Hydraulic Jump with Ray Tracing | FLOW-3D HYDROFLOW-3D2026-11-22 | Hydraulic Jump with Ray Tracing | FLOW-3D HYDROPowder Directed Energy Deposition Additive Manufacturing - Bead Geometry Modelling | FLOW-3D AMFLOW-3D2024-05-17 | In this simulation, we use Computational Fluid Dynamics (CFD) model of FLOW-3D AM to predict the morphology of bead in DED Additive Manufacturing. The simulation captures the dilution of newly deposited material into the previous layer or substrate. Moreover, the temperature, solid fraction, and velocity inside the melt pool are calculated which gives a detailed picture of the bead formation in this metal 3D printing process. For more information on FLOW-3D AM, visit flow3d.com/products/flow3d-am/.Multipass Simulation of SS316L Powder-fed Directed Energy Deposition (DED) | FLOW-3D AMFLOW-3D2024-05-15 | This powder-fed directed energy deposition (DED) simulation animation shows 3 layers, or passes, of material deposition along a straight strack. The SS316L powder is fed by 2 sources along the perpendicular axis to the laser motion. Learn more about FLOW-3D AM by visiting flow3d.com/products/flow3d-am/.Multipass Simulation of Two Material Powder-fed Directed Energy Deposition (DED) | FLOW-3D AMFLOW-3D2024-05-10 | This powder-fed directed energy deposition (DED) simulation animation shows 3 layers, or passes, of material deposition along an L-shaped track. The powder feed contains 2 materials, each with separate material properties that affect the thermals and bead dimensionality of the tracks. This animation visualizes the four powder sources and laser beam. Learn more about FLOW-3D AM by visiting flow3d.com/products/flow3d-am/.
Top: Temperature field in degree C Bottom: Concentration map of the two different materialsMelt Pool Simulation of Overhang Dross in Laser Powder Bed Fusion (LPBF) | FLOW-3D AMFLOW-3D2024-05-08 | This laser powder bed fusion (LPBF) simulation animation shows 3 melt tracks as the laser beam approaches a down-facing overhang surface that runs parallel to the laser motion. The lack of structural support beneath the overhang surface causes the melt pool to sink lower than its neighboring layers, producing an effect called "Dross". Naturally, dross formation causes dimensional inaccuracy, high surface roughness and also adversely affects the mechanical properties of printed components. FLOW-3D AM is used to quantify process parameters to reduce defects like dross. Learn more about FLOW-3D AM by visiting flow3d.com/products/flow3d-am/.
Top left: Temperature field in degree C Top right: Solid fraction Bottom left: Top view using ray-tracing to visualize metallic material Bottom right: Front view using ray-tracing to visualize metallic materialMelt Pool and Laser Beam Visualization of Laser Powder Bed Fusion (LPBF) Simulation | FLOW-3D AMFLOW-3D2024-05-03 | This laser powder bed fusion (LPBF) simulation animation showcases the unique post processing capabilities available with FLOW-3D POST. The melt region and heat-affected zone are isolated from the surrounding powder bed as the ring-shaped laser beam is visualized scanning along the track length. Learn more about FLOW-3D AM by visiting flow3d.com/products/flow3d-am/.Junction Manhole Losses | FLOW-3D HYDROFLOW-3D2024-05-01 | Understanding the hydraulic losses at junction manholes can be very important when designing sewer infrastructure and assessing hydraulic grade lines in the system. Three-dimensional computational fluid dynamics modeling can help you estimate these losses and evaluate design alternatives. This FLOW-3D HYDRO example compares three design options for a junction manhole: 1) base model with no benching, 2) benching halfway up the pipe diameter, and 3) benching that goes above the pipe crown. For this particular flow rate and downstream water level, the half-pipe benching results in a head loss reduction of 28% while the taller benching case reduces the head loss by 33% when compared to the base case without benching. Learn more about FLOW-3D HYDRO by visiting flow3d.com/products/flow-3d-hydroKO2 Spillway PMF Flood Cross Section | FLOW-3D HYDROFLOW-3D2024-04-26 | This FLOW-3D HYDRO simulation shows a cross section of the flow down a tailings storage facility (TSF) spillway during a probable maximum flood (PMF), as modeled by MECATER Ingénierie of Tunisia. "We found that CFD