Hydraulic Press Tool Caddy MrPragmaticLee 2022-10-08 | Using the 24" Box & Pan Brake to fabricate a tool caddy for the hydraulic press.
Machine a Pair of Parallels From an Edger Blade MrPragmaticLee 2022-12-10 | I need a pair of thin parallels so I make a pair from an old edger blade.
Sheet Metal Layout Scribe MrPragmaticLee 2022-12-03 | In this video I will machine the pieces to put together a sheet metal layout scribe.
Lathe Tool Height Gauge MrPragmaticLee 2022-11-26 | In this video I will machine a height gauge to the lathe tool heights.
Harbor Freight 120 VAC Spot Welder MrPragmaticLee 2022-11-19 | A new tool for the Tin Barn is explained and demonstrated
American Gator AR60 Air Vise Stand MrPragmaticLee 2022-11-12 | In this video I'll more recycled material to fabricate a stand for an air vise.
Simple Clevis Pin From Rusty Material MrPragmaticLee 2022-11-05 | I found a piece of rusty cold roll and turned it into a nice clevis pin.
Modifying a Harbor Freight Drill Press Clamp MrPragmaticLee 2022-10-29 | A little more work on my drill press table and a modification to a couple of Harbor Freight drill press clamps.
Tacoma Backup Camera (Where There Wasnt One) MrPragmaticLee 2022-10-22 | In this video I'll demonstrate how easy it was to add a backup camera to my 2015 Tacoma (2nd Generation) which did not come with a camera.
PowerMatic Drill Press Enhancements (Viewer Suggestions) MrPragmaticLee 2022-10-15 | Performing some enhancements to my PowerMatic drill press
Machining a Bench Block Anvil MrPragmaticLee 2022-10-01 | Got a need for another bench block anvil, so I'll machine a rusty piece of old wagon axle to make one.
Mounting Amazons Cheapest Winch MrPragmaticLee 2022-09-24 | In this video I make a removable mount for a Rugcel 2000# winch from Amazon so that the winch can be used on both my pickup and trailer.
Hydraulic Press Bending Jig MrPragmaticLee 2022-09-17 | In this video I will machine and fabricate a jig to bend flat bar in the air over hydraulic 20 ton press.
Fabricating a Step - Near Catastrophic Accident on the Drill Press MrPragmaticLee 2022-09-10 | In this video I will fabricate a step for my 1020 John Deere Tractor. In the process I make a STUPID mistake which could have resulted in a much worse injury.
Machining a sprayer hose bracket after a big OOPS MrPragmaticLee 2022-09-03 | In this video I will make a bracket to hold the spray hose on my zero turn sprayer tank trailer. Necessary after I turned the trailer over and broke the existing one.
Simple Tin Barn Equipment Repair MrPragmaticLee 2022-08-27 | My little 6" bench grinder needs some help
Sweet Corn Cutter - Lots of Lathe & Mill Work MrPragmaticLee 2022-08-20 | In this video I will "reverse build" a sweet corn cutter. Credit to Dennis Hartman for the ideaPrevious VideosPneumatic Cylinder Mountyoutu.be/jbQRFULK6owLet's Talk Pneumatic Cylinders & Control Valvesyoutu.be/KzF5yf5CfCcMaterial Listdrive.google.com/file/d/1V3altR1_TwPBAKIyY3V29juSb5yNsVyz/view?usp=sharingCutterdrive.google.com/file/d/10aVDhXkXHxVd9wxUowLsdSiI7F_-RIsA/view?usp=sharing
Lets Talk Pneumatic Cylinders & Control Valves MrPragmaticLee 2022-08-13 | In this video we will look at different style pneumatic cylinders and control valves. In particular the 5 port - 2 way valves. We'll also look at how to use the exhaust to muffle the sound and/or regulate the speed and/or move/eject parts.
Pneumatic Cylinder Mount MrPragmaticLee 2022-08-06 | As part of a much larger project I will mount an air cylinder, control valve, and pressure regulator/gauge to a piece of 3" channel iron.
New Life For An Old Edger MrPragmaticLee 2022-07-30 | Service and somewhat revival of a 16 year old driveway/sidewalk edgerYard MachinesMTDTroy Bilt
Special Use T Bolt MrPragmaticLee 2022-07-23 | Machining a T-Bolt to use on my Cub Cadet Ultima ZT1-54 zero turn mower.
Lathe Chuck Speed Handle MrPragmaticLee 2022-07-16 | Been putting it off for 6+ years, but it's time to machine a chuck speed handle.
Annual Porter Cable Air Compressor Service MrPragmaticLee 2022-07-09 | Time to service the shop Porter Cable air compressor - oil change, belt inspection, etc.
Cordless Ratchet Storage MrPragmaticLee 2022-07-02 | In this video I will fabricate a mount to store my cordless ratchets in the same area as the battery chargers.
