Harvard Natural Sciences Lecture Demonstrations
Color Subtraction
updated
The battery is a 12 Volt gel cell. The wires have a total resistance of about 0.1 Ohms. The magnet is about 0.3 Tesla between the poles.
For more details about our setup, see https://sciencedemonstrations.fas.harvard.edu/presentations/jumping-wire
The 8 cm diameter plastic ball is mounted near the edge of a 46 cm diameter disk and is driven by a Bodine Electric Co type NS1-33R speed reducer motor. The disk is cut from 1/8" thick masonite. The mass weighs 20 N, and was fortunately paired with a spring to match the speed of the motor. Illumination is provided by a Kodak slide projector.
Thanks for watching!
The camera we use is a FLIR E-95, which can detect wavelengths in the 7.5-14 micron range. Never attempt to drink liquid nitrogen!
At room temperature the wax is slightly more dense than the water, but when it's heated it expands and becomes more buoyant, causing it to float up toward the top, where it cools and loses its buoyancy. This convection cycle is thought to model the behavior of hot magma beneath the surface of the Earth.
Thanks for watching!
Thanks for watching!
For more details on our setup, see https://sciencedemonstrations.fas.harvard.edu/presentations/metals-acid
Thanks for watching!
Two 500ml soda bottles of the same make, split a bottle of vinegar between them.
11" balloons are pre-inflated with dry air, with care taken not to stretch the neck of the balloon. Into the balloons with a funnel go one, two teaspoons of baking soda. With 250 ml of vinegar, that's like six liters of gas potential if one carbon dioxide comes from one acid hydrogen ion.
For more details on how we set up and do this demo, see
https://sciencedemonstrations.fas.harvard.edu/presentations/limiting-reagent-vinegar-or-baking-soda
Thanks for watching!
For more details on our setup, see
https://sciencedemonstrations.fas.harvard.edu/presentations/polarization-scattering
Thanks for watching!
For more photos of our setup, see
https://sciencedemonstrations.fas.harvard.edu/presentations/tower-spectra
Thanks for watching!
Always wear proper PPE when working with chemicals!
Always wear proper PPE when working with chemicals!
For lots more details on our setup, see https://sciencedemonstrations.fas.harvard.edu/presentations/radio-wave-properties
References
* Richard Schwenz and Lynn Geiger. "Photon-Initiated Hydrogen-Chlorine Reaction." Journal of Chemical Education 76.4 (1999): 470.
* Shakhashiri, Bassam Z. "Chemical Demonstrations: A Handbook for Teachers of Chemistry." Madison: The University of Wisconsin Press, 1983. ( http://books.google.com/books?id=0rx6Cjx_l-AC&lpg=PP1&pg=PA121#v=onepage&q&f=false)
The top and bottom of the drum has a radius of about 30 centimeters, and it is about 1 meter tall. This means the atmosphere pushes down on the top of the drum with about 6,500 pounds of force! We leave the calculation of the force on the sides as an exercise to the student.
We pump on the drum with a Varian SD-200 vacuum pump. Usually the initial collapse will occur after a minute or two. The drum seen here actually underwent initial collapse after 35 seconds of pumping; the footage was edited to make it more watchable.
For more details on our setup, see https://sciencedemonstrations.fas.harvard.edu/presentations/55-gallon-drum
In nature, chaotic behavior readily occurs in turbulent flows and in large-scale weather patterns, but scaling these systems to a laboratory or classroom setting is far from trivial. The idea of building a waterwheel as a discrete, mechanical example of a chaotic system was proposed and realized by Willem Malkus, Louis Howard, and Ruby Krishnamurti in the early 1970s. According to Edward Lorenz, their original design “was a precision instrument, suitable for controlled laboratory experiments.” Our design is simpler and geared more towards pedagogical impact than experimental fidelity, but we think you will find it charming and instructive nonetheless.
For more details on our setup, including links to download some of the clips of the wheel in motion, see https://sciencedemonstrations.fas.harvard.edu/presentations/chaotic-waterwheel
We have two tanks of equal dimension next to each other. The first tank has a row of 16 tubes inserted near the bottom, all of equal length, and are 0.101" in diameter. The second tank has a single tube inserted with nearly twice the diameter (0.207") and equal length as the others. An equal amount of water is added to the tanks, so that the pressure difference between the ends of all 17 tubes is the same. With the fluid viscosity, pipe length, and pressure difference the same among all the tubes, the only difference is their radii.
