Dan LecocqWhen my scrap wood bin gets too full, I dump it out and see what I can make.
This time, I used some pen blanks (with brass tubes already glued in) and some other scraps to make some pendants, a spinning top and an ornament. I also made a couple of other blanks that I haven't figured out what I'll do with yet.
Scrap Wood ProjectsDan Lecocq2014-11-28 | When my scrap wood bin gets too full, I dump it out and see what I can make.
This time, I used some pen blanks (with brass tubes already glued in) and some other scraps to make some pendants, a spinning top and an ornament. I also made a couple of other blanks that I haven't figured out what I'll do with yet.Wooden Hand PlaneDan Lecocq2015-09-16 | A while back I made my daughter a wooden hand plane. She loves it, which made me want one for myself.
I wanted this plane to be something that I'd use often, something that would become a treasured tool in my shop. I had some free curly maple scraps that I'd been holding on to for over a year, waiting for a project just like this one.Large Chisel HandleDan Lecocq2015-08-26 | I found this large 2" chisel head at a tool swap, and finally got around to making a handle for it. The handle itself is made from tigerwood and a copper ferrule (though, I suppose it should really be 'cuprule', perhaps).Flush Trim HandplaneDan Lecocq2015-08-19 | I often seem to find myself needing to plane a surface even with an adjacent surface. When trimming splines, or edge banding, etc.
I saw this in a woodworking magazine about a year ago. If you know what magazine and issue, please let me know and I'll attribute it here.Celtic Knot PenDan Lecocq2015-08-12 | I needed to make gifts for a couple of friends, and I'd recently seen The Wood Knight make a celtic knot pen (youtube.com/watch?v=ifLP5SJDEoc) so I thought I'd give it a shot.
The inserts are made from layered veneers to give a bit more visual interest. One set of inserts has the light wood on the outside (to be inserted into the dark wood) and the other set has the dark wood on the outside (to be inserted into the light wood).Reclaimed Wood Segmented RattleDan Lecocq2015-08-05 | A coworker recently had a little baby girl, and so I thought I'd make a rattle for her. Because it has to be hollowed out I knew I would at least be gluing up two halves, so I figured I'd go all-out and make the head of the rattle completely segmented. It's made of walnut and reclaimed oak floorboards.
Alan Stratton on turning a sphere: youtube.com/watch?v=n6xG-i5e4PkFlap Sander FailDan Lecocq2015-07-29 | I tried out an idea I had for a flap sander where replaceable pieces of sandpaper are held in place with a pin. While the mechanism worked well, the sandpaper I used was not stiff enough. I'll see how it works at some point with thicker paper.Making a Rustic Necklace RackDan Lecocq2015-07-15 | I wanted to make a necklace rack for my sister, and I thought I would give it a shot using as few power tools as possible. I had some firewood that seemed perfect for the project (after making sure to get rid of all the creepy-crawlies).
Music: "Succotash" by Silent Partner via the YouTube Audio LibraryMaking a Magic WandDan Lecocq2015-07-08 | A while back I was with my daughter at woodcraft when an employee decided she needed a 3' piece of scrap maple to play with as a magic wand. So in this video I turn it into a real magic wand for her to play with.Making a Segmented Frame for a MirrorDan Lecocq2015-07-02 | Making a segmented frame for a mirror to match a turned clock I'd previously made. The segments are made out of tigerwood with padauk dowels for decoration.
The original turned clock: youtube.com/watch?v=kSSqF_iTCqo Making a segmenting sled: youtube.com/watch?v=7tWw9TV_ju4Making a Segmenting SledDan Lecocq2015-06-24 | Making a table saw sled for making segmented rings for woodturning, based heavily off of Stephen Ogle's design. I've got an upcoming project the requires some segmenting and I've been meaning to do this for some time now.
youtube.com/user/stvnogle youtube.com/watch?v=KCFgyYYjJegMaking Threaded KnobsDan Lecocq2015-06-17 | I never seem to have enough threaded knobs for shop fixtures and jigs, so I figured I'd show one way to make them. I like this method because they're perfectly centered and balanced. They're also a great way to use up some scraps.
