For Nissan Qashqai Tailgate Boot Handle Repair Clip Kit Clips Snapped 2006 -2013 Instructions Guide X8R Ltd 2026-09-28 | For Nissan Qashqai Tailgate Boot Handle Repair Clip Kit Clips Snapped 2006 -2013 Instructions Guide
Faulty Wipers On Your Audi Q7? Repair Them, Dont Replace! Use This X8R Wiper Bush Repair Kit X8R Ltd 2023-10-02 | Link to purchase item:Symptoms of FaultJuddering or erratic wipers, wiper rods popped off at ball joints, wipers over-arching, windscreen wipers not working or only one workingThe FaultThe poor quality bearings on your vehicles wiper linkage rods wear causing these symptomsThe original soft plastic bush bearings on each end of the two wiper linkage push rods wear down leading to the push rods popping off the ball joint and causes the symptoms noted above. Other designs of bushes available are made from the same material as OEM and of the same designThe SolutionFit our improved wiper bushes and circlips to restore your wipers to full healthSave on the cost of a complete wiper mechanism or wiper rods complete with poorly designed bushes, which will no doubt fail again in future. Install X8R’s wiper bush kit to save time and money.X8R’s wiper bushes are made of reinforced Nylon, guaranteeing the life of your wiper rods for many years to come. The bushes are designed to last, with a mating edge for the circlips to attach into, making sure they do not come loose in future. Vehicles AffectedAudi Q7 4L between 2005-2015Audi Q7 & SQ7 4M between 2015-2020Audi Q7 & SQ7 4MB 2020 onwardsBentley Bentayga 2015 onwardsSuitable for left and right hand drive modelsAssociated part numbers:4L2955023F, 4L2955023D, 4L2955119A, 4L2910113, 4L1955023D4M2955023B, 4M8955023C, 4M8955119ASuitable for Bosch and Valeo wiper linkagesYou Will Receive4 x reinforced Nylon wiper bushes4 x circlips
Struggling For Storage In Your Van, Camper or Commercial Vehicle? Install This X8R Universal Shelf! X8R Ltd 2023-09-27 | Link to purchase product: The FaultLack of storage solutions available from factory options in commercial vehiclesMost commercial vehicles, van and camper conversions have limited storage solutions. They often come with the rear of the vehicle completely bare except from the MDF cladding on the inside of the shell.The SolutionInstall X8R’s universal storage shelf in under 10 minutes for a simple storage solutionX8R’s universal storage shelf is the perfect solution for tradespeople, van owners and campers. The shelf comes with colour coded self-tapping screws for an easy installation (no power tools required) in under 10 minutes. All you need is a marker, spirit level and Philips head screwdriver.The shelf can easily be stacked on the door cards, allowing you to install as many shelves as you wish. The shelf is made from vacuum formed ABS plastic, making it strong and durable for commercial use. It is the ideal size for tools, consumables, magazines and more. The shelf has the following dimensions:48cm wide x 13cm high x 10cm deep.Vehicles AffectedThis is a universal product. Please check the dimensions above to see if it will be suitable for where you want to install it.You Will Receive:1 x plastic storage shelf
How To Stop Your Van Being Stolen! | Pedal Guard Security for Mercedes VW Fiat Ford Citroen Peugeot X8R Ltd 2023-09-27 | Link to purchase product: x8r.co.uk/search/?cat=0&q=pedal+guardLink to downloadable instruction guide: instructables.com/Pedal-Guard-Instruction-GuideWe offer a multitude of different pedal guards, here are the part numbers and their compatibility:X8R0265:Mercedes Sprinter 2006-2018Volkswagen Crafter 2006-2017X8R0266:Fiat Ducato 2015-2022Peugeot Boxer 2015-2022Citroen Relay 2015-2022Automatic gearboxes onlyX8R0267:Fiat Ducato 2015-2022Peugeot Boxer 2015-2022Citroen Relay 2015-2022Manual gearboxes onlyX8R0268:Fiat Ducato 2007-2014Peugeot Boxer 2007-2014Citroen Relay 2007-2014Manual gearboxes onlyX8R0269:Ford Transit MK8 2014-2020Not suitable for post 2020 facelift modelsX8R0270:Ford Transit MK7 2001-2014
Fix Your Broken Nissan Qashqai Tailgate Handle With The X8R Repair Kit! No Paint, No Glue, Easy Fix! X8R Ltd 2023-09-18 | Link to purchase Nissan Qashqai tailgate repair kits: x8r.co.uk/nissan/tailgate-repair-kit.htmlLink to downloadable instruction guide: instructables.com/Nissan-Qashqai-Tailgate-Boot-Handle-Repair-Clip-KiLink to full YouTube tutorial: youtube.com/watch?v=Nlx1_yr186Q&t=150sFor any questions please do not hesitate to contact us on +441843446643 or sales@x8r.co.uk
How To Fix Your Cracked Mini Convertible Seals With The X8R Repair Kit! X8R Ltd 2023-09-18 | Link to purchase product: x8r.co.uk/mini-convertible-canvas-roof-cover-seal-trim-repair-kit-rubber-belt-line-beltline.htmlLink to downloadable instruction guide: instructables.com/Mini-R52-Belt-Line-Weather-SealLink to full YouTube tutorial: youtu.be/SRs9oAwSe0EFor any questions, please do not hesitate to contact us on +441843446643 or email us on sales@x8r.co.uk
How To Fix Death Wobble On Your Suzuki Jimny With X8R! | Kingpin Repair Kit X8R Ltd 2023-09-18 | Link to X8R Suzuki Jimny kingpin repair kits: x8r.co.uk/suzuki/kingpin-repair-kits.htmlDownloadable instruction guide: instructables.com/Jimny-Kingpin-Repair-GuideYouTube instruction guide: youtu.be/fXrmbH8ZvJsFor any other questions, please do not hesitate to contact us on +441843446643 or email sales@x8r.co.uk
How To Repair Your DISA Valve In Under 30 Minutes! | X8R Repair Kit 2.2/2.5/3.0 BMW M54 X8R Ltd 2023-09-14 | Links to purchase items:2.2/2.5L repair kit: x8r.co.uk/bmw-disa-valve-intake-adjuster-unit-rebuild-rattle-aluminium-fix-m54-2-2-2-5.html3.0 repair kit: x8r.co.uk/bmw-disa-valve-intake-adjuster-unit-rebuild-upgrade-rattle-aluminium-fix-m54-3-0.htmlFull YouTube instruction guide: youtube.com/watch?v=kIq7QJpRnRwDownloadable instruction guide: instructables.com/Bmw-DISA-Valve-Unit-Rattle-Repair-Fix-Kit-Rattling
How To Prevent A Break-In On Your Ford Transit Custom 2012 Onwards! | X8R Rear Door Lock Shield Kit X8R Ltd 2023-09-05 | Symptoms of faultLow security is a concern when storing valuable items inside your van.The problemThe OEM door locking mechanism is easily bypassed by criminals.It is very common for criminials to attempt break-ins on these vans by drilling a hole through the side door to access the internal mechanisms of the lock and open the door, this being able to take whatever is stored in the back of the van. If your van has been broken into you would be required to replace the whole door, which can often prove expensive and time consuming, especially if you need to respray the new door.A common deterrent against criminals would be an alarm system, however the alarm will only be triggered once the criminals are already inside of the van. Having a visible guard on show will send a message to any prospecting criminals.Our solutionThis X8R kit contains everything you need to repair a past break-in, as well as protect it from future attacks.Rather than replace your door or install an expensive alarm system, install the X8R Door Lock Shield Kit. This comprehensive kit will deter theives from breaking into your vehicle by adding two extra layers of protection to your door.Our external and internal shields are made from 2.5mm stainless steel, which is over twice the thickness of the skin of the OEM doors. The shields also come with a closed cell foam gasket which sits flush between the door & the exterior shield, creating a water-tight protective barrier to prevent rust and corrosion.Vehicles affectedFord Custom 2012 onwardsYou will receive1 x Rear door brushed stainless steel exterior shield1 x X8R green powder coated stainless steel interior shield1 x Paper template1 x Closed cell foam gasket10 x Nyloc nuts10 x Washers
How To Prevent a Break-In on Your Vivaro, Trafic, NV300! 2014- X8R Side Door Lock Shield Kit X8R Ltd 2023-09-05 | Symptoms of faultIf you have already had a break-in attempt made on your van then it is likely you will have a hole drilled in the door of your vehicle, this is done to allow criminals to reach inside and simply unlock your van from the internal mechanism.The problemThe OEM door locking mechanism is easily bypassed by criminals.It is very common for criminals to attempt break-ins on these vans by drilling a hole through the side door to access the internal mechanisms of the lock and open the door, thus being able to take whatever is stored in the back of the van. If your van has been broken into you would be required to replace the whole door, which can often prove expensive and time consuming, especially if you need to respray the new door.A common deterrent against criminals would be an alarm system, however the alarm will only be triggered once the criminals are already inside of the van. Having a visible guard on show will send a message to any prospecting criminals.Our solutionThis X8R kit contains everything you need to repair a past break-in, as well as protect it from future attacks.Rather than replace your door or install an expensive alarm system, install the X8R Door Lock Shield Kit. This comprehensive kit will deter thieves from breaking into your vehicle by adding two extra layers of protection to your door. Our kit is also suitable if your van has been previously drilled in to. Our external and internal shields are both made from 2.5mm stainless steel. Adding 5mm stainless steel protection, the skin of most OEM doors is little over 1mm thick! Our shields come with a closed cell foam gasket which sits flush between the door & the exterior shield, creating a water-tight protective barrier to prevent rust and corrosion. Template included to allow accurate drilling and easier install. Please also check out our comprehensive instruction document and install video. High quality brushed stainless steel finish. Vehicles affectedVauxhall Vivaro 2014-2018Renault Trafic 2014-2018Nissan NV300 2014-2021Please note that this kit is only applicable for the left hand door (near side)You will receive1 x Left hand door brushed stainless steel exterior protective shield1 x X8R green powder coated stainless steel interior protective shield1 x Closed cell foam gasket1 x Paper template13 x Stainless steel Nyloc nuts13 x Stainless steel washers
X8R Van Door Shields for Vivaro, Trafic, NV300, Transit, Custom X8R Ltd 2023-08-30 | A 3D video to demonstrate X8R's new range of van door security shields. Compatibility as follows:X8R0238 - Rear door shield for Vauxhall Vivaro, Renault Trafic and Nissan NV300 https://x8r.co.uk/vauxhall-vivaro-van...X8R0257 - Side door shield for Vauxhall Vivaro, Renault Trafic and Nissan NV300 https://x8r.co.uk/trafic-vivaro-nv300...X8R0258 - Rear door shield for Ford Transit Customhttps://x8r.co.uk/rear-door-drill-rep...X8R0259 - Side door shield for Ford Transit Customhttps://x8r.co.uk/ford-custom-side-do...X8R0260 - Side door shield for Ford Transit MK8 https://x8r.co.uk/ford-transit-side-d...
