synthpro
Synthpros Polymoog (video# 1)
updated
This is a video going over a Prophet 5 patch I have programmed into the memorymoog. This is a example of preset 3-6: Release-Repeat found in the Prophet 5.
NOTE: you may have to tweak the modulation amount and speed to get the results you are after, this can vary on Memorymoogs just a bit.
Thanks for watching!
Sincerely,
Jareth
this sound was used by many artists including Gary Numan on the albums, "Dance" and "I Assassin"
George Clinton also used this sound on Atomic Dog extended version.
Here is a link to my instagram for those interested, I have posted lots of Memorymoogs over the years as well as other fun projects etc: instagram.com/synthpro/?hl=en
Thanks for watching!
Sincerely,
Jareth
This is a look at a moog source I have brought back from the grave for Bobby. I give you a look at the pre restoration along with the final results.
Membrane panels can be ordered at www.Synhouse.com for those interested.
Note: I did recalibrate the filter a bit after this video was made, I wasn't happy with tracking. sometimes calibration shifts when chassis is closed due to changes in temperature of circuits.
Thanks for watching!
Sincerely,
Jareth
This is a video I made going over Phil's Minimoog after all the restoration work. I also go over the feedback loop you can do on these using the ext input.
Thanks for watching!
Sincerely,
Jareth
This is a video going over a minimoog I restored for Larry. I explain some of the interesting design changes for this early 1974 era minimoog.
Here is a link to the minimoog history video I made going over all design changes of the minimoog: youtu.be/-CvP4ap_kmg
Audio is from mixer straight into Canon XA11 XLR inputs for direct stereo audio recording.
Thank you Larry for giving me the opprotunity to restore your minimoog and to all of you who watch my videos.
Sincerely,
Jareth
Testing out my new camera this morning to see how it works. Also, thought some of you might enjoy a audio demo of the Behringer system 55. No Talking during the audio demo.
The audio is routed from my mixer straight into the XLR inputs on the camera so the audio is all integrated into the video from the XA11.
Thanks for watching!
Sincerely,
Jareth
I have wanted a modular moog for years and during the restore of the recent moog 1C modular, it pushed me into shopping around. Once I saw prices, I gave up but then discovered the Behringer System 55 and just had to buy one.
I made a quick and rough little demo as well as reviewed the build quality to possibly help some of you decide if this is the route you would like to go. the moog modular is panned slightly to left while the system 55 is panned to the right.
(Note: after reviewing the video, I realized I didn't quite set a 50% duty cycle square on system 55 at the end, that is the only drawback to small knobs...they are more sensitive than the larger ratio knobs found on moog).
apologies for the slight audio delay as well.
We made it to a part 4 of the Moog 1C. Today, I demo of the 956 ribbon controller that goes with Andrews modular. I finished it up this morning and wanted to share it as well. I didn't mention this in the video but the ribbon controller also has CV memory so when ribbon is released, it will hold the CV levels it was at, (just like a keyboard circuit).
Thanks for watching and as always I appreciate the support.
Sincerely,
Jareth
This is a video going over the competed Moog 1C that I have been working on for a couple of months now and am happy with how it turned out.
Here is a link to Andrew's YouTube channel, I encourage you to go check it out: youtube.com/@electro-classicorchestra1585
Thanks for watching!
Sincerely,
Jareth
This is a look at a very rare synth called the Sanctuary. This is bascially a rebadged Memorymoog Plus that was to be advertised/sold to churches here in the South, it was a push to help get synthesizers used in worship. This may not seem that big of a deal today with all the electronic worship music out there but this was a HUGE step back in this era.
Here is a link to Brad Hollands Company for those interested in learning more about ISLA Instruments: islainstruments.com
Thanks for watching!
Sincerely,
Jareth
This is a video going over a Minimoog I restored.
This unit got a new wood cabinet, interface overlay, badges, etc along with electronic repairs, preventive servicing, keyboard rebuild, 12 hour burn in, and final calibration.
Here is a link to the where this interface panel can be purchased:
ebay.com/usr/electronics_bizz?_trksid=p2047675.m3561.l2559
Thanks for watching!
Sincerely,
Jareth
Today I continue the adventure of bringing this Moog 1C back into great health. In this video, I give you a look at the guts of the modular and cabinet as well as go over serial numbers and build dates for the modules.
