Tomorrow's Sunset | IDM track with Cirklon, Prophet 10, System-8, Minimoog, Machinedrum, and JD-990 @MIDERA

Uploaded December 2025 | Updated September 2026, 2 weeks ago

Two years ago today, I lost my mom... Often I write tracks as tributes, remembering the end - which was really a horrible experience.

But I know what matters isn't what happened at the end, but really I should take the time to celebrate what she gave me: my life, my family, my experiences, my abilities. Her and my dad are the reason I have any of this and can write anything at all. So, I'll just say that I'm thankful to both of them. That's what this day can become, a reminder of what I've been given.

Track:
Sequentix Cirklon 2 sequenced everything.
Sequential Prophet 10 for initial sound
Moog Minimoog for bass
Roland System-8 for pads
Roland JD-990 for plucked sounds
Elektron Machinedrum for drums

#prophet10 #minimoog #machinedrum

Tomorrows Sunset | IDM track with Cirklon, Prophet 10, System-8, Minimoog, Machinedrum, and JD-990

Wayward shift | Moog Minimoog, Spectralis 2, Prophet 10, Prophet 12, Nord Drum 2

Ensoniq ESQ-1 first impression and walkthrough

Making some patches with the Access Virus TI

The lies ahead | Moog Minimoog, Spectralis 2, Prophet 12, Prophet 10, Nord Drum 2 electronic

$Ever present | A Kawai SX-240 and Rhodes Piano Improvisation Recently Ive got a few rude comments on my page, misconstruing events Id spoken about in the past... not just trolls (although, yes, they are those, but they dont bother me as much as people making up and changing what Id said). Now Im starting to think that sharing my life is a bad idea. Anyway - about this track, Id actually written it and had enjoyed everything Id done, except, when I went to look at the recording, it had stopped after 10 minutes! My computer went to sleep!!! Whoops. I had to make a new track, and here it is. Fractal Audio FM3 for reverb and delay #sx240 #fractalaudiofm3 #rhodespiano$ $Roland Juno 60 | Ambient soundscape with Fractal Audio FM3 I decided to help a friend and replaced all of his Roland Juno 60 sliders. I figured I’d done a lot of similar work for myself, and I’ve had a lot of people help me out so I wanted to pass it forward. Well, after spending 3 hours replacing the sliders, it was 12:30AM and I turned on the unit to test it out. But it went horribly wrong. Nothing sounded right. Noise was always present, the Attack slider didn’t work, Sub was always on, you get the picture. By this point, I was totally stressed out. I had destroyed a $3000 synth! I tried going to sleep, but it was around 3AM before I could. I woke up the next day, stressed. I ran downstairs to see if it was just something simple I missed, but nothing seemed wrong. All the pins had continuity to the traces they were going towards. By 5PM that day, I finally wrote on a facebook group. Someone mentioned something regarding the new sliders from Syntaur. He said they’re chassis legs are too short. Specifically, the Attack slider chassis provides ground to IC5, pin 8. But when I checked, there was continuity from the pad to IC5 pin 8. HOWEVER, the pad was NOT connected to the chassis. I quickly threw the old slider in, and magically… it all worked. I couldn’t believe it. That was about 24 hours of terror as I tried to figure out what went wrong. However, it is now going strong, perfectly. I’m very thankful to that facebook group! Fractal Audio FM3 used for delay/reverb/fx. #rolandjuno #Juno #fractalaudiofm3$

Radikal Technologies Accelerator soundscape - In time the webs entangle us

Roland JD-800 soundscape - A journey into the sun