Olds 442 scoops. Cut & butt on a hood!!! Fitzees Fabrications 2026-09-21 | Olds 442 scoops. Cut & butt on a hood!!!
Custom dash insert made with simple tools! Fitzees Fabrications 2025-10-05 | The 49 Chevy Fleetline needs a custom dash insert cause the one that's there cannot be sourced new. time to dig out some scrap metal and see what I can come up withlink to Grinding disks.https://a.co/d/1QIB1jf
Complicated repairs using simple tools Fitzees Fabrications 2025-09-13 | As I have been saying in many of my videos.. Don't over think the repair, break it down into simple shapes and build them one at a time
Replacement panels from shelving!! Fitzees Fabrications 2025-09-02 | Making replacement panels for your project using simple tools and recycled metal. old shelving is one place to find good steel for those projects.
Rusty projects. Where do you start? Fitzees Fabrications 2025-08-23 | Have a new project? it has rust? where do you start? lets take a look at a new project I have in the shop with lots of rust and holes. Where did I start?
Vevor Orbital sander for the backyard budget! Fitzees Fabrications 2025-08-13 | Vevor Orbital Sander (5% Code: VEVT5)US Site: https://s.vevor.com/QTXOTE CA Site: https://s.vevor.com/QTXODG
Sheetmetal. Welding up the small stuff Fitzees Fabrications 2025-08-09 | Sometimes welding up the small stuff now will make the job easier and look 10 times better when finished.
One patch! Two patch! Three patch more! Fitzees Fabrications 2025-08-02 | Doing more patch work on the chopped Cab. Cut and butt everywhere. simple adjustment's turned into full replacements .
Door bottom repair. Lots of tips and tricks Fitzees Fabrications 2025-07-26 | This one is packed full of tips and tricks in doing rust repair to your classic car or truck. You even get to watch as Fitzee figures out a way to fix a problem that happens when doing sheet metal repairs.
Complicated rust repair? Take it one step at a time Fitzees Fabrications 2025-07-13 | Sometimes the most complicated repairs can be broken down into simple little sections so don't over thing the repair, take it one step at a time.
Rust paint for the win! Fitzees Fabrications 2025-07-10 | Time to get my own stuff done. time to get the 51 Chevy repainted...again!! and get it all back together and back on the road after being parked for almost 3 years
Vevor 10x15 Storage shelter. Fitzees Fabrications 2025-06-21 | US Sites:https://s.vevor.com/bfRSj4CA Sites: https://s.vevor.com/bfRSjWAU Sites:https://s.vevor.com/bfRWq3Vevor Outdoor Storage shed ( 5% codes.)
Why no videos from Fitzee? Fitzees Fabrications 2025-06-20 | I'm still here just getting those jobs done we all hate to be at. things will be getting back to normal now that these jobs are done. so stick around!
How to: Weld up large holes in sheet metal Fitzees Fabrications 2025-05-16 | Simple little trick that can make welding up large holes in your project easy. no fancy tools.
Arccaptain Mig 205 Pro vs the Mig 200 Fitzees Fabrications 2025-04-19 | Lets see what upgrades Arccaptain has come up with on the Mig 205 Pro and compare it to the other machine I been using now for over a year the Mig 200.
Budget metal brake for the hobbyist from Vevor. Fitzees Fabrications 2025-04-10 | Vevor Sheet Metal Bending Brake (5% code: VEVT5)US Site: https://s.vevor.com/bfRKOI CA Site: https://s.vevor.com/bfRKOB AU Site: https://s.vevor.com/bfRKOV been wanting a box and pan brake now some 30 years, could never afford one and used ones are hard to find. Vevor has this 24 inch metal brake that any hobbyist could afford. most of what I do is bent small sections for rust repair. this bender can do all that.
Finishing the truck cab chop Fitzees Fabrications 2025-04-06 | Simple door tops! That wont take long! Wishful thinking. lol
Using the Cut & Butt to chop a roof Fitzees Fabrications 2025-03-29 | So much cutting, welding and grinding to do a chop roof. come along and see how the cut and butt makes the job that much easier.
How does Fitzee chop a roof? Fitzees Fabrications 2025-03-21 | Come along as I chop 3 inches out of a roof of a old Ford truck cab and walk you threw the steps I take to do the job. lots of tips and tricks on this one
Autobody filler. Tips and tricks Fitzees Fabrications 2025-03-14 | Making good headway with bodywork on Crusty. going show you a number of cool tips on how to lay on filler on a large panel with a number of detail lines to deal with.
Slinging filler and then it happen!! Fitzees Fabrications 2025-03-07 | Working on project Crusty doing bodywork and all was going well until it happen! nightmare..
1950 Chevy Truck. 3 window to 5 window conversion Fitzees Fabrications 2025-02-28 | chopping up a perfectly good truck to make it better. using a roof section from a 5 window cab and graphing it into the 3 window cab.
Crusty Chronicles Firewall, floors, wheel tubs Fitzees Fabrications 2025-02-12 | A video of the complete build on the floors firewall and wheel tubs on my 1978 Toyota Corolla project called Crusty
Metal work on Crusty is Finished! Fitzees Fabrications 2025-02-02 | Finishing up the metal work on the Crusty project. The main shell needed a few more items ticked off the list before I can move on to Bodywork and paint
Finishing the trunk floor with the Cut & Butt Fitzees Fabrications 2025-01-23 | Its finally completed. The trunk floor in Crusty is done. so from firewall to tail panel from rocker to rocker there is a brand new bottom in Crusty.
