How To Print Problem Free PETG On Wham Bam PEX Wham Bam Systems 2026-09-21 | How To Print Problem Free PETG On Wham Bam PEX
Intro to the Resin Hotbox Enclosure and How It Helps Get More Consistent Prints Wham Bam Systems 2022-11-12 | The Resin HotBox was created to get consistent results and fewer failures with a temperature-controlled ambient resin printer enclosure. Almost every resin prints better at specific temperature ranges, especially the higher-performance and exotic resins. The Resin HotBox enclosure also helps to trap fumes and has a built-in port to add fume extraction.00:04 Introduction00:18 Why Do You Need An Enclosure For A Resin Printer?01:27 Features03:25 Instant Access to Machine04:09 Size and Machine Fits05:47 LED USB BAR for Resin06:23 Unboxing and Set Up9:54 ConclusionThe Resin HotBox is 330mm wide x 330mm deep x 580mm tall and fits the following printers:AnyCubic: Photon, Ultra, S, SQ, Mono, Mono SE, X, 4K, X 6K, M3, D2 DLPCreality: Halot, Halot One, Halot One Pro, Halot One Plus, Halot Lite, Halot Sky, LD002 H, LD002 R, LD 006Elegoo: Saturn, Saturn 2 8k, Saturn 8K, Mars, Mars Pro V2, Mars C, Mars 3, Mars 3 Pro, Mars 3 Ultra 4kEPAX: E10, E10 8K 10.1, E10 4K, E10 4K 8.9 , E10 5K 10.1, E6 6” 2K, Flashforge: Foto 9.25, Foto 8.9, Foto 6.0Kelant: C60, FlareKudo: Bean, Bean PlusLonger: Orange 10, Orange 30, Orange 4KPhrozen: Sonic Mini, Mini 4K, Mini 8K, Mighty, Mighty 8KVoxelab: Proxima 6.0 2K, Proxima 6.0 4K, Proxima 8.9 4k, Polaris 2KUniz: IBEESend us an email if you can confirm any other machine fits not listed and we would be happy to offer you a coupon or gift: technical@whambamsystems.comFor printable HotBox accessories, visit our HotBox support page: whambamsystems.com/hotbox-supportAll of our HotBox lines are made of high-grade Nylon 600D fabric with fire-resistant coating and lined with a metallic heat-deflecting internal liner that sandwiches around a strong, lightweight honeycomb insulating structure. It has a temperature gauge right on the front panel so you can monitor the internal temperature. You can allow the heat of the machine and the catalytic reaction of curing resin to maintain temperatures or add a small heater.Features of the Resin HotBox enclosure include:-Lightweight semi-rigid construction-Excellent insulating properties-Folds up flat, is easy to store and transport-Front USB outlet and extension cable-Cable passage for power or other cables-Full view front window covered with an anti-UV film to allow viewing the print-Built-in thermometer (two LR44 batteries not included)-Passage with cover for user-added fume extraction and air filtering-A set of loops to hold a LED light bar-Built-in top handle to lift the enclosure when neededWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
New Addition To The Slap Mat Family Wham Bam Systems 2022-11-06 | A quick video to show you our entire lineup of Slap Mats! We introduced our original Slap Mat 3 years ago, followed by our Mega Slap Mat, and recently our Mini Slap. All of the Wham Bam Slap Mats are made of pure 100% first-grade silicone and will not be harmed by printer resins or most chemicals! They are also great as a general craft mat, protecting your work surface from gluing, body putty, painting, or even resisting melted solder and the tip of most soldering irons for up to 3 minutes!Shop our collection of Slap Mats: whambam3d.com/collections/slap-matsFrankenstein's Monster model by FotisMint: myminifactory.com/object/3d-print-frankenstein-s-monster-bowl-pre-supported-251325Alien - Xenomorph model by Printed Obsession: myminifactory.com/object/3d-print-alien-xenomorph-full-figure-25-cm-82660Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Final Testing of the Cloud - Personal Printer Sentry Wham Bam Systems 2022-10-19 | Here is the final testing of one of our newest products, the Cloud, a personal 3d printer fire extinguisher. In this video, we test both inside our HotBox enclosure and directly on the 3d printer without enclosure. The results were explosive!Enjoy peace of mind when leaving your printers unattended with the Cloud, learn more:whambam3d.com/products/the-cloud-personal-printer-sentrythe Cloud will only activate with direct contact with a flame for 3-5 seconds and will not trigger due to ambient temperature or smoke. Once activated it makes a brief explosion launching a cloud of ABC extinguishing powder into the air around the device. The powder quickly extinguishes almost any fire within its perimeter. Rated as a Class A, B, C, E, and F fire extinguisher. Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Fix Clogs, Change Nozzles, Swap To Direct Drive In Seconds Wham Bam Systems 2022-06-17 | With the MUTANT you can replace a clogged hot end, change the nozzle size, or swap between direct drive and Bowden in only seconds. Whether you are running a full print farm where downtime costs you money or just sick that your only printer is down again, the MUTANT can change your life!**For a limited time**Buy a MUTANT QUAD and get a Workstation free! Add both items to your cart and use the code ‘FreeWS’ at checkout, valid thru June 23rd!Learn more here: whambamsystems.com/mutantWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinting
HotBox Mega - New Product Overview Wham Bam Systems 2022-05-06 | The Wham Bam HotBox Mega is a lightweight, easy to assemble, and easy to store away 3d printer enclosure. If you want to print ABS, Nylon, PC, and other high-temperature filaments, an enclosure is a must to maintain the steady ambient temperature needed for success. See the entire HotBox product line here: whambam3d.com/collections/hotboxIndex:0:06 Introduction0:13 HotBox Original vs HotBox Mega0:46 Measurements 1:08 Why do you need a HotBox?2:04 Easy Set-Up3:23 LR44 Batteries3:52 Easy Install on your Printer5:10 Features6:02 LED USB Barthe HotBox Mega measurements are 700 x 700 x 640 MMS (LxWxH) and it was designed to fit most 300x300 machines including: Creality CR-10Creality CR-10 V2Creality CR-10 V3Creality CR-10 ProCreality CR-10 MiniArtillery SidewinderAnet A8 PlusAnycubic Mega XBiqu ThunderGeeetech A20MHictop CR-10Tevo Black WidowLulzBot Taz Pro SMakeGear M2Monoprice MP10TronXY XY-3 / XY-2JG Maker Artist D DualWeedo X40May Fit: *Tenlog TL-D3, *Geetech A30, *Tevo Tornado *some taller printers may require 3D printed lifter feet which you can find here:thingiverse.com/thing:4060350Find the most up to date list of printers that fit the HotBox Mega here: whambam3d.com/products/hotbox-mega-3d-printer-enclosureSee