Thanks for watching and the support.
Sincerely,
Jareth
Going to be bringing you along on the adventure of getting this Vintage moog modular back to 100% operation. This unit was built around August of 1972 based on dates found inside.
Special thanks to Andrew for giving me the opportunity to work on his modular. And a BIG thanks to all of you who watch my channel, really appreciate it!
Sincerely,
Jareth
This is a special polymoog 203a restoration I had the honor of performing for the Wesleyan University's World Instrument Collection.
This polymoog belonged to Richard Teitelbaum who was a electronic avant-garde jazz keyboardist/composer and worked with many musicians over the years. Sadly, he passed in 2020 but his legacy lives on.
Special thanks to the Wesleyan University for the opportunity to restore Richard's Polymoog, this was truly an honor.
Here is a link to one of Richard Teitelbaum's tracks featuring the Polymoog and moog modular:
youtube.com/watch?v=d5LNiuSMoM0
Here is a little more info about Richard Teitelbaum posted by the Bob Moog Foundation:
moogfoundation.org/early-live-moog-modular-artists-richard-teitelbaum-first-moog-modular-synthesizer-europe
Thanks for watching!
Sincerely,
Jareth
This is a video I made in response to a request and hope it helps some of you out with your 280Z/ZX
Go to 7:27 of video for vacuum line connection
For those interested, here is a link to the electronic ignition video explaining its operation/location of components as well: youtube.com/watch?v=C8Jb9viNjmg&t=45s
Thanks for watching!
Jareth
I am always inspired by the polymoog but decided to step out of my comfort zone a bit with this one with vocals.
Thanks for watching!
Sincerely,
Jareth
Just some updates on my 280Z 2+2
I have been working on this car on and off for the last couple of months but just recently turned my attention to the rear hatch area. I have had to keep a tarp over her and it was time to finally get that leak fixed and attempt body work. This is my first attempt at bodywork so be easy on me.
I also went through all guages getthing them properly working and installed LED backlights.
She's a work in progress but every little thing helps.
I also took this car to a local car show a few weeks ago and had a great time meeting lots of people, (that 56 Chevy beside me was absolutely amazing btw).
Music:
This is a rough track I recorded a few weeks ago using Memorymoog and minimoog model D
Thanks for watching and hope these videos inspire you Zcar/ classic car owners out there.
This is a video going over the most recent restore project for Dave.
This is a early 1975 (Made Jan 14th, 1975) Minimoog that now has a new life.
Note: having some audio compression issues with this video. Oscillators are actully very warm and not distorted as it appears on this video
Thanks for watching!
Sincerely,
Jareth
Thanks for watching!
Sincerely,
Jareth
This is a video I made for Mike of his Memorymoog I have been restoring. This unit came in with a tuning stability issue as well as problems that would be later diagnosed as board contamination issues, (This is where the circuit board material becomes conductive causing cross talk between tracings etc) and addressed all of those problems as well.
This Memorymoog also got my individual voice output modifications and sounds great.
Thanks for watching!
Sincerely,
Jareth
This is a video I have put togather walking through the installation process of Synthtaste's Memorymoog supply upgrade. I cover everthing from power supply mounting to circuit modifications required as part of this supply upgrade.
If any of you are interested in this supply, they are available at www.synthtaste.com
(Note: I was informed by Martin that his website is currently down but will be back up soon)
Contact Martin here:
mghoewner@web.de
Speacial thanks to Martin at Synthtaste for the opportunity to work with your product!
Thanks for watching and hope this helps some of you out with installation.
Sincerely,
Jareth
It is with great excitement I present to you a moog Liberation I have been restoring for the Bob Moog Foundation.
I mention how heavy these are but they are really only about 15lbs.
Special thanks to the Bob Moog Foundation for the opportunity to restore this Liberation for you, it was truly a honor!
Thanks to all of you who watch my videos as well, wouldn't be following my passion if it were not for your support.
Sincerely,
Jareth
This is a video I made for Eric going over his micromoog I restored.
The audio interface for direct recording is a bit noisy at times with processing interference but will continue to work on my setup.
Thanks for watching!
Sincerely,
Jareth
This is a new track I have been working on tonight 4/18/22.
