. So I came up with a grinding setup that borrows some parts of my Deckel D-bit grinder. This setup is used on my EMCO V13 lathe. Also I had to figure out particular angles and the necessary lead screw gearing ratio, avoiding rare gears which I don't have. The reconditioned worm is now probably as good as new and ready for another 50 years of service!Clinometer Reconditioning: Testing AccuracyAn Engineers Findings2021-01-01 | This video shows how I use an improvised setup to test the accuracy of my 1966 made Avimo Clinometer, aka. gunners quadrant. I bought this tool recently and had to recondition it by hand scraping, because once in it's lifetime it was dropped, which caused it's frame to distort. To test it's accuracy, I made a receiver plate to be held in my Walter UTA dividing head. This plate is machined and hand scraped, of which footage is included in the video. The receiver plate also holds the testing standard, which is my beloved Wild-Heerbrugg T2 theodolite. For testing, the latter is targeted on a fixed reference (here a mountain farmer's window), and then the horizontal circle is read. The results show that this clinometer's precision is better than 1.75 arc minutes.110 Kilovolts arcing Ground Fault behind the HouseAn Engineers Findings2020-12-07 | Some video footage and images of an arcing ground fault of a 110 Kilovolt power line behind our house in upper Carinthia, Austria, on 6th of December, 2020. This fault was caused by the wet snow which froze to the power lines. This added weight dragged that particular line far enough down to create a ground fault with an ash tree.Hints on Spindle Bearing AdjustmentAn Engineers Findings2020-11-01 | Some Hints on the theory and practice of adjusted bearing arrangements, or adjusted bearing spindles. With emphasis on preload determination and some practical aspects of setting a particular preload. The spindle in the video is my newly designed and built, highly flexible and compact welding positioner (rotary welding table).Dividing Head Accuracy: Unconventional TestingAn Engineers Findings2020-05-17 | In this video I use my arc-second accurate Wild-Heerbrugg T2 theodolite to test the accuracy of angular division of my trusty Walter UTA 100E universal dividing head. This is an easy, but probably unconventional procedure since usually angular standards or gauges are used to test dividing heads.Hints on making Straight Edges out of SteelAn Engineers Findings2020-04-25 | This video contains a selection of hints on making custom, precision straight edges out of carbon steel. I created this video because of recurring viewer questions about my 1.2 meters or 4 foot precision straight edge, which is featured in the video. It was almost exclusively made with basic hand tools. It is not made from cast iron as classic straight edges are, but rather it is a welded design out of three pieces of carbon steel.Prototype Press Brake: Setup, Tools and Bending WorkAn Engineers Findings2020-04-21 | This video shows the initial setup of my 40 ton force and 1.2 meters (or 4 foot) span prototype press brake, which I designed and built in 2018. Also some of the insert tooling I use is shown and explained. The video ends with a commented sample bending job to show how this press brake is used.Threading Dial Indicator for Metric AND Imperial ThreadsAn Engineers Findings2020-04-20 | A video about the extended threading dial indicator which I designed and built for my EMCO V13 lathe, to speed up the thread cutting process. What's special about this indicator, is that it works with metric AND imperial threads, while it doesn't require any drive gear changes. Also this video contains a discussion about the threading dial indicator theory, with particular emphasis on the differences between it's use with metric and imperial pitch lead screws and threads.The bizzare World of the TIG-Welding ElectrodeAn Engineers Findings2020-03-31 | An audio commented slideshow of scanning electron microscope (SEM) images of new and used tungsten (TIG) welding electrodes. SEM images captured by Dr. mont. Zhonghua Wang, Institute of Materials Science, TUM. Equipment kindly provided by Prof. Dr. mont. habil. DDr. h.c. Ewald Werner, Institute of Materials Science, TUM.Pre-Ignition or Backfire in Combustion Engines: A new Approach?An Engineers Findings2019-12-05 | An explanation and demonstration of parasitic spark pre-ignition, which is a problem that can be encountered in spark-ignited combustion engines. I couldn't find explanations about this process in textbooks yet, so allow me to call it "parasitic spark pre-ignition". The result of this process is sometimes called a "pre-firing", "backfiring" or "misfiring" engine. I became aware of this process during a tough, developmental troubleshooting on the GTP-13's custom, high compression ratio, AFR-controlled, 364 cubic inch, all-aluminium Ford Windsor-based dry-sump engine. The troubleshooting led to a neat solution and a now very nicely and reliably behaving engine. More information about the GTP-13 supersportscar at: www.gtp13.comWelding Distortion Explained Part 4: Influencing DistortionAn Engineers Findings2018-12-28 | Final part of a four part video series focusing on welding distortion.
Equipment and samples kindly provided by Prof. Dr. Dr.h.c. Ewald Werner, Institute of Materials Science, TUM.Welding Distortion Explained Part 3: Flame StraighteningAn Engineers Findings2018-12-28 | Part 3 of a four part video series focusing on welding distortion.
Equipment and samples kindly provided by Prof. Dr. Dr.h.c. Ewald Werner, Institute of Materials Science, TUM.Welding Distortion Explained Part 2: Stresses and StrainsAn Engineers Findings2018-12-28 | Part 2 of a four part video series focusing on welding distortion.
Equipment and samples kindly provided by Prof. Dr. Dr.h.c. Ewald Werner, Institute of Materials Science, TUM.Welding Distortion Explained Part 1: PrinciplesAn Engineers Findings2018-12-23 | Part 1 of a four part video series focusing on welding distortion.
Equipment and samples kindly provided by Prof. Dr. Dr.h.c. Ewald Werner, Institute of Materials Science, TUM.Hand scraping carbon steel: carbide insert geometryAn Engineers Findings2018-08-10 | An explanation of the technique I came up with to hand scrape carbon steel. With particular emphasis on scraper blade geometry.Borderline Machining on the Mikron WF-1: Pumping IronAn Engineers Findings2018-07-31 | Machining the side walls of my newly designed 1200mm/36ton-press brake prototype. These side walls should be considered way too large and too heavy for my Mikron WF-1 milling machine. But with some engineering I could manage to get the job done.Mikron WF-1 Milling Machine Reconditioning: Scraping, Modifications and RepairsAn Engineers Findings2018-04-21 | An audio-commented slideshow comprised of over 200 pictures taken during reconditioning of my 50 years old Mikron WF-1 toolroom milling machine.