modeling was a powerful tool for evaluating the design of our spillway structure. In fact, with its capability to simulate hydraulic jump and real conditions such as air entertainment model, fluid characteristics and also its accurate FAVOR™ method to generate meshing, we were able to confirm the results we’d obtained earlier with 2D software tools as well as those of our scale model." Read the full MECATER Ingénierie FLOW-3D HYDRO case study at flow3d.com/spillway-success/.Liquid Metal Deposition | FLOW-3D WELDFLOW-3D2024-04-24 | In this simulation, we study the deposition of liquid metal droplets on a moving substrate with FLOW-3D. Thanks to the two-fluid solution, we can analyze the velocity and temperature in the gas surrounding the metal droplet. The simulation predicts the morphology of the deposited track. For simplicity, the nozzle was not included in the simulation and the liquid metal enters the domain using the droplet source. For more information on FLOW-3D WELD, visit flow3d.com/products/flow3d-weld/.Fusion Zone During Hairpin Laser Welding | FLOW-3D WELDFLOW-3D2024-04-19 | The weld dimensions are monitored during hairpin welding to ensure defect free and optimal process. Creating a digital twin of the process in FLOW-3D WELD adds another layer to the hairpin welding control and enables prediction of the influence of laser parameters on the melt pool behavior and final shape of the weld. For more information on FLOW-3D WELD, visit flow3d.com/products/flow3d-weld/.Hairpin Laser Welding Simulation | FLOW-3D WELDFLOW-3D2024-04-17 | In this simulation, we can observe the evolution of the fusion zone during hairpin welding. The shape and dimensions of the weld are important for the efficiency and robustness of electric motors. The simulation in FLOW-3D WELD is validated with experimental photographs from D'Arcangelo et al., Comprehensive benchmarking of laser welding technologies including novel beam shapes and wavelengths for e-drive copper hairpins, Optics & Laser Technology, Volume 169, 2024. For more information about FLOW-3D WELD, visit flow3d.com/products/flow3d-weld/.Hairpin Laser Welding | FLOW-3D WELDFLOW-3D2024-04-12 | This animation shows melting of copper during the hairpin welding in an electric motor. A ray tracing algorithm of FLOW-3D POST was used to create a realistic visualization of the material free surface. The simulation in FLOW-3D WELD predicts the shape and dimensions of the fusion zone as well as the temperatures and velocities inside the melt pool. The robustness of the hairpin welding process is critical to the development of the e-mobility sector. For more information on FLOW-3D WELD, visit flow3d.com/products/flow3d-weld/.Tailings and Non-Newtonian Fluids | FLOW-3D HYDROFLOW-3D2024-04-10 | FLOW-3D has long had the ability to model non-Newtonian fluids, but FLOW-3D HYDRO added the ability to model these fluids in a more robust tailings physics model. This video is a simple example of a non-Newtonian fluid dam break. The first part of the video is a two-dimensional "slice" model and the second part is a full three-dimensional model. This example uses a homogeneous non-Newtonian fluid, but the tailings model allows you to specify multiple tailing layers, including a Newtonian layer (i.e., water), and see how the various layers intermix during a dam break model. Another advantage of the FLOW-3D HYDRO tailings model is that you can combine both two-dimensional depth-averaged meshes with fully three-dimensional meshes in the same model to help you model larger dam break extents. Learn more about FLOW-3D HYDRO by visiting us at flow3d.com/products/flow-3d-hydro/.Wave Overtopping Comparison | FLOW-3D HYDROFLOW-3D2024-04-05 | This FLOW-3D HYDRO model illustrates the benefits of natural vegetation, such as mangroves, as a coastal defense mechanism. In the top model, the incoming waves run up on an unprotected beach slope and the total volume of fluid that overtops the beach is quantified. In the other run, a 3D object representing mangroves is added at the base of the beach slope. The mangroves help to dissipate the wave's energy and reduce the overtopping volume. Learn more about FLOW-3D HYDRO at flow3d.com/products/flow-3d-hydro/.Flip Bucket Spillway | FLOW-3D HYDROFLOW-3D2024-04-03 | FLOW-3D HYDRO comes with dozens of built-in model examples, such as