How To Prevent A Break-In On Your Ford Transit Custom 2012 Onwards! | X8R Side Door Lock Shield Kit X8R Ltd 2023-08-22 | Symptoms of faultIf you have already had a break-in attempt made on your van then it is likely you will have a hole drilled in the door of your vehicle, this is done to allow criminals to reach inside and simply unlock your van from the internal mechanism.The problemThe OEM door locking mechanism is easily bypassed by criminals.It is very common for criminals to attempt break-ins on these vans by drilling a hole through the side door to access the internal mechanisms of the lock and open the door, thus being able to take whatever is stored in the back of the van. If your van has been broken into you would be required to replace the whole door, which can often prove expensive and time consuming, especially if you need to respray the new door.A common deterrent against criminals would be an alarm system, however the alarm will only be triggered once the criminals are already inside of the van. Having a visible guard on show will send a message to any prospecting criminals.criminals.Our solutionThis X8R kit contains everything you need to repair a past break-in, as well as protect it from future attacks.Rather than replace your door or install an expensive alarm system, install the X8R Door Lock Shield Kit. This comprehensive kit will deter thieves from breaking into your vehicle by adding two extra layers of protection to your door. Our kit is also suitable if your van has been previously drilled in to. Our external and internal shields are both made from 2.5mm stainless steel. Adding 5mm stainless steel protection, the skin of most OEM doors is little over 1mm thick! Our shields come with a closed cell foam gasket which sits flush between the door & the exterior shield, creating a water-tight protective barrier to prevent rust and corrosion. Template included to allow accurate drilling and easier install. Please also check out our comprehensive instruction document and install video. High quality brushed stainless steel finish. Vehicles affectedFord Transit Custom 2012 OnwardsPlease note that this kit is only applicable for the left hand door (near side)You will receive1 x Left hand door brushed stainless steel exterior protective shield1 x X8R green powder coated stainless steel interior protective shield1 x Closed cell foam gasket1 x Paper template9 x Stainless steel nyloc Nuts9 x Stainless steel washers
How To Prevent A Break-In On Your Ford Transit MK8 2014 Onwards! | X8R Side Door Lock Shield Kit X8R Ltd 2023-08-15 | Symptoms of faultIf you have already had a break-in attempt made on your van then it is likely you will have a hole drilled in the door of your vehicle, this is done to allow criminals to reach inside and simply unlock your van from the internal mechanism.The problemThe OEM door locking mechanism is easily bypassed by criminals.It is very common for criminals to attempt break-ins on these vans by drilling a hole through the side door to access the internal mechanisms of the lock and open the door, thus being able to take whatever is stored in the back of the van. If your van has been broken into you would be required to replace the whole door, which can often prove expensive and time consuming, especially if you need to respray the new door.A common deterrent against criminals would be an alarm system, however the alarm will only be triggered once the criminals are already inside of the van. Having a visible guard on show will send a message to any prospecting criminals.Our solutionThis X8R kit contains everything you need to repair a past break-in, as well as protect it from future attacks.Rather than replace your door or install an expensive alarm system, install the X8R Door Lock Shield Kit. This comprehensive kit will deter thieves from breaking into your vehicle by adding two extra layers of protection to your door. Our kit is also suitable if your van has been previously drilled in to. Our external and internal shields are both made from 2.5mm stainless steel. Adding 5mm stainless steel protection, the skin of most OEM doors is little over 1mm thick! Our shields come with a closed cell foam gasket which sits flush between the door & the exterior shield, creating a water-tight protective barrier to prevent rust and corrosion. CNC bent to accurately match the contours of the door. Template included to allow accurate drilling and easier install. Please also check out our comprehensive instruction document and install video. High quality brushed stainless steel finish. Vehicles affectedFord Transit MK8 2014 onwardsOur kit will fit all wheelbase and roof heights of the Ford Transit MK8 rangePlease note that this kit is only applicable for the left hand door (near side)You will receive1 x Left hand door brushed stainless steel exterior protective shield1 x X8R green powder coated stainless steel interior protective shield1 x Closed cell foam gasket1 x Paper template11 x Stainless Steel Nyloc nuts11 x Stainless Steel washers
TVP Trafic Vivaro Primastar EGR Delete/Blanking Kit | Stop Carbon Build-Up In Your EGR with X8R! X8R Ltd 2023-08-14 | Symptoms of FaultLoss of power, poor fuel consumption, turbo lag, rough idle, poor torque, slow engine pick-up, smokey exhaustThe FaultCarbon build up in your vehicles EGR system is restricting air flowCarbon rich recirculated exhaust gasses enter the intake manifold, over time carbon / coke deposits gather in the EGR valve and manifold blocking air flow. Resulting in reduced fuel economy and vehicle performance. Common symptoms of failure include; rough engine running, decreased throttle response and loss of power/torque.The SolutionFit our EGR kit and allow your engine to breathe once moreEliminate the risk of future carbon build up in the EGR system. Improved torque with smoother pick up and improved fuel consumption, reduced turbo lag and less nasty exhaust fumes.Our blanking kit is made from billet CNC machined anodised aluminium. It also comes bolts and with a replacement metal gasket.For off road / diagnostic use only.Vehicles AffectedRenault Trafic 2001-2014Vauxhall Vivaro 2001-2014Nissan Primastar 2001-2014Associated part numbers:Vauxhall/Opel: 44 09 585, 44 11 757, 44 12 632, 44 13 408, 44 15 798, 4416575, 4430902, 93 160 003, 93160754, 93161069, 93161219Renault: 93188701, 8200360200, 8200542997, 77 00 107 797, 82 00 229 190, 82 00 231 630, 82 00 282 880Nissan: M616666, MW30638635, MW30662336, MW30662345, MW30670108, MW30774534, MW30777076You Will Receive1 x anodised aluminium EGR blank3 x bolts1 x metal gasket
Secure Your Tipper Trailer Flatbed With The New X8R Cover! X8R Ltd 2023-08-14 | The FaultUnsecure items in tippers and flatbeds are likely to be spilt, lost or stolenOpen back tippers, trailers and flat beds can have items easily stolen or split/lost in transportation if not properly secured. The SolutionFit our reinforced Nylon flatbed nettingFit our X8R cargo cover to safely secure your fully loaded trailer. The netting is made from reinforced Nylon with webbed edging fortified with double stitching. These covers are particularly suitable for preventing sand, gravel and similar small particles from being blown away. The covers are made from UV-resistant, air-permeable fabric which prevents the covers from bellying out in strong wind, or when containers are being moved.It also comes with ultra-strong bungee cords to firmly attach it to your vehicle, looped through brass eyelets which won’t rust. Our cargo cover comes in a handy carry bag for easy and compact storage.The measurements are 11ftx8ft complete with 8mm bungee cord (12m length) and 18 brass eyelets.Vehicles AffectedUniversal itemThis kit will fit many vehicles, it is impossible for us to list for all vehicles that our item will fit or to test on all vehicles / variants. Suitable for lorries, tippers, trailers, farm vehicles etc.Ideal vehicles for this product are as follows:• Iveco Daily• Ford Transit Tipper• Peugeot Boxer• Citroen Relay• Fiat Ducato You Will Receive1 x universal flatbed net complete with bungee cord & handy carry bag
Replace Your Broken Roof Trims on Mini Cabriolet Convertible Cooper S R52 R57 With This X8R Kit! X8R Ltd 2023-08-09 | The rubber strip will become cracked and begin to flake away. You may notice a build up of dirt in the void underneath the top edge of the boot hatch. Depending on how serious the leak is, there may even be some rust beginning to develop from where water has leaked past the seal which meets the canvas roof. These seals also act as a form of soundproofing, when they deteriorate you might notice an increase in wind noise from inside the cabin.THE FAULTThe factory installed weather strips on these cars tend to perish and become cracked over time when exposed to sunlight and adverse weather conditions. This can result in water leaking behind the chrome trim and cause corrosion to form on the inside of the metal panels. The original Mini seals are made from a rubber which becomes hard and brittle over time, resulting in them failing.THE SOLUTIONWe have developed our own profiled sealing strip designed to be fitted to your OEM chrome trims. Our seal enables you to renew the rubber seal on these chrome trims. Saving the vast expense of replacing the chrome trims, these are extremely expensive from BMW and used parts will have the same fault. Our seal is unique in the market and designed specifically for this fitment. Uniquely our seal has a "skirt" to cover all of the original seal. Some suppliers supply just rubber to replace the top section of the OEM seal that fails, this does not address the issue of the rest of the seal looking bad. Our seal uniquely covers and replaces the original to provide a perfect finish.Specially designed to apply pressure to the canvas seal, resulting in a tight seal to protect against water ingress.Our seal replicates the original style of the factory seal, maintains the bead that runs along the length of the seal, meaning that your new seals will look as close as is possible to OEM seals. Our seal uses VHB (Very High Bond) 3m adhesive tape to ensure a secure fit. We supply this as a complete kit to renovate your chrome trims. We include replacement stainless steel screws to replace the original mild steel ones. Sanding sponge and alcohol wipes to prepare the surface. VEHICLES AFFECTEDAll Mini convertibles, R52, R57 years 2004 through 2015.
