Ed CallahanThis is an actual 16mm film by Kearney Trecker. The original film was recorded in 1955. The original film has been converted to DVD compliments of an individual named ramsay1 from the Practical Machinist web site that sent me the DVDs to be shared here on youtube.
Kearney Trecker 2D Tool and Die Mill Jan 14, 1955 16mm FilmEd Callahan2015-12-31 | This is an actual 16mm film by Kearney Trecker. The original film was recorded in 1955. The original film has been converted to DVD compliments of an individual named ramsay1 from the Practical Machinist web site that sent me the DVDs to be shared here on youtube.1956 Dodge 315 poly 3rd and last part recutting port angles on 4 barrel intake manifoldEd Callahan2024-06-28 | Final part of the series . took .080 off one side .060 off other side now both are with in ..002 from each other intake was installed a couple hours later fit like it should didn't have to modify mounting bolt holes. I have some clips in here for Mr Pete showing the coordinate measuring system on my 2D Kearney and trecker milling machine , some pin up pictures for Dee Dee and a close up of the MVP fly cutter I used during the filming that Tim made.1956 dodge 315 poly part 2 cutting intake manifold runner flange to new angle using Devlieg 4H 60Ed Callahan2024-06-28 | Part 2 cutting other side, you can tell bottom right corner is .015 shy from the top corner was .000 .045 had been taken from both side in this episodeIntake manifold surfaced on Devlieg 4H 60 1956 dodge 315 poly v8 Part 1Ed Callahan2024-06-27 | 4 barrel intake manifold had wrong angles for cylinder heads approx 2 degrees on both sides plus plus gasket surfaces out of plane with each other.1956 Dodge 315 cylinder head surfacing by DevliegEd Callahan2024-03-01 | Devlieg struggling to cut cylinder head horizontal filmedDevlieg 4H 60 using MVP large fly cutter facing off John Deere 60 blockEd Callahan2023-12-12 | MVP brand fly cutter facing John Deere block another action packed video.Devlieg boring video very short, John Deere 60 block #1 cylinder.Ed Callahan2023-12-11 | Extremely short video boring John Deere 60 tractor cylinder block for .090 oversized pistons cylinder facing next video.Devlieg 4H 60 boring John Deere 60 tractor block cyl #1 .007 to go .Ed Callahan2023-12-11 | Boring #1 cylinder in John Deere block will be .090 oversized after honing.Boring John Deere 60 tractor cylinder block with devlieg 4H60 part 1Ed Callahan2023-12-04 | Boring cylinder block .090 over standard . was .045 over and laying outside in the weather for very long timeBullard vertical turret lathe boring out castingEd Callahan2023-11-17 | Boring hole in casting with devlieg boring bar held in jacobs flex collet chuck using Bullard vertical turret lathe couldn't swing in the Monarch1944 42 inch Bullard cutmaster turning footagEd Callahan2023-03-03 | More riveting footage .100 depth of facing cut ......more too come thanks for watchingArmstrong Blum power hacksaw footageEd Callahan2023-03-03 | Power hacksaw cutting through aluminum bronze with 4 T P I 14 inch blade.Kearney Trecker 2D and miscEd Callahan2023-02-14 | Making an aluminum bronze acme nut for screw lift table though I would use the 2D for the mounting boss.1944 BULLARD CUT MASTER more surfacing.testingEd Callahan2023-01-04 | Test cutting 12 inch plate facing cuts different feeds and speeds.1944 BULLARD 42 inch cut master first cutEd Callahan2022-12-26 | Bullard 's First cut .030 depth of cut. Facing 11 inch heavy wall pipe . Pretty riveting video1944 BULLARD test cut .060 depthEd Callahan2022-12-26 | Massive cut , seems to be struggling1944 Bullard test run with operable feed bracketsEd Callahan2022-11-23 | Got the feed brackets finished and coupled to the feed gearbox and rapid gear box Getting closer.1944 Bullard first test run on American rotary phase converterEd Callahan2022-11-20 | Just wired up the Bullard to phase converter and test run.1944 Bullard 42 inch cut master rebuildEd Callahan2022-08-20 | First spindle run up oil pressure checks . Machine drive pulley turning about 60 percent.Bullard cut master rebuild feed gear box housingEd Callahan2022-07-21 | Bullard housing for feed gear box boring and