I was thinking back of my early days when I had just started playing synths and was sharing my recordings under Moog Paradise on Myspace...those were some fun times.
Instruments used:
1972 minimoog (Serial # 1548)
Memorymoog
Korg Koassilator (For piano loop)
Recorded to Cubase 11 through Steinberg UR816C interface
Thanks for listening and hope you enjoy!
Sincerely,
Jareth
This is a video I made going over a micromoog for Don.
Thansk for watching, greatly appreciate the support.
Sincerely,
Jareth
this is a video going over a Memorymoog standard I restored for Eric. This unit had lots of issues but not anymore.
The music starting at 36:19 is a original track recorded using my personal Memorymoog along with a Korg Kaossilator for drums.
Thanks for watching!
Sincerely,
Jareth
Wanted to take some time and answer the question that I get asked many times: What makes the Memorymoog have that sound and presence it does? This is a loaded question with many factors but I go over a few of the reasons as well as some of the stuff that can be found in other 80s synths.
This is Eric's memorymoog which there will be a video on once complete. I have literally just started on this unit and started with voices first...working my way backwards in this unit.
Appreciate you watching and all the support!
Sincerely,
Jareth
This is a video I made going over a Memorymoog plus I restored for Bob.
It was a very sick unit on arrival but now lives a healthy life.
Thanks for watching and appreciate it!
Sincerely,
Jareth
This is a video going over a Memorymoog Plus that I restored for Val.
Appreciate all you watching and thank you Val for giving me the opprotunity to bring your Memorymoog back alive.
Sincerely,
Jareth
This is a video going over a Korg Mono/Poly I repaired for Benjamin.
I also go over some of the calibraton to hopefully help some of you out that may own one of these.
Thanks for watching!
Sincerely,
Jareth
This is a video going over the Akai AX-60 I have repaired/serviced for Ben.
I show the features as well as walk you thorugh the control interface as well as some presets.
Thanks for watching.
Sincerely,
Jareth
This is a video going over Doug's Micromoog I just finished restoring.
This is my favorite single oscillator synthesizer and I go through of what makes it so great.
Track at the end is one I recorded several years back using only the Micromoog. I call it, " Motor Short".
Thank you Doug for giving me the opportunity to service another synth for you!
Special thanks to all of you who watch my videos as well!
Sincerely,
Jareth
this is a little different video I made a few weeks ago going over how the Hammond Bichronous model clock works. This clock is not perfect but gives you a idea how this model is able to store energy and run during a power loss. It is a hybrid between a wind up clock and a synchronous clock.
Here is the link for my other video on the Hammond Clock:
youtube.com/watch?v=eosXRbUQA_Y
Thanks for watching!
Sincerely,
Jareth
This is a little photo compilation I put together along with a original experimental track I recorded several years back.
The song features Moog Taurus 1, Polymoog 203a with Electro Harmonix Talk Box, (Vocoder), Voyager XL, Dotcom modular, and a Analog Systems sequencer.
First photos are of my 1972 minimoog (SN 1548) that I re stained several months back, the wood was starting to turn black at left hand control so bit the bullet and restored it.
Second photo sets are of a Moog Taurus 2 I restored for a local client. the sides were painted black (no photos of before) and redid the ends on it as well as electronic work.
Third photo sets are of a antique Hammond clock I restored, bought it in rough shape and got it fixed up very nice.
Fourth photo set is a Datsun 280z factory radio I restored that came from a donor Zcar. It works amazingly now.
Last photo set is from my Datsun 280z clock restore, had a broken flywheel spring so had to repair that and then adjust some circuits to compensate for the spring tension changes...keeps perfect time these days.
This is a video going over a moog 1130 Percussion controller I repaired for Eric.
Thanks for watching!
Sincererly,
Jareth
This was a sick little synth but not anymore.
Thanks Chris for giving me the opportunity to fix up your little MG-1.
Appreciate all of you that watch my videos and the support, thank you all!!
Sincerely,
Jareth
Just some updates on the 280z project. Today I tackled some preservation actions to help reduce the rust growth on this car until I get ready to perform a proper restoration. Cleaning metal and using phosphoric acid to help remove the rust. I am letting the acid dry and then will be treating it with spray paint.