How To Fix Your Exhaust Heat Shield! | X8R Exhaust Heat Shield Repair Kit X8R Ltd 2023-03-01 | Symptoms of FaultSymptoms of a failed exhaust heat shield mount may include but are not limited to:• Rattling exhaust when travelling upwards of 20mph.• Strong rattling when using throttle• Dragging or scraping noise coming from heat shield hanging off.• Hanging or loose fitted heat-shield visible from underside of car.The FaultExhaust fittings can easily fail due to various road conditionsRust and corrosion can cause your exhaust heat shield to come loose around the original fixings. They can cause unwanted rattling dragging or scraping from underneath the vehicle.Before our repair kit, the solution would be to replace the heatshield, however this can be costly and time-consuming (sometimes the exhaust will need to be removed to carry out this repair). Not forgetting that the fault will only happen again further down the line.The SolutionRepair your existing heat shield without taking it off the vehicleOur universal heat shield repair kit comprises of five stainless steel heat shield washers which are 50mm in diameter, covering the areas of the heat shield which have most likely rusted and come away from the original fixings. They are made from the same material that most heat shields are manufactured from and can be moulded in shape to bend to your original heat shield (if required).You will also receive five zinc-plated steel star locking washers (also known as underbody clips) which provide the stainless steel washers with a secure fit.Minimal tools are required to carry out this fix, so you can do it on your driveway at home!Vehicles AffectedUniversal itemThis kit will fit many vehicles, it is impossible for us to list for all vehicles that our item will fit or to test on all vehicles / variants.Part numbers:Equivalent to VW number N90335004 You Will Receive5 x Stainless steel heat shield washers5 x Zinc-plated steel star locking washers
X8R Land Rover Range Rover L322 Vogue Sport 3.6 TDV8 EGR Valve Repair Tool kit Set X8R Ltd 2022-12-12 | SYMPTOMS OF FAULTIs your Land Rover Range Rover or Range Rover Sport feeling sluggish? Short of power, slow off the mark?Suffering poor fuel consumption (MPG), turbo lag, rough idle, poor torque- slow engine pick up? Smokey exhaust?THE FAULTCarbon built up in your vehicles EGR system is restricting air flow.Carbon rich recirculated exhaust gasses enter the intake manifold, over time Carbon / Coke deposits gather in the EGR valve and manifold blocking air flow. Resulting in reduced fuel economy and vehicle performance. Common symptoms of failure include; rough engine running, decreased throttle response and loss of power / torque.THE SOLUTIONFit our EGR kit and allow your engine to breathe once more.Eliminate the risk of future carbon build ups in the EGR system. Improved torque with smoother pick up and improved fuel consumption, reduced turbo lag and less nasty exhaust fumes. Our blanking plugs are fitted with Viton O-rings suited to the fitting environment, do not trust Nitrile seals.Our kit comes with OEM spec gaskets for the exhaust manifold blanks, these are important for a good seal, equally importantly they keep the mounting bolts secure before fastening to ensure they do not drop in to the exhaust manifold! For off road / diagnostic use only.VEHICLES AFFECTEDLand Rover, Range RoverAll Vehicles With The 3.6ltr TDV8 EngineYOU WILL RECEIVE2x Intake Manifold Billet Anodised Aluminium Blanks fitted with Viton O-Rings 2x Exhaust Manifold Billet Anodised Aluminium Blanks2x Exhaust Manifold Blanks Captive Gaskets8x New EGR Screws For Blanks
X8R0249 Vauxhall/Opel 1.7 CDTi Injector Seal Replacement/Repair Kit X8R Ltd 2022-12-09 | SYMPTOMS OF FAULTYou may notice that your engine begins to run less smoothly, juddering or stuttering when idling and a noticeable drop in power output.You may notice oil leaks from various locations around the upper engine block.Oil may begin to leak into the cylinder resulting in blue smoke coming from the exhaust.THE FAULTVarious seals fail causing these faultsOver time rubber seals within the engine can become brittle and lose their sealing capabilities resulting in leaks in various locations around the engine.The common areas for these leaks to appear are:The rocker cover gasket, when this leaks your engine will begin to consume oil and you may notice a burning oil smell from the engine bay.Injector upper seals, these can fail and result in oil leaking from the top of the plastic rocker cover.Injector union seals, these can perish over time and result in a failure of the seal, which will cause rough running as well as causing an oil leak.Injector metallic seals, the engine relies on these seals to keep the combustion chamber sealed, if they fail then you will notice a drop in cylinder compression, as well as oil leaking onto the top of the piston, this could cause a puff of smoke when first starting the engine where oil has leaked through whilst the engine was off.THE SOLUTIONInstall our new seals and gaskets and cure these leaks and vehicle faultsOur kit is comprehensive, it contains all of the seals, gaskets, specialist tools and sealant that you will need.By renewing the old seals that have become brittle over time you can give your engine a breath of new life.Our kit uniquely includes parts that are unavailable from the main dealer enabling an effective repair without having to buy whole components such as the complete rocker cover.This type of maintenance often helps the engine run a lot smoother, if your existing seals have failed and allowed the engine to lose vacuum then your engine may be pre-maturely wearing.VEHICLES AFFECTEDVAUXHALL and OPELAll vehicles with the 1.7CDTi engine found in:Zafira 2005-2014Astra J 2009-2015Corsa D 2006-2014 (131hp)Mokka/Mokka X 2012-currentAssociated engine codes:A17DTC, A17DTE, A17DTJ, A17DTF, A17DTS, A17DTRYOU WILL RECEIVE4 x Injector Union Seals - Equivalent to OEM 973763044 x Rocker cover injector seals (not offered by OEM)1 x Rocker Cover Gasket - Equivalent to OEM 560725210 x Rocker Cover Bolt Seals (not offered by OEM)4 x Injector Base Metallic Gaskets - Equivalent to OEM 973243911 x Injector Pocket Cleaning Tool - Equivalent to EN-476328 x Injector Pocket Cleaning Felt Pads Equivalent to EN-476321 x Injector Alignment Tool - Equivalent to EN485601 x Complete Blanking and Plugging Kit - EN63681 x Pack of RTV gasket
Van Sliding Door Stop Wedge Stopper Kit For Campervan Motorhome Install Instruction Guide X8R Ltd 2022-10-03 | SYMPTOMS OF FAULTSide loading door closing or being moved by the wind. Door moving on an incline whilst camping.SUMMARY OF FAULTWhilst camping it can be preferable for the side loading door to be left part open for ventilation / cooking purposes.SUMMARY OF OUR SOLUTIONOur unique design precision engineered billet aluminium wedge is designed to fit perfectly within the runner of a van door. Our wedge allows the door to be opened and secured in your position of choice without having to purchase more expensive hinge systems.Unique to our design the underside of our Van Door Stop Ramp is machined with a diamond knurled finish to ensure a good grip between the runner and the ramp, the perfect solution for the best bond.Full kit including high quality Loctite branded Epoxy adhesive and emery paper for preparing the runner surface.Deep dished design for good security of the roller. High grade anodized aluminium for life long use.If you require multiple stop points you can install multiple wedges.Easy to fit, no drilling or screwing required.VEHICLES AFFECTEDThis part will be compatible with almost all sliding van doors that utilise a roller and runner style system. E.g. VW T5, Mercedes Sprinter, VW Crafter, Ford Transit, Peugeot Boxer, Citroen Relay, Fiat Ducato, Iveco Daily.YOU WILL RECEIVE1 x Aluminium Sliding Van Door Stop Ramp1 x Epoxy glue packet1 x Epoxy mixing pallet1 x Mixing stick1 x Piece of emery cloth
X8R0239 Audi VW Porsche 2.7 3.0 Swirl Flap Delete Kit X8R Ltd 2022-08-15 | The Fault:The actuator motor on the intake manifold over rotates; triggering fault codesWhen the Engine Control Module (ECM) detects that the intake manifold is not functioning properly it will normally illuminate the check engine light. The intake manifold control valve/position sensor (which is typically located at one end of the intake manifold) provides values which help the vehicle’s Powertrain Control Module (PCM) control the amount of air being allowed into fuel injected engines at various RPMs. Using information from the sensor, The Intake Manifold Runner Control (IMRC) determines the position of the throttle body plates (commonly called flapper valves) and adjusts them to adapt to engine load variations. This ensures a correct mixture of fuel and air by limiting the amount of air that can pass though the engine. The P2015 code means that there is out of range data from the sensor.The P2020 code is the fault code associated with Bank 2 for the same issue.If your vehicle has a P2015 and/or P2020 error it is very likely the main dealer will look to fix this issue with one or two completely new intake manifolds at significant cost. The fault however usually lies with the actuator motor on the intake manifold(s). There are two plastic limiting stops on the large cog within the motor. These are delicate and inevitably wear, allowing the motor to over rotate which triggers the P2015/P2020 error.Our repair brackets can be installed very easily providing a solid limit for the actuator motors - curing these faults for the life of the vehicle. There is no need to replace the complete manifolds / actuator motors which would only fail again.The Solution:Install our swirl flap kit to remedy this issue and prevent future faults from occurring.Our Swirl Flap Delete Kit comprises of every component you will need to remedy this issue. Our Bearing and Pull Rod Blanks are made from 304 Stainless Steel to provide longevity of the part. The Pull Rod Blanks have a design unique to X8R Ltd, combined with the Viton O Ring and 2 OEM design fitting clasps to guarantee most secure fit.The X8R kit comes complete with 2 OEM Intake Manifold Gaskets, which are recommended to be changed at the same time as fitment.We recommend to fit both manifold kits at the same time as the two manifolds work together so it is preferable for them both to have the same limit.Vehicles AffectedVolkswagen:Touareg 2004-2014Phaeton 2004-2013Audi:A4 2004-2013A5 2007-2013A6 2004-2012A7 2004-2012A8 2003-2013Q5 2004-2014Q7 2006-2014Porsche:Cayenne 2004-2012Engine codes: CAMA, CAMB, CANA, CANB, CANC, CAND, CAPA, CARA, CASA, CASB, CASC, CASD, CATA, CCLA, CCMA, CCWA, CCWB, CDYA, CDYB, CDYC, CEXA, CGKA, CGKB.You Will Receive:12 x Bearing Blanks2 x Pull Rod Blanks2 x Viton O Rings2 x Pull Rod Blank Clasps2 X OEM Intake Manifold Gaskets
X8R0238B Vivaro Trafic NV300 Talento Internal Door Guard X8R Ltd 2022-06-21 | The problem:Many people are looking to convert their vans into mobile camping units where safety is of course a top concern.There is currently no effective way of locking the rear doors from the inside of the van, meaning that the van could potentially be opened form outside whilst people are inside.Our solution:Install our internal van door lock to allow for quick and easy locking from inside.Our solution fits onto the existing components on the van door, meaning that you will not have to damage your existing van doors in any way to install our product.The brackets are made from high grade marine stainless steel, meaning they are resistant to weathering.The finish of the product is brushed stainless steel and sports our company’s “X” logo which will keep the interior of your van looking stylish.Our product will contain a quick release locking pin; however it is compatible with most off-the-shelf padlocks if you wish to use your own.You will receive:One quick release locking pin.Both halves of the X8R internal van door lock.2 x isopropyl alcohol wipes for preparing the work area.Vehicles affected:Fiat Ducato (2006-2014)Peugeot Boxer (2006-2014)Citroen Relay (2006-2014)Compatible with all models with H1 and H2 roof height.Citroen rear door part numbers: left: 8702 A3, 16 216 821 80. Right: 8703 A5, 16 813 185 80
How To Prevent a Break-In on Your Vivaro Trafic NV300 Talento! | X8R Door Lock Shield Kit X8R Ltd 2022-06-21 | The problem:It is very common for thieves to attempt break-ins on these vans by drilling a hole through the rear door to access the internal mechanisms of the lock and open the door, thus being able to take whatever is stored in the back of the van. If your van has been broken into, the usual resolution is to replace the whole door, which is very expensive and can be difficult to source. You may even need to spray the door to match your van. If you are looking for a deterrent, a common solution is an alarm system. These are also expensive and may not deter a thief- by the time the alarm goes off they might already be in the van and stealing your tools!Our solution:Rather than replace your door or install an expensive alarm system, install the X8R Door Lock Shield Kit. This comprehensive kit will deter thieves from breaking into your vehicle by adding an extra layer of protection to your door. Our kit is easy to fit and can be done within an hour. It also comes with a 19mm holesaw to drill into your door, so you don’t have to buy an entire holesaw kit. Our shield is made from anti-cut & drill 2.5mm stainless steel, which is over twice the thickness of the skin of the OEM doors. The shield also comes with a closed cell foam gasket which sits flush between the door & the shield, creating a water-tight protective barrier to prevent rust and corrosion. Vehicles affected:Renault Trafic 2014-Fiat Talento 2014-Nissan NV300 2014-Vauxhall Vivaro 2014-You will receive:1 x Stainless steel exterior protective shield1 x closed cell foam gasket8 x washers8 x Nyloc nuts1 x grease pot1 x 19mm holesaw
X8R Internal Van Door Lock for Fiat Ducato | Citroen Relay | Peugeot Boxer X8R Ltd 2022-05-25 | The problem:Many people are looking to convert their vans into mobile camping units where safety is of course a top concern.There is currently no effective way of locking the rear doors from the inside of the van, meaning that the van could potentially be opened form outside whilst people are inside.Vehicles affected:Fiat Ducato (2006-2014)Peugeot Boxer (2006-2014)Citroen Relay (2006-2014)Compatible with all models with H1 and H2 roof height.Citroen rear door part numbers: left: 8702 A3, 16 216 821 80. Right: 8703 A5, 16 813 185 80Our solution:Install our internal van door lock to allow for quick and easy locking from inside.Our solution fits onto the existing components on the van door, meaning that you will not have to damage your existing van doors in any way to install our product.The brackets are made from high grade marine stainless steel, meaning they are resistant to weathering.The finish of the product is brushed stainless steel and sports our company’s “X” logo which will keep the interior of your van looking stylish.Our product will contain a quick release locking pin; however it is compatible with most off-the-shelf padlocks if you wish to use your own.You will receive:One quick release locking pin.Both halves of the X8R internal van door lock.2 x isopropyl alcohol wipes for preparing the work area.