our support page for more info: whambamsystems.com/hotbox-supportIf you can confirm an unlisted machine fit, we would be happy to give you a coupon of appreciation! Please send an email to technical@whambamsystems.comWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Changing the FEP on a Resin Printer Wham Bam Systems 2022-04-05 | A step-by-step video to help guide you through the first time you need to change your FEP sheet on your resin printer. Find links for some of the tools and materials used below and let us know in the comments if you have any FEP tricks to share!0:01 Introduction0:10 When to Change0:40 Tools and Materials Needed1:40 Removing Old FEP3:10 Cleaning Vat and Parts5:05 Putting Everything Back TogetherColor-coded Hex Drivers: amazon.com/gp/product/B01FK6TJ9GCordless screwdriver (similar to the one in the video but Black and Decker): amazon.com/DECKER-AS6NG-Alkaline-Cordless-Screwdriver/dp/B004HY3APWMetric driver bits: amazon.com/01148A-11-Piece-Magnetic-Release-Compatible/dp/B086RJW49QNFEP: amazon.com/Siraya-Tech-Pcs-NFEP-Film/dp/B09MRGRF4MSlap Mat: whambam3d.com/collections/slap-matsWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#FEP #ResinPrinting
Filter Your Resin Infused IPA In 3 Steps Wham Bam Systems 2022-01-22 | 3 step process to effectively filter your resin-infused isopropyl alcohol (or IPA for short) and reuse it! 1. Pour the dirty IPA through a filter into a glass jar.2. Let the jar sit in the sunlight and allow sediment to harden and drop down to the bottom.3. Siphon off the clean IPA and dispose of the sediment at the bottom. Let us know in the comments if you have had success with this process or if you have other great ideas for filtering IPA!We find that 99% IPA works best for cleaning resin prints and we use a lot of it, so we buy it in gallon jars: amazon.com/gp/product/B08LNZWXMJGlass jars: amazon.com/gp/product/B075JQR2KDSiphon: amazon.com/gp/product/B07VWVMQKDFilters 50 -190 micron: amazon.com/gp/product/B08H1R61W3Funnels: amazon.com/gp/product/B07Q2S1LQ3Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Transforming Your Printer Into Unlimited Possibilities With One Modification Wham Bam Systems 2021-11-08 | the MUTANT™ V2 is the only mod for your 3d printer that allows you to have unlimited transformations! the MUTANT™ gives your FDM printer the ability to quickly and easily change your entire hotend and add other tools such as a laser cutter, pen plotter, food plunger, ceramic and/or clay extruder, dial gauge, vinyl cutter, and nearly anything you think of, all driven by the machine’s mechatronic components! Learn more about the MUTANT™ V2: whambamsystems.com/mutantSee the entire MUTANT product line here: whambam3d.com/collections/mutantSee all the downloadable files here: whambamsystems.com/mutant-supportUse the MUTANT to quickly swap out for:00:05 Clogs or maintenance00:13 Different nozzles sizes00:23 High-performance hot-ends and direct drives 00:30 Marker pen plotter 00:37 Drag knife vinyl cutter00:48 Food and icing extruder 00:54 Dial gauge indicator01:00 Laser cutter and engraver01:05 Clay, Ceramics, or Porcelain extruderHere is a list of models, materials, and other credits from this video:Monkey material - Polyalchemy Elixir PLA Alpha Brass: polyalchemy.com/collections/elixir-plaWall Hanging Monkey Set by Creator Digital: cults3d.com/en/3d-model/art/monkeys-morillasfelipeRocket material - Polyalchemy Elixir PLA Lucid Pearl: polyalchemy.com/collections/elixir-pla gCreate Official Rocket Ship: cults3d.com/en/3d-model/game/gcreate-spiral-vase-rocketWrench material - X CarbonX, Nylon G3 + Carbon Fiber: www.3dxtech.comFully Assembled 3D Printable Wrench model by barspin: thingiverse.com/thing:139268Printed using the @sliceeng Slice Engineering Mosquito Hotend and Bondtech DDX Direct Drive.PCB material made with Acid Resist Pens: amazon.com/gp/product/B07PM1QCT8Copper Clad PCB Blanks: amazon.com/gp/product/B01MCVLDDZPen Plotter Attachment Model: thingiverse.com/thing:5098402Vinyl Cutter tool - Silhouette Cameo Kraft Blade: amazon.com/dp/B081K8WS2CIcing Tool - CakeWalk Extruder: lapatisserienumerique.com/en/cakewalk-3d-enDial Indicator - amazon.com/dp/B01G9K7KCKCREALITY Laser Engraving Head Module Blue Violet: amazon.com/dp/B08ZLNMPSWClay Extruder by Wasp - LDM Extruder: https://www.3dwasp.shop/en/product/ceramic-extruder-ldm-wasp-extruder/Super Wavy Vase Model by BritHawkes: cults3d.com/en/3d-model/home/super-wavy-vasePorcelain Clay: amazon.com/dp/B074CKY95FWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinted #3dprinter
How To Install A Simple Laser Engraver on the MUTANT Wham Bam Systems 2021-09-03 | Using the MUTANT you can quickly and easily change your hot-end set up to a laser and turn your 3d printer into a laser engraver and cutter! Here is a complete step-by-step guide to installing a simple laser on your MUTANT including wiring the system, using free software to create gcode, focusing the laser, and creating exciting artwork. whambamsystems.com/mutantTimestamp Index:0:00 Introduction 4:21 Laser Safety 6:00 Mounting the laser7:30 Wiring the laser 8:30 Setting up a build surface with a spoil board 9:20 Focusing the laser 11:30 Setting up the software 14:45 Setting up a document and artwork 22:30 Engraving the artwork Inkscape Software - free download:inkscape.orgJ Tech Photonics Laser Inkscape Extension:jtechphotonics.com/?page_id=1980The written version of the laser install instructions including the table for laser speeds:bit.ly/3DDZJL4MUTANT Technical Support Page:whambamsystems.com/mutant-supportThis PDF contains a list of materials that are safe to laser, a list of dangerous materials not to laser, and shows you how to identify unknown plastics:cpl.org/wp-content/uploads/NEVER-CUT-THESE-MATERIALS.pdfLightburn Software - A great commercial software that is $40-80 a year: lightburnsoftware.comThe Creality laser we used in the video:https://creality3d.shop/products/creality-3d-12v-high-power-laser-engraving-blue-violet-laser-head-module-for-3d-printer-cr-10-cr-10sHere are some of the mixed media projects shown in the video:Coaster with Spoon and Cork - thingiverse.com/thing:4947728Coaster with Foam Empire Logo - thingiverse.com/thing:4948039Please let us know in the comments if you have any laser tips or tricks and let us know what else you might like to see mounted to the MUTANT! Would you be interested in seeing us create an install video using a high-power laser and paid software on the MUTANT? Let us know in the comments!
