Diffraction LimitedThis video shows 2D wave simulations of optical fibers and presents differences between single-mode and multi-mode light propagation.
Fiber Optics - Simulating Light in Optical FibersDiffraction Limited2023-11-05 | This video shows 2D wave simulations of optical fibers and presents differences between single-mode and multi-mode light propagation.
0:00 Simulation Program 1:37 Fiber Simulation 1 - Varying Diameter 3:04 Fiber Simulation 2 - Varying Wavelength 4:08 Fiber Simulation 3 - Moving Source 4:31 EndscreenRuling Machine Part 4 - DIY Diffraction Gratings [4k]Diffraction Limited2024-10-12 | Showing the assembly and first tests of the ruling machine. Accuracy of line spacing is still an issue and the Y-axis needs to be improved in future.A build guide for DIY Air-Bearing Pads [4K]Diffraction Limited2024-09-28 | Finally I had time to finish this video about small and easy to build air bearing pads. The video contains a complete guide to build your own pads.
The CAD models are now available on my Github: github.com/0x23/open-air-bearings You will find ready to print .obj files for 1 inch pads there too (steel_epoxy_pads).
Chapters: 00:00 - Intro 00:40 - How air bearings work 02:43 - Tools & materials 06:41 - Design considerations 07:42 - Bearing surface molding 17:31 - Channel scoring 23:18 - Restrictor nozzle 28:21 - DemonstrationBuilding a Small and Quiet Air Compressor [4K]Diffraction Limited2024-03-11 | In this video the design and build process of a small air compressor unit is shown. It can reach about 10 bar or 150 psi. 3D-Printed parts are used were possible to make manufactioring easy.
Many air compressors rely on momentum to push through the hardest point of the compression cycle and therefore can not operate at low rpm and lack the torque to start when pressurized. The presented design uses a 4:1 reduction and a BLDC Motor to overcome this limitation.
The CAD files will be available soon on my github page: github.com/0x23/QuietAirCompressorExamining the NUBB23 Laser Diode Array [4K]Diffraction Limited2024-02-18 | In this video, a close-up examination of the NUBB23 laser diode array is conducted. The collimation lens is removed to expose the diode assembly, and the beam profile is demonstrated both with and without the collimation lens.Wave Simulation of a Photonic-IC for Neural Network AccellerationDiffraction Limited2024-01-07 | In this video a simple model of a photonic IC is simulated. Similar devices are subject of current research and are explored for accelerating neural network computations with low energy. The company 'Lightmatter' already offers products based on the technology.
The optics simulation program is open source and can be found on my github page: github.com/0x23/WaveSimulator2DA Cable Robot 3D-PrinterDiffraction Limited2024-01-04 | The video presents a cable driven 3D-Printer, based on the parallel kinematic delta plattform. The machine uses dyneema fishing line as cables and a custom kinematic model running on the 'smoothieboard' printer board.
Carbon fiber preloading rods are used to keep the cables under tension, providing the necessary stiffness and allowing for rapid accelartion. The parallel kinematic design has potential benefits for large workspaces.Crude concept for DIY resist from PCB-Film.Diffraction Limited2023-12-01 | This video shows a crude demonstration on how one could optain a liquid photoresist from easily available materials. Although liquid PCB resists like "Positive 20" exist. They are not easy to get in certain regions.
I would be very interested in making this process work, so if any viewers have ideas on how to improve upon this, please leave a comment.
Also check out the great videos of 'ProjectsInFlight' on DIY chip making and photolithography processes: youtube.com/@projectsinflight30 Nanoseconds after you switch on the Light [4K]Diffraction Limited2023-11-27 | Having a little fun with the wave simulation, recreating incoherent light with a wide frequency spectrum. In contrast to the ordered oscillations of laser light, I always found it hard to imagine how 'normal' everyday light would look like on the wave level. The video was made to answer this question.
Music: Ambient Wave 48 (Tribute)Fiber Optics - Multimode vs Singlemode FiberDiffraction Limited2023-11-02 | Light is coupled into different optical fibers and the difference between multimode and singlemode fibers is demonstrated. The focus of the video lies on practical demonstrations and not on theory, as there are already many good resources on the subject.
0:00 Introduction 0:15 Fiber modes 0:48 Setup 1:24 Singlemode vs Multimode 3:15 Swapping fiber 4:00 Fiber alignment 5:04 9µm Fiber 5:40 EndscreenFiber Optics - Extracting Ceramic Ferrules from Optical Network CablesDiffraction Limited2023-10-31 | This video show how ceramic ferrules can be extracted from fiber optic cables. Ceramic ferrules are made of a hard ceramic material and have a very small precision bore of 125 microns in the center.Free Optics Simulation in Blender - TutorialDiffraction Limited2023-10-19 | This video shows how to setup Blender and the LuxCore renderer to perform 3D optical simulations (ray optics). Both programs are free and open source ! With these tools you can simulate any combination of: * Lenses * Mirrors * Prisms * Laser beams * Freeform optics * Screens
The physically based LuxCore renderer supports efficient pathtracing (Bidirection Metropolis Light Transport) to handle indirect lighting, scattering, relfections and refractions with caustics. For optics simulations, it is far superior to blenders build in raytracer 'Cycles'.
0:00 Introduction 0:29 Installing LuxCore 1:43 Setting up demo scene 3:16 Render settings 4:20 Adding a lens 5:00 Setting up materials (glass / diffuse) 5:54 First simulation results 6:15 Fog for beam visibility 8:15 Creating a mirror 8:53 Playing around with complex scene 10:18 Rendering the resultLaser Diode Back ReflectionDiffraction Limited2023-10-09 | Small demonstration of how back relfected light can destroy coherence of a laser diode.
A collimated laser beam is used in a simple 'glass plate fizeau type interferometer' to create a stripe pattern. Adjusting the angle of the incident light beam to be exactly perpendicular to the glass plates surface creates a reflection that is focused back into the laser diode chip by the collimating lens.
This decreases coherence length quite dramatically so that the strip pattern vanishes.Ruling Machine Part 3 - Air Bearing SimulationDiffraction Limited2023-08-20 | This video demeonstrates how to design and evaluate planar air bearing pads using a python simulation program.
The code can be found on github: github.com/0x23/open-air-bearingsRuling Machine Part 2 - Base and X-Axis (DIY Air Bearings)Diffraction Limited2023-07-06 | Bulding the machine base from glass plates, adding the magnet preload bar and assembling the X-Axis.Ruling Machine Part 1 - Testing the air bearing stageDiffraction Limited2023-06-25 | Testing the prototype of the magnetically preloaded air bearing stage for the grating ruling machine. The next part (Part 2) will show more details of the building process. Information about building and designing custom planar air bearing pads from glass will be released in a seperate future video.