Suzuki Jimny 1998-2018 Kingpin Rebuild Refurbishment Repair Kit X8R Death Wobble Vibrating MOT Fail X8R Ltd 2022-03-17 | The problem:The first generation Suzuki Jimny have a 4 wheel drive suspension set-up using kingpins and a swivel joint system, although a fairly good set-up they are prone to oil leaks and the kingpins and bearings fail when excessively used off-road. Not only are these faults MOT failures, they are also dangerous if driven when the faults become excessive- known as the “death wobble”. Symptoms of the fault:Steering “shimmy” AKA “death wobble” the steering wheel shaking usually around 35-45mph (60-80mk/h), can be anything from a slight shake to a violent steering wheel shake. Oil/grease leaking from the swivel joints. Vertical play in front wheels when hovering above ground.Vehicles affected:Suzuki Jimny 1998-2018 (JB23/JB33/JB43/JB53)Associated part numbersKingpins – 45610-63002Bearings – 09265-15006Swivel seal – 45120-81A04Oil seal – 09283-26016Our solution:We have made a kit that comprises of all the components you need to refurbish one side of your front axel (for both sides, purchase two kits). These kits are few & far between, with some kits comprising of unnecessary parts. The X8R kit contains unique items such as the bungs to pop over the vacuum lines to prevent any dust or corrosion from entering the system, in addition to the most highly recommended high-temperature and highly resistant CV grease from Maxima Racing Oils. This grease combined with the brand new seals limits the possibility of water ingress into the bearings and swivel hub.You will receive:1 x Swivel Seal 2 x Kingpin Bearings2 x Kingpins1 x Driveshaft oil seal1 x 454g Maxima Waterproof Grease1 x circlip for the driveshaft2 x M8 disc locating bolts8 x bolts for the kingpins 8 x swivel seal bolts
BMW Steering Rack Bush Repair Kit and Three Pin Tool| X8R Broken Noisy Clunky Vibrating X8R Ltd 2022-01-25 | Important!We state 70nm of torque when tightening the locking cap, this will vary between models so be sure to check your cars specific torque setting before you tighten this.The symptomsClunking noise from steering when turning into full lock, clunking noise when driving over bumps, speed bumps and potholesThe problemOver time the thrust bush within the steering rack disintegrates & wears down, this causes excess noise coming from the steering. BMW has recognised this issue and introduced a “quality improvement” kit- a OEM kit that includes an improved design bush, spring, bung, jubilee clamps for the steering gaiters and a replacement locking screw cap complete with o ring. The locking screw cap also requires a specialist tool, which can also be purchased from BMW but at a hefty price tag. You also require the BMW-spec steering grease. Up until now there was nowhere in the UK selling this complete kit.Our solutionTo make the fix as easy as possible, we have created our kit where all the components can be purchased from the same place. Our complete kit comes with the OEM BMW improvement kit (which comes with 2 years BMW warranty), the OEM BMW grease, and our X8R Steering Rack Tool. Vehicles affectedBMW Applications:1 Series (F20, F21) 2011-20193 Series (F30, F31, F34, F35) 2011-20194 Series (F32, F33, F36) 2013-2020X1 (F48) 2015-presentX3 (F25) 2010-2017Mercedes Applications:C Class (W205) 2014-2021S Class (W222, C217, A217) 2014-2020OEM Part Numbers: 32106891974 – rack repair kit83232208093 – steering greaseYou will receive1 x BMW & Mercedes Steering Rack Socket1 x BMW OEM bush repair kit equivalent to 321068919741 x tube of OEM BMW steering grease equivalent to 83232208093
Jaguar Door Handle Gasket Repair | Improved Design for Leaking Seal X8R X8R Ltd 2021-11-30 | The problemThe gasket on the door handle is made from plastic which becomes brittle and breaks over time. The seal will then allow dirt and water ingress into the interior of the door card which can affect electrics. It also looks old and parts of the seal can look broken around the exterior door handle.Symptoms of the faultParts of seal missing or broken around door handle, electrical issues with window, speaker or door locking mechanismVehicles affectedXJ6 XJ8 XJ12 XJR X300 X308 models 1994-2002 (VIN range 720125 through to 878717, F00001 through to F59525)XK8 XKR models 1996-2006 (VIN range 000001 through to 042775, A00001 through to A99999)Suitable for coupe & convertible.Also suitable for left hand drive & right hand drive models.Associated part numbersJLM-12035Our solutionOur improved design gasket is made from closed cell foam which is water resistant, preventing breakdown from water and dirt making it longer lasting than the original gasket. The gasket is a simple, oval design making it easy to fit.Our kit also comes with alcohol wipes to clean off any built-up grime from the failure of the OEM gasket, as well as a tube of RTV silicone sealant to stick the gasket to the handle and prevent any future leaks.You will receive2 x Foam door handle seals2 x Alcohol wipe1 x RTV silicone sealant
X8R Pick-Up Truck Replacement Handle Fitting Guide | For CarryBoy, SJS, ADventurer. AT Avenger X8R Ltd 2021-10-21 | The problemHard top handles often need replacing due to a single component within the mechanism failing, such as the spring or the lock cylinder. Or the handle might need replacing due to losing the keys.Handles from the original manufacturers are expensive and can also have long lead times if on back-order. Automotive locksmiths are also pricey. Symptoms of the faultOriginal key no longer working, loose handle, no longer locking the hatchVehicles affectedThis is a universal replacement handle which will fit any hardtop which does not have a recessed handle (for example, this will not fit Snugtop Canopies). It fits brands such as:• Carryboy• SJS• Adventurer• AT Avenger• Aeroklas• And other hardtops built from factory for Navara, L200 etcThe length of the handle itself does not matter; the important measurement is the distance between the sections of the handle that slot into the glass/tailgate hatch. The measurement between this section is 82mm. For all measurements, please see the guide in the images of this listing. If you are unsure if this handle is correct for your vehicle, please send us a photo of your handle.Our solutionInstead of purchasing a new handle from the manufacturer of your hard top (which can be very pricey!), purchase our universal replacement handle instead. Our replacement handle is made of high-quality materials which look exactly like the OEM handles, for a fraction of the price. If you have lost your keys, or perhaps the lock cylinder has seized leaving the key redundant, then you will find that replacing your handle with our X8R replacement handle must more cost-effective. You will receive1 x Replacement Hard Top Handle including the following components:• Handle• Base• 2 x keys• Gasket for base• Gasket for locating stud• 30mm nut• Phillip’s head screw• 10mm bolt• 2 x washers• 1 x spring• 1 x spring holding plate• 1 x spacer• 1 x latch locking rod platePlease note we do NOT sell these components separately, and any orders returned with components missing will not be refunded
Ford Transit MK7 2000-2014 Replacement Door Seals | Leaking Broken Rubber Rust Split X8R Ltd 2021-10-18 | Symptoms of FaultRusted door sills, broken or split door seals, leaks or puddles in footwellsThe FaultThe rubber door seals often deteriorate which can lead to severe rust.The rubber seals that surround the doors on the MK7 Ford Transit often split, deteriorate and come away from the doors, resulting in water ingress sitting on the door sills and in the footwells, which can lead to severe rust. The seals also look poor once they start to deteriorate.The seals also have a very loose fit and can easily come away from the door sills, they are not fixed on with glue and the rubber loses its grip over time. Therefore, the seals can completely come away, leaving the door sills exposed which can cause damage.New seals from Ford are very expensive and retail for over £120 + VAT. This is a costly fix for a seal that will have the same issue recurring time & time again.Our solutionInstall our improved design door seals to prevent these issuesWe have introduced new door rubbers which are metal reinforced, they hold a strong grip onto the door sills and create a protective bond against any rust, corrosion or damage. The seals can be installed in a matter of minutes, with almost no tools being required. They instantly improved the appearance of your Ford Transit.Vehicles affectedMK7 Ford Transit (all models) (2000-2014)Part numbers affected1555296You will receive1 x improved design front door seal (4.2m length in total)
Volkswagen T5 T5.1 Cup Holder Insert | Broken Snapped Spring Mechanism X8R Ltd 2021-09-27 | The problemThe OEM Volkswagen cup holder works by retracting to & from the dashboard, when it pops out there are two flaps which hold two drinks. However the flaps work on a spring mechanism which often breaks. The flaps also put too much pressure on paper cups (such as those from drive-thrus) and can cause them to spill.Symptoms of the faultBroken cup holder mechanism, spilling drinks, rattling cup holderVehicles affectedVolkswagen Transporter T5 and T5.1 (2003-2016)Including Caravelle and CaliforniaAssociated part numbers7H2 858 6017H2 857 321KOur solutionWe have created an improved design cup holder insert which has been injection molded for precision and quality. The insert also makes it far easier to insert a drinks cup or bottle whilst drivingYou will receive1 X ABS injection molded cup holder insert
Ford Heated Seat Button Repair Lever Kit X8R (Fiesta, Courier, Transit, Ranger etc) X8R Ltd 2021-08-17 | Symptoms of the faultSymptoms of the fault are very obvious. The button can be stuck in the On or Off position, unable to be pressed in. When being pressed in, it doesn’t stay in position and springs back out. No resistance within the button.The faultIt is common for the heated seat mechanism to bend or break inside the buttonThe heated seat switches on various Fords become inoperable due to the metal lever that guides the button up & down breaking or bending. The small connectors can snap off, the lever itself can bend / misshapen, or the whole lever itself could snap in half. This is due to it being die-cast from thin metal, thus weak by design.A new button costs around £50 from Ford, our kit is just a fraction of the cost, is incredibly easy to install and will stop the fault occuring again.Vehicles affectedFord Transit MK8 (2014 Onwards)Custom (2012 Onwards)Courier (2014 Onwards)Transit Connect (2014 Onwards) Cougar (1998 - 2001)Escort MK6 (1995 - 2001)Fiesta (1996 Onwards)Mondeo MK1 (1993 - 1996)Ranger MK5 (2012 Onwards)Streetka (2003 - 2007)Part numbers affected6706942Our solutionA much stronger lever made from machined billet stainless steelOur repair kit consists of a replacement lever for the internals of the button. Replacing this instead of the entire button is not only cost-effective but also provides a long-term solution as the OE lever will fail again.Our improved design is made from billet stainless steel making it far stronger, designed to last the life of the vehicle. You will receive1 X billet stainless steel repair bracket
Tail Light Seal Leaking Replacement X8R | Toyota AYGO Citroen C1 Peugeot 107 Water Ingress Foam X8R Ltd 2021-07-01 | The problem:The foam gasket that the tail light comes attached to from factory disintegrates over time due to its poor structure. This allows water to enter through the gasket and into the boot, causing puddles of water on the boot floor.Symptoms of the fault:Water leaking through the tail gate or rear body via the tail lights, damp boot carpet, puddles of water in the bootVehicles affected:Citroen C1 Mk1 2005-2014Peugeot 107 MK1 2005-2014Toyota Aygo MK1 2005-2014Associated part numbers6350 X9 & 6351 X9 - tail lights for Citroen C116 079 905 80 & 16 079 903 80 - tail lights for Peugeot 10781551-0H080 & 81561-0H080 - tail lights for Toyota AygoOur solution:We have designed & created new and improved tail light seals made of closed cell foam which are thicker than the OEM seals. They are also resistant to water to prevent leaks, and also reduces moisture & condensation entering the light unit and vehicle itself.Our seal has a strong, adhesive backing so no messy glue is needed. This fix requires minimal tools and is easy to fit.
High Level Brake Light Seal Leaking Replacement X8R | Toyota AYGO Citroen C1 Peugeot 107 X8R Ltd 2021-07-01 | The problemThe foam gasket that the third brake light comes attached to from factory disintegrates over time due to its poor structure. This allows water to enter through the gasket and into the boot, causing puddles of water on the boot floor.Symptoms of the faultWater leaking through the top of the tailgate, damp boot carpet, puddles of water in the boot.Vehicles affectedCitroen C1 Mk1 2005-2014Peugeot 107 MK1 2005-2014Toyota Aygo MK1 2005-2014Associated part numbers1606372780Our solutionWe have designed & created a new and improved high level brake light seal made of closed cell foam which is thicker than the OEM seal. It is also resistant to water to prevent leaks, and also reduces moisture & condensation entering the light unit and vehicle itself.Our seal has a strong, adhesive backing so no messy glue is needed. This fix requires minimal tools and is easy to fit.
