Fix a LOOSE Column Shifter on Ford VehiclesDanielJaegerFilms2026-11-21 | Fix a LOOSE Column Shifter on Ford VehiclesFord Brake Pedal Fade / Goes to Floor FIXDanielJaegerFilms2023-12-18 | This Ford Edge has a problem with the brake pedal fading and sinking to the floor before the brakes grab. Ultimately, the issue lies with a sticking value in the ABS hydraulic control unit. However, this few minute trick might save you $1,000+2020+ Ford Power Window Inoperative FIXDanielJaegerFilms2023-11-01 | I've seen a lot of 2020 and newer Ford vehicles with power window problems, mostly windows being stuck open and will not close. The fix is replacing the power window switch assembly which only takes a few minutes.Ford No Start / Flashing Park / Stuck in Park FIXDanielJaegerFilms2023-10-11 | On this 2013 Ford F-350, we have a faulty transmission range sensor / neutral safety switch causing a no start / stuck in park problem. The solution is replacing the sensor, and I also show how to override the shift interlock manually in case you are stranded with this problem.Chevy Silverado 6.2 Catastrophic Engine FailureDanielJaegerFilms2023-08-18 | This 2014 Chevrolet Silverado with only 55k miles needed a new engine after the intake valve spring on cylinder #2 broke, dropping the valve into the cylinder and breaking the connecting rod.Removing Broken Cab Mount Bolts - Ford Super DutyDanielJaegerFilms2023-06-14 | After heating, soaking, not using an impact and holding the nut with a socket, both front cab mount bolts broke on this 2013 Ford F-350. Rather than remove everything from the front of the vehicle to access the broken bolt, I was able to sneak my cutting torch in and melt the down the broken bolt and slide it out of the body. Hopefully you find this helpful if you encounter the same problem!Diagnosing Cargo & Interior Light MalfunctionDanielJaegerFilms2023-04-30 | This 2011 Ford F-250 had a strange problem where the interior and cargo lights became inoperative after replacing a burnt out cargo lamp bulb. The body control module malfunctioning due to moisture intrusion is a common issue on these trucks.Ford Super Duty Dead Battery Overnight FIXDanielJaegerFilms2023-03-12 | On this 2016 F-550 truck, I traced the source of the parasitic drain to the APIM which was causing the batteries to go dead overnight.Ford Explorer Power Seat Not Working FIXDanielJaegerFilms2023-02-06 | Ford part number: JU5Z-14A699-KDA I’ve seen a number of these 2020+ model year Explorers with power seat problems end up being a blown fuse due to a mis-routed lumbar support wire harness causing the wires to pull out of the connector. While you might be able to take the connector apart and repair the terminals and wires, I find it simpler to replace this portion of the seat harness.Ford 3.5 EcoBoost P0106 Wrench Light FIXDanielJaegerFilms2023-01-01 | I recently purchased this 2013 Ford F-150 EcoBoost as a mechanic's special due to a rough idle, lack of power and multiple warning lights issue. Initially, I suspected the timing chains as the PCM had multiple codes stored in history for timing, running lean as well as a P0106 MAP sensor performance / range code. I fired the parts cannon and replaced all the timing components, which resolved the cold start rattle and timing codes, but the engine still idled rough, still lacked power and still set a MAP code and lean codes. In the end, it turned out to be a $75 MAP sensor on top of the intake manifold which took 30 seconds to replace. Now the engine runs smooth and has full power.I Bought a 2013 F-150 EcoBoost for $6kDanielJaegerFilms2022-12-15 | I've been wanting one of these trucks for a while, but with how ridiculous the market is these days, I simply couldn't justify spending the money people were asking for them, until I finally found this one.7.3 Powerstroke P1280 Electrical Issues When Hot FIXDanielJaegerFilms2022-09-01 | After chasing an intermittent electrical issue related to the ICP sensor and the alternator regulator on this truck, I finally found the wiring harness above the driver side valve cover rubbed through, causing the ICP and alternator regulator circuits to short to ground intermittently.Ford Battery Light Fix - Not the Alternator!DanielJaegerFilms2022-07-06 | This is a common issue on Ford vehicles which results in a lot of unnecessary alternator replacements which do not fix the problem.Got Lucky! 