Mounting a ScotchBrite Wheel On an Electric Motor MrPragmaticLee 2022-06-04 | As a response to a viewer comment, I machine an adapter to mount a de-burring wheel on an electric motor.
Bolt Hole Pattern on a Drill Press (No Mill, No DRO - No Problem) MrPragmaticLee 2022-05-28 | In this video I will demonstrate 2 ways to lay out a bolt hole pattern without a DRO.Previous Videos In Trig Series:Calculate Lathe Compound Angle: youtu.be/cYqzh77jbAYMatch An Existing Bolt Hole Pattern: youtu.be/LLWFHiShyJ4
Adding a Lift Handle To the Gorilla Lift Installation MrPragmaticLee 2022-05-14 | In this video I will fabricate and install a handle to compliment the Gorilla Lift.
Match an Existing Bolt Hole Pattern (BHP) MrPragmaticLee 2022-05-07 | In this video I will show the math needed to match an existing bolt hole (BHP) pattern when the diameter of the BHP is not known, nor can it be easily measured.
Gorilla Lift Installation MrPragmaticLee 2022-04-30 | Adding a Gorilla Lift gate assist to my recently acquired trailer.
Calculate Lathe Compound Angle To Turn A Taper MrPragmaticLee 2022-04-23 | In this video I will try to explain the math necessary to calculate the lathe compound angle for a given taper.Python Code simplifiedimport mathD = 4d = 1.5L = 5.5rca = round(math.degrees(math.atan(D/2)-(d/2)/L),1)print(rca)
Impact Driver Tool Caddie MrPragmaticLee 2022-04-16 | Best way to not forget you already have a tool is to store it so it is clearly visible.
Boring a Semi-Circle MrPragmaticLee 2022-04-09 | In this video I will demonstrate boring a semi-circle using your mill boring head.
Machining a simple pin with tapers MrPragmaticLee 2022-04-02 | In this video I will machine a hitch pin and turn functional tapers on both ends.
Tin Barn Tid Bit - Cable Crimp MrPragmaticLee 2022-03-26 | Just a quick tid bit on using a 1/4" nut as a cable crimp
34 Ford Roadster Rumble Seat Step Spacer MrPragmaticLee 2022-03-19 | In this video I will machine a step spacer to use in a 34 Ford Roadster restoration.
Over Designed and Over Built Receiver Hitch MrPragmaticLee 2022-03-12 | In this video I will use some of the recycled material from the last video to build a receiver hitch to pull a special tractor implement.
Recycle Farm Equipment For The Metal MrPragmaticLee 2022-03-05 | Is this video I will dismantle a J I Case 3 x 14 Bottom Plow for the metal flat bar to use on later projects.
Fabricating a ToeJack - Adding A Lift Handle MrPragmaticLee 2022-02-26 | This video will conclude the series on fabricating a couple of toe jacks. We'll add a lifting handle and a place to store the bottle jack handles.
Fabricating a ToeJack - Material Prep and Assembly MrPragmaticLee 2022-02-19 | In this video I will finish preparing the parts and assemble the toe jacks.
Fabricating a ToeJack - Bottle Jack Preparation MrPragmaticLee 2022-02-12 | In this video I will begin the fabrication of a pair of toe jacks. This video will deal with prepping the bottle jacks.
Craftsman Intermediate Tool Box Installation MrPragmaticLee 2022-02-05 | Need to install an intermediate (middle) tool box between a heavy top box and a bottom chest.
Harbor Freight Winch/Trolley Follow Up MrPragmaticLee 2022-01-29 | Things don't always go as planned. In this follow up I will machine a couple of rollers to use with the Harbor Freight winch/hoist - trolley set up.
Install 12 Foot I Beam All By Myself MrPragmaticLee 2022-01-15 | Installing the 4" x 6" x 12' I Beam For the Harbor Freight Wench & Trolley
TrimmerPlus & Other Brand Trimmer Accessories Storage MrPragmaticLee 2022-01-08 | A quick Tin Barn Tidbit on storing your cord trimmer accessories.
Harbor Freight Electric Hoist - I Beam Trolley MrPragmaticLee 2022-01-01 | In this video I will "marry" 2 pieces of Harbor Freight equipment not necessarily meant to be used together.
Merry Christmas With A Tidbit of Machining (Lathe Carriage Lock) MrPragmaticLee 2021-12-25 | Wishing all my friends and views a Merry Christmas and a happy and healthy New Year.
Fishing Boat Electric Motor Wiring Flange MrPragmaticLee 2021-12-18 | Another "hey man" job to machine a flange to accommodate installing an electric motor on a salt water fishing boat.
Zero Turn One Hand Operation Handle (Lots of Machining) MrPragmaticLee 2021-12-11 | In this video I will machine, assemble, install, and demonstrate an accessory for my zero turn mower that will allow it to be operated with one hand - allowing the other hand to handle the sprayer wand, pick up litter, etc.