I also replaced the Cowl cover with one from a donor car.
I have been daily driving this car since October and have put 1,388 miles on it. such a fun car to drive.
Thanks for watching!
Sincerely,
Jareth
This is a video going over a Moog Source I fixed up for Michael.
Thanks for watching and a Merry Christmas to you all!!
Sincerely,
Jareth
Thought I would share this track that I played on my Polymoog 203a.
This was one of those nights where I was sad because one of my friends was in his last stages of life so I was praying/worshiping Christ behind my synths and this music was a result.
Thanks for listening!
Sincerely,
Jareth
This is a video going over a Prodigy I restored for Doug.
This unit got lots of TLC and has turned into a fantastic synthesizer.
the music at the end was a experimental track I made several years back.
Thanks for watching, appreciate all the support!
Sincerely,
Jareth
Just wanted to take a few minutes today and talk a little about proper packaging procedures to make sure your units arrive safely to the buyer or shop where your synth will be serviced.
CORRECTION: I don't use 100ft of bubble wrap on all units but I do the same wrapping method for all units. Also, Most Fedex/UPS stores also have expanding foam packers that also work extremely well which can be a great alternative for peanuts.
Hope this helps.
Sincerely,
Jareth
this is a video going over a Memorymoog I restored/modified for Steve.
This one has my individual voice outputs, Kenton MIDI, Fatar keyboard upgrade, and aftertouch.
For those interested is the Fatar Keyboard:
synthtaste.com/en/shop
I was originally going to build a aftertouch circuit from scratch but during my research for the specs of the Fatar aftertouch circuits, I discovered ths board from Michigan Synth Works so purchased it. I did end up changing trimmers to multiturn for better calibration accuracy, (Not seen in my photos) and then I designed and built a harness to support this circuit.
Here is the aftertouch board for those interested:
michigansynthworks.com/products/at2cv-aftertouch-to-cv-converter
Also, those that have not heard my individual voice output mod:
youtu.be/4GAAzVUY1Lw
CORRECTION: Meant to say Atomic Dog...not Mighty Dog. Here is a link for that song reference: youtube.com/watch?v=WOOye9EB7Uo
Thanks again Steve, has been a pleasure working for you once again, (this is the same Steve that owns the Stevie Wonder Minimoog)
Special thanks to all of you that watch my videos, really do appreciate it!!
Sincerely,
Jareth
This is a little video demonstrating how electronic ignition worked back in the 70's all the way into the 80's. In this setup, I am using a iginiton system from a none California model 1976 Datsun 280z but the concept is exactly the same for California models with the exception of the extra pickup coil for electronic advance timing.
(NOTE: one thing I didn't mention was the ballast resistor connected the the + side of the ignition coil, this is roughly 1.2 Ohms and is used to help current limit the coil reducing heat)
Electronic ignition replaced the older mechanical points which were notorious for primary ignition issues back in the day.
I believe the 240z still used point based ignition if I am not mistaken.
Thanks for watching!
Sincerely,
Jareth
This is a video I made going over Val's 1973 minimoog (SN: 2527) built 5/21/1973.
This minimoog has the 2nd Voice modification that was installed back in the late 70's early 80's which gives the ability to play duophonic mode with OSC 2..pretty cool modification!
Appreciate all you that watch my videos and specal thanks to Val for the opportunity to restore your minimoog.
Sincerely,
Jareth
This is a video going over minimoog serial number 2684 (made 7/19/1973) that belongs to Knight. It has turned into a very nice and great playing unit.
Here is a link to my minimoog history video I bring up in this video:
youtube.com/watch?v=-CvP4ap_kmg&t=1779s
Appreciate you watching!!
Sincerely,
Jareth
Worked on my Zcar more today and finally remembered to bring along my camera to update all of you who are interested in my 280z project car.
The work never stops but the progress makes it all worth it.
Here are some links for the Rust treatment:
rustdepot.com
The injectors I am running in this car are:
Standard Motor Products FJ707
Shout out to @ViceGripGarage for to motivating videos he posts, always love his posts.
Appreciate you guys watching and all the support.
Sincerely,
Jareth
I went back to my basics for this track using my Roland SH-201 and vintage Arp Odyssey 2810.
Thanks for watching!
Sincerely,
Jareth