Renault ABS Plate Shield Sensor Repair X8R | Megane Scenic Laguna Espace Grand Scenic X8R Ltd 2021-06-16 | Symptoms of the faultABS light on dashboard, rusted or disintegrated ABS plate, ABS sensor hanging loose. Sometimes the plate is rusted away to the point where it is completely missing.The problemThe ABS plates that sit over the wheel hub corrode and disintegrate over time, thus reducing the connectivity to the ABS sensor and generating an ABS fault code. These plates are not available to buy separately as they are built into the rear axle and Renault garages will charge over £1000 for a new axle plus labour. Even scrap yards are not willing to sell the plates separately as they can make more money selling the complete axles. Vehicles affectedCentre diameter 40mm:Renault Megane II (2002-2009) (Convertible, Estate, Hatch)Renault Scenic II (2002-2009) (not Grand Scenic)Centre diameter 45mm:Renault Espace IV (2001-2009)Renault Laguna II (2002-2009)Renault Grand Scenic II (2002-2009)Renault Megane III (2007-2018)Renault Scenic III (2007-2018)Renault Grand Scenic III (2007-2018)Renault Laguna III (2007-2018)Associated part numbersRear axle: 430008639R (45mm)77014770757701477073 (40mm) Our solutionOur ABS plates are a much more cost-effective solution to this common and simple issue. We have designed & created our own plates out of marine grade stainless steel to prevent any corrosion like the original unit. They also have two indents for spot welds, this is because the knuckle itself may have surface corrosion, affecting a secure fit for the new ABS plate, if this is the case then you can spot weld it into place so the ABS sensor does not become lose. You will receive1 or 2 x ABS Plate made of marine grade stainless steel
Ford Heated Seat Button Repair Lever Kit X8R (Fiesta, Courier, Transit, Ranger etc) X8R Ltd 2021-06-01 | Symptoms of the faultSymptoms of the fault are very obvious. The button can be stuck in the on or off position, unable to be pressed in. When being pressed in, it doesn’t stay in position and springs back out. No resistance within the button. The faultThe heated seat switch on various Fords become inoperable due to the metal bracket that guides the button up & down can break or bend. The small connectors can snap off, the bracket itself can bend/misshapen, or the whole bracket itself could snap in half. This is due to it being made of die-cast metal which can easily break over time. A new button costs around £50 from Ford, but our kit is just a fraction of the cost and incredibly easy to install.Vehicles affectedFord Transit MK8 (2014 Onwards)Custom (2012 Onwards)Courier (2014 Onwards)Transit Connect (2014 Onwards) Cougar (1998 - 2001)Escort MK6 (1995 - 2001)Fiesta (1996 Onwards)Mondeo MK1 (1993 - 1996)Ranger MK5 (2012 Onwards)Streetka (2003 - 2007)Part numbers affected6706942Our solutionOur repair kit consists of a replacement bracket for the internals of the button. Replacing this instead of the entire button is not only cost-effective but also provides a more reliable long-term solution as the OE button regularly fails over time. Our improved design is made from billet stainless steel making it stronger and reliable. You will receive1 X billet stainless steel repair bracket
Dummy Door Lock Fitting Guide Van Commercial Vehicle Added Security X8R Ltd 2021-05-26 | The problemUnfortunately, it is becoming more & more common for vehicles to be broken into, especially vans since they often carry expensive tools and machinery. Thieves will often drill into doors to access OEM locks to open them from the inside, leaving the owner with a damaged vehicle and no tools, thus an expensive bill.Vehicles affectedMostly vans, lorries and truck owners are affected by the common problem of having their vehicles broken into, but this universal dummy lock can be fitted to any vehicle, including caravans, motorhomes, passenger vehicles etc.Our solutionOur dummy door lock is made of nickel-plated brass, meaning that it does not tarnish or discolour in the sun or rain. It is machined down from a Euro cylinder lock, giving it an authentic look. The rubber surround is backed with 3M VHB double sided tape which is the strongest tape on the market so it will stay bonded to the vehicle for as long as necessary.Within our kit you will receive a pair of dummy door locks, one for a side door and one for the back door. You will receive:1 or 2 x X8R Dummy Door Lock (available to purchase individually or in pairs)
Toyota AYGO Peugeot 107 Citroen C1 Rear Door Seal Leak Fix Seal Kit Seals Install Guide X8R Ltd 2021-04-15 | This video demonstrates the installation of our additional door seals for the Citroen C1, Peugeot 107 & Toyota AYGO. Both seals are available to purchase separately.Symptoms of fault Water leaking in to the boot and footwells. Wet carpets and mats. Rattling / whistling noises, excess wind and road noise. Rattling sounds from doors and tinny sound when closing doors. The fault It is a very common fault for leaks to occur on these vehicles, with water entering and pooling in the boot and footwells. The door seals on these vehicles are poorly designed from the outset and get worse with age. These seals both on the tailgate and doors sit deep within the mating surfaces of the doors and body of the vehicle. This means a large volume of water can pool above the seals. This overwhelms the seals, entering the back of the seals and causes these leaks. As the OEM seals sits so far from the outer edge of the doors this means the outer edges of the doors close directly on the metal of the vehicles body creating a tinny metallic sound when closing the doors. The solution Our seals sit closer to the edge of the mating surfaces of the doors, preventing the main door seals from being overwhelmed and leaking. Unique in design our seals fasten to the outer edge of the vehicles body where the doors close. Our seals are extremely easy to fit, just peel off the 3M sticky tape on the reverse and fit in the positions shown in our video and pictorial instructions. The seals close up the gap between the body and the door stopping water pooling on the main door seal, preventing leaks. Also included is a replacement boot seal, this is a direct replacement for the OEM part, this slots in to place as per the original, our seal is improved with a larger diameter to prevent leaks in to the boot.Alongside this we also supply an additional top seal which works in the same way as our door seals, providing an external seal, preventing pooling of water within the tailgate. Our seals are a direct fit and can be fitted in under 20 minutes. Our seals are cut to size ready to fit, we also include 2x alcohol wipes to clean the vehicles body prior to fitting our seals. Vehicles affected Citroen C1 MK1 2005-2014 Toyota Aygo MK1 2005-2014 Peugeot 107 MK1 2005-2014 Associated part numbers:B000651380, 62331-0H014, 8707C7, 9025A6, 9025AK, 9025A8, 9025AL. You will receiveX2 Additional Door SealsX2 Alcohol wipe
Toyota AYGO Peugeot 107 Citroen C1 Boot Tailgate Seal Leak Fix Seal Kit Seals Install Guide X8R Ltd 2021-04-15 | This video demonstrates the installation of our improved boot seal and additional boot seal for the Citroen C1, Peugeot 107 & Toyota AYGO. Both seals are available to purchase separately.Symptoms of fault Water leaking in to the boot and footwells. Wet carpets and mats. Rattling / whistling noises, excess wind and road noise. Rattling sounds from doors and tinny sound when closing doors. The fault It is a very common fault for leaks to occur on these vehicles, with water entering and pooling in the boot and footwells. The door seals on these vehicles are poorly designed from the outset and get worse with age. These seals both on the tailgate and doors sit deep within the mating surfaces of the doors and body of the vehicle. This means a large volume of water can pool above the seals. This overwhelms the seals, entering the back of the seals and causes these leaks. As the OEM seals sits so far from the outer edge of the doors this means the outer edges of the doors close directly on the metal of the vehicles body creating a tinny metallic sound when closing the doors. The solution Our seals sit closer to the edge of the mating surfaces of the doors, preventing the main door seals from being overwhelmed and leaking. Unique in design our seals fasten to the outer edge of the vehicles body where the doors close. Our seals are extremely easy to fit, just peel off the 3M sticky tape on the reverse and fit in the positions shown in our video and pictorial instructions. The seals close up the gap between the body and the door stopping water pooling on the main door seal, preventing leaks. Also included is a replacement boot seal, this is a direct replacement for the OEM part, this slots in to place as per the original, our seal is improved with a larger diameter to prevent leaks in to the boot.Alongside this we also supply an additional top seal which works in the same way as our door seals, providing an external seal, preventing pooling of water within the tailgate. Our seals are a direct fit and can be fitted in under 20 minutes. Our seals are cut to size ready to fit, we also include 2x alcohol wipes to clean the vehicles body prior to fitting our seals. Vehicles affected Citroen C1 MK1 2005-2014 Toyota Aygo MK1 2005-2014 Peugeot 107 MK1 2005-2014 Associated part numbers:B000651380, 62331-0H014, 8707C7, 9025A6, 9025AK, 9025A8, 9025AL. You will receiveX1 Improved design tailgate seal X1 External tailgate sealX1 Alcohol wipe
METAL Vauxhall Opel Mokka Handbrake Handle Release Replacement Button Kit Install Instructions Guide X8R Ltd 2021-01-27 | The problemThe OE handbrake button often breaks within the internal mechanism of the handbrake, resulting in the handbrake not working as it should. The button’s arms that slot into the internals of the mechanisms or the shoulder on the bottom of the button can often snap resulting in the button becoming lodged in place and unable to press in or out, or it can come loose and fall out entirely. This is because the OE button is made of very thin plastic and is not made to last the span of the vehicle’s life.Symptoms of the faultThe handbrake button becoming stuck in place or falling out, resulting in the handbrake becoming in operable and being stuck in the upright or downward position. The main Vauxhall dealers will say you will need the whole handbrake unit replacing as the button is not a spare part. This will cost hundreds with labour as the centre console must be removed in order to do so. Vehicles affectedVauxhall & Open Mokka J13 2012-2019Part numbers affectedHandbrake lever: 951379669527893842371925Handbrake handle:9527894942371932Please note there is no OE part number for the button as this part is not available separately from Vauxhall.Will fit all Mokkas within this age range regardless of interior colour or trim. It will also fit left hand drive & right hand drive vehicles. If unsure if this design will fit please email us a photograph of your handbrake to sales@x8r.co.ukOur solutionOur improved button is of the exact same design as the OE button, however it is made of alloy metal which strengthens the button meaning it will not break inside the mechanism. This solution will last the lifetime of the vehicle and is also cost-effective against the cost of fixing the unit at the main dealer.This can be fitted while the handbrake is still on the vehicle, meaning there is no stripping of interior components making the job very easy to carry out.You will receive1 x metal handbrake button1 x replacement spring
BMW 1 Series E81 E82 E87 E88 Center Console Cup Drinks Holder Instruction Install Fitting Guide X8R Ltd 2020-12-15 | The ProblemMost 1 Series vehicles do not come with the cup holder in the centre console as it was an optional extra from the factoryThe BMW 1 Series does not come with a centre console cup holder unless selected at factory. From factory you could select a centre console where the the cup holder was molded into the design. If this option was not selected at factory the only solution until now was to replace the whole centre console with this type, this is both time consuming and can be costly, especially as trims vary. This has led to people fitting window or vent mounted cup holders, both far from ideal and the vent solutions often damage the vent.Our SolutionOur cup holder fits directly in to the centre console, looks OEM and provides a cup holder without ruining the look of the interior.Our cup holder is a direct fit and simply lowers in to the centre console. Our part is designed to look as close as possible to the OE cup holder. Injection moulded for a perfect fit and finish, in Black ABS to match the original colour of the interior. No need to file, fill, or paint like 3D printed alternatives available.Unique in design our parts comes with 3 rubber grips in each cup holder recess to grip the cup. Adding more support and reflecting the design of the OE centre console with the cup holder.Our part comes complete with 3M adhesive tape to retain the cup holder in position, please check out our video to see how easy it is to fit.As our part comes with the rubber grips it does retain the cups, we recommend allowing the 3M tape to set overnight to fully retain the cupholder. Adhesive tape is only so good, if wishing to use the cupholder with the grips we recommend bonding the cup holder in to the centre console so it can't be pulled loose. Alteratively the rubber grips can also be removed so you can run the cupholder without.Vehicles affected1' E81 (2006-2011)1' E82 (2006-2013)1' E87 (2003-2007)1' E88 (2006-2013)Associated part numbers51169110513-51169110515, 51166953485-51166953487Will fit all transmissions / engines / optional extras.Please note, this will ONLY fit right hand drive models.You will receive1 x X8R cup holder complete with rubber grips and 3m tape.