7.3 Powerstroke Misfire FixDanielJaegerFilms2022-05-28 | The owner of this truck just purchased it from a seller who stated the fuel injectors were just replaced. Obviously the mechanic who did the work needs to be fired for returning the truck to the customer like this and not fixing it.My First Solo FlightDanielJaegerFilms2022-02-05 | I've been taking flying lessons for about four months now. After three months of those lessons at approximately three lessons per week, the weather finally cooperated and I was able to fly solo for the first time. The plane is a Cessna 172S.Ford Energi Not Charging / Wrench Light FixDanielJaegerFilms2021-12-22 | In this video, I address a charing issue and warning light on a Ford C-Max Energi. I found the air inlet for the battery charger mostly clogged, causing the charger to overheat and stop charging. Fortunately it was a simple and straightforward fix, anyone with basic tools and vehicle knowledge can perform this repair.6.7 Powerstroke Low Power - Low Boost - Engine Light FIXDanielJaegerFilms2021-12-16 | This 2016 F-350 had an issue with low power, low turbo boost when cold and a check engine light, accompanied with poor fuel mileage. The issue turned out to be a faulty diesel exhaust fluid tank heater.Toyota Sienna VSC / Trac Off ProblemDanielJaegerFilms2021-12-05 | Here’s the link to the video I referenced: youtu.be/xeozboiOybU
2007 Toyota Sienna with the VSC and Trac Off warning lights on intermittently, mostly after going around turns at higher rates of speed. I found worn steering gear bushings to be the cause.Volkswagen Jetta TDI Timing Belt and ThermostatDanielJaegerFilms2021-10-08 | In this second part I replace the timing belt and components along with the thermostat. It all went back together well, fired up and ran great!Volkswagen Dual Mass FlywheelDanielJaegerFilms2021-10-07 | I had a knocking / rattling noise in my 2011 Jetta TDI at idle. The problem turned out to be a worn dual mass flywheel. In this video, I have removed the transmission to access the flywheel. There are many other components removed to access other parts I am replacing on the vehicle while it is apart.Fixing Ford Truck Doors (1999-2016) Wont Close or OpenDanielJaegerFilms2021-09-22 | While you can replace the handle, simply freeing them up with some penetrating oil will also do the trick.What Happens when Water Pump Bearings FailDanielJaegerFilms2021-09-18 | This 2007 Ram 2500 with the 5.9 Cummins Diesel engine had a water pump bearing fail. Fortunately nothing was damaged besides the actual water pump itself, which is fairly simple to replace.Testing Inverter Style Generators on my 50 amp MotorhomeDanielJaegerFilms2021-08-21 | After having some issues with the main generator on my 50 amp class A motorhome, I borrowed these two inverter style generators for a trip and was actually quite impressed with them.Cummins Water Pump FailureDanielJaegerFilms2021-08-15 | Water pump bearing failure on a 5.9 Cummins caused a terrible sounding noise and eventually threw the belt off.The Tandem Axle F-150 is Finally Done!DanielJaegerFilms2021-08-14 | After months of sitting because I was too lazy to get the work done, we've finally got the tandem axle F-150 running again and ready to drive!Broken Exhaust Manifold StudsDanielJaegerFilms2021-08-11 | While I wasn’t entirely successful with this attempt to extract the broken exhaust manifold studs, I learned it’s best to start with a welder rather than attempting to remove them with heat and an extractor.
In the next video, we replace the cylinder heads completely and install all new hardware.Chevrolet Cruze Engine ReplacementDanielJaegerFilms2021-08-05 | Replacing the engine in a 2015 Chevrolet Cruze.Chevrolet Cruze Common ProblemsDanielJaegerFilms2021-07-25 | A little overview of some common issues with the 1.4 turbocharged engine in the Chevrolet Cruze before we replace the engine in this vehicle in the next video.We all make mistakes…DanielJaegerFilms2021-07-23 | This 2005 F-150 had no cold air when the A/C was on. The owner had taken it to another shop, but they couldn't figure the problem out. Eventually, he brought it back to me. A common issue is a worn A/C compressor clutch, causing excessive clearance between the clutch and the pulley, which was indeed the case with this compressor.
However, after replacing the compressor, the A/C was still not cold. I began diagnosing further and found no power to the compressor clutch due to a blown fuse caused by a short to ground on the circuit. Further testing revealed the circuit was shorted to ground due to the A/C compressor clutch circuit diode being installed backwards at some point. My theory is due to the diode being installed backwards, it eventually destroyed the diode which allowed current to flow freely in either direction, because even after reinstalling it correctly, the circuit was still shorted to ground.