The valves to all the tubes are opened simultaneously, and we see that the flow rates are very nearly equal--even over the course of several minutes. (The difference in water levels seen at the end of the experiment was measured to be roughly 5 percent.)
For more details on our setup, see https://sciencedemonstrations.fas.harvard.edu/presentations/poiseuilles-law
Some of you may notice that the white bucket glows with the same color as the laser light, even after the water has stopped flowing into it! How can this be? Does the light keep reflecting around inside the bucket? Did we somehow find a way to violate conservation of energy? This part of the demo is a trick, of course: a network of red LEDs line the bottom of the bucket!
For more details on how we set up this demo, see
https://sciencedemonstrations.fas.harvard.edu/presentations/bucket-light
The video clips used in this video are in 240 fps and can be downloaded from here
drive.google.com/drive/folders/14uo9H39-arDLdm4ZrjwhE60ejy_pHzsy?usp=sharing
The platform is roughly 30 cm long. The steel ball is roughly 200 grams.
A small ball of iron and a chunk of brick are placed inside a muffle furnace that has been preheated to about 1000 C. The interior walls and heating elements of the hot furnace have a bright, yellowish glow to them. The samples of iron and brick, on the other hand, are at room temperature (about 25 C) when they are first inserted, and so their brightness and color make them stand out against the hot background. The samples are heated for about 30 minutes, which is enough time for both of them to reach the same temperature as the interior of the furnace. When the door is opened, we see that the samples glow with nearly equal intensity and color as their surroundings!
When the samples are removed from the furnace, we see that they both start out at nearly the same brightness and color. As they cool they become less bright, and the colors they emit gradually move toward the red part of the visible spectrum.
Seen here is a Blue M Electric Company Lab-Heat M-10A muffle furnace. For more details on how we do this demo, see https://sciencedemonstrations.fas.harvard.edu/presentations/black-body-radiation-oven
One can draw an analogy with this demo and onshore breezes that occur along the coast on hot summer days. In that case, air heated by land rises up and is replaced by cooler air moving in from over the ocean.
The tank was custom built at Harvard Bio Labs Machine Shop in Cambridge, MA; it is about 14" x 10" x 2" and is made out of acrylic. The heater is a 125W Cenco Knife Type Immersion Heater connected to a Variac. About 20 drops of concentrated rheoscopic fluid were added to distilled water.
Special thanks to Dr. A. Klales, who first suggested we try this experiment, and also thanks to J. Peidle, for showing us how to externally trigger the strobing LED!
Without the color filters, the brightness of the schlieren image only gives us information about the magnitude of the pressure changes in the standing wave. We can now use the color information to tell us whether the pressure is increasing or decreasing. Each colored band is a pressure antinode that is oscillating between high and low pressure.
The order of the color bands in the standing wave depends on the relative phases of the strobe light and the transducer. Although we do not show it here, shifting the phase of the strobing light source by 180 degrees causes the colors in the standing wave to reverse.
The color filters we use here are Kodak Wratten 2 color filter #29 (red) and #61 (green).
More information about our schlieren optics set-up and how it works can be found on our Science Demonstration website: https://sciencedemonstrations.fas.harvard.edu/presentations/schlieren-optics
Safety Note: Although 28 kHz is beyond the range of human hearing, ear protection should be worn whenever attempting this experiment to avoid damaging vibrations in parts of the ear. Any high-pitched whines you hear in this video are not dangerous.
More information about our schlieren optics set-up and how it works can be found on our website: https://sciencedemonstrations.fas.harvard.edu/presentations/schlieren-optics
Safety Note: Although 28 kHz is beyond the range of human hearing, ear protection should be worn whenever attempting this experiment to avoid damaging vibrations in parts of the ear. Any high-pitched whines you hear in this video are not dangerous.
Images employing schlieren optics are very sensitive to changes in the density of air. Since sound waves are pressure waves, and pressure variations result in density gradients, it stands to reason that one should be able to image sound waves traveling through the air. Unfortunately, the waves move at the speed of sound (343 meters per second), which makes it difficult for us to see them. With stroboscopic animation, we can slow down the apparent motion of the sound waves.
Some of you probably wonder whether this experiment would work with audible sound waves at, say, 1 kHz (about 34 centimeters in wavelength). Not only is that wavelength much bigger than our mirror, but it turns out that our optical setup is not sensitive enough to see the density gradients formed by 1 kHz sound (at least not at a Sound Pressure Level that is less than that of a jet engine). We can, however, see the the density gradients formed by 28 kHz sound waves, which have a wavelength of about 1.2 centimeters.