BMW Mini Cooper S R52 R53 W11 Auxiliary Serpentine Drive Belt Changing Lever Lock Tensioner Tool Kit X8R Ltd 2020-12-15 | The ProblemA specialist tool is required in order to remove the auxiliary belt.The serpentine auxiliary belt is located in a very narrow & limited access section of the engine bay, making the belt very difficult to change without stripping major components from the engine. The belt is due to be changed every 60,000 miles (but should be replaced sooner if showing any signs of age or cracking). Or it may need to be removed to service components such as the supercharger, air conditioning compressor, water pump or alternator.The solution up until now was to purchase one of the several tools available online, however they can either be very costly or come with many complicated components, or pins that are difficult to locate in to the tensioner, making changing the belt more difficult than it needs to be.The SolutionOur tool can be used to easily release & replace the auxiliary beltOur kit is simple to use, with the main changing tool being custom manufactured at the correct angles & comes with a soft, cushioned handle for ease of use. The tool is precision machined to the perfect shape to marry up to the tensioner, allowing you to push against the broadest section of the tensioner to release, rather than trying to locate and push against the tensioner in the two small holes in the tensioner. Our tool is manufactured from Steel and is Bright Zinc plated, made in the UK for a lifetime guarantee.The kit also comes with a tensioner pin retaining tool, this is basically a correctly sized screwdriver angled to the correct shape for easy retaning of the tensioner pin. A lot of kits on the market come with a small Allen key or pin, which can be very fiddley and tricky to push in. Our tool as it is the perfect shape, long and with a handle it makes install in the tensioner pin far easier.Vehicles affectedSupercharged MINI Cooper S Models:BMW Mini Cooper S R52 convertible (2002-2008) BMW Mini Cooper S R53 (2000-2006) (Including JCW Models)Supercharged BMW Mini engines with engine code W11Will fit all variants with/without air conditioningAssociated part numbersPoly V-Belt 11287545120Tensioner 11287509476, 11288620210Pulley 11287570810BMW workshop tool 118410You will receive:1 x Zinc plated Steel auxiliary belt changing tool1 x Tensioner pin retaining tool
Garage Door Floor Threshold Weather Seal Rubber Draught Excluder Rain Weather Shield Install Guide X8R Ltd 2020-06-10 | The fault Water, leaves, debris, animals entering your garage through the gap between your garage door and the floor. Water entering garage during heavy downpours. Less than perfect garage floor surface so poor seal with garage door. Drafts and thermal heat loss through garage door. The solution Our unique design heavy duty garage door threshold seal is the perfect solution to prevent ingress of water and leaves in to your garage. Our threshold is fitted directly behind or under the garage door, the garage door mates to our threshold surface producing a watertight seal. Preventing the ingress of water, leaves, mud, rodents and debris and improving thermal efficiency by removing drafts of cold air. Whether protecting your vehicle, tools, home gym, home office or whatever the use you can rely on our threshold to keep contaminates out. Our seal is flexible this is essential as most garage floors aren’t perfect and flat, UV stable so won’t be damaged by sunlight, odour free and keeps its flexibility, even when in constant contact with water. Suitable for most door styles including manual and automatic. Up and over, sectional, roller shutter and side hinged garage doors. Our seal features unique grooves on the reverse to allow efficient adhesion and sealing with our selected hybrid adhesive. These grooves vary in width and depth to provide the very best adhesion and seal. Working with our specially selected hybrid adhesive and sealant this provides the perfect watertight seal between our threshold seal and the floor. Retaining flexibility in its design but providing permanent adhesion this is designed to allow you to drive over the seal with no issue. With a working temperature of -40°C - +100°C this is the perfect material to use. We have designed our seal with an eye-catching yellow line along the length of the threshold, providing a visual reminder to prevent trips. You will receive • Threshold seal in selected length.• High quality branded hybrid adhesive and sealant.
Toyota AYGO Peugeot 107 Citroen C1 Door Boot Tailgate Seal Leak Fix Seal Kit Seals Install Guide X8R Ltd 2020-06-10 | Symptoms of fault Water leaking in to the boot and footwells. Wet carpets and mats. Rattling / whistling noises, excess wind and road noise. Rattling sounds from doors and tinny sound when closing doors. The fault It is a very common fault for leaks to occur on these vehicles, with water entering and pooling in the boot and footwells. The door seals on these vehicles are poorly designed from the outset and get worse with age. These seals both on the tailgate and doors sit deep within the mating surfaces of the doors and body of the vehicle. This means a large volume of water can pool above the seals. This overwhelms the seals, entering the back of the seals and causes these leaks. As the OEM seals sits so far from the outer edge of the doors this means the outer edges of the doors close directly on the metal of the vehicles body creating a tinny metallic sound when closing the doors. The solution Our seals sit closer to the edge of the mating surfaces of the doors, preventing the main door seals from being overwhelmed and leaking. Unique in design our seals fasten to the outer edge of the vehicles body where the doors close. Our seals are extremely easy to fit, just peel off the 3M sticky tape on the reverse and fit in the positions shown in our video and pictorial instructions. The seals close up the gap between the body and the door stopping water pooling on the main door seal, preventing leaks. Also included is a replacement boot seal, this is a direct replacement for the OEM part, this slots in to place as per the original, our seal is improved with a larger diameter to prevent leaks in to the boot.Alongside this we also supply an additional top seal which works in the same way as our door seals, providing an external seal, preventing pooling of water within the tailgate. Our seals are a direct fit and can be fitted in under 20 minutes. Our seals are cut to size ready to fit, we also include 2x alcohol wipes to clean the vehicles body prior to fitting our seals. Vehicles affected Citroen C1 MK1 2005-2014 Toyota Aygo MK1 2005-2014 Peugeot 107 MK1 2005-2014 Associated part numbers:B000651380, 62331-0H014, 8707C7, 9025A6, 9025AK, 9025A8, 9025AL. You will receiveX2 External door seals X1 Improved design tailgate seal X1 External tailgate sealX3 Alcohol wipes
BMW Mini Cooper S R53 R52 Eaton Supercharger Oil Service Kit Overhaul JCW Install Instructions Guide X8R Ltd 2020-06-10 | Symptoms of fault This is a preventative service kit to avoid future failure of the supercharger components. The fault Scheduled servicing of the supercharger is important to keep in the best condition and to prevent failure. The R53 and R52 Mini Cooper S models are fitted with an Eaton supercharger. The supercharger is lubricated and partially cooled by oil located in two reservoirs within the supercharger housing. BMW / Mini do not offer a change of this oil / service of this part as part of the service schedule. However other manufacturers vehicles utilising the same supercharger recommend servicing at 40,000 miles. It is not uncommon for the seals to weep on the supercharger allowing oil to escape. Most enthusiasts therefore recommend servicing every 40,000 miles to keep this oil fresh and topped up- preventing failure of the supercharger components. These superchargers are one of the most expensive components on the vehicle and used units can provide their own issues. The solution Service your vehicles supercharger using our comprehensive kit, prevent failure of the unit. Our comprehensive kit includes all the parts you will need to carry out a full service of the supercharger off of the vehicle. This is the very best way to ensure a full service and complete exchange of the oil. Our parts (developed by working on these vehicles), coupled with our thorough install pictorial and video instructions allow you to carry out this service, providing the ultimate reassurance.We recommend removing the supercharger from the vehicle to service, we believe this is the most thorough way, all our components included here allow you to do this replacing all consumables, gaskets and parts which will likely need replacing along the way. We recommend refilling the supercharger off of the vehicle through the drain plugs, we don’t advocate removing any of the casting of the supercharger as we feel this is more likely to introduce contaminates. Our comprehensive kit includes the following:210ml turbine oil. Made by Shell to MIL-PRF- 23699G and DEF-STAN91-101 standards. Matching and exceeding Eaton requirements. Enough to fully refill both reservoirs on the supercharger.Green supercharger to air tube gasket (Vitor Reinz) equivalent to 11610020836. Failure of the seal and subsequent air leaks are common and this leads to rough running and a lack of power. Viton O Rings (best material for environment fitted) to replace the often perished seals on the supercharger drain plugs.Bypass valve pipe, ASH branded (select if purchasing for auto or manual so we send correct pipe) Equivalent to 17511524538 or 17517541463. Supplied with x2 Stainless steel slim hose clamps to replace OEM hose clips which are not easy to reuse (11651521321). Note our hose clamps have a band thickness of 0.7mm. Where this isn’t considered it makes the hose very difficult to fit. Three slim stainless-steel hose clamps to replace OEM clips which are difficult to reuse on both ends of the airbox to throttle body valve intake hose. X1 to replace the clip on the main intake duct (to replace 13721491752) these hose clamps need to be slim line to fit the mounting recess correctly. Large supercharger inlet horn gasket (Elring) to replace 17511520044. Enabling removal of the supercharger inlet horn to clean / inspect the rotor. A pair of Viton O-rings (the best material for the fitting environment) equivalent to 11517509186 to replace O-rings on the water pump. To replace flange to block O-ring and water pump to flange O-ring. Viton O-ring seal to replace seal on the crank position sensor (equivalent to 12147514983) This is normally leaking on these vehicles and it is the best time access wise to replace this when removing the supercharger. 60ml syringe with long filler pipe to insert oil in to supercharger drain holes. 3/16 AF long arm Allen key (not found in most socket sets) to remove supercharger drain plugs, metric sizes will not fit and will cause damage. Dipstick crankcase bung plug, to prevent coolant entering the crank case when removing the water pump. Replacement throttle body gasket, essential to replace when removing the throttle body unit to service the supercharger. Equivalent to 13547509045.Bolts and washers included to screw in to the front frame to allow the radiator to be safely removed. Check out our instructions to see how crucial these are. Replacement dip stick tube O-ring, this should be replaced when removing the tube to access the supercharger. Equivalent to 11437513891. Vehicles affected BMW MINI Cooper S R53 2000- 2006 (Inc JCW models)BMW MINI Cooper S Convertible R52 2002-2008
