Tinning Shell for Babbitt Pour Keith Fenner 2024-05-03 | Tinning the shell of a Babbitt bearing is not always a must, but when it is called for you will have to do just that. I share my process on tinning a cast iron shell that uses a thin thickness of Babbitt as the bearing. Just like the 5-inch bearing we re-poured last week this 6-inch bearing is for a marine shaft. One other difference between sizes is this run in an oil bath versus the other being a grease lubrication.turnwrightmachineworks.comjobshopusa.locals.com/post/5318282/jobshopusamewe.com/keithfenner.52/postsrumble.com/c/KeithFennerMade in China is a warning!Vote MAGA 2024 #TRUMP Make America great again!
Spline Time Preview Keith Fenner 2024-04-27 | Pearl’s project is getting back on the making and the first part in the head stock gear box is the second in line shaft we found to be messed up. I set up the dividing head on the K&T for the spline cutting and start milling the root of the spline areas.turnwrightmachineworks.comjobshopusa.locals.com/post/5318282/jobshopusamewe.com/keithfenner.52/postsrumble.com/c/KeithFennerMade in China is a warning!Vote MAGA 2024 #TRUMP Make America great again!
Babbitt Pour 2024 Part Two Keith Fenner 2024-04-08 | I'm bringing you along on my biggest babbitt pour since I left the shipyards back in 1994. The two bearings are from a work boat and supply support for a five-inch propeller shaft, which was re-machined to new custom diameters. The Babbitt material is ASTM B-23 Grade 1 Babbitt Melting point solidus 223C 433FMelting point Liquidus 371C 700FPouring temp 441C 825F Part Two, our first attempt to pour the first lower half is a complete fail , I share the whole fail for a lesson in underestimating the flow of babbitt…Made in China is a warning!Vote MAGA 2024 #TRUMP Make America great again!
Babbitt Pour 2024 Keith Fenner 2024-04-06 | Babbitt Pour 2024I'm bringing you along on my biggest babbitt pour since I left the shipyards back in 1994. The two bearings are from a work boat and supply support for a five-inch propeller shaft, which was re-machined to new custom diameters. The Babbitt material is ASTM B-23 Grade 1 Babbitt Melting point solidus 223C 433FMelting point Liquidus 371C 700FPouring temp 441C 825F Part One, prepping for the pour, clearing the housings and making sure they mate up fine, creating the molding components and prepping the new Paragon Kiln and firing it up for the first time.Made in China is a warning label!Vote MAGA 2024 #TRUMP Make America great again!
WAZER Reaches New Altitudes Keith Fenner 2024-02-27 | WAZER Reaches New Altitudes Building my machining career in the shipyards, totally prepared my skill level to take on this aircraft engine mount project! LOL, it’s more like the WAZER pulled me through another quick and clean project with little machining needed. When I purchased my WAZER I had these kinds of jobs in mind and sometimes it’s almost like having a second person in my shop, handling the cutout and I’m off working on another part of the same job or next project at hand. “Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Bringing Life Back To One Of My Creations Part 2 Keith Fenner 2024-02-27 | Yes, you can teach an old dog new tricks and I’m a good example of just that, even if time had past between the original build and the reprograming of my FENNERIZE X-Carve machine. Sure, I have been a conventional machinist/ Jobber most of my career and then dabbled in CNC machines, first the PlasmaCAM then 3D printer, then the X-Carve machine, so found myself wanting and building my own CNC machine. I had some but very little CNC experience in a few businesses that I worked for in my career, but I really count that as zero, just because it was just not anymore than being a machine babysitter. Now I have ventured into my second 3D printing machine and looking into the additive business with real useable materials that pertain to my Job Shop USA.