We use here an 18" diameter, f/4.3 concave mirror that we salvaged from a spectrometer. The light block is a size 7 piano wire, mounted at 45 degrees with respect to the vertical on a lens holder. The light source is an Engin LZ4-00CW08 cool white LED. The transducer is an American Piezo 28 kHz Cleaning Transducer model #90-4040 and is driven by a Samson Servo 120 power amplifier.
More information about our schlieren optics setup and how it works can be found on our Science Demonstrations website: https://sciencedemonstrations.fas.harvard.edu/presentations/schlieren-optics
Safety Note: Although 28 kHz is beyond the range of human hearing, ear protection should be worn whenever attempting this experiment to avoid damaging vibrations in parts of the ear. Any high-pitched whines you hear in this video are not dangerous.
Details of our Schlieren optics set-up can be found on our website: https://sciencedemonstrations.fas.harvard.edu/presentations/schlieren-optics
Images employing schlieren optics are very sensitive to changes in the density of air, and these changes refract light into the camera. Note that the little spheres settle down where there are bright bands of light. The bright bands of light in the schlieren images are known to be the result of either increasing or decreasing air pressure with respect to vertical position—in other words, the pressure nodes.
For an excellent writeup by David P. Jackson and Ming-Hua Chang on the mechanics of acoustic levitation, see American Journal of Physics 89, 383 (2021); doi.org/10.1119/10.0002764
For more information on our schlieren optics set-up, see
http://sciencedemonstrations.fas.harvard.edu/presentations/schlieren-optics
Although 28 kHz is beyond the range of human hearing, ear protection should be worn whenever attempting this experiment to avoid damaging vibrations in parts of the ear. The sound you hear in this video is not ultrasound but rather a subharmonic and is not dangerous to your ears.
As the surrounding air is drawn to the flame, it is deflected from the center of the turntable as it passes through the openings in the screen. The resulting angular momentum of the gases helps to form a tall, twisting column of fire.
FIRE IS HOT!
For more information on our setup, see
http://sciencedemonstrations.fas.harvard.edu/presentations/vacuum-cannon
For more details, see
http://sciencedemonstrations.fas.harvard.edu/presentations/sodium-absorption
For more information on our setup and references for further study, see http://sciencedemonstrations.fas.harvard.edu/presentations/reverse-sprinkler
The ceramic material is a 25mm disc of yttrium barium copper oxide (YBa2Cu3O7, also commonly referred to as "YBCO”). The YBCO has a critical temperature of 90K and is cooled with liquid nitrogen, which boils at 77K. The magnet is just under 5mm per side and weighs about 0.8 grams.
The magnet is able to levitate due to its interaction with persistent electric currents that expel external magnetic field from the interior of the superconducting YBCO. (The details of this interaction are complicated, and cannot be fully explained using classical physics.)
For more details on our setup and references for further study, see http://sciencedemonstrations.fas.harvard.edu/presentations/meissner-effect
Also check out this video from the Annenberg Foundation on high-temperature superconductor research http://www.learner.org/courses/physics/video/vid_byunit.html?unit=6&vidNum=1
For more details on this demo see http://sciencedemonstrations.fas.harvard.edu/presentations/nuclear-fission
Starting at about 1:12, the colors seen in the upper section of the ring are roughly what we would expect from a linearly increasing film thickness. Meanwhile in the lower section the thickness is changing in a more complicated way, and the colors appear washed out.
The soap film shown here consists of 2/3 cup of Dawn liquid dishwashing soap, 3 tablespoons of glycerol, and 1 gallon of water. We guess that the average index of refraction of the solution is close to that of water (about 1.33). The footage was taken July 16, 2014—the third consecutive day of rain and high humidity in Cambridge, MA. The light source is a portable fluorescent light box with a color temperature of between 4500 and 5000 Kelvin.
The camera used is a Blackmagic Cinema MFT with a Vivitar Auto Wide Angle 35 mm lens. The footage was shot at 800 ASA in CinemaDNG RAW 2.5K and color corrected using DaVinci Resolve 10 Lite.
For further study, see
http://sciencedemonstrations.fas.harvard.edu/presentations/thin-film-interference
Physical Science Study Committee, Physics, (D.C. Heath, 1960) Chapt. 19 sect. 9 "Interference in Thin Films.”