DSG Mechatronic 7 Speed Gearbox Hydraulic Accumulator Repair Kit Leak Fix VW AUDI SKODA SEAT Install X8R Ltd 2020-02-11 | Symptoms Of FaultVW 06079 GENERIC P17BF. VAG 006079/10902/10903, P17BF, Hydraulic pump - play protection.VW 06300 GENERIC P189C. VAG 006300, P189C, Function restriction due to insufficient pressure build-up.P1895, Reduced function because of pressure drop.Loss of power (gone into neutral), no gears can be selected, hydraulic pump runs constantly, you can see hydraulic fluid bubbling/rising out of the breather, flashing spanner icon where gear number usually shows.The FaultThe accumulator mounting within the DSG unit fails causing these faultsWithin the DSG Mechatronic unit, the hydraulic pump pushes oil through the filter towards the pressure accumulator which provides the system with oil pressure when the pump is switched off. The cast metal part that the accumulator seats in to is too thin for the pressure exerted, this causes this part to crack and for the system to lose pressure causing the mechatronic unit to fail. To replace the cast metal part is a very time-consuming job and would only fail again in future.The SolutionOur unique design repair restores full function to the DSG unitOur unique repair kit allows you to repair the failed cast block. Our accumulator base mounts to the cast block restoring full function, our improved design accumulator simply then screws in place, providing a full-term repair for this common fault. For some types of transmission, the repair is possible in situ – provided the mechatronic sump can be removed in situ. Even if this isn’t possible and the unit has to be removed our repair is still far simpler than replacing the cast block which requires complete disassembly of the Mechatronic unit.No programming is required pre or post installation. After the repair, pressure is restored and normal operation resumes.Vehicles AffectedThe below is for guidance only, please check before buying that you have a DSG7 speed gearbox, any doubts let us know your VIN before purchase and we can look up to be sure.Compatible with following gearboxes: DSG 7 gearbox models0AM 325 025 M Z1L0AM 325 025 M Z2B0AM 325 025 M Z2N0AM 325 025 K Z6D0AM 325 025 K Z6C0AM 325 025 K Z6TAssociated part numbers:0AM 927 769 D0AM 927 769 K0AM 927 769 G0AM 325 025 D0AM 325 025 H0AM 325 065 N0AM 325 025 J0AM 325 065 L0AM 325 065 SDQ200 DSGPlease check your vehicle has a DSG 7 speed gearbox.Audi A1 2008-2011 1.4l 1.6l 7 SpeedAudi A1 (8X) with 7-speed dual clutch gearbox Model Years 2011-2016Audi A3 (8P, 8V) with 7-speed dual clutch gearbox Model Years 2008-2016Audi Q3 2011 1.4l 1.6l 1.8l 7 speedAudi TT (8J) with 7-speed dual clutch gearbox Model Years 2012-2016SEAT Altea / XL 2009-2011 1.6l 1.8l 7 speedSEAT Ibiza 2009-2011 1.2l 1.4l 1.6l 7 speedSEAT Leon 2007-2011 1.8l 7 speedSkoda Fabia 2010- 2011 2013-2015 7 speedSkoda Modela 2011 1.4l 1.6l 7 speedSkoda Octavia Model Years 2009-2015 7 speedSkoda Superb Model Years 2008-2015 7 speedSkoda Rapid Model Years 2014-2015 7 speedSkoda Roomster Model Years 2013-2014 7 speedSkoda Yeti Model Years 2013-2015 7 speedVolkswagen Beetle / convertible Model Years 2011-2015 7 speedVolkswagen Bora 2010-2011 1.4l 1.6l 7 speedVolkswagen Caddy Model Years 2010-2015 7 speedVolkswagen Golf / Golf Plus Model Years 2007-2015 7 speedVolkswagen Jetta / Jetta Wagon Model Years 2008-2015 7 speedVolkswagen Lavida 2010-2011 1.4l 1.6l 7 speedVolkswagen Passat Model Years 2008-2015 7 speedVolkswagen Polo Model Years 2007-2015 7 speedVolkswagen Sagitar 2009-2011 1.4l 7 speedVolkswagen Scirocco 2008-2011 1.4l 7 speedVolkswagen Sharan 2010-2011 1.4l 7 speedVolkswagen Tiguan 2011 1.8l 7 speedVolkwagen Touran 2010-2011 1.4l 1.6l 1.8l 7 speedAnd other models with a DSG 7 speed gearbox.You Will Receive1 x Replacement accumulator (complete with o ring)1 x Accumulator housing / cast block adapter (complete with o ring)1x Accumulator spanner.
Audi Seat Skoda VW 2.7 3.0 TDI Intake Manifold P2015 Error Motor Actuator Bracket Fix Install Guide X8R Ltd 2020-02-11 | Symptoms Of FaultError Code: P2015, “Intake Manifold Flap Position Sensor, Bank 1 - Implausible Signal”. Error Code: P2020, “Intake Manifold Flap Position Sensor, Bank 2 - Implausible Signal”. VAG Error Code: 18447, 7859, 008213. VAG Error Code: 18452, 008224. Malfunction Indicator Lamp (MIL)(K83) active. Check engine light illuminated/flashing. Rough idle. Decreased fuel economy. Reduced acceleration. Increased fuel consumption. Intake Manifold Flap Motor (V157) stuck/faulty.Possible other error codes: P2004, P2005, P2006, P2007, P2008, P2009, P2010, P2011, P2012, P2013, P2014, P2016, P2017, P2018, P2019, P2021, P2022, P2023, P3135, P1018.The FaultThe actuator motor on the intake manifold over rotates; triggering fault codes. When the Engine Control Module (ECM) detects that the intake manifold is not functioning properly it will normally illuminate the check engine light.The intake manifold control valve/position sensor (which is typically located at one end of the intake manifold) provides values which help the vehicle’s Powertrain Control Module (PCM) control the amount of air being allowed into fuel injected engines at various RPMs. Using information from the sensor, The Intake Manifold Runner Control (IMRC) determines the position of the throttle body plates (commonly called flapper valves) and adjusts them to adapt to engine load variations. This ensures a correct mixture of fuel and air by limiting the amount of air that can pass though the engine. The P2015 code means that there is out of range data from the senor. The P2020 code is the fault code associated with Bank 2 for the same issue.If your vehicle has a P2015 and/or P2020 error it is very likely the main dealer will look to fix this issue with one or two completely new intake manifolds at significant cost. The fault however usually lies with the actuator motor on the intake manifold(s). There are two plastic limiting stops on the large cog within the motor. These are delicate and inevitably wear, allowing the motor to over rotate which triggers the P2015/P2020 error.Our repair brackets can be installed very easily providing a solid limit for the actuator motors - curing these faults for the life of the vehicle. There is no need to replace the complete manifolds / actuator motors which would only fail again.The SolutionFit our brackets and remedy the over rotation with a hard limit for the actuator motor. Clearing fault codes. We recommend to fit both brackets at the same time as the two manifolds work together so it is preferable for them both to have the same limit.Our brackets can be fitted very simply, usually in under 15 minutes, with basic tools. They attach to the manifold actuator motors themselves and stop the over rotation which causes the fault. Many of our customers have purchased our brackets as a preventative measure before their motors fail.Our parts limit the motors to the same range as when they were new. Avoid the cost of a complete new manifold and actuator motor (or two) which would only fail again and which requires the removal of the fuel lines for installation.No software (VCDS/ VAG COM) is needed for this repair, check out our instructions and videos, after the bracket is fitted the error will clear on its own.Our bracket is unique in design and is constructed from stainless steel. Fit our bracket quickly and simply and cure this common fault.Vehicles AffectedVAG 2.7 & 3.0 v6 TDI engines with actuator motor with 4-pin and 5-pin plug. Both left-hand and right-hand manifolds, Type A & Type B. 2007 onwards.Compatible with actuator part numbers: 059129086J, 059129086L, 059129086G, 059129086K, 059129086D, 059129086M, 059129086E.Associated manifold part numbers: 059129711AF, 059129711AG, 059129711AL, 059129711AR, 059129711BJ, 059129711BK, 059129711BP, 059129711BQ, 059129711BR, 059129711BS, 059129711CA, 059129711CG, 059129711CH, 059129711CK, 059129711CL, 059129711DC, 059129711T, 059129712AJ, 059129712AR,059129712BA, 059129712BC, 059129712BE, 059129712BF, 059129712BG, 059129712BH, 059129712BK, 059129712BL, 059129712BM, 059129712BN, 059129712BQ, 059129712BR, 059129712BS, 059129712BT, 059129712CA, 059129712CB, 059129712CK, 059129712E, 059129712H, 059129712N, 59129712P, 059129712T.Associated vehicles: Audi Q7 3.0 TDI from 2007Audi Q5 3.0 TDI from 2009Audi A4 3.0 TDI from 2008Audi A4 2.7 TDI from 2008Audi A5 3.0 TDI from 2008Audi A5 2.7 TDI from 2008Audi A6 3.0 TDI from 2008Audi A6 2.7 TDI from 2008VW Touareg 3.0 TDI from 2007VW Phaeton 3.0 TDI from 2007Audi; A8 & Q7Associated engine codes: CAMA, CAMB, CANA, CANB, CANC, CAND, CAPA, CARA, CASA, CASB, CASC, CASD, CATA, CCLA, CCMA, CCWA, CCWB, CDYA, CDYB, CDYC, CEXA, CGKA, CGKB.Complete Kit2x Stainless steel brackets to fit both Left and Right hand manifolds. (4 and 5 pin)
For Nissan Qashqai Tailgate Boot Handle Repair Clip Kit Clips Snapped 2006 -2013 Instructions Guide X8R Ltd 2019-07-05 | Please be aware!Note: if paint on rear of handle remove this first with sandpaper to allow Acetone to melt the plastic. Note: make sure Acetone melts plastic before fitting the clips to the handle, IT IS NOT GLUE. The surface needs to start melting for the parts to fuse together. The ProblemIt is very common for the clips on the inside of the tailgate handle to snap. The small plastic clips moulded on the inside of the tailgate handle snap causing the handle to become loose, making it difficult to open the boot. This is a very common fault on these vehicles; these clips simply aren’t strong enough and will inevitably break. The solution until now was to purchase a complete handle, not only is a new handle expensive, it would also need to be colour coded and ultimately would have the same flawed design which would only fail again. Symptoms of the faultTailgate handle internal clips, snapped, damaged, broken. These snap or break off completely leaving the handle, loose or hanging.Vehicles affectedNissan Qashqai (2006 - 2013) Nissan Qashqai +2 (2008 - 2013) Nissan Dualis (Japan / Australia) Will fit all variants with / without reverse camera, with / without I-Key.Associated part numbers:90812JD00H, 90812JD20H, 90812JD01H, 90812JD30H. Our solution Install our replacement improved design clips and refit your boot handle securely. Install our replacement clips and reuse your existing handle, saving the cost / need to colour code a new handle which would only fail again. Our unique clips are very easily fitted, no need for measuring (with potential for mistakes like other kits). Our parts aline to the handle perfectly, no measuring at all just pop in place. No adjustments needed.Our clips are moulded from ABS plastic NOT 3D printed so quality is assured. Our clips are easily fused to the original handle using Acetone included in our kit. Providing a far superior fastening to any glue. Our clips are a complete redesign; thicker and stronger in every dimension and designed for life long use. Suited to the application and all temperatures. The original screws simply click in to our clips allowing easy fitting back to the vehicle with no specialist tools required. Check out our video and instructions to see how easy this repair is with our unique kit. You will receive1 x Left hand clip block 1 x Right hand clip block1 x Pure Acetone