Bringing Life Back To One Of My Creations Keith Fenner 2024-02-27 | Brining Life Back To One Of My Old CreationsYes, you can teach an old dog new tricks and I’m a good example of just that, even if time had past between the original build and the reprograming of my FENNERIZE X-Carve machine. Sure, I have been a conventional machinist/ Jobber most of my career and then dabbled in CNC machines, first the PlasmaCAM then 3D printer, then the X-Carve machine, so found myself wanting and building my own CNC machine. I had some but very little CNC experience in a few businesses that I worked for in my career, but I really count that as zero, just because it was just not anymore than being a machine babysitter. Now I have ventured into my second 3D printing machine and looking into the additive business with real useable materials that pertain to my Job Shop USA. “Made in China” is a warning label….Life is good! Cheers, Keithjobshopusa.locals.comWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Stick Out And No Support Keith Fenner 2024-02-04 | Sometimes the projects you have to set up in the lathe have a lot of sticking out and sometimes you can’t support the load and you have to let it hang out there to do the work. I share my set up and machining of a ductile pipe flange assembly for one of the local municipalities. “Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
How Broke Is Too Broke? Part 2 Keith Fenner 2024-01-28 | How broke is too broke 2 , I finally considered the project at hand an example of deciding when too broke is the final conclusion. I got a replacement tap and then the fun starts again, it was a snap with the second tap and the project continues and the threaded hole becomes a part….“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
How Broke Is Too Broke Keith Fenner 2024-01-25 | How broke is too broke , I finally considered the project at hand an example of deciding when too broke is the final conclusion. I ran into two machining failures during this episode. The self-setting ACME nut on my band saw needs replacing a real good example of abstract machining project.“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Im Going To Level With You! Keith Fenner 2024-01-23 | I’m going to level with you, my B&S surface grinder. I replaced the bearing and belt, now the final part of set up project, is to get it solidly on the ground and level. I bring you along on my progress…“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Another Boxing Move Keith Fenner 2023-12-19 | Machinist toolboxes, what should be in them and where should they be set up at? LOL, Fighting the flat spots in my shop is one goal that seems to be endless. Glad to be back from our trip to Greece, Turkey , Malta and Italy, jumping right back into projects and work.“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
No More Phase Converter Keith Fenner 2023-10-15 | Phase converters are a blessing when you need them, just to be able to run your machines that need it and when you can feed your shop with real 3 Phase from the pole, you really get the quiet snappy current without a secondary motor running in the background. There are a few other perks as well like slightly lower energy bills and more floor space or wall space, not to mention less noise distractions for my viewers during my videos.“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Ball Joints & Tracer Tips 2 Keith Fenner 2023-09-27 | Ball Joints & Tracer Tips, continue into Sunday to get them wrapped up for my short week. I must get a bit creative with the jig plate for the tracer ball shape but still maintain full control of adjustments and blend the second cut just right.“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Ball Joints & Tracer Tips Keith Fenner 2023-09-25 | I lead off the video with some new construction highlights in my Job Shop just before we get into the Ball Joints, we are machining replacements. We make the pattern for the tracer unit on the Clausing lathe, in our WAZER and then set it up and run the first part of the machining set ups in the Clausing Lathe.“Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Radar Mast Project Continues Keith Fenner 2023-08-27 | Radar Mast update and how this project is proceeding. I had to lead off with a WAZER project running in the background because it was important to get that project out for the customer at the same time, I wanted to get back onto the Radar mast project. I set up and welded the spreader bars into the main mast framework, welded the backup strips for the mast skins and finished with a view of surface growing and shape of the main mast coming along very nicely. “Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Radar Mast Boring Holes For The Connecting Wire Tubes Keith Fenner 2023-08-10 | Radar Mast Radar Boring Holes For The Connecting Wire TubesI set up the two components that need to have matched wire ports to feed the wire for all the accessories we are going to be adding to this project. Setting up and holding odd shapes is a challenge at times but differ ways can be applied and used like what I demonstrate in this video.Thought of the day… “Made in China” is a warning label….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Radar Mast Tack Up Tower And Skin The Spreaders Keith Fenner 2023-08-07 | Radar Mast Tack Up Tower And Skin The Spreaders I toe clamped the mast assembly down to the K&T mill table so I can tack the frame work up in a plum and level position, I share the way I like to do rosette welds on surface tacks, then set the final frame location for the spreaders.Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Radar Mast Keith Fenner 2023-07-29 | I picked up the project of building a radar mast for the 45-foot Young Brothers vessel we have been part of reconstructing during the last three years. The freedom of design to suit the needs is a great challenge and I’m up for it! From visions to Cartoon Assisted Drawing to materialize in aluminum. I start off with the framework to hold the alinement and strength needed for my project at hand….Life is good! Cheers, KeithWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Fence Post Manufacturing Drill Press Keith Fenner 2023-07-15 | I assembled my modified design of drill press for another fence company. I share the changes in design, I get to test the new filter on camera on short tig welding part of this project, share the results of the chuck runout with motor in place, and run the pneumatic travels of machine though their travels and talk about speed control.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Shear Brazing Grand Finale Keith Fenner 2023-07-06 | Lisa leads off this video’s introduction with song. I reassemble the shear back stop with the repaired component. The project is ready to be put back in action.Cheers, Keith I prep the last two pieces of the broken casting in the shear back stop project, I set them up and braze them together in two steps to keep the original alignment. Happy 4th of July everyone!Cheers, Keith Shear Brazing 3, I share the results of the brazing repair on the bearing bore end of the feed rod support project. I press out the graphite plug, check the fit and machine the rough outside surfaces to get ready for the second part of the brazing repair. I end with a share of the fun side1 I grew up water skiing as a fun activity in teens and twenties, then once when I was 50 and yesterday at the age near 65. I couldn’t get up on one ski, but went around the lake on two and had a blast….“Shear Brazing 2”, is now my top Brazing skill video made by topping the last best brazing video series, “The Million Dollar Steady Rest”. I not only braze like a 3D printer I dance you on the tripod to watch a nonstop flow of brazing rod, creating a finish bore and the near factory cast shape of the missing section on the rod support end of my repair. As soon as you know you have a cast iron project, you get into brazing mode. There are a lot of reasons the skill of brazing was one skill that was handed down to me by the first old timers I had a chance to work with in the shipyards. The strength of it, the likeness in bearing surface, the ease of machining and the non-effect it has in the base material, no crystalizing or work hardening, maybe more but these are the most important in my book. I agree to help a customer repair an old shear of his that sustained an injury during moving.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Shear Brazing 4 Keith Fenner 2023-07-05 | I prep the last two pieces of the broken casting in the shear back stop project, I set them up and braze them together in two steps to keep the original alignment. Happy 4th of July everyone!Cheers, Keith Shear Brazing 3, I share the results of the brazing repair on the bearing bore end of the feed rod support project. I press out the graphite plug, check the fit and machine the rough outside surfaces to get ready for the second part of the brazing repair. I end with a share of the fun side1 I grew up water skiing as a fun activity in teens and twenties, then once when I was 50 and yesterday at the age near 65. I couldn’t get up on one ski, but went around the lake on two and had a blast….“Shear Brazing 2”, is now my top Brazing skill video made by topping the last best brazing video series, “The Million Dollar Steady Rest”. I not only braze like a 3D printer I dance you on the tripod to watch a nonstop flow of brazing rod, creating a finish bore and the near factory cast shape of the missing section on the rod support end of my repair. As soon as you know you have a cast iron project, you get into brazing mode. There are a lot of reasons the skill of brazing was one skill that was handed down to me by the first old timers I had a chance to work with in the shipyards. The strength of it, the likeness in bearing surface, the ease of machining and the non-effect it has in the base material, no crystalizing or work hardening, maybe more but these are the most important in my book. I agree to help a customer repair an old shear of his that sustained an injury during moving.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovens
Shear Brazing 3 Keith Fenner 2023-07-04 | I share the results of the brazing repair on the bearing bore end of the feed rod support project. I press out the graphite plug, check the fit and machine the rough outside surfaces to get ready for the second part of the brazing repair. I end with a share of the fun side1 I grew up water skiing as a fun activity in teens and twenties, then once when I was 50 and yesterday at the age near 65. I couldn’t get up on one ski, but went around the lake on two and had a blast….“Shear Brazing 2”, is now my top Brazing skill video made by topping the last best brazing video series, “The Million Dollar Steady Rest”. I not only braze like a 3D printer I dance you on the tripod to watch a nonstop flow of brazing rod, creating a finish bore and the near factory cast shape of the missing section on the rod support end of my repair. As soon as you know you have a cast iron project, you get into brazing mode. There are a lot of reasons the skill of brazing was one skill that was handed down to me by the first old timers I had a chance to work with in the shipyards. The strength of it, the likeness in bearing surface, the ease of machining and the non-effect it has in the base material, no crystalizing or work hardening, maybe more but these are the most important in my book. I agree to help a customer repair an old shear of his that sustained an injury during moving.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Shear Brazing 2 Keith Fenner 2023-07-02 | “Shear Brazing 2”, is now my top Brazing skill video made by topping the last best brazing video series, “The Million Dollar Steady Rest”. I not only braze like a 3D printer I dance you on the tripod to watch a nonstop flow of brazing rod, creating a finish bore and the near factory cast shape of the missing section on the rod support end of my repair. As soon as you know you have a cast iron project, you get into brazing mode. There are a lot of reasons the skill of brazing was one skill that was handed down to me by the first old timers I had a chance to work with in the shipyards. The strength of it, the likeness in bearing surface, the ease of machining and the non-effect it has in the base material, no crystalizing or work hardening, maybe more but these are the most important in my book. I agree to help a customer repair an old shear of his that sustained an injury during moving.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Shear Brazing Keith Fenner 2023-07-01 | As soon as you know you have a cast iron project, you get into brazing mode. There are a lot of reasons the skill of brazing was one skill that was handed down to me by the first old timers I had a chance to work with in the shipyards. The strength of it, the likeness in bearing surface, the ease of machining and the non-effect it has in the base material, no crystalizing or work hardening, maybe more but there are the most important in my book. I agree to help a customer repair an old shear of his that sustained an injury during moving.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Custom Bob Cat Grill Keith Fenner 2023-07-01 | Sometimes art becomes more of your project in a Job Shop than the Physical Work. I create a Grill guard for a customer redesigning his rear radiator shroud on the back of his Bob Cat.Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Splines & Brakes Clutches & Gears 4 Keith Fenner 2023-06-24 | I set up the tool post grinder for the first time in the shop, Modify the spindle and grind the gear’s bore for the repair on Pearl’s gearbox, after a few issues.Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Splines & Brakes Clutches & Gears 3 Keith Fenner 2023-06-23 | I start the set up to grind the center of the gear that had the bore scored by the two keyways shearing and galling the bore. I mount and machine a set of soft jaws to hold the gear so it will run true , the gear pitch and the side thrust surfaces before grinding the bore true again.Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Customer Support & The Soft Rinse Keith Fenner 2023-06-22 | I work hard at having customer support second to none. I also expect the same from others and when I find it, I like to share just that. After I share customer support I show a simple way to rinse the debris down inside the WAZER enclosure. Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Splines & Gears Brakes & Clutches 2 Keith Fenner 2023-06-05 | I rough out the blanks for the two Splined shafts on the Rutland lathe, set up the new work area and then I open up a box I had packed up before the move over to my new shop.Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Splines & Gears Clutches & Brakes Keith Fenner 2023-06-03 | I share the new projects at hand as I start the rebuild of Pearl's gearbox, I Procured the materials needed to make new splined shaft and disassemble the brake hub to confirm design to be able to procure the band materials needed for it's completion. Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Setting Pearls Gear Box On Keith Fenner 2023-05-29 | Pearl is going back together once again, I set the headstock on the bed today, we will start the repairs of all the components needed inside and assemble the rest with new bearings and seals.Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
5 HP Jacobs Keith Fenner 2023-05-21 | Building a drill press for a fence company is our task at hand. I share the mounting of the Jacobs chuck to a 5 HP 3 phase motor. The disassembly of the motor to free the armature to set up in lathe and modify the end of shaft to receive the new Jacobs chuck.Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Machinist Porn Pearls Compound Keith Fenner 2023-05-18 | I have been gifted by one of my viewers, Josh Huether, with one sweet piece of Machinist porn I am blown away by his skills and generosity. Talk about the motivational push to Getter Done! Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
I Wanted To Be A You Tube Creator! Keith Fenner 2023-05-14 | I wanted to Be “A You Tube Creator” to bring on customer awareness and after many years it has done just that. Now I’m sharing my shop and talents on other platforms like RUMBLE. I have been dealing with some things in life that have caused the slowdown in my new videos being published and I share those with you as we take a look at how Pearl is sitting idle until we get back Toit! Life is good!Cheers, Keith Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearl Assemble and Level Bed Keith Fenner 2023-03-30 | Lisa and I finish up the painting on the bed components that needed to be ready for assembling of the bed to Pearl's pedestals, then I move on to the bed assembling and Lathe leveling, conclude the video with a teasing surprise... Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearl Comes Home Keith Fenner 2023-03-13 | I got the call that Pearl 's components were done and ready for pickup at Mechanics Machine Works, so I jump on the hurry up and finish prepping the pedestals and the coolant pan, as I set up the assembly location for Pearl. Lisa and I go up to Mechanics Machine Works to pick up Pearl's components and after we bring them back to shop, I get started on the painting of Pearls bed. I finish up with a little insight to the new series I'll be having called, What's in Your Machine Shop? Give-a-way" Yes, I will be putting together a shop package, Lathe, Mill and Toolbox, to give a way to a person I've been thinking about helping out for the last six months. Anyway, on with the show! Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Job Shop Friday 2/17/23 Keith Fenner 2023-02-17 | I share the day with you and a little peek at Pearl up at Mechanic's Machine Works, where she is getting tuned up.I also make a spanner wrench for another need by one of my customers, Aluminum wrench cut on the WAZER.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Job Shop Saturday 1/28/23 Keith Fenner 2023-01-29 | On any one Saturday I may be working on something to finish up work from the past week or getting things in line for the week ahead. This Saturday is a mix of both. Heat treating splines, working on Pearls paint job, assessing the damage on shaft strut and rudder refurbishment and safely disassemble a frozen water pump shaft, to save the important components of a Hercules water pump from the grave yard. Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Tooling & Fixtures 2 /23/ 23 Keith Fenner 2023-01-24 | It's sometimes a challenge to hold a part to be machined and in this video I share a set up I use to machine a modification on two steering arms for early GM. Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Scanning Pearls Handles Keith Fenner 2023-01-15 | I continue on the pearl handles project and 3 D scan both handles, sharing the new Peel 2 3D scanner and how it is working out for me. Like all tools it has a learning curve and playing with it is painless.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Whats Happening On 1/7/2023 Keith Fenner 2023-01-08 | I am so looking forward to 2023 and all the new projects I have instore, even the ones I know nothing about yet. Today we start with just a few shares then I show the start of the first repairs on Pearl, the power control handles, cleaned up and why there was failure's or was there? The evidence shown proved even the person doing the past repairs had little faith in his own work. Mr Crispin's web site for his swag; mrcrispinenterprises.comWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearls Dismantling Continues 12 /16 /22 Keith Fenner 2022-12-20 | I set up the straight edge and feeler gauge and then confirm with micrometer reading at various areas of the ways, to determine the amount of wear overall on Pearl's bed and under the carriage mating surfaces. Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearl’s Dismantling Continues 12 15 22 Keith Fenner 2022-12-20 | Today we finish removing all components to free the bed for measurements and take a good look at the wear she has endured since 1941. A little tricky removal of the quick change gear box and apron, which both really look to be in great shape from what it appears on the back side views. Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearl’s Dismantling Continues 12 /14 /22 Keith Fenner 2022-12-15 | I share a few measurement tips, I have received along the way during my career about bed wear and then remove the taper attachment and a few other items, getting that much closer to lifting off the carriage. Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearl’s Dismantling Continues 12/4/22 Keith Fenner 2022-12-05 | I am glad to be getting back into the dismantling of Pearl, looking forward to getting the control levers in my hands to start the process of duplication by 3 D printing with my metal expansion kit for the Ultimaker. Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Pearls Glasses Replaced By My WAZER Keith Fenner 2022-12-05 | Just about ready to continue with the dismantling of Pearl, we stop to look at how we created the view ports for the oil system for the head stock and apron. We cut the view ports with our new WAZER water jet machine which Wazer sponsored some of the purchase. Along with cutting the view ports I decided to cut out a X-Mas gift for my girlfriend Lisa, an ornament for the season, came out pretty good even with my limited experience in water jetting glass Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Turning A Sphere Pattern Made On My WAZER Keith Fenner 2022-11-21 | Turning a sphere, on stainless steel shafting for rudder post is part of many rudders repaired and or new manufacturing. This is the largest sphere I have set up for in the tracer here at my shop. The tracer pattern was created on my WAZER water Jet. WAZER has sponsored part of my purchase. I compare the cut difference with that of another tracer pattern I had made with the PlasmaCAM, some time ago.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovensWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
Put A Cork In It With Your WAZER Waterjet Keith Fenner 2022-11-16 | Cutting out the cork gaskets for the sight glasses on Pearl with my WAZER water jetting machine. WAZER sponsored some of my purchase price and I'm sharing how I use it in the shop, on real projects at hand with you.Wazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovensWazer's website : http://www.wazer.comLink to The Peel 2 3D Scanner: ultimate3dprintingstore.com/products/peel-2-cad-s-3d-scanner?utm_source=youtube&utm_medium=turnwrightLink to all Peel 3d Scanners: ultimate3dprintingstore.com/collections/peel-3d?utm_source=youtube&utm_medium=turnwrightLink to American Rotary: americanrotary.comHot Sot Ovens: barzindustrial.com/hotshot-ovensamericanrotary.com/product-category/hot-shot-ovens