Leslie J. Atkins, Richard C. Elliott, Investigating thin film interference with a digital camera. Am. J. Phys. 78, 1248 (2010); http://scitation.aip.org/content/aapt/journal/ajp/78/12/10.1119/1.3490011#
http://hyperphysics.phy-astr.gsu.edu/hbase/phyopt/soapfilm.html
At about 1:20, the colors seen in the upper section of the ring are roughly what we would expect from a linearly increasing film thickness. Meanwhile in the lower section the thickness is changing in a more complicated way, and the colors appear washed out.
The soap film shown here consists of 2/3 cup of Dawn liquid dishwashing soap, 3 tablespoons of glycerol, and 1 gallon of water. We guess that the average index of refraction of the solution is close to that of water (about 1.33). The footage was taken July 16, 2014—the third consecutive day of rain and high humidity in Cambridge, MA. The light source is a portable fluorescent light box with a color temperature of between 4500 and 5000 Kelvin.
The camera used is a Blackmagic Cinema MFT with an Angenieux 20-80 mm zoom lens. The footage was shot at 800 ASA in CinemaDNG RAW 2.5K and color corrected using DaVinci Resolve 10 Lite.
For further study, see
http://sciencedemonstrations.fas.harvard.edu/presentations/thin-film-interference
Physical Science Study Committee, Physics, (D.C. Heath, 1960) Chapt. 19 sect. 9 "Interference in Thin Films.”
Leslie J. Atkins, Richard C. Elliott, Investigating thin film interference with a digital camera. Am. J. Phys. 78, 1248 (2010); http://scitation.aip.org/content/aapt/journal/ajp/78/12/10.1119/1.3490011#
http://hyperphysics.phy-astr.gsu.edu/hbase/phyopt/soapfilm.html
This movie shows a basic, qualitative demonstration of the presence of subatomic particles; techniques to more accurately identify and measure individual subatomic particles are possible with this apparatus.
The cloud chamber was first developed by C.T.R. Wilson around the turn of the 20th century to study optical phenomena associated with mist and clouds (he received the Nobel Prize in 1927). When charged particles ionize a supersaturated vapor, a trail of ions is left in the path of the particles. The ions act as condensation nuclei for the alcohol to condense on, and a thin line of fine droplets is formed in the path of each particle.
The range of the alpha particles from the thorium source is about 4 cm. As the alpha traverses its path, it slows down gradually and becomes more heavily ionizing by virtue of the fact that it spends more time in the vicinity of air molecules in its path. Evidence for this can be seen by observing that the tracks become denser with increasing distance from the source.
This particular diffusion cloud chamber was built by Supersaturated Environments of Madison, WI (http://www.cloudchambers.com). Dry ice pellets under the chamber floor help to create a steep temperature gradient from top to bottom. Felt strips along the top of the chamber are soaked with 95% ethanol. The viewing area is 51 square centimeters, with inscribed "+" marks every 10 centimeters. The special slide inserted into the Kodak Ektagraphic III projector saves the viewing audience from unnecessary glare.
REFERENCES
* W. Gentner "An Atlas of Typical Expansion Chamber Photographs" Pergamon Press, 1954.
* E.W. Cowan, "Continuously Sensitive Diffusion Cloud Chambers" Review of Scientific Instruments 21, 991 (1950)
* R. Cases, E. Ross, J. Zuniga "Measuring Radon Concentration in Air Using a Diffusion Cloud Chamber" Am. J. Phys. 79, 903 (2011)
For some more details on our setup see:
http://sciencedemonstrations.fas.harvard.edu/presentations/cloud-chamber
Seen here are the heated gases from a candle flame and a hair dryer, helium gas, and sulfur hexafluoride gas.
For more information on our setup please see
http://sciencedemonstrations.fas.harvard.edu/presentations/schlieren-optics
Note that this version of the setup uses a white LED flashlight instead of an automotive light bulb.
Thanks for watching!
For more references and info on our setup see
http://sciencedemonstrations.fas.harvard.edu/presentations/relativity-train
For more information on Prof Papaliolios see http://www.news.harvard.edu/gazette/2004/05.13/18-mm.html
In this video we see the spring-powered gun shooting the same steel ball bearing with two different initial velocities in an attempt to show that the initial speed of the ball does not matter. The shots at 0:51, 1:00, and 1:09 are close to the maximum speed (roughly 13 m/s), while the shots at 1:18, 1:27, and 1:34 are close to the minimum (roughly 9 m/s). All other parameters remain the same for all trials; the horizontal distance is about 6.9 meters, and the launch angle is about 23 degrees above the horizontal.