this flip bucket spillway model. These examples are great learning tools for both new and experienced users. With these examples, you can load in the example input file, see what settings were used, and run it right out of the box. You can also play around with different mesh sizes, numerical options, geometry edits, and boundary conditions as ways of learning how to navigate FLOW-3D HYDRO and its options available to you. Learn more about FLOW-3D HYDRO by visiting us at flow3d.com/products/flow-3d-hydro/.Bridge Overtopping | FLOW-3D HYDROFLOW-3D2024-03-29 | Bridges and culverts can undergo complex hydraulics when the water level overtops the roadway. In this FLOW-3D HYDRO example, the water level rises above the roadway and the bridge experiences pressure flow through the opening and weir flow over the bridge deck. A three-dimensional computational fluid dynamics model can help you quantify the complex hydraulic losses associated with bridges and culverts in overtopping situations. Learn more about FLOW-3D HYDRO by visiting flow3d.com/products/flow-3d-hydro/.Fish Ladder | FLOW-3D HYDROFLOW-3D2024-03-27 | FLOW-3D HYDRO's geometry handling makes it easy to test different geometries and design iterations. Once the base model is set up, you only need to swap out your three-dimensional objects with the new designs to assess their impacts. In the case of this fishway model, you could easily model different boundary conditions or designs to try and improve the hydraulics seen in these results. For example, the hydraulic jump in the top corner is close to overtopping the wall and the velocity throughout the fishway may be too high for the fish you are trying to pass through the structure. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroHydraulic Jump in a Sink | FLOW-3D HYDROFLOW-3D2024-03-22 | This video demonstrates the formation of a hydraulic jump in a sink using FLOW-3D HYDRO. Initially, high-velocity water flows rapidly and smoothly from a faucet into the sink. However, as it loses energy, it gradually slows down and accumulates around the inflow point. FLOW-3D HYDRO accurately predicts the location and behavior of this jump. Post-processing is performed using FLOW-3D POST, an advanced tool that offers sophisticated visualization and analysis capabilities for all FLOW-3D products. This tool enables engineers to optimize their CFD results for analysis and presentation purposes through a user-friendly interface. Learn more about FLOW-3D HYDRO by visiting flow3d.com/products/flow-3d-hydroFloating Flood Barrier | FLOW-3D HYDROFLOW-3D2024-03-20 | This model of a floating flood barrier showcases FLOW-3D HYDRO's moving object physics. In this model, the floating barrier motion is coupled with the fluid flow. When the water level rises within the structure, the barrier floats upward to prevent the floodwater from passing beyond the barrier. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroFrac Tank Hydraulics | FLOW-3D HYDROFLOW-3D2024-03-15 | Hydraulic mixing is critical when utilizing frac tanks in oil and gas industry as a mobile water storage solution. A improved hydraulic mixing can lead to a more efficient treatment system. To model the hydraulic characteristics, we set up the simulation with scalar model to visualize the mixing. Together with streamline plots and other advanced post-processing tools, it is made easy to analyze an open top tank with such configuration. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroHybrid 2D/3D Bridge Hydraulics | FLOW-3D HYDROFLOW-3D2024-03-13 | In FLOW-3D HYDRO, you can use either two-dimensional (2D) depth-averaged or three-dimensional computational meshes. You can even use both 2D and 3D meshes within the same model. In this bridge example, a 2D mesh is used in the larger extent of the river, but a detailed 3D mesh is used near the bridge to capture the 3D flow behavior at the bridge piers. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroHigh Viscosity Fluid | FLOW-3DFLOW-3D2024-03-08 | Free surface flows are common in the design and manufacture of consumer products used in both, the home and office environment. Designing such a process to minimize waste while maximizing production speed can lead to significant cost savings over time. This simulation shows the filling of a Hair Relaxer in a jar. The hair relaxer has a very high viscosity of 100000 cP. The jar rotates at a constant speed of 30 RPM while the nozzles feed the hair relaxer at a rate of 8.33 cu-cm/s. FLOW-3D can be used to accurately simulate and optimize such consumer product designs with the help of its advanced multiphysics models including air entrainment, porous media, and surface tension. For more information on using FLOW-3D, visit flow3d.com/products/flow-3dSpillway Gate Opening | FLOW-3D HYDROFLOW-3D2024-03-06 | The spillway gates in this FLOW-3D HYDRO model are undergoing a prescribed rotation about a fixed axis. Using FLOW-3D's moving object physics allows you to investigate different gate opening speeds and gate opening sequences with just a few clicks of your mouse once the base model is established. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroSpillway Debris Screen | FLOW-3D HYDROFLOW-3D2024-03-01 | This spillway model highlights FLOW-3D HYDRO's moving object capabilities. The logs are free to move and collide with each other and the debris screen at the spillway crest. Each object’s motion and fluid flow are coupled dynamically and affect each other. You can model hundreds of independent moving objects within a single FLOW-3D HYDRO model (up to 500 objects at the time of this caption). For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroGate Velocity | FLOW-3D CASTFLOW-3D2024-02-23 | FLOW-3D CAST provides users with many ways to instrument their casting simulations to provide a deep understanding of the behavior of their designs. This video shows the use of history probes placed in the gates to gain insight into the flow balance between gates. This information is very helpful, especially in multi-cavity castings where the flow between casting cavities varies. For more information on FLOW-3D CAST, visit flow3d.com/products/flow-3d-castStatic Mixers | FLOW-3D HYDROFLOW-3D2024-02-22 | Static mixers are often used in pipelines to mix fluids without using any moving components or external power. In this FLOW-3D HYDRO video, three different styles of static mixers are modeled for the same hydraulic conditions in a large diameter pipe. Each model introduces a scalar dye through a small pipe just downstream of the mixer and the goal is to have this injected fluid become well-mixed in the pipeline. You can use the outputs from the FLOW-3D HYDRO model to assess how well the static mixer meets the mixing criteria of the particular application. For more information on FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydro/.Cavitation Potential in HPDC | FLOW-3D CASTFLOW-3D2024-02-21 | Because of the high velocities and accompanying low pressures created in HPDC processes, cavitation is possible. Cavitation bubbles collapsing on the die surface can create pitting, which in turn causes surface quality issues on the casting as well as drastically shortening the life of expensive dies. FLOW-3D CAST’s cavitation potential model is a powerful tool for identifying areas on the die where cavitation is likely to occur. For more information about FLOW-3D CAST, visit flow3d.com/products/flow-3d-cast/.Directed Energy Deposition Spiral Bead Simulation | FLOW-3D AMFLOW-3D2024-02-16 | FLOW-3D AM simulation of laser wire-based directed energy deposition with IN718. Understand the complex interplay of heat transfer, surface tension, viscosity, and phase change for consistent bead deposition. Learn more about using FLOW-3D AM at flow3d.com/products/flow3d-amNappe Aeration for a Rectangular Weir | FLOW-3D HYDROFLOW-3D2024-02-14 | When a nappe stretches along the entire length of a rectangular weir, the air under the nappe can become entrained in the flow. When there is an insufficient source of air to replenish under the nappe, the nappe can attach to the downstream face of the weir. In this FLOW-3D HYDRO example, an unaerated nappe condition switches to an aerated condition when the ventilation tube is added to the nappe. Learn more about using FLOW-3D HYDRO at flow3d.com/products/flow-3d-hydroWire Arc Additive Manufacturing Simulation | FLOW-3D AMFLOW-3D2024-02-09 | This FLOW-3D AM simulation of a wire arc additive manufacturing process with SS304 helps us understand the complex interplay of heat transfer, surface tension, viscosity, and phase change for achieving consistent bead deposition. Learn more about using FLOW-3D AM for