I replaced the A/C compressor clutch diode and the fuse. Finally, the truck has ice cold air again!Ford Explorer Rear Knuckle / Wheel Bearing ReplacementDanielJaegerFilms2021-05-13 | On this 2006 Ford Explorer, the brake shield had rusted, causing the parking brake hardware retainer to fall inside the rotor, which resulted in a squeaking noise. Rather than disassemble the spindle to replace just the shield and the wheel bearing, I saved a significant amount of time by replacing the entire knuckle / spindle assembly, which included a new shield, wheel bearing, bushings, hub and brake hardware.Removing a Stuck Hitch from the ReceiverDanielJaegerFilms2021-05-02 | The owner of this truck wanted to tow a trailer with it, but someone had left a hitch in the receiver for years, which eventually rusted itself inside the receiver and was seized. Using a cutting torch and an air hammer, I was able to remove it.2005 F-150 5.4 Powertrain OverhaulDanielJaegerFilms2021-04-11 | The owner of this 2005 Ford F-150 decided to keep his truck going for another 200k miles. We replaced the engine and transmission, along with another $2k in parts. Total came out to $10,391 for the job, $8,300 of which was parts.Ford Transmission Shudder FixDanielJaegerFilms2021-04-01 | After being to the dealer three times for a shudder complaint and being told there's nothing wrong with it, this 2014 Ford Explorer was brought to me. I determined the shudder to be caused by either clutch slippage or chattering in 3rd and 5th gears. At this point there are only a few options. Replace the transmission, overhaul the transmission, or try changing the fluid and adding a Lucas transmission fix additive, which is what we did in this video. And it worked!Extreme Crankcase Pressure!!!DanielJaegerFilms2021-03-10 | 6.7 Powerstroke with a rod knock also has blow by causing an extreme level of crankcase pressure that blows the oil fill cap off when loosened.Class A RV Chassis Alternator ReplacementDanielJaegerFilms2021-02-13 | A while ago, someone commented on a previous video that the voltage looked low while the engine was running. Sure enough, I noticed the engine began cranking slower in colder temperatures. Turns out the alternator was only generating 12 volts. After replacing the alternator, the gauge showed 14 volts.8.3 Cummins Cold StartDanielJaegerFilms2021-02-07 | 3 degrees Fahrenheit, no glow plugs or grid heater. Just ice cold!More Tandem Axle F150 WorkDanielJaegerFilms2021-02-06 | I find it hard to believe someone was daily driving this. The front end was very loose.Toyota P0456 Code Quick FixDanielJaegerFilms2021-01-30 | Found a cracked EVAP vent hose on the solenoid. Quick and easy fix!Fixing the Misfire on my Tandem Axle F150DanielJaegerFilms2021-01-19 | Eight new ignition coils and spark plugs later, the engine runs smooth as glass.I Bought a Tandem Axle F-150DanielJaegerFilms2020-12-20 | After a friend sent me a link to this vehicle on Facebook marketplace, I had to at least see it for myself. Sure enough, it was a legit tandem axle F-150. But why? Well, because they could I guess!Fixing the Air Horns on my RVDanielJaegerFilms2020-12-17 | The air horns work now!Engine View of the RV While DrivingDanielJaegerFilms2020-12-13 | This thing is crazy loud on the highway!LS Graveyard’s Sloppy Turbo SilveradoDanielJaegerFilms2020-12-07 | Going for a ride in the turbo LS Silverado!1998 Silverado Reverse Light FixDanielJaegerFilms2020-12-06 | Simply replacing both tail lamps on this truck fixed the reverse lamp problem.7.3 Excursion UpdateDanielJaegerFilms2020-11-27 | Seems like everyone wants to see videos of this truck, so here you go!I took the RV to a Horse Show to Keep BusyDanielJaegerFilms2020-11-23 | While my wife kept herself busy at a horse show, I brought the RV along and did some work!2020 Ford Powerstroke No Crank No Start FIXDanielJaegerFilms2020-11-15 | On some newer Ford Super Duty trucks, the PCM relay internal to the under hood fuse block can malfunction, causing the engine control module (engine computer) to not receive power. The fix is to replace the fuse block, but this quick fix will get your truck running again in an emergency situation.8.3 Cummins Low Power / No Start FixDanielJaegerFilms2020-10-28 | A common issue on both the 5.9 and 8.3 Cummins Diesel engine is a low power or no start concern caused by a faulty fuel shutoff solenoid.Dodge Chrysler Minivan Airbag Light Fix - Code B1C27DanielJaegerFilms2020-10-23 | In this video I'll show you a problem I've seen several times on the fifth generation Chrysler Town and Country and Dodge Grand Caravan minivans. The driver seat wire harness can become pinched in the seat recline mechanism, causing damage to the wiring. Fortunately it's an easy repair, the harness can be replaced easily. Hopefully this helps someone out there with the same problem!Ram Truck LED UpgradeDanielJaegerFilms2020-10-17 | Upgrading the factory halogen bulbs to LED bulbs on this 2014 Ram 3500.Shop Wanted Thousands, I Fixed It for $100DanielJaegerFilms2020-10-11 | After taking my RV to a truck shop to have a vibration issue diagnosed, I was told the problem would cost thousands of dollars to fix because the rear differential had to be overhauled. So I brought it back home and fixed it myself for $100 and a couple hours of my time. The best part is I specifically asked them three times to check the ride height, and they stated on the repair order that they “checked all suspension components” which clearly didn’t happen, or someone doesn’t know what they’re doing with air suspension. It’s a shame that I took my vehicle to the “professionals” or in the service advisor’s words “top of the line technicians” only to be told it needed thousands of dollars of work, which it clearly didn’t, and I end up fixing it myself.