Mercedes Benz OM642 V6 Diesel Intake Inlet Manifold Swirl Flap Repair Connecting Runner Rod Fix Kit X8R Ltd 2019-06-25 | FaultMercedes OM642 V6 vehicles suffer issues with the intake manifold, the swirl flaps within this manifold are controlled by an external operating rod. This is made of a poor-quality plastic which wears prematurely. Swirl flaps are designed to aid with low down torque and fuel economy. Over time the plastic wears at the connection points with the manifold, creating an oval shape which eventually lifts up the rod leading to breakages causing the faults noted above. A physical inspection of the intake manifold will quite often show that the rod has snapped in half. The wear is caused by the plastic being the wrong specification for this task, it cannot deal with the heat and constant mechanical motion involved.These intake manifolds can also get severely clogged up with carbon deposits which can lead to the swirl flaps becoming harder to move which in turn leads to more stress on the motor and rod.You can ordinarily identify this issue by removing the engine cover and inspecting the intake manifold, often the rod is snapped or you can test the excess play in the rod linkage. SolutionOur repair kit is the best solution to this fault. The manufacturer will advise to replace the entire intake manifold (£600+). The new manifold would come with the same plastic rod attached which will lead to the same problem further down the line.In the case of this engine, there are two intake manifolds, each with a rod, so to replace both will cost a small fortune, especially as its generally just the rod that needs replacing.Our kit comprises of an aluminium rod machined from billet aluminium and anodised. It will not snap like the plastic versions and is designed to cope with the sustained heat and movement experienced during operation.Our rod comes complete with anti-friction adaptors, these interact with the plastic bushes of the rod and the plastic of the manifold connections, this means there is plastic on plastic operation, our anti friction adaptors allow easy slip and protect from wear. Not a metal on plastic operation which would ultimately fail. A far superior improved design and material part. Our part features sensor pick-ups. Some manifolds have a position sensor on the plastic rod, failure to replicate this in a replacement rod will throw up errors. Our rod has this feature built in so can be a straight swap. Our rod will work with manifolds both with and without sensors.Vehicles affectedThis list is for guidance only, and may not be a complete list of vehicles with this engine. We have taken measures to ensure that all the below cars have compatible manifolds but you are best to check before purchasing. You can check here: nemigaparts.com/cat_spares/epc/mercedesFind your model, click Engine, click Intake and Exhaust Manifolds. You can then check the part number corresponds to the ones in this listing. You can also visually inspect the manifold by removing the engine covers to confirm compatibility.Please note our rod will replace rods both with and without sensor pick-ups. Will fit both. Our rod will also fit both intake manifolds on these vehicles Left and Right hand side. Mercedes Benz:C Class:W203 C320 CDI (2005–2006) W204 C320 CDI (2007-2009)W204 C350 CDI (2009–2014) W204 C350 CDI Blue Efficiency (2009-2011)E Class:W211: E280 CDI (2005-2009)W211: E300 BlueTec (2006-2009)W211: E320 BlueTec (2006-2009)W212: E300 CDI Blue Efficiency (2009-2016) W212: E350 CDI Blue Efficiency (2009-2016) W212: E350 Bluetec (2009–2016)W213: E350d (2016-2018) S Class:W221: S320 CDI (2006-2008)W221: S320 CDI Blue Efficiency (2008-2009)W221: S350 CDI Blue Efficiency (2009-2013)W222: S350 BlueTec (2013-2017)G Class (W463):G320 CDI (2006–2018)G280 CDI (2010-2018)G300 CDI (2010-2018)G350 BlueTEC (2010-2018)G350 CDI (2009-2018)GLK Class (X204):GLK 320 CDI (2008-2009) GLK 350 CDI (2009–2012) GLK 350 CDI Blue Efficiency (2012-)R Class (W251):R280 CDI (2007–2013)R300 CDI (2007–2013)R320 CDI (2007–2013)R320 Blue Tec (2007–2013)R350 CDI L (2007–2013)ML/GLE Class:W164: ML320/350 CDI/Bluetec (2009–2011) W166: GLE350 BlueTEC (2012-2019)GL Class (X164):GL350 CDI (2009) GL350 CDI (2010-2012) GL350CDI BlueTec (2009-2012)CLS Class:W219: CLS320 CDI (2005-2010) W219: CLS350 CDI (2007-2010) W218: CLS350 CDI BlueEfficiency (2011-2014)W218: CLS350 BlueTec (2014-2017)Vito/Viano (W639):Vito 122 CDI (2010-2014) Vito 122 CDI Blue Efficiency (2010-2014)Vito 3.0 CDI (2010-2014)Vito 3.0 CDI Blue Efficiency (2010-2014)Sprinter (2006–Present) (W906):218CDI, 318CDI, 418CDI, 518CDI (2006-2014) 219 CDI BlueTec, 319CDI BlueTec, 519CDI BlueTec (2014-)NOT COMPATIBLE WITH Sprinter Gen2 NCV3 OM642 3.0L V6 (2007-2009). Please check your intake manifold rod to make sure that it has a sensor pickup point at either end of the rod (facing opposite ways). If it has sensors back to back at one end of the rod, this option is not compatible with our kit.
BMW X3/X5/X6 Transfer Case Actuator Motor Repair X8R Ltd 2019-06-24 | SYMPTOMS OF FAULTBrake, ABS, and 4X4 lights all lit?Clicking / juddering sound from transfer case “4X4 inactive” message.THE FAULTThe gear within your transfer case actuator wears and causes the symptoms noted above.Attached to the transfer case is an actuator motor, within in this there is a poor quality Nylon plastic gear, this is turned by a metal worm gear. Over time the Nylon wears down and strips and leads to the gear not turning; this results in the symptoms noted above. BMW do not supply this part as a spare, they will provide at vast cost a complete replacement motor, this however will fail again because of the Nylon gear.THE SOLUTIONFit our improved design actuator gear and restore your actuator motor.Replace just the failing component the Nylon gear with our replacement gear made from a plastic / Carbon Fiber mixture; a far better quality part than OEM. This will repair the issue and save the cost of a new actuator motor that would just fail again. A high quality precision made improved material replacement part.VEHICLES AFFECTEDX3 E832.0d 2003- 20062.0i 2003-20062.5i 2003-20063.0d 2003-20063.0i 2003-2006X3 E83 LCI1.8d 2009-20102.0d 2006-20102.0i 2006-20102.5si 2006-20103.0d 2006-20103.0i 2006-20103.0sd 2006-20103.0si 2006-2010X5 E533.0d 2003-20063.0i 2003 (Oct onwards) -20064.4i 2003-20064.8is 2003 (Nov onwards) -2006BMW X5 E703.0d 2006-20103.0sd 2007-20103.0si 2006-20103.5d 2008-20104.8i 2006-2010X5 M 2008-2013BMW X5 E70 LCI35dX 2009-2013BMW X6 E7130dX 2007-201035dX 2005-201035iX 2007-201040dX some modelsX6 M 2008-2014X6 Hybrid 2009-2011Associated part numbers:2710756629627107568267ATC 400 ATC 500 ATC 70027107566296GR, 7-10-7-566-296GR, 27 10 7 566 296GR, 27107566296GR, 27-10-7-566-296, 27 10 7 566 296 , 27107566296, BOSCH 013000850, 8473227771, 8472227771, 09-3509-010, 9 3509 010, 093509010, 2710 7528559-01.YOU WILL RECEIVE1X Carbon fibre reinforced plastic gear
Mercedes Benz W639 Vito Viano Gear Selector Shift Stick Lever Bush Repair Fix Kit Manual Guide X8R Ltd 2019-06-24 | SymptomsSloppy gear changes, loose feeling gear shift, difficulty getting into gears especially reverse and first. Gears feel like they have shifted over to the left so that 3 & 4 are where 1 & 2 normally sit. Wobbly / loose gear stick.FaultA bush within the gear stick assembly wears causing shifting issues. Within the OEM gear stick shift mechanism is a poor-quality Nylon bush, a ball at the bottom of the shift stick operates within this bush, this is tight friction fit, the Nylon being of poor-quality wears away, allowing excess movement, causing the faults noted above. The solution until now was to replace the whole gear shift unit, not only is this expensive but it would inevitably fail again. SolutionInstall our new improved design bush and restore sharp gear changes. Fit our improved material and design gear stick bush. Replace the poor-quality OEM bush with our new part at a fraction of the cost of changing the complete gear stick assembly (£300+). This will bring the sharpness back to your gearbox and make driving the vehicle easier and more enjoyable. Our bush is made from a high-quality modified nylon and will not fail like the OEM part. Our part is made in two halves to make installation very easy, please check out our instructions and video. Our part is injection moulded for the perfect finish. This is essential in providing smooth operation and combating wear. Not 3d printed or machined. Constructed of the best material for this application, this is what we specialise in, please check out our feedback. Vehicles affectedMercedes Benz Vito/Viano W639 (2003-2014) 5 and 6 speed manual gearboxes only.Mercedes Benz V-Class V350 (Japan only)Mercedes Benz Valente (Australia only) 2012-2014Associated part numbersA6392605309, A6392603500, A6392607109, A6392605509, A6395450532, A6392602998, A6392601109, A6392602509, A6392607309.You will receive1x Improved material / design gear stick bush (in two halves for easy install)
Mercedes SL S CL Class R230, W220, C215 PSE Central Locking Vacuum Pump Motor Impeller Repair Kit X8R Ltd 2019-06-24 | SymptomsCentral locking not unlocking doors, boot not popping open, lumber supports in seats not operating, soft close boot not working.Key fob won't lock or unlock any door, including rear hatch. (Key fob is perfectly operational otherwise)Pressing door lock/unlock buttons inside the car fails to lock or unlock any door.You can hear vacuum pump motor working but nothing is happening, motor runs for too long then cuts out. Vacuum pump makes clicking sound when you press lock/unlock on key fob. FaultA graphite impeller within the vacuum pump fails causing vehicle faults. Sometimes water ingress can cause problems with these pumps, often however the impeller on the spindle of the motor can break or shatter over time. A broken impeller will cause a lack of air pressure / vacuum to be provided meaning actions of the PSE pump will be inhibited. It can also lead to a jammed motor which will lead to the pump blowing the 20A fuse and shutting off.Common associated fault codes:B1436-012, B1436-014, B1436-015, B1436-016, B1436-017, B1437, B1438-011, B1438-012, B1440, B1442-012, B1442-015, B1442-016, B1442-017, B1442-018.SolutionInstall our replacement impeller and restore your vacuum pumpDealers will try to sell you a complete new PSE pump at great expense (£900+), but our solution simply replaces the component part that has failed; the motor impeller. This repair with our replacement graphite impeller wheel and new fins will get your pump back to full working order at a fraction of the cost. Our parts are made of an improved Graphite material. Replace just the component that fails, avoid the cost of a whole new PSE pump assembly that would just fail again. Install of our new component is straight forward please check out our instructions and video. Vehicles affectedMercedes Benz SL-Class (R230) 2001-20111st gen: 2001- 2006 – SL350, SL500, SL600, SL55AMG, SL65AMGFacelift 1: 2006 - 2008 – SL350, SL500, SL550, SL600, SL55AMG, SL65AMGFacelift 2: 2008 - 2012 - SL280, SL300, SL350, SL500, SL550, SL600, SL63AMG, SL65AMGMercedes Benz S-Class (W220) 1998-2005S280, S320CDI, S320CDI L, S350, S350 L, S400CDI, S430, S430 L, S500, S500L, S500 4-Matic, S600L, S55 AMG, S55 AMG LMercedes Benz CL-Class (C215) 1999-2006CL500, CL600, CL55AMG, CL63AMG, CL65AMGThis information is for guidance only, to be sure visit real OEM, click Mercedes catalogue, select your vehicle model, then select your variant, click Vacuum System / Hydraulic System, click Vacuum pump, this will show the part number for your vacuum pump. You can then compare to the part numbers below to confirm compatibility. Alternatively, you can visually inspect the unit for the part number. Associated part numbersBosch motor part number: 1397220291Mercedes pump part numbers: A2308000648, A2308000548, A2308000448, A220800348, A2208000648, A2208000748, A2208000548, A2208000848, A2208001148, A2208001248, A2208000948.You will receive1 x Graphite impeller wheel8 x Graphite replacement fins