wire arc and other additive manufacturing processes at flow3d.com/products/flow3d-am/.Flap Gate Discharge Validation | FLOW-3D HYDROFLOW-3D2024-02-07 | FLOW-3D HYDRO makes it easy to model moving objects that are coupled with the fluid flow. In this example, the hinged flap gate opens based on the hydraulic forces acting on it. At the end of the video, there are plots comparing the modeled results to experimental results for the pressure head and discharge flow rate in both dry and submerged discharge conditions. Learn more about using FLOW-3D HYDRO at flow3d.com/products/flow-3d-hydroWire-based Directed Energy Deposition Simulation | FLOW-3D AMFLOW-3D2024-02-02 | FLOW-3D AM simulation of laser wire-based directed energy deposition with SS304. Understand the complex interplay of heat transfer, surface tension, viscosity, and phase change for consistent bead deposition. Learn more about using FLOW-3D AM at flow3d.com/products/flow3d-am/.Scour Protection at Culvert Outlets | FLOW-3D HYDROFLOW-3D2024-01-31 | Using FLOW-3D HYDRO's sediment transport physics, this example models the impact of scour protection placed at a series of culvert outlets. The sediment transport physics simulate an erodible bed and you can observe a scour hole developing at the downstream edge of the scour protection as the model progresses. Learn more about using FLOW-3D HYDRO at flow3d.com/products/flow-3d-hydroPowder Settling Simulation | FLOW-3D AMFLOW-3D2024-01-26 | This powder settling simulation in FLOW-3D AM provides insight into the effects of powder size distribution and material properties on powder packing. The results of a powder settling simulation such as this one would then be used in subsequent powder spreading simulations. Learn more about using FLOW-3D AM at flow3d.com/products/flow3d-am/.Air Entrainment at a Labyrinth Spillway | FLOW-3D HYDROFLOW-3D2024-01-24 | This example of a labyrinth weir spillway illustrates FLOW-3D HYDRO's air entrainment physics in a one-fluid volume of fluid model. The air entrainment physics estimate the rate at which gas (represented by void regions) is entrained into the flow using a balance of stabilizing forces (gravity and surface tension) and destabilizing forces (turbulence). Although the primary focus of the model is to compute the air entrainment resulting from turbulent disturbances at a free surface, the model also contains logic for handling entrainment resulting from laminar jets impinging on a free surface. In this video, the fluid is colored by the entrained air volume fraction calculated by the air entrainment physics. Learn more about using FLOW-3D HYDRO at flow3d.com/products/flow-3d-hydroPowder Spreading Simulation | FLOW-3D AMFLOW-3D2024-01-19 | Powder spreading simulation in FLOW-3D AM for understanding the effects of PSD, material properties, and recoater operating conditions on powder packing. To be used in subsequent melting simulations. Learn more about using FLOW-3D AM at flow3d.com/products/flow3d-am/.Fusegate Tipping | FLOW-3D HYDROFLOW-3D2024-01-17 | Fusegates have been added to reservoirs as a way to increase water storage capacity of the reservoir. Under normal operation, flood conditions will flow over the fusegate crest similar to a typical weir. For larger flood events, water can flow into the fusegate inlet well and lead to an uplift pressure that causes the fusegate to tip. This FLOW-3D HYDRO example models the tipping condition of a fusegate under an extreme flood condition. The general moving object physics have been used to simulate the motion of the fusegate. For more information on FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroFLOW-3D AM Binder Jetting Droplet Simulation | FLOW-3D AMFLOW-3D2024-01-12 | This FLOW-3D AM simulation of binder jetting shows a droplet impacting a powder bed. Analysis provides information on capillary effects and pressure forces due to droplet momentum and material properties. Learn more about using FLOW-3D AM for binder jetting and other additive manufacturing processes at flow3d.com/products/flow3d-am/.High Pressure Die Casting (Hot Chamber) CFD Simulation | FLOW-3D CASTFLOW-3D2024-01-10 | Solidification process of hot chamber HPDC is simulated FLOW-3D CAST. Filling behavior and small droplets (splashes) must be considered to represent this process. A special particle model is used to reduce the computation time. If a droplet occupies a very small portion of the mesh cell, it is converted to a particle. Tracking of its movement is much less computationally expensive in this case.