Mechanical analog of a "Paul Trap" particle confinement—a ball is trapped in a time-varying quadrupole gravitational potential. A large saddle shape (attached to a plywood disk) is mounted on a multi-purpose turntable. The saddle shape is essentially a quadrupole gravitational potential. Rotation of this potential subjects the ball to an alternating repulsive and attractive potential, much like the time-varying electric quadrupole potential of a Paul Trap used in trapping single ions or electrons.
The plastic ball used here is about 25 cm in diameter and was purchased at a toy store. The saddle consists of a rubber sheet and fiberglass, and was hand-made with help from Justin Georgi. The turntable is driven at about 110 rpm with a DC motor. We have observed this ball at this speed remaining stable for over 2 hours.
Slow motion footage recorded at 240 fps with a Casio EX-FH25. Thanks to Rob for letting us use the camera.
For more information on our demo and references for further study see http://sciencedemonstrations.fas.harvard.edu/presentations/rotating-saddle
The physical pendulum seen here is mounted on a ball-bearing pivot and can rotate 360 degrees; the pivot is driven at about 50 Hz with an amplitude of about 1 cm (3/4" per stroke) by a Sears Craftsman Auto Scroller Saw (model 315.172090); the length is 45 cm and the center of mass is slightly above 15 cm from the pivot; the rotational inertia is roughly 4x10^(-4) kg*m^2; the mass is about 100 grams.
For more details and references for further study see:
http://sciencedemonstrations.fas.harvard.edu/presentations/inverted-pendulum
Shot in 24 and 300 fps. Thanks to Rob, Fu, and Daniel for their help.
When fluid flows around a cylindrical object, there is a range of flow velocities for which a von Karman vortex street is formed. The shedding of these vortices imparts a small, periodic force on the object. Here the object is a cylinder attached to a physical pendulum whose frequency of oscillation is adjustable. The end of the cylinder is submerged in flowing water. When the frequency of the pendulum is adjusted to match the frequency of vortex shedding, the cylinder swings transverse to the direction of flow with a peak-to-peak amplitude of a few centimeters.
For more details on our setup as well as references for further study see http://sciencedemonstrations.fas.harvard.edu/presentations/vortex-shedding
We send O2 gas through a copper coil, which is then immersed in about 2 liters of liquid nitrogen (77 Kelvin, or minus 196 degrees Celsius). As the O2 travels through the coil it loses enough heat to change from a gas to a liquid, and that liquid is collected in a small pre-cooled Dewar. Liquid nitrogen is poured between the poles of the permanent magnet, but since its diamagnetic properties lead to only a very weak interaction with the field, it just sloshes through as if it were water. The liquid oxygen, on the other hand, sticks between the poles of the magnet until it boils away.
Because the oxygen molecule has an electronic structure that favors the non-cancellation of two of the electron spins, its net magnetic moment is free to point in the direction of an external magnetic field (just as a compass needle does). When enough of these moments are aligned, the material as a whole behaves like a single magnet. At room temperature only a small fraction of the moments are able to line up perfectly with the external field, but when oxygen is cooled and condensed into a liquid the effect is more noticeable.
For more details on our setup see:
http://sciencedemonstrations.fas.harvard.edu/presentations/paramagnetism-oxygen
Like us on Facebook! http://www.facebook.com/NatSciDemos
Two ceramic lightbulb sockets are wired in series to a household AC power cord. When two incandescent bulbs of the same Wattage rating are screwed into the sockets and the cord is plugged in, they both pass the same amount of current and so they both light with the same intensity. When one bulb is unscrewed, the circuit is broken and the other bulb goes out. If we can replace the missing bulb with a conductive material, the circuit will once more be complete and the remaining bulb will light again.
For more details on our setup, see http://sciencedemonstrations.fas.harvard.edu/presentations/conductivity-glass
For more details on our setup see http://sciencedemonstrations.fas.harvard.edu/presentations/coffee-mug-string
Special thanks to Rob and Nils.
Like us on Facebook!
facebook.com/NatSciDemos
For more details on this setup, see
http://sciencedemonstrations.fas.harvard.edu/presentations/balancing-forks
For more details on our setup see:
http://sciencedemonstrations.fas.harvard.edu/presentations/shattering-wineglass