While this can be used to make loose knobs, it's best to epoxy in the threaded rod with this style.
Check in next week for the project where I put these to good use!Making a Center FinderDan Lecocq2015-06-10 | Just a quick video this week -- after ages of measuring corner to corner to find the center of a workpiece, I finally took a few minutes to make a center-finder. Nothing too fancy or novel, but very useful.Making a Scrap Wood Garden ToolboxDan Lecocq2015-06-03 | I had some boards from a failed project that seemed like a good fit for a rustic project like this. We're not big gardeners, but we do have some garden tools we use pretty regularly and I wanted a toolbox to carry them.Making Bottle Stopper HoldersDan Lecocq2015-05-27 | Bottle stoppers have a convenient way to hold them while finish dries -- with a bolt or threaded rod. Here I make some holders so that I can more easily hold turned bottle stoppers to apply finish, and let them dry.Making a Candle HolderDan Lecocq2015-05-20 | After my daughter expressed some interest in making candles, we made a few only to realize that we had nothing to put them in! So in this video I turn a couple of candle holders on the lathe.Making a Bookbinding AwlDan Lecocq2015-05-13 | Making an awl for bookbinding (or woodworking) out of an old screwdriver and a small piece of pear wood.Making a Camera ArmDan Lecocq2015-05-07 | Making an articulating camera arm from pallet wood and plywood scraps. When shooting video for woodturning projects, the tripod always seems to be in the way -- this reaches over the bed of the lathe for a good view without restricting my access to the workpiece.Making a Framed SilhouetteDan Lecocq2015-04-29 | Happy Mother's Day to all mothers out there.
Here I'm making a trio of frame silhouettes for Mother's Day for my wife, mother, and mother-in-law. For those wary of making the silhouette, you can buy custom silhouettes from folks on Etsy.Making a Lamp FinialDan Lecocq2015-04-22 | My wife has a lamp that's very special to her, but all that's left of the finial is the threaded insert. I'll make a quick and simple replacement out of a small bit of scrap wood so that it looks more complete.Saw RestorationDan Lecocq2015-04-15 | Seattle Community College's Wood Technology Center had a tool sale a few weeks ago and I bought and old Disston saw. The blade seemed in reasonable condition, but needed a new handle and some cleanup. Six dollars well-spent.Fountain PenDan Lecocq2015-04-08 | Making a fountain pen for a friend. When I turn pens, I prefer simple, straight barrels, but obviously you could embellish a pen with curves or beads.Hortons Spotted EggDan Lecocq2015-04-01 | My daughter loves "Horton Hatches the Egg" by Dr. Suess, so I thought I'd make her a red and white spotted egg, just like Horton's.Making Wooden Toy ToolsDan Lecocq2015-03-25 | I made a set of woodworking tools for my daughter, including a hand plane, saw, mallet, square and screwdriver. The hand plane is covered in a previous video, but this documents the making of the rest of these toy tools.
Making the hand plane: youtube.com/watch?v=P7QcvXiLMgkMaking a Wooden Hand PlaneDan Lecocq2015-03-18 | My daughter's birthday is coming up and I made her some tools, including this wooden hand plane. While it's got a wooden 'blade' in it now, it does work with an iron.
I didn't follow along exactly, but I used this as a guide: http://www.crfinefurniture.com/1pages/sitelinks/howplane.htmlDrawknife RestorationDan Lecocq2015-03-11 | I got a rusted out old drawknife at Seattle Community College Wood Technology Center's annual tool swap. I thought I'd try out a technique I'd seen other use to remove rust, using vinegar. A couple handles, a HUGE amount of sanding and filing, and now I've a usable drawknife.Saw SharpeningDan Lecocq2015-02-25 | First attempt at sharpening my saw, after watching Paul Seller's series on the subject.
Paul Seller's video: youtube.com/watch?v=UA5DixEaaUoPallet Wood Plant HoldersDan Lecocq2015-02-17 | Making plant holders out of pallet wood.Blanket ChestDan Lecocq2015-02-11 | Making a blanket chest out of 2x4's and plywood.