Velocity during the filling process in analyzed in order to confirm proper gate design. It proves that the critical velocities of 50 mm/s are not achieved during the process. Recent additions of even more physical detailed air entrainment model allow entrained air, which is assumed to be in the form of bubbles, to be modelled as rising in the surrounding liquid metal because of buoyancy forces and even leaving the liquid if it reaches a free surface. Find more about using FLOW-3D CAST by visiting us at flow3d.com/products/flow-3d-castProduction of Aluminum Ingots with a Rotating Casting Wheel | FLOW-3D CASTFLOW-3D2024-01-05 | Aluminum ingots are usually produced using a rotating casting wheel. In this casting process, it is important to strive for low turbulence filling to minimize air and oxide inclusions. Thanks to FLOW-3D CAST's ability to define any geometry as a moving geometry, the rotation of the casting wheel and the translation of the molds can be modeled very easily. In combination with the realistic flow simulation, FLOW-3D CAST is able to accurately represent the flows and turbulence as well as possible oxide or air inclusions in the melt. The entire heat balance, solidification and cooling of the ingots in combination with a stress calculation can also be examined in detail in order to avoid undesirable porosities, deformations or cracks.
For more information on using FLOW-3D CAST, visit us at flow3d.com/products/flow-3d-castKO2 Spillway PMF Flood 3D | FLOW-3D HYDROFLOW-3D2024-01-03 | From a project by MECATER Ingénierie of Tunisia, this simulation shows the fully 3D flow down a spillway during a probable maximum flood (PMF). MECATER delivered a strong solution to their clients, Prony Resources of New Caledonia. “Using simulation software easily saved us a month or more of effort while helping us to deliver an optimized design that met our client’s criteria. We recently visited the New Caledonia facility and we were very proud to see the completed spillway. Based on these results, we now see FLOW-3D HYDRO as an invaluable tool in any large-scale hydro engineering project.” Read the full MECATER Ingénierie FLOW-3D HYDRO case study at flow3d.com/spillway-success/.High Pressure Die Casting CFD Simulation of Dental Lamp Housing | FLOW-3D CASTFLOW-3D2023-12-29 | Solidification process of HPDC a lamp housing used for in dental industry is simulated FLOW-3D CAST. Solidification related defects are analyzed. The size of pores is presented with the color scale. Volume of fluid (TruVOF) method is used to achieve realistic filling results. VOF is a simple and economical way to track free surfaces. FLOW-3D CAST is flexible and efficient in solving problems involving highly complex free surface configurations, such as the behaviour of cast metal during the process of filling under high pressure.
FLOW-3D CAST full chemistry solidification model is used. The model advances the industry into the next frontier of casting simulation – giving users the ability to predict the strength and integrity of cast parts while reducing scrap and still meeting product safety and performance requirements. Find more about using FLOW-3D CAST, visit us at flow3d.com/products/flow-3d-castDebris Blockages in Culverts | FLOW-3D HYDROFLOW-3D2023-12-27 | During significant flood events, debris can be transported down the waterway and become lodged at bridges and culverts. Accumulated debris can reduce the flow capacity of the bridge or culvert, this resulting in more flooding upstream. In this FLOW-3D HYDRO example, three tire-shaped objects and one tree trunk are released upstream of the culvert to see if they become lodged upstream of the culvert or are able to pass through. In FLOW-3D HYDRO, debris blockages can be modeled with dynamically moving objects or with stationary solid or porous objects placed in the model domain. Learn more about FLOW-3D HYDRO at flow3d.com/products/flow-3d-hydro/.Investment Casting CFD Simulation | FLOW-3D CASTFLOW-3D2023-12-22 | Investment casting with a ceramic shell mold is simulated in FLOW-3D CAST. In addition to conduction and convection heat transfer models a Radiation model