What Can the MUTANT Do For Your 3D Printer? Wham Bam Systems 2021-07-10 | The MUTANT was created to relieve some of the pains of maintaining your 3D printer and to make it easier for you to swap nozzles and hotends. Once our imaginations took over, we thought of adding tool heads that could change the machine's function! whambamsystems.com/mutantTogether with a handful of very talented beta testers and a few key development partners, we were able to develop many mounts and applications to work with the MUTANT. Check out our growing list of MUTANT downloadables: whambamsystems.com/mutant-supportWe are working with our development partners to bring you mounts for the very best accessories including:Slice EngineeringBondtechWaspCakewalk the MUTANT™ will allow your 3d printer to quickly transform to:-swap out a clogged hotend-use different hotend setups-laser cutter and engraver-pen and marker plotters-CNC mill-food extruders -ceramic and clay extruders -dial gauge indicator -drag knife and vinyl cutter-endless possibilities!Tell us in the comments what attachment you would most like to see on the MUTANT!Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinted #3dprinter #toolchanger
the MUTANT Install Overview Wham Bam Systems 2021-06-14 | A walk-through of the MUTANT install on your 3D printer. The full installation guide, complete list of kit contents, and growing list of downloadable files and guides can be found at whambamsystems.com/mutant-support0:00 Intro0:08 Plan the Wire Harness Cuts0:25 Use the Wire Label Stickers 0:40 Use the Wire Records Card0:50 Cut the Wires and Remove the HotEnd1:05 Mounting Option 1: Add a 3D Printed Interface Plate1:18 Mounting Option 2: Mount a Universal X Gantry Plate1:40 Mount the MUTANT Fixed Plate to the X Gantry1:46 Wire the Machine's Harness to the Fixed Plate2:36 Mount the HotEnd to the Mobile Plate2:54 Wire the HotEnd to the Mobile Plate3:11 Mount the Mobile Plate to Fixed Plate3:16 Time to Create!the MUTANT™ V2 is an innovative new Universal Tool Swapping System that gives you the ability to change your hotend on the fly and allows you to transform your FDM printer into a laser cutter and engraver, pen and marker plotter, food plungers, CNC mill, clay extruder, dial gauge, vinyl cutter, and just about anything you think of! Now available for purchase: whambamsystems.com/mutantWhat will you create?#3dprinting #toolchanger
Introducing the MUTANT™ V2 Wham Bam Systems 2021-06-11 | the MUTANT™ V2 is a Universal Tool Head Swapping System that allows you to transform your 3D printer into so much more! Our design director and CEO Peter walks you through the features, upgrades, and shows a quick example of how easy it is to change between different hotend setups.the MUTANT™ gives you the ability to change your hotend on the fly and easily add other tools such as laser cutter and engraver, pen and marker plotter, food plungers, CNC mill, clay and ceramics extruder, dial gauge, vinyl cutter, drag knife, and just about anything you think of, all driven by the machine’s mechatronic components! Now available for purchase: whambamsystems.com/mutantWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinting #toolchanger
Transform Your 3D Printer with the MUTANT V2 Wham Bam Systems 2021-06-08 | the MUTANT™ V2 is an innovative new Universal Tool Swapping System that allows you to transform your FDM printer into so much more! the MUTANT™ gives you the ability to change your hotend on the fly and easily add other tools such as laser cutters, pen plotters, CNC mill, food plungers, ceramic printers, dial gauges, vinyl cutter, and just about anything you think of, all driven by the machine’s mechatronic components! the MUTANT™ V2 is now available to purchase, learn more here: whambamsystems.com/mutantSee the entire MUTANT product line here: whambam3d.com/collections/mutantSee all the downloadable files here: whambamsystems.com/mutant-supportthe MUTANT V2 allows you:-Easy maintenance of hot end on your workbench-Quick swap if you have a clog or problem-Swap with other hot ends for different jobs: for example; a 0.4 nozzle for regular work and a 1.0 with volcano heater for big prints, and a 0.2 for fine work, swap with different hot ends for performance such as an all-metal or high temp hot end.-Swap with other tools to convert your printer: Laser engraver, CNC mill, Pen Plotter, Cake and Food Printer, Ceramic Printer, vinyl cutter, etc.Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinting #toolchanger #3dprinter
The Black Knight - Print and Paint Wham Bam Systems 2021-05-22 | A quick demonstration of a print removal, cleaning, and painting of this fun model of the Black Knight by Highlands Miniatures that fits magnets allowing you to enact the battle of the Black knight as he looses limbs:myminifactory.com/object/3d-print-black-knight-from-monty-python-highlands-miniatures-167182Printed on the Phrozen Sonic Mini 4k with Elegoo ABS Like translucent resin and some added Monocure pigments. Quick and easy print removal by the Wham Bam Flexible Build System for Resin: whambamsystems.com/fbs-for-resinPaints used:Golden Fluid Acrylic Paint 1 Ounce-Iridescent Gold Deepamazon.com/dp/B0027A77BQSilver (Fine)amazon.com/dp/B01LW5GORMLet us know in the comments if you have printed this model or if you plan to!Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinted #resin #MontyPython
Fun Moai Lamp From A 3D Print Wham Bam Systems 2021-05-01 | This fun mood lamp is a project our design director Peter did recently for his kids and once you see how well it turned out it may inspire some of you to print some large models and light them up!The Moai was printed in Solutech PLA hollow and with a few walls on the Wham Bam Flexible Build System. You can find the STL here: Moai statue - No overhang by Julien_DaCosta thingiverse.com/thing:2493386If you have another lighting solution please do share in the comments! After testing a few USB LED light systems, this is the one Peter went with: amazon.com/dp/B077N4VNH7Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinted #3dprinting
Efficient Cleaning of Your Resin Prints Wham Bam Systems 2021-04-09 | Here is an easy and effective cleaning process for resin prints that will prevent them from staying sticky, losing detail, or having ugly streaking and hazing even on transparent prints. After experimenting with 2 different cleaning setups and trying various cleaning solvents including MeanGreen, Peter has come back full circle to using only IPA and a few simple steps.If you are interested in the straining vat that Peter designed and shows in the video, you can find it here: thingiverse.com/thing:4570079We hope you find this helpful, please let us know in the comments if you have any questions or let us know your cleaning process!Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851tiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems#3dprinting #resinprinting
Installation of the Flexible Build System for Resin (Updated) Wham Bam Systems 2021-03-16 | This is a complete step-by-step printer installation for the Wham Bam Flexible Build System for Resin. This install video is full of important tips and insights, here is an index if you would like to jump around to different sections:0:00 Introduction0:21 Modifying Z Limit Height03:53 Preparing Your Build Plate to Install Magnet11:58 Installing Magnet15:46 Leveling your Build Plate24:29 Printing Solutions29:44 Magnetic Forces and Part Orientation32:27 Cleaning Your Build Plate Between PrintsOur FBSR support page with more info and links to Z Limit Spacers: whambamsystems.com/fbs-for-resin-supportIf you need any further product support please reach out to our technical support at technical@whambamsystems.comWe hope you find this helpful, please let us know in the comments if you have any questions or feedback!Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851youtube.com/whambamsystemstiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Simple Silicone Mold Tutorial Using A 3D Print Wham Bam Systems 2021-03-08 | Basic tutorial for beginners on how to make a silicone mold using a 3d print. Use your 3D printing skills to make molds then pour in the material of your choice; clear resins, flexible polyurethanes, rigid materials, foaming materials, even cement as shown here.BACOENG 3 Gallon Vacuum Chamber Kit with 3.6 CFM 1 Stage Vacuum Pump HVAC by BacoFlo:amazon.com/dp/B00W8ZU5FKIf you found this helpful give us a thumbs up and if you would like to see more advanced techniques let us know in the comments!Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851youtube.com/whambamsystemstiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Installation of the Wham Bam Flexible Build System (Updated) Wham Bam Systems 2021-02-22 | This is a complete install installation for the Wham Bam Flexible Build System, shown here on a CR-10 V3, although it is a similar process for most machines.In this video we mount the Magnetic Base directly to the heated bed, if you would like to mount to a separate build surface such as glass or aluminum and use bed clips to keep it in place, you can refer to this video: youtu.be/PNCam4_wp1gWe also show the preparation of our Pre-Installed Flexi Plate with PEX, if you would like to see how to install PEX on a Flexi Plate watch this video: youtu.be/FxP8f6jVnQcOur bed leveling G-codes can be found here: thingiverse.com/thing:4761680For a more detailed video on bed leveling and getting a great first layer: youtu.be/8VgVwCeaovQThis video is full of important tips and insights, here is an index if you would like to jump around to different sections:0:00 Introduction00:32 Install on Build Surface or Heated Bed01:12 Verifying Build Surface Flatness04:22 Accounting for Change in Z Height 16:30 Cleaning and Preparing your Heated Bed22:25 How to Measure your Heated Bed for the Right Kit23:00 Installing Magnetic Base to Heated Bed27:00 Preparing your PEX or Build Surface31:03 Verifying home after the install33:20 Bed Leveling40:00 First PrintWe hope you find this helpful, and if so, please do let us know in the comments!Where to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851youtube.com/whambamsystemstiktok.com/@whambamsystemsreddit.com/user/WhamBamSystems
Introducing the MUTANT! Wham Bam Systems 2021-01-11 | *** the MUTANT™ V2 is now available! Learn more: youtube.com/watch?v=6pSx-t60gDYthe MUTANT™ is an innovative new Universal Tool Swapping System that will give your FDM printer the ability to change your hot end on the fly, mount various hot ends, and use other tools such as laser cutters, pen plotters, food plungers, ceramic printers, dial gauges, and just about anything you think of can be driven by the machine’s mechatronic components!See the entire MUTANT product line here: whambam3d.com/collections/mutantSee all the downloadable files here: whambamsystems.com/mutant-supportMUTANT allows you to:-Easy maintenance of hot end on your workbench-Quick swap if you have a clog or problem-Swap with other hot ends for different jobs: for example; a 0.4 nozzle for regular work and a 1.0 with volcano heater for big prints, and a 0.2 for fine work, swap with different hot ends for performance such as an all-metal or high temp hot end.-Swap with other tools to convert your printer: Laser engraver, CNC mill, Pen Plotter, Cake and Food Printer, Ceramic Printer, vinyl cutter, etc.#3dprinter
Bonding PLA parts using adhesives and welding Wham Bam Systems 2020-09-19 | In this video, Peter will cover various methods to bond PLA including adhesives and chemical welding. Please be careful with solvents!! Use face masks, use in well-ventilated areas, use gloves and eye protection, and read product instructions on how to stay safe while using! If you have any questions or have some tricks of your own, please let us know in the comments.3D Gloop: 3dgloop.comDichloromethane DCM: amazon.com/dp/B07947WFVJCA: amazon.com/dp/B001NI4JWIAccelerant: amazon.com/dp/B0166FFCCSBaking soda: your neighborhood grocery store!Tutorial on adhesives: youtu.be/5XCJauPrlKYGluing flexible filaments: youtu.be/Oqh01j7ZG_sABS vapor smoothing: youtu.be/d386HlCz8SQWhere to find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#3dprinting #BondPLA
HotBox V2 - New Features Added! Wham Bam Systems 2020-08-17 | The Wham Bam HotBox has a new and improved version 2 (or V2) and the following new features have been added to our lightweight, foldable 3d printer enclosure:- An additional filament passage in the center of the top panel for direct drive printers- 2 sets of loops to hold a LED light bar- All of the access holes are now sewn along the seemswhambam3d.com/products/hotbox-3d-printer-enclosureIf you want to print ABS, Nylon, PC, and other high-temperature filaments, an enclosure is one of the best upgrades for your machine. The Wham Bam HotBox is your easy to assemble and store solution! Designed to fit many small 3D printers with enough room for a desk mounted spool holder or tool holder alongside your machine. The internal measurements are 568mm x 568mm x 484mm, 21.2" x 21.2" x 19" and has already been confirmed to fit:Ender 3Ender 3 ProEnder 2Prusa MK2Prusa MK3Prusa MiniAnycubic i3 MegaSnapmaker A150CR-10 mini (using printable foot extender)See the HotBox in action, check out our HotBox YouTube PlaylistThe HotBox is made of high-grade Nylon 600D fabric with fire-resistant coating and lined with a metallic heat deflecting internal liner that sandwiches around a strong, lightweight honeycomb insulating structure.The front panel has a large clear window for maximum visibility and easily lifts up for full access to your printer. There is a velcro retaining strip on top to keep the panel open while working.The top panel has an access door for spool holder passage and for the vacuum tube, and a built-in thermometer.Features include:-Lightweight semi-rigid construction-Excellent insulating properties-3 cable exits, one each on the left, right and back panels-A large, transparent front window-Large opening for front access-Door for pass through top-mounted spool holder-9 metal lined filament passage holes, 5 on the back panel, 2 on the top panel, and one each on the left and right panels-9 plugs to fill filament holes when not in use-Built-in thermometer-Passage with cover for user-added aspiration and air filtering-Folds up flat, easy to store and transport-2 sets of loops to hold a LED light bar
Installing the FBS for Resin on the Epax X1 Wham Bam Systems 2020-08-11 | Wham Bam Systems has done it again! The creators of the original Flexible Build System have designed a new line of FBS for resin printers!This video shows you how is easy it is to install and use it on Epax X1. Just clean your build plate very well, let dry, bond your magnet to the plate, reset your Z limit to account for the additional 2.6 mm, and you are ready to start printing!Available for pre-order in 8 sizes and taking requests for more:whambamsystems.com/fbs-for-resinZ-limit spacer : thingiverse.com/thing:4565824
Installing the FBS for Resin on the Elegoo Mars Wham Bam Systems 2020-08-11 | Wham Bam Systems has done it again! The creators of the original Flexible Build System have designed a new line of custom FBS for resin printers!This video shows you how is easy it is to install and use it on the Elegoo Mars. Just clean your build plate very well, let dry, bond your magnet to the plate, reset your Z limit to account for the additional 2.6 mm, and you are ready to start printing!The Elegoo Mars system and 7 other sizes are available now for pre-order and we are taking requests for more:whambamsystems.com/fbs-for-resinspacer file here: thingiverse.com/thing:4533310
254x220 vs 254x235 Build Surfaces Wham Bam Systems 2020-07-15 | Here is an explanation of the difference between a 254x220 build surface or a 254x235 build surface on a 254x235 Flexi Plate for a Prusa Mk3. We are no longer going to carry the 254x220 size and have marked them down to sell out of our existing inventory, find the links below.PC - whambam3d.com/products/build-surfaces-254-x-220?variant=32018761384034PEI - whambam3d.com/products/build-surfaces-254-x-220?variant=32018761416802PEX - whambam3d.com/products/build-surfaces-254-x-220
BTS at the Wham Bam Laboratory | Our 3D Printers and Workshop Space Wham Bam Systems 2020-03-09 | Behind the scenes glimpse of our laboratory, excuse the mess no prep was done for this brief tour. Wham Bam Systems was created by people passionate about 3D printing and improving on current technologies. We print every day of the week, nearly every hour, out of love for 3d printing and to put our products to the test!If anyone would like more info on anything in our workshop, our machines, processes or even just general advice please comment and we will do our best to reply! Is there another video you would like to see us make? Let us know in the comments!Follow us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#3dprinting #bts
HotBox Build and New Features! Wham Bam Systems 2020-01-05 | The Wham Bam HotBox enclosures are in stock and this production unit HotBox has some new features we would like to show you! Watch as it only takes seconds to set up, then learn about the construction and features of this amazing 3d printer enclosure.whambam3d.com/products/hotbox-3d-printer-enclosureThe HotBox is made of high-grade Nylon 600D fabric with fire-resistant coating and lined with a metallic heat deflecting internal liner that sandwiches around a strong, lightweight honeycomb insulating structure. Designed to fit the Ender 3, Ender 3 Pro, Ender 2, Prusa MK2, Prusa MK3. Internal measurement - 568mm x 568mm x 484mm, 21.2" x 21.2" x 19"Printable HotBox upgrades collection: thingiverse.com/psdesign/collections/hotboxFeatures include:-Lightweight semi-rigid construction-Excellent insulating properties-3 cable exits, one each on the left, right and back panels-A large, transparent front window-Large opening for front access-Door for pass through top-mounted spool holder-8 metal lined filament passage holes, 5 on the back panel and one each on the left, right & top panels-Built-in thermometer-Passage with cover for user-added aspiration and air filtering-Folds up flat, easy to store and transportWe are working on designs for the next HotBox, capable of holding larger printers. Help us with measurements of your printer by filling out this form and we will give you an exclusive pre-sale discount for your help! http://eepurl.com/gNKQB9Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#3dprinting
Flexi-Facehugger Model Customization Wham Bam Systems 2019-12-28 | A simple way of customizing this Flexi Facehugger 3d model by OneldMONstr thingiverse.com/thing:3776361Printed in AMZ3D black PLA with the easy stick and release of a Wham Bam Flexible Build System. Watch as Peter drills a hole in the print and embeds a neodymium magnet, then finishes it by brushing with silver acrylic.Give us a thumbs up if you like this video and found it useful. Please leave us any questions in the comments.Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#3dprint #3dmodel #alien
Installing a Wham Bam Magnetic Base to Your 3D Printer Bed Wham Bam Systems 2019-12-26 | When installing a Wham Bam Magnetic Base to your 3D printer you want to mount it to the flattest bed surface possible. If your heated aluminum bed and it's flat, this may be the best option for you. If you need to mount to a glass bed, this video shows how to do that as well.Please after installing the magnet WAIT 24-72 HOURS FOR 3M TO CURE BEFORE USE!Here is a link to thermally conductive silicone pads, you will need 2 of these:amazon.com/gp/product/B007PPEW52/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851
Sexy First Layers in ABS Using the HotBox and FBS Wham Bam Systems 2019-11-30 | Quick video of some perfect first layers in ABS filament using the Wham Bam HotBox and Flexible Build System. This combo makes printing ABS and other high-temperature filaments a breeze!The Wham Bam HotBox is a lightweight, quick to install 3d printing enclosure that makes printing with high temp filaments fun, easy and productive! Learn more: whambamsystems.com/hotboxThe Flexible Build System is a high-temperature flexible bed system resisting bed temps of up to 150 degrees continuously! Learn more: whambamsystems.com/flexible-build-systemGive us a thumbs up if you enjoyed this video. Please leave us any questions in the comments.Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#enclosure #3dprinting
Easy ABS Printing in 4 Steps Using the HotBox Wham Bam Systems 2019-11-19 | Printing ABS filament can be simple with the right settings and equipment.1) Dry your ABS filament before using it. To see detailed suggestions on DIY filament drying ideas, check out this video from Peter: youtube.com/watch?v=r8nNoDIp-Is&t=16s2) You will need an enclosure or you will get layer separation and failed prints. The Wham Bam HotBox is a great upgrade to get right into printing ABS and other high temp filaments: whambam3d.com/products/hotbox-3d-printer-enclosure3) Make sure to level the machine once it's heated to printing the temperature. Here are some tips and gcode for easy leveling on an Ender 3: youtube.com/watch?v=RJC7N4Vb9AY&t=19s4) Use a bed between 100-120°C and a hot end at 240-250°C. Do not use your part fan till 3 or 4th layer and keep it at a lower flow than for other materials to help layer bond. Depending on your room temperature you can find the right bed temp between 100-120 to keep your HotBox at the perfect 40-50 range. If you don't have a surface that has great adhesion you may want to use some Magigoo or glue stick to keep your first layer down.You need to also print on a build surface that can take the heat of the bed and the filament. If using a flexible magnetic system, magnets should be able to take the higher heats without failing. Common PC beds are not recommended as the High Temp of ABS tends to fuse to them. We are using the Wham Bam Flexible Build System with a PEX build surface which is guaranteed to 150°C constant temperature. Learn more about our FBS and see available machine fits: whambamsystems.com/flexible-build-systemGive us a thumbs up if you like this video and found it useful. Please leave us any questions in the comments.Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#3dprinting #enclosure
Heat up Time in the HotBox Wham Bam Systems 2019-11-14 | In this video, we demonstrate how fast the HotBox enclosure can heat up using only the heated bed of the Ender 3 Pro. We go from room temp to 40°C in less than 20 minutes.This model of the HotBox was designed for the Ender 3, 3 Pro, clones and any smaller machines including Prusa MK2/MK3: whambam3d.com/products/hotbox-3d-printer-enclosureMore information on machine fits will be published as we have developments and testing data. In the future, we will be making a variety of sizes for different machines in the future and offering accessories too.Watch how quick and easy the HotBox is to set up and install: youtu.be/XJPWDQN4XOQFeature Overview for the HotBox: youtu.be/aLEIGV8ivGcGive us a thumbs up if you like this video and found it useful. Please leave us any questions in the comments.Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#Ender3 #Enclosure
Feature Overview for the HotBox Enclosure for 3D Printers Wham Bam Systems 2019-11-13 | **New version with updated feature list: youtu.be/-g5dV_LFVPIHere is an overview of our newest product the HotBox 3d printing enclosure designed for the Ender 2, 3, 3 Pro, Prusa Mk2 & Mk3 and their clones as well as any smaller machines with enough room for a desk mounted spool holder or tool holder alongside your machine. More information on machine fits will be published as we have developments and testing data. We will be making a variety of sizes for different machines in the future and offering accessories for the HotBox too!If you want to print ABS, Nylon, PC and other high-temperature filaments, an enclosure is one of the best upgrades for your machine. The HotBox is made of high-grade Nylon 600D fabric with fire-resistant coating and lined with a metallic heat deflecting internal liner that sandwiches around a strong, lightweight honeycomb insulating structure.The front panel has a large clear window for maximum visibility and easily lifts up for full access to your printer. There is a velcro retaining strip on top to keep the panel open while working. The top panel has an access door for spool holder passage and for the vacuum tube, and a built-in thermometer.Features include:-Lightweight semi-rigid construction-Excellent insulating properties-Cable exit on the lower back panel-A large, transparent front window-Large opening for front access-Door for pass through top-mounted spool holder-8 metal lined filament passage holes, one on each of the top, left and right panels-Built-in thermometer-Passage with cover for user-added aspiration and air filtering-Folds up flat, easy to store and transport. Product size: 580mm wide x 580mm deep x 490mm tall, 22.8” wide x 22.8” deep x 19.3” tallProduct weight: 3.1 kg, 6.8 lbsDownload the tabletop spool holder: thingiverse.com/thing:3490081
Quick Assembly and Install of HotBox Wham Bam Systems 2019-11-08 | The setup and installation of the new Wham Bam HotBox is quick and easy. Unfold the sides and position the top and front into place. Then zip each side closed and that's it, your 3d printer enclosure is built!To install on the Ender 3, remove your horizontal tube from the filament holder, open the top central flap on the HotBox and lift the HotBox and slide it over the Ender 3. Reattach your filament to the holder or add your filament right alongside your printer inside the HotBox. The only thing left to do is pass your cables through the back hole and you are ready to print!Now available for Pre-Order at the lowest price of the year: whambam3d.com/products/hotbox-3d-printer-enclosureFeatures include:-Lightweight semi-rigid construction-Excellent insulating properties-Cable exit on the lower back panel-A large, transparent front window-Large opening for front access-Door for pass through top-mounted spool holder-8 metal lined filament passage holes, 5 on the back panel and one each on the left, right and top-Built-in thermometer-Passage with cover for user-added aspiration and air filtering-Folds up flat, easy to store and transport#enclosure #Ender3
Zombie Head Timelapse - Print, Paint & Glue Wham Bam Systems 2019-10-30 | Here is a quick video on Wham Bam's 2019 Halloween project featuring this zombie head model by Wekster: myminifactory.com/object/3d-print-zombie-head-102395This was printed on the Epax1 using Elegoo Transparent Resin with a bit of zombie green coloring. Painted Dollar Tree tea lights and epoxied underneath the prints. Wham Bam Slap Mats used under resin printers, for print cleanup, model painting and gluing.The Slap Mat helps to make the toxic gooey clean up of resin printing easier. Plus it doubles as a craft mat, protecting your work surface from chemicals, glues, solder, and more! See all the benefits of the Slap Mat in this video: youtu.be/KizrcL5YaKQPre-Order now and save $4 on a single Slap Mat: whambam3d.com/products/slap-matOr save $17 on a 3 pack: whambam3d.com/products/pre-sale-slap-mat-3-packHappy Halloween!#resinprint #halloween #project
Introducing the Slap Mat for Resin Printing and More! Wham Bam Systems 2019-10-23 | The Wham Bam Slap Mat made of pure first-grade silicone and will not be harmed by printer resins, most chemicals, or most glues! Stop working with resin on cardboard and paper towels, throwing away a toxic gooey mess after every clean-up or resin transfer. Use Slap Mat to protect your work surface, spill and splash all you like and when you are done, take it outside. The resin will harden, and with a simple flex, it pops right off to be safely and easily disposed of. Use under each of your resin printers as a catch-all.Slap Mat is also great as a general silicone craft mat, protecting your work surface from glue, body putty, painting, even resisting melted solder and the tip of most soldering irons for up to 3 minutes.Order yours here: whambam3d.com/products/slap-matSize: 240 mm x 500 mm (9.5 in x 19.7 in)Give us a thumbs up if you like this video and found it useful. Please leave us any questions in the comments.Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#resinprinting #resinprinter
Installation Instructions for Round 310 and 220 Diameter Build Surfaces Wham Bam Systems 2019-06-20 | Here are our instructions for installing Wham Bam round build surfaces for the Ø310 and Ø220 kits. You can find our 3d files for the alignment guides here:thingiverse.com/thing:3659278Both the Ø310 and Ø220 kits have notches around the outside to leave room for the clamps, as the machines they mount on do not have easy access to the underside of clamps, this makes it easier to set up the machine.You must work in a clean area, take your time peeling 3M backing paper so it doesn't tear around notches. Hope this helps!Please leave a comment if you have any questions or suggestions. If this video was helpful please like and subscribe!http://www.whambamsystems.com
Easy Method of Vapor Smoothing ABS Wham Bam Systems 2019-05-03 | Vapor smoothing is relatively easy and works well with ABS using acetone.* ABS gives off toxic fumes when printing, acetone is dangerous to breath, and flammable, so use in a well ventilated area, wear gloves and a respirator mask, keep the acetone away from a fire or heat source, use basic good sense!*This only works on ABS with Acetone, there are other solvents for other filaments, but you start to get into controlled substances.Polymaker makes a proprietary filament that smooths with IPA alcohol and is less harmful, a bit more expensive, they even make their own vapor smoothing chamber. I have yet to try it out, but would love to!us.polymaker.com/product/polysmoothSee my previous post on printing ABS here: youtube.com/watch?v=85kuZFygFV0Let me know if this was helpful and if you have any tips or tricks to add to this in the comments!
The Capture and Release of the Elusive Octopus Wham Bam Systems 2019-05-01 | See how well the Octopus (thingiverse.com/thing:3495390) prints and sticks to the Wham Bam Flexible Build System, and watch till the end to see how hard it is to remove it from the bed!Printed on an Ender 3 Pro, with AMZ3D PLA at 0.20 layers, 80mm/s print speed. Bed temp 70°, hot end 205°, first layer slow (25% speed) and squished down well, enough for material to come out but nice and flat-topped all around, clean surface, no bed fan until 3rd layer.Give us a thumbs up if you like this video and found it useful. Please leave us any questions in the comments.Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851
Easy Print Surface Installation Wham Bam Systems 2019-05-01 | I will demonstrate how to install your print surface to your build surface with a few easy steps.In this video I am showing the installation of the Wham Bam flexible build system, you will see how to install the PEX build surface onto our Flexi Plate, although you can use the same method for PEI, PC or other build surfaces.Work in a very clean area, dust particles and dirt are your enemy.Our PEX is super transparent so you will see some hazing in the 3M glue, this is natural and can't be avoided but does not affect the performance or longevity.Make sure you work from center outward with a precise strategy.I am showing the dry method, I have taken down the wet method videos as some users had issues with trapped liquid under the surface. If any of you have extensive experience with applying decals and adhesives with soapy water or windex and can share your knowledge how to avoid trapped liquid please share, I would be happy to test your methods and share results.Let me know in the comments if this helps!www.whambamsystems.com for more info on our products@whambamsystems
Successfully Print ABS on your 3D printer! Wham Bam Systems 2019-04-22 | ABS is a wonderful material to print with as it is robust, cleans up nicely, is temperature resistant and can be vapor smoothed. But to print ABS you are going to need to modify your machine to reach the right temperatures and you will need an enclosure. Here you will see two enclosures, one which we welded and build to spec, the other was a simple box you can make on your own. We also show you the most critical factors in getting a successful print.Our lightweight, easy to setup 3d printer enclosure solution ... The HotBox:whambam3d.com/products/hotbox-3d-printer-enclosureVapor Smoothing instructions here: youtube.com/watch?v=d386HlCz8SQ&feature=youtu.beFilament drying solutions: youtube.com/watch?v=r8nNoDIp-Is&t=202s Attention: ABS does give off toxic fumes while melting so use in a well-vented room or you might begin to experience symptomsIf you have any other tips please put them in the comments for other viewers. If this was helpful please give us a thumbs up!Find us online:https://www.WhamBamSystems.comfacebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851
How to assemble a Wham Bam Maker Coin Wham Bam Systems 2019-03-26 | This is an assembly video for the Wham Bam Maker Coin.You can download the files from thingiverse at: thingiverse.com/thing:3519267and print yourself.Or if you meet us at one of the Maker Faires you may be able to get your hands on one of our fun maker coins! We made it to have multi color options, and a nice neck and back massager feature.Wham Bam will also be running some contests to win them so subscribe to our page and follow us on social media and facebook!I particularly like how it easily prints with no supports, and assembles with ease, once assembled it locks in place, and massager ring moves easily!.Hope you like it.
Put your unwanted publicity mailers to good use mixing epoxy and body putty! Wham Bam Systems 2019-03-12 | I used to hate receiving unwanted catalogues, credit cards, store cards, etc, you can't refuse them so they would just go into the trash!Now I look forward to receiving them.They make for great tools to mix epoxy and body filler! See this video for proper mixing technique.hope you enjoy this short vid!
Easy Perfect Bed Leveling on the Ender 2 Wham Bam Systems 2019-02-14 | Here are my tips for best practice in leveling your bed. It is of utmost importance that your bed is level and the correct gap is set correctly for every print. Once you learn the process its easy and fast and may not have to do more than simple on-the-fly adjustments while your printer is laying down the skirt for most of the time thereafter.You will need a function of the printer which runs around the bed and stops the nozzle right above each leveling knob for a few seconds before moving on, or a gcode which does the same that you can use via print function.You will need to have your home set correctly. To do this compress all springs on your bed to half way (do this evenly and slowly one at a time just a bit at a time as to not bend your bed).Once your springs are evenly compressed half way home your machine through the control panel. Your nozzle should just touch the print surface. If it doesn't, adjust your Z limit switch up or down until it homes at correct position.Having your springs well compressed will give you more stable push back from the springs and it will hold your level much longer.Now heat your machine to desired print temp (both nozzle and heated bed).Once heated, run your leveling program or gcode. Do not push your hot end and bed around, this may create movement on the Z and give you false readings.Put a strip of copy paper ( I like the heavier type - about 28 lb. stock) under the nozzle as it stops at each point and if there is no drag, move your leveling knob at that point until it creates drag. Try to slide the paper back and forth with a grip about 3" or 60 mm from the nozzle, you should feel drag on the paper. If you cannot pull or push the paper under the nozzle back off your bed until it passes. Try not to turn any single knob more than one turn or it may bend your bed, you may have to adjust each of the knobs together for first round.Allow it to move to the next corner. Repeat the above for all corners.Repeat the process again, you will notice that when you move one corner it can have an affect on the others.Repeat the process until you go all the way around all bed leveling knobs without adjusting at all.Thats it your bed is level.Now to set the gap.Program your slicer to print about 2-3 skirt lines as far away from the part so it goes close to the edge of your printer.Set your part to print, and while its laying down your skirt lines, inspect visually and adjust your knobs closest to print areas as necessary.If the bead laid onto the bed is too round and high, close the gap slightly.If it is flat topped and a bit wider than the nozzle width it is perfect.If it is too transparent and doesn't flow out, your gap is too tight, you need to increase the distance slightly.For more information on getting the perfect first layer please see: cults3d.com/en/blog/articles/6-main-factors-for-perfect-first-layer-3d-printingand cults3d.com/en/blog/articles/how-to-level-3d-printing-bedYou can do this for every print.Please see the full explanation on tricks to getting a great first layer here if you haven't seen already.youtu.be/8VgVwCeaovQdownload my gcode, and copy to your SD card and run as a print: dropbox.com/s/s6anxy86a88k0vj/Ender2LEVELpsd.gcode?dl=0I hope this helps!Please let me know in the comments.
Best Ender 2 Mods! Wham Bam Systems 2019-02-12 | *please note, the Ender2 prints great out of the box! You don't need mods to print PLA and simple hobby printing. Mods are a fun way of learning about your machine as well as adding performance.One word of advice; add a single modification at a time, print and test, see if it made your machine better or worse, see if it did what you set out to do with the mod before moving on to the next.*1. Extruder: I mount the SeeMeeCNC EZstruder on all my machines, it constrains filament path very well so you can print flexible with no problem, is easy to load, and requires no flashing of firmware or difficulty in mounting.seemecnc.com/products/ezrstruder2. Bed Springs: follow my instructions here to mount better quality bed springs and to block the screw, this will give you a more stable bed with less vibrations!youtube.com/watch?v=-UL1d61HClo&t=111ssprings affiliate link: amzn.to/2WNTzCP3. Insulate Bed:I like to insulate the underside of the bed so it heats faster and contains the heat as well as keeping the heat more consistent across the full bed.here is a pretty good video: youtube.com/watch?v=XBiIrSnM2NwI use insulation tape affiliate link: amzn.to/2SFfoFDand metallic tape affiliate link: amzn.to/2tdIsoY4. Wham Bam flexible Build Surfacewhen you are looking for the best solution to getting your prints to stick to your build surface and then being able to remove them effortlessly get the best- i developed this- Wham Bam flexible build system. You will need the 165 kit. The magnets were made to resist up to 130°C constant use so you can practically print any material! The PEX surface even surpasses the industry standard PEI for temperature resistance. wham-bam-systems.myshopify.com/collections/165mm5. Extruder Knob: easy print and mod. this lets you see the movement of the extruder, manually feed or retract filament, and it has only 3 arms allowing for better visibility of the extruder gears.thingiverse.com/thing:27997936. LED light bar: I can't live without this, easy print bar that mounts to the rear of your X gantry and puts light right where you need it. Wiring diagrams in thingiverse file.thingiverse.com/thing:2700450LED strips 12V for Ender 2 affiliate link : amzn.to/2DXHhQWcan be used with this switch and housing or with next line item:thingiverse.com/thing:3315172simple round Rocker Switch affiliate link: amzn.to/2CzkYQG7. Power Supply Cover with Shut off Switch:thingiverse.com/thing:27151228. Control Panel Housing with SD Full size SD card reader housing and light switch: I hate dealing with mini SD cards and trying to get them into the slot!thingiverse.com/thing:2706488SD card Converter affiliate link: amzn.to/2HXf14N9. Fan ducts with blower 5015 fan: I like the design sensibility of this model, its easy to mount, and works very wellthingiverse.com/thing:317989212V blower fan affiliate link: amzn.to/2SsaQlR10. Electrical connectors on all hot end components. On the first change of hot end parts or upon mounting your new fans, add connectors to every electrical lead to make changes and maintenance easy from then onward. Just connectors on low amp connections: fans, thermistor. XT30 on the heater cartridge. Heater Cartridge and thermistor have no polarity so dont worry about color of leads. fans all have polarity so match red to red and black to black.XT30 connectors for heater cartridge affiliate link: amzn.to/2MRVdPbJST connectors for fans and thermistor affiliate link: amzn.to/2MSljS311. Filament Cleaner: keep your filament clean with this simple print in place holderthingiverse.com/thing:272340312. Spool holder washer: I hate when spools have a huge inner hole and can slip off over the nut, use this to hold any spool in placethingiverse.com/thing:2665114forgot to mention in the video:13. Heated Bed Cable Strain Relief:thingiverse.com/thing:270643614. inside the hotted I am using Luke Hatfield's hot end fix, works like a charm!thingiverse.com/thing:320432615. sorbothane feet:thingiverse.com/thing:2723395*please excuse my affiliate links, if I am going to take all the time to spec parts I hope Amazon appreciates my referrals, and you pay no more.*
My preferred mods for the Ender3! Wham Bam Systems 2019-02-07 | Here is a full video and list of my preferred mods for the Ender3!*please note, the Ender3 prints great out of the box! You don't need mods to print PLA and simple hobby printing. Mods are a fun way of learning about your machine as well as adding performance.One word of advice; add a single modification at a time, print and test, see if it made your machine better or worse, see if it did what you set out to do with the mod before moving on to the next.*1. Extruder: I mount the SeeMeeCNC EZstruder on all my machines, it constrains filament path very well so you can print flexible with no problem, is easy to load, and requires no flashing of firmware or difficulty in mounting.seemecnc.com/products/ezrstruder2. Bed Springs: follow my instructions here to mount better quality bed springs and to block the screw, this will give you a more stable bed with less vibrations!youtube.com/watch?v=-UL1d61HClo&t=111ssprings affiliate link: amzn.to/2WNTzCP3. Insulate Bed:I like to insulate the underside of the bed so it heats faster and contains the heat as well as keeping the heat more consistent across the full bed.here is a pretty good video: youtube.com/watch?v=XBiIrSnM2NwI use insulation tape affiliate link: amzn.to/2SFfoFDand metallic tape affiliate link: amzn.to/2tdIsoY4. Wham Bam flexible Build Surfacewhen you are looking for the best solution to getting your prints to stick to your build surface and then being able to remove them effortlessly get the best- i developed this- Wham Bam flexible build system. You will need the 235 kit. The magnets were made to resist up to 130°C constant use so you can practically print any material! The PEX surface even surpasses the industry standard PEI for temperature resistance. wham-bam-systems.myshopify.com/collections/flexible-build-system/products/flexible-build-system-235-x-2355. Extruder Knob: easy print and mod. this lets you see the movement of the extruder, manually feed or retract filament, and it has only 3 arms allowing for better visibility of the extruder gears.thingiverse.com/thing:27997936. LED light bar: I can't live without this, easy print bar that mounts to the rear of your X gantry and puts light right where you need it. Wiring diagrams in thingiverse file.thingiverse.com/thing:3292889LED strips 24V for Ender 3 Pro affiliate link : amzn.to/2tboriXLED strips 12V for Ender 3 affiliate link : amzn.to/2DXHhQWcan be used with this switch and housing or with next line item:thingiverse.com/thing:3315172simple round Rocker Switch affiliate link: amzn.to/2CzkYQG7. Full size SD card reader housing and light switch: I hate dealing with mini SD cards and trying to get them into the slot!Use this to mount a full size SD card reader, stop stressing your PC board and reader connection, and it houses the light switch for the LED bar, and has a SD card holder for extra cards!thingiverse.com/thing:3292867or use this handy SD card converter holder: thingiverse.com/thing:3255028SD card Converter affiliate link: amzn.to/2HXf14N8. Fan ducts with blower 5015 fan: I like the design sensibility of this model, its easy to mount, and works very wellthingiverse.com/thing:317989224V blower fan for Ender 3 Pro affiliate link: amzn.to/2HXf14N12V blower fan for Ender 3 affiliate link: amzn.to/2SsaQlR9. Electrical connectors on all hot end components. On the first change of hot end parts or upon mounting your new fans, add connectors to every electrical lead to make changes and maintenance easy from then onward. Just connectors on low amp connections: fans, thermistor. XT30 on the heater cartridge. Heater Cartridge and thermistor have no polarity so dont worry about color of leads. fans all have polarity so match red to red and black to black.XT30 connectors for heater cartridge affiliate link: amzn.to/2MRVdPbJST connectors for fans and thermistor affiliate link: amzn.to/2MSljS310. Filament Cleaner: keep your filament clean with this simple print in place holderthingiverse.com/thing:272340311. Spool holder washer: I hate when spools have a huge inner hole and can slip off over the nut, use this to hold any spool in placethingiverse.com/thing:266511412 . Filament guide: this is a nice simple print to keep your filament path more aligned with extruder openingthingiverse.com/thing:2917932*please excuse my affiliate links, if I am going to take all the time to spec parts I hope Amazon appreciates my referrals, and you pay no more.*Please let me know if this help and if anyone wants to see a video of my final set up!
How well does PETG adhere and release from Wham Bam flexible build surface? Wham Bam Systems 2019-02-05 | quick video showing multiple part builds in PETG with minimal foot print and no brim, each part stuck really well even with high speed and zigzag infill vibrations! And the release is the most fun!see for yourself!www.whambamsystems.com
Refurbishing your Wham Bam PEX Build Surface Wham Bam Systems 2019-02-04 | This video walks you through the steps to refurbish your PEX surface to get adhesion back to the way it was when it was new! It's a simple process just have the following items on hand for this and for periodic cleaning:-Acetone (pure hardware store variety- not nail polish remover)-Isopropyl alcohol (91% or higher from drug store)-Clean paper towel-000 Steel wool-Goggles and rubber glovesJust scrub lightly with steel wool and a bit of acetone, being careful not to get the acetone under the PEX sheet and onto the 3M tape.Clean with a paper towel.Add some isopropyl alcohol and wipe with a fresh paper towel. And your PEX should be revitalized and ready to go!more information on Wham Bam: www.whambamsystems.com
Determining the right Wham Bam kit size for your printer Wham Bam Systems 2019-02-04 | this will show you how to determine your printer bed size and choose the best size Wham Bam kit for your machine.Currently Wham Bam offers the following kit sizes165 x 165 mm220 x 220 mm235 x 235 mm310 x 310 mm410 x 410 mm510 x 510 mmyou can find more information on fit here:whambamsystems.com/blog/f/what-size-flexible-build-system-for-your-3d-printerwww.whambamsystems.com
Unboxing The Flexible Build System by Wham Bam Wham Bam Systems 2019-01-29 | Here is a quick unboxing video showing how your Wham Bam kit will be shipped and what you will find inside the box. Visit our website for more information on kit contents and available sizes: whambamsystems.comIn the video, Peter is wearing one of our new t-shirts available for sale here: stores.inksoft.com/whambam/shop/homePrint With Confidence - Print sticks to build plate and build plate is secured to the printerRemove 3D Prints With Easy - Flexible build plate allows easy removal without a chiselUse Your Printer More Efficiently - Wham Bam Flexible Build System allows you to print edge to edge with no binder clips and quickly swap build plates for faster turnaround time on printsFollow us on social:facebook.com/WhamBamSystemstwitter.com/whambamsystemsinstagram.com/whambamsystemslinkedin.com/company/35445851#unboxing #WhamBam #3dprinting