It's meant to house a foam mattress for a futon, as well as double as a headboard for guests.Heart Pendants and EarringsDan Lecocq2015-02-05 | Making some heart pendants and earrings for Valentine's Day using some walnut and epoxy.Magnetic Knife HolderDan Lecocq2015-01-27 | Making a magnetic knife holder to replace our large cluttery one. Counter space is precious.Jewelry BoxesDan Lecocq2014-12-25 | Making a set of six jewelry boxes as gifts.
All the wood is either reclaimed, offcuts, scraps or from garage sales. The veneers come from a huge box I got at a garage sale. The sides and lid frame were made from scrap hardwood I got for free off of Craigslist. The inset lip is made from floorboards from the original Ballard post office, also found on Craigslist.Pepper MillsDan Lecocq2014-12-25 | Making a pair of pepper mills for gifts. These were my first pepper mills, but it went alright. Per Brendan Stemp's recommendation (youtube.com/watch?v=XdPQ7sfZeeU), I got CrushGrind mechanisms.
Rather than using the clips and the "CrushGrind tool," I removed the clips and epoxied the mechanism in place instead.Bottle Stoppers from Scrap WoodDan Lecocq2014-12-25 | Bottle stoppers for gifts. Made from various scraps glued up into blanks.Ring HoldersDan Lecocq2014-12-25 | Making some ring holders as gifts. The project was based off of a WWGOA article (http://www.wwgoa.com/a-beautiful-ring-box), though I decided to add magnets to help register the closed position.
In hindsight, the magnets added a whole lot of complexity without really improving the functionality, so I would recommend either using stronger magnets (I used 1/4"-diameter, 1/16"-thick rare earth magnets) or just not using magnets at all.Owl ClockDan Lecocq2014-12-25 | A bookmatched board bears an uncanny resemblance to an owl and is turned into a clock.LongboardDan Lecocq2014-12-25 | Making a longboard for Martín for Christmas. Inspired by Bob of "I Like to Make Stuff" (youtube.com/watch?v=UNwkDkowKpg).
I don't skateboard, so I can't speak to how well this works out, but I hope Martín gets some mileage out of it.A Turned ClockDan Lecocq2014-12-25 | Turning a clock as a gift. It's made of two layers of some anonymous hardwoods from the scrap bin, with the indicators out of padauk.Cheese Cutting BoardsDan Lecocq2014-12-06 | I make a few cheese-cutting boards for Christmas presents. I purchased the hardware from http://www.cheeseslicing.com/site/681068/page/924433, where they sell 'replacement handle arm assemblies' that contain the arm and the cutting wire.Scroll Saw Music BoxDan Lecocq2014-12-02 | A music box I promised my wife last year. The sides are scroll-sawn and filled with epoxy (for strength and to not collect dust in every crevice). The padauk legs provide strength to the otherwise-weak miter joints.
Check out his channel and you'll see someone who actually knows how to use a scroll saw: youtube.com/user/sdgood/videosCharging StationDan Lecocq2014-11-24 | I make a wall-mounted charging station to clear some clutter off of the counter. This is made entirely out of 1/10th of a sheet of 1/2" plywood.Flashlight HolderDan Lecocq2014-11-21 | My dad recently asked me to make something to hold his flashlight for him while he's repairing furnaces or doing ductwork. I came up with a few designs that I could make myself, but ultimately decided that the flexibility of a GorillaPod would be more useful.
I had planned on doing it myself, but it turns out they make a line that have magnetic feet. That meant that all that was left for me to do was to make a camera mount that can hold the flashlight. The flashlight in the video is not the same model as the intended, but the diameters are the same.Grandmas FramesDan Lecocq2014-11-19 | The making of some frames that Grandma Anna asked for.Pantorouter BenchDan Lecocq2014-11-19 | I make a bench using my recently-completed pantorouter. Made of (6) 2x4's and a quarter sheet of plywood.