is used, since it has a big influence on the final results in this process. The general equation for radiation heat flux can be formulated for parallel radiating surfaces using grey-body emissivity. Special method is implemented to model the ceramic shell. The shell is considered to be preheated before the process of filling. Accurate filling to find casting filling related defects like entrained air, free surface defects. Chemistry-based carbon and low alloy steel solidification model used to analyze microstructure evolution during the solidification. Find more about using FLOW-3D CAST by visiting us at flow3d.com/products/flow-3d-castCommunicate Your Results | FLOW-3D HYDROFLOW-3D2023-12-18 | This webinar is the last of a four-part series to learn the basics of the FLOW-3D HYDRO workflow. In this brief first 15-minute webinar, we illustrate the common post-processing functions available in FLOW-3D POST that you can use to analyze the model output and create visual outputs for your presentations and reports. Learn more about FLOW-3D HYDRO by visiting us at flow3d.com/products/flow-3d-hydroAdd Sediment Transport | FLOW-3D HYDROFLOW-3D2023-12-18 | This webinar is the third in a four-part series to learn the basics of the FLOW-3D HYDRO workflow. In this brief 15-minute webinar, we will use the weir model from the first two webinars and add sediment transport physics. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroIncorporate Moving Objects | FLOW-3D HYDROFLOW-3D2023-12-18 | This webinar is the second in a four-part series to learn the basics of the FLOW-3D HYDRO workflow. In this brief 15-minute webinar, we will build upon the weir example from the first webinar and add further complexity by activating the moving object physics. For more information on using FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroBasic Model Setup | FLOW-3D HYDROFLOW-3D2023-12-18 | This webinar is the first in a four-part series to learn the basics of the FLOW-3D HYDRO workflow. In this brief 15-minute webinar, we will illustrate the basic FLOW-3D HYDRO modelling workflow by creating a model of flow going over a weir. For more information on how to use FLOW-3D HYDRO, visit flow3d.com/products/flow-3d-hydroGeneral Multiphysics Applications Webinar | FLOW-3DFLOW-3D2023-12-18 | In this webinar, we go over examples, discuss the physics involved and focus on the nuances of simulating such complex engineering applications. In addition to the advanced free surface modeling capabilities in FLOW-3D, we will show how physics such as heat transfer, porous media, phase change, dispersed media, etc. can be captured. Learn more at flow3d.comPiston Tilt Pour Casting CFD Simulation | FLOW-3D CASTFLOW-3D2023-12-15 | This is a three-part simulation setup in FLOW-3D CAST for a tilt pour aluminum casting of a piston. This simulation uses insulated risers and cooling channels. The first simulation is a thermal die cycling to find the steady state level of heat saturation in the mold. Once the thermal data is accessed, a filling simulation is done to access filling behavior and defects. Lastly, a solidification simulation is run to assess shrinkage porosity and microstructure. NIRF model is implemented for fast and easy setup of the tilt pour process. Surface tension is modelled to be temperature dependent. Rotation of the furnace is described as moving object. Full chemistry solidification model provides accurate results of microstructure and mechanical properties. Find more about using FLOW-3D CAST at flow3d.com/products/flow-3d-castGravity Die Casting CFD Simulation | FLOW-3D CASTFLOW-3D2023-12-13 | Gravity die casting of two components is simulated in FLOW-3D CAST. Volume of fluid (TruVOF) method is used to achieve realistic filling results. VOF is a simple and accurate way to track free surfaces. Simulation was done in three steps. Firstly, thermal die cycling was implemented to determine local temperature distribution of the mold. Based on this results metal filling is simulated. Lastly, solidification simulation is carried out to analyze solidification related defects. In simulation material properties, such as surface tension, density and viscosity are temperature dependent. This has a big influence on accuracy of the final results. In addition, presolidification during the process of filling is considered.