sleeping bronze bushing fits.42 inch Bullard cut master rebuildEd Callahan2022-07-21 | Bullard Vertical turret lathe rapid and feed gearbox bushing boring and sleeping using K&T 2H and walhaupter boring and facing head.Devlieg machining Chrysler exhaust manifoldEd Callahan2021-08-29 | Chrysler exhaust manifold had broken off mounting ear that extended into the runner, but I braised a replacement or downer ear from a 390 Ford exhaust manifold.Devlieg misc E table videoEd Callahan2020-10-23 | Rotating E table on 4H 60 devliegDevlieg in actionEd Callahan2020-10-23 | Trial Skim cutsDevlieg video e tableEd Callahan2020-10-23 | Devlieg 4H 60 with e table removedNew tool day 4H 60 devliegEd Callahan2020-10-23 | Using crane to move the devlieg to new homeDevlieg first cuts with MVP flycutterEd Callahan2020-09-24 | Devlieg flycuttingDevlieg E table first removalEd Callahan2020-09-23 | Devlieg table removedMore devliegEd Callahan2020-09-23 | More sea sick short videosDevlieg checking vertical squaring to table Rough leveledEd Callahan2020-09-20 | Crude video of first checks of devlieg machineKearney Trecker D milling machine universal milling attachment Part 2Ed Callahan2020-03-27 | A very short video of the attachment in use. Thanks edKearney Trecker Rotary D milling machine Universal milling attachment Part 1Ed Callahan2020-03-27 | A short video on the universal milling attachment, I had to make a drive gear adaptor and lost about 2 inches of Bork height above table. The attachment has the B3 collet in its spindle and the drive gear was same taper for the older K&T D mill. Mine has the 30 taper spindle with no drawbolt . It turned out very well looking to use it. This is part 1 thanks. Note toward the end you will see a oil sight glass it is on the power knee, when you run the knee you will see oil flowing across the back of the glass indicating oil pump is working on the knee lift motor thanks again edKearney tracker rotary head d mill , cherrying attachment in useEd Callahan2020-01-02 | 2D mill first use of cheering attachment hope you don't get sea sick thanks edKearney Trecker rotary d mill IMG 2022Ed Callahan2019-10-11 | Kearney Trecker late model D model milling machine , first test runMONARCH #60 set to bore wet sleeves for case tractorEd Callahan2017-10-18 | Monarch with fixtures to bore out wet sleeves .120 over size, you can't get the correct sleeves anymoreTRUE TRACE PART 2Ed Callahan2017-09-21 | A short clip of making a steel machine handle with home made templateMVI 1584 True trace lathe attachment in useEd Callahan2017-09-21 | First attempt at template making and use of true trace lathe attachment more to come.Hybco part 4Ed Callahan2017-04-07 | another short Hybco grinding film part 4Hybco relief grinder part3Ed Callahan2017-04-07 | Hybco relief grinding attachment grinding other countersinksHYBCO relief grinding attach Part2Ed Callahan2017-04-07 | hybco relief grinder attachment sharpening various countersinksHYBCO relief grinder part 1Ed Callahan2017-04-07 | Weldon countersink sharpening Hybco relief grinding attachment 1Glenbard SPI-RAD Relief Grinding part 2Ed Callahan2017-03-22 | Glenbard SPI-RAD Relief Grinding part 2Glenbard SPI-RAD Relief Grinding part 4Ed Callahan2017-03-22 | Glenbard SPI-RAD Relief Grinding part 4Glenbard SPI-RAD Relief Grinding part 3Ed Callahan2017-03-22 | Glenbard SPI-RAD Relief Grinding part 3Glenbard SPI-RAD Releif Grinder Part 1Ed Callahan2017-03-22 | GLENBARD SPI-RAD relief grinder attachment first takeKearney Trecker maching centerEd Callahan2017-03-01 | Kearney Trecker vintage maching center filmcutting a spur gear vintage filmEd Callahan2017-03-01 | cutting a spur gear on milling machine vintageArt of Reaming 2Ed Callahan2017-03-01 | Vintage footage of Machine Shop ReamingKearney Trecker Tri-D attachment Jan 28, 1955 16mm FilmEd Callahan2015-12-31 | This an actual 16mm film by Kearney Trecker. The original film was recorded in 1955. The original film has been converted to DVD compliments of an individual from the Practical Machinist web site that sent me the DVDs to be shared here on youtube.Kearney Trecker Tri-D Part 3Ed Callahan2015-12-22 | Kearney Trecker TRI-D Attachment in use no 3.