More work on Crustys trunk floor! Fitzees Fabrications 2025-01-17 | continue to work on the trunk section of the project Crusty. making some interesting braces to support where the battery will go and closing in the outside sections of floor
Its fabricating trunk floor time! Fitzees Fabrications 2025-01-09 | time to get started on the trunk floor in Crusty. start off by getting the spring mounts all cut and in place and then its on to build trunk drop offs.
Fitzee got a new project! Fitzees Fabrications 2024-12-21 | I want to build everything. somethings that can be a curse.lol
Chop, Cut, Repeat! Fitzees Fabrications 2024-12-14 | Finishing off the rad support with another bunch of custom pieces and moving on to the next issue. And what a issue it was!
One piece. Two piece. Three piece more. Fitzees Fabrications 2024-12-07 | Making up nine section to reinforce the rad support on the 49 Chevy Fleetline project. lots of simple tech in this one
Finishing wheel tubs and more metal fab Fitzees Fabrications 2024-12-02 | Clueing up the wheel tubs in Crusty and getting started on closing in all the sections around the wheel tubs
Finally! Starting the wheel tubs install on Crusty Fitzees Fabrications 2024-11-23 | Must be 6 months since I built these wheel tubs for Crusty. Now that the quarters have been finalized I can start the install on the wheel tubs.
Simple repairs to Crusty turn into a nightmare! Fitzees Fabrications 2024-11-16 | Installing new leaf spring and the caltracs on Crusty to figure out where the tires will sit. Making adjustment's and cutting up the quarters and opening them up more turned into a nightmare of welding issues
Understanding patch panels Fitzees Fabrications 2024-11-01 | patch panels are designed for simple rust repair and sometimes using the whole patch panel is not the right chose. Watch how I explains the simple patch panel. This thinking is much the same for all these patch panels.
Custom built rad support for chopped 49 Chevy Fitzees Fabrications 2024-10-13 | Building a custom built rad support from scratch using what I have kicking around in scrap steel. lots to figure out and making it so it look as if it was factory installed.
Finishing up the door on Crusty Fitzees Fabrications 2024-09-29 | Finishing up the door on Crusty, it put up a fight and was not a easy repair but I got it.youtu.be/Y13T1hpUx2k?si=ZZBTYwFEjssqoqrF
Custom made panels. Basic tools Fitzees Fabrications 2024-09-21 | Building a new door handle inlay for my project Crusty. Using part of a old fence post and basic tools. Sometimes making due with what you got will give you a amazing outcome.
Crustys back. One patch at a time Fitzees Fabrications 2024-09-14 | Finally back on Crusty after it sat all summer not touched. Still have some crusty holes to repair on this car. Lets take the worse door and see if we can save it with one patch at a time
Grinding and welding tech, Cut & Butt Fitzees Fabrications 2024-09-07 | More work on the 56 olds fender sections on the 49 Chevy Fleetline. details on simple welding and grinding technics as well as some quick simple cut and butt.
Cut & Butt with flux core. Easier or harder? Fitzees Fabrications 2024-08-24 | So many people come to my channel as first time welder of sheet metal and don't have a lot of money to spend on a welder so they buy a cheap flux core welder with hopes of doing the project themselves. lets see if we can do auto body sheet metal with a cheap welder and see if the cut and butt is easier or harder to do.
Making complicated repairs simple. Fitzees Fabrications 2024-08-09 | Curved panel!! curved bead with a lip!! no problem! Just don't over thing it. brake it into sections and build one section at a time.
Fitzee using fancy tools? Cant be true.. Fitzees Fabrications 2024-07-28 | Making a repair panel for a 1936 Chevy fender. I get to use all my "fancy" tools.. well fancy to me!
Sometimes....Things dont go as planned! Fitzees Fabrications 2024-07-21 | Doing the second 56 Olds fender section on the 49 Chevy and I run into some issues! Some are mistakes by me and I needed to find a way to over come those mistakes and fix my problems.
56 Olds Fenders on 49 Fleetline Fitzees Fabrications 2024-07-07 | doing some more major mods to the 49 Chevy Fleetline. changing the headlight treatment to headlight treatment from a 1956 Olds. Took some major cutting and butting but I got it to work
One step at a time. The mirror image Fitzees Fabrications 2024-06-29 | Building the right side of the mustache section of the grill. It can be tricky but taking it one step at a time it will be fine
Sheet metal. One step at a time Fitzees Fabrications 2024-05-24 | Don't over think those hard to make sheet metal sections. no specialty tools? no problem. simple tools and take it one step at a time.
Welding up a custom bumper using the cut and butt Fitzees Fabrications 2024-05-13 | Getting all the welding done on the custom Buick bumper on the 49 Chevy Fleetline. Even got to use the cut and butt method to install section in the bumper where the original bumper guards use to mount. Building bumper brackets to mount the bumper as well.
Fitzee moves into the 21st century Fitzees Fabrications 2024-05-07 | Checking out the Vevor Burnishing polishing machine to see if it can replace the tool I have been using for 30 years!Burnishing Polishing Machine: CA site:https://s.vevor.com/bfQXXSUS site: https://s.vevor.com/bfQZ1c
Fitzees into it again! Fitzees Fabrications 2024-05-04 | Trying to move forward with the 52 Chevy and get the bumper mounted. but first I need to go backwards and deal with more ruff work that was done to the car. This needs to be addressed